Transition from Cassie to impaled state during drop impact on groove-textured solid surfaces

Liquid drops impacted on textured surfaces undergo a transition from the Cassie state characterized by the presence of air pockets inside the roughness valleys below the drop to an impaled state with at least one of the roughness valleys filled with drop liquid. This occurs when the drop impact velocity exceeds a particular value referred to as the critical impact velocity. The present study investigates such a transition process during water drop impact on surfaces textured with unidirectional parallel grooves referred to as groove-textured surfaces. The process of liquid impalement into a groove in the vicinity of drop impact through de-pinning of the three-phase contact line (TPCL) beneath the drop as well as the critical impact velocity were identified experimentally from high speed video recordings of water drop impact on six different groove-textured surfaces made from intrinsically hydrophilic (stainless steel) as well as intrinsically hydrophobic (PDMS and rough aluminum) materials. The surface energy of various 2-D configurations of liquid-vapor interface beneath the drop near the drop impact point was theoretically investigated to identify the locally stable configurations and establish a pathway for the liquid impalement process. A force balance analysis performed on the liquid-vapor interface configuration just prior to TPCL de-pinning provided an expression for the critical drop impact velocity, U-o,U-cr, beyond which the drop state transitions from the Cassie to an impaled state. The theoretical model predicts that Uo, cr increases with the increase in pillar side angle, a, and intrinsic hydrophobicity whereas it decreases with the increase in groove top width, w, of the groove-textured surface. The quantitative predictions of the theoretical model were found to show good agreement with the experimental measurements of U-o,U-cr plotted against the surface texture geometry factor in our model, {tan(alpha/2)/w}(0.5).

Structural Diversity in Multinuclear PdII Assemblies that Show Low- Humidity Proton Conduction

Systematic investigation on synergetic effects of geometry, length, denticity, and asymmetry of donors was performed through the formation of a series of uncommon Pd-II aggregates by employing the donor in a multicomponent self-assembly of a cis-blocked 90 degrees Pd-II acceptor and a tetratopic donor. Some of these assemblies represent the first examples of these types of structures, and their formation is not anticipated by only taking the geometry of the donor and the acceptor building units into account. Analysis of the crystal packing of the X-ray structure revealed several H bonds between the counteranions (NO3-) and water molecules (OHON). Moreover, H-bonded 3D-networks of water are present in the molecular pockets, which show water-adsorption properties with some variation in water affinity. Interestingly, these complexes exhibit proton conductivity (1.87x10(-5)-6.52x10(-4)Scm(-1)) at 296K and low relative humidity (ca. 46%) with activation energies of 0.29-0.46eV. Moreover, the conductivities further increase with the enhancement of humidity. The ability of these assemblies to exhibit proton-conducting properties under low-humidity conditions makes these materials highly appealing as electrolytes in batteries and in fuel-cell applications.

Microstructure Development, Nanomechanical, and Dynamic Compression Properties of Spark Plasma Sintered TiB2-Ti-Based Homogeneous and Bi-layered Composites

The growing threats due to increased use of small-caliber armor piercing projectiles demand the development of new light-weight body armor materials. In this context, TiB2 appears to be a promising ceramic material. However, poor sinterability and low fracture toughness remain two major issues for TiB2. In order to address these issues together, Ti as a sinter-aid is used to develop TiB2-(x wt pct Ti), (x = 10, 20) homogeneous composites and a bi-layered composite (BLC) with each layer having Ti content of 10 and 20 wt pct. The present study uniquely demonstrates the efficacy of two-stage spark plasma sintering route to develop dense TiB2-Ti composites with an excellent combination of nanoscale hardness (similar to 36 GPa) and indentation fracture toughness (similar to 12 MPa m(1/2)). In case of BLC, these properties are not compromised w.r.t. homogeneous composites, suggesting the retention of baseline material properties even in the bi-layer design due to optimal relief of residual stresses. The better indentation toughness of TiB2-(10 wt pct Ti) and TiB2-(20 wt pct Ti) composites can be attributed to the observed crack deflection/arrest, indicating better damage tolerance. Transmission electron microscope investigation reveals the presence of dense dislocation networks and deformation twins in alpha-Ti at the grain boundaries and triple pockets, surrounded by TiB2 grains. The dynamic strength of around 4 GPa has been measured using Split Hopkinson Pressure Bar tests in a reproducible manner at strain rates of the order of 600 s(-1). The damage progression under high strain rate has been investigated by acquiring real time images for the entire test duration using ultra-high speed imaging. An attempt has been made to establish microstructure-property correlation and a simple analysis based on Mohr-Coulomb theory is used to rationalize the measured strength properties.

Controlling air solubility to maintain `'Cassie'' state for sustained drag reduction

`'Cassie'' state of wetting can be established by trapping air pockets on the crevices of textured hydrophobic surfaces, leading to significant drag reduction. However, this drag reduction cannot be sustained due to gradual dissolution of trapped air into water. In this paper, we explore the possibility of sustaining the underwater Cassie state of wetting in a microchannel by controlling the solubility of air in water; the solubility being changed by controlling the local absolute pressure near the surface. We show that using this method, we can in fact make the water locally supersaturated with air thus encouraging the growth of trapped air pockets on the surface. In this case, the water acts as a pumping medium, delivering air to the crevices of the hydrophobic surface in the microchannel, where the presence of air pockets is most beneficial from the drag reduction perspective. In our experiments, the air trapped on a textured surface is visualized using total internal reflection based technique, at different local absolute pressures with the pressure drop (or drag) also being simultaneously measured. We find that, by controlling the pressure and hence the solubility close to the surface, we can either shrink or grow the trapped air bubbles, uniformly over a large surface area. The experiments show that, by precisely controlling the pressure and hence the solubility we can sustain the `'Cassie state'' over extended periods of time. This method thus provides a means of getting sustained drag reduction from a textured hydrophobic surface in channel flows. (C) 2014 Elsevier B.V. All rights reserved.

Characterizing the pocketome of Mycobacterium tuberculosis and application in rationalizing polypharmacological target selection

Polypharmacology is beginning to emerge as an important concept in the field of drug discovery. However, there are no established approaches to either select appropriate target sets or design polypharmacological drugs. Here, we propose a structural-proteomics approach that utilizes the structural information of the binding sites at a genome-scale obtained through in-house algorithms to characterize the pocketome, yielding a list of ligands that can participate in various biochemical events in the mycobacterial cell. The pocket-type space is seen to be much larger than the sequence or fold-space, suggesting that variations at the site-level contribute significantly to functional repertoire of the organism. All-pair comparisons of binding sites within Mycobacterium tuberculosis (Mtb), pocket-similarity network construction and clustering result in identification of binding-site sets, each containing a group of similar binding sites, theoretically having a potential to interact with a common set of compounds. A polypharmacology index is formulated to rank targets by incorporating a measure of druggability and similarity to other pockets within the proteome. This study presents a rational approach to identify targets with polypharmacological potential along with possible drugs for repurposing, while simultaneously, obtaining clues on lead compounds for use in new drug-discovery pipelines.

The crystal structure of a lectin from Butea monosperma: Insight into its glycosylation and binding of ligands

Crystal structure of a lectin purified from Butea monosperma seeds was determined by Molecular Replacement method. Its primary structure was determined by Tandem Mass Spectroscopy and electron density maps from X-ray diffraction data. Its quaternary structure was tetrameric, formed of two monomers, alpha and beta, beta appearing as truncated alpha. The occurrence of two tetramers in the asymmetric unit of the crystal might be a consequence of asymmetric contacts due to difference in glycosylation and variable loops structures, to form an `octamer-structure'. The crystal structure showed binding pockets for gamma Abu, having a proposed role in plant defense, at the interface of canonical dimer-partners. Hemagglutination studies, enzyme kinetics, isothermal titration calorimetry and molecular dynamics showed that the lectin is specific to N-acetyl D-galactosamine, galactose and lactose in decreasing order, and alpha-amylase inhibitor. (C) 2014 Elsevier B.V. All rights reserved.

High thermopower and ultra low thermal conductivity in Cd-based Zintl phase compounds

By combining first principles density functional theory and electronic as well as lattice Boltzmann transport calculations, we unravel the excellent thermoelectric properties of Zintl phase compounds ACd(2)Sb(2) (where, A = Ca, Ba, Sr). The calculated electronic structures of these compounds show charge carrier pockets and heavy light bands near the band edge, which lead to a large power factor. Furthermore, we report large Gruneisen parameters and low phonon group velocity indicating essential strong anharmonicity in these compounds, which resulted in low lattice thermal conductivity. The combination of low thermal conductivity and the excellent transport properties give a high ZT value of similar to 1.4-1.9 in CaCd2Sb2 and BaCd2Sb2 at moderate p and n-type doping. Our results indicate that well optimized Cd-based Zintl phase compounds have the potential to match the performance of conventional thermoelectric materials.

Deciphering complex patterns of class-I HLA-peptide cross-reactivity via hierarchical grouping

T-cell responses in humans are initiated by the binding of a peptide antigen to a human leukocyte antigen (HLA) molecule. The peptide-HLA complex then recruits an appropriate T cell, leading to cell-mediated immunity. More than 2000 HLA class-I alleles are known in humans, and they vary only in their peptide-binding grooves. The polymorphism they exhibit enables them to bind a wide range of peptide antigens from diverse sources. HLA molecules and peptides present a complex molecular recognition pattern, as many peptides bind to a given allele and a given peptide can be recognized by many alleles. A powerful grouping scheme that not only provides an insightful classification, but is also capable of dissecting the physicochemical basis of recognition specificity is necessary to address this complexity. We present a hierarchical classification of 2010 class-I alleles by using a systematic divisive clustering method. All-pair distances of alleles were obtained by comparing binding pockets in the structural models. By varying the similarity thresholds, a multilevel classification was obtained, with 7 supergroups, each further subclassifying to yield 72 groups. An independent clustering performed based only on similarities in their epitope pools correlated highly with pocket-based clustering. Physicochemical feature combinations that best explain the basis of clustering are identified. Mutual information calculated for the set of peptide ligands enables identification of binding site residues contributing to peptide specificity. The grouping of HLA molecules achieved here will be useful for rational vaccine design, understanding disease susceptibilities and predicting risk of organ transplants.

Tuning the metal-insulator transition in NdNiO3 heterostructures via Fermi surface instability and spin fluctuations

We employed in situ pulsed laser deposition (PLD) and angle-resolved photoemission spectroscopy (ARPES) to investigate the mechanism of the metal-insulator transition (MIT) in NdNiO3 (NNO) thin films, grown on NdGaO3(110) and LaAlO3(100) substrates. In the metallic phase, we observe three-dimensional hole and electron Fermi surface (FS) pockets formed from strongly renormalized bands with well-defined quasiparticles. Upon cooling across the MIT in NNO/NGO sample, the quasiparticles lose coherence via a spectral weight transfer from near the Fermi level to localized states forming at higher binding energies. In the case of NNO/LAO, the bands are apparently shifted upward with an additional holelike pocket forming at the corner of the Brillouin zone. We find that the renormalization effects are strongly anisotropic and are stronger in NNO/NGO than NNO/LAO. Our study reveals that substrate-induced strain tunes the crystal field splitting, which changes the FS properties, nesting conditions, and spin-fluctuation strength, and thereby controls the MIT via the formation of an electronic order parameter with QAF similar to (1/4,1/4,1/4 +/- delta).

Joint Strength and Wall Deformation Characteristics of a Single-Cell Geocell Subjected to Uniaxial Compression

Geocells are three-dimensional expandable panels with a wide range of applications in geotechnical engineering. A geocell is made up of many internally connected single cells. The current study discusses the joint strength and the wall deformation characteristics of a single cell when it is subjected to uniaxial compression. The study helps to understand the causes for the failure of the single cell in a cellular confinement system. Experimental studies were conducted on single cells with cell pockets filled up with three different infill materials, namely silty clay, sand, and the aggregates. The results of the experimental study revealed that the deformation of the geocell wall decreases with the increase in the friction angle of the infill material. Experimental results were also validated using numerical simulations carried out using Lagrangian analysis software. The experiment and the numerical results were found to be in good agreement with each other. A simple analytical model based on the theory of thin cylinders is also proposed to calculate the accumulated strain of the geocell wall. This model operates under a simple elastic solution framework. The proposed model slightly overestimates the strains as compared with experimental and numerical values. (C) 2014 American Society of Civil Engineers.

Covalent Postassembly Modification and Water Adsorption of Pd3 Self-Assembled Trinuclear Barrels

Three new ditopic imidazole ligands (2-4) were synthesized in high yields and characterized by various spectroscopic techniques. These ligands resulted in the formation of 3 + 6] self-assembled trinuclear barrels (5-7) in quantitative yields by stoichiometric combination of individual ligands and Pd(NO3)(2) in DMSO. All the three assemblies (5-7) were characterized by `H NMR and ESI-MS analysis, and subsequently, structures of the complexes 5 and 6 were confirmed by single-crystal X-ray diffraction studies. Structure analysis reveals the presence of NO3- counter anions in the intermolecular channels/pockets, which could potentially act as H-bonding sites between adsorbed water molecules within the channels. In fact, both the assemblies (5 and 6) showed water uptake (136.58, and 123.78 cm(3) g(-1), respectively) at ambient temperature under maximum allowable humidity. In addition, free aldehyde group present in the bridging ligand in complex 7 provides reactive site for postassembly modification. Herein, Knoevenagel condensation with Meldrum's acid was utilized under mild conditions by targeting aldehyde group appended in prefabricated complex 7 and transformed into a different complex (8) with altered functional group. Such postassembly functionalization enables incorporation of a new functional group without disrupting the integrity of the trifacial structure.

12 steps towards embedding inclusive use of technology

This briefing for senior managers is based upon research conducted by Jisc via interviews with a range of pro-vice chancellors for Learning and Teaching (or equivalent). The briefing describes 12 steps that senior managers can take to lead and embed a culture of inclusive practice right across the institution, building on any pockets of excellence that already exist. TDL

Impacto da terapia mecânica não cirúrgica em pacientes com periodontite crônica e agressiva generalizadas

O objetivo deste estudo foi avaliar o impacto do tratamento periodontal não cirúrgico sobre a atividade de elastase e o volume de fluido gengival nos pacientes portadores de periodontite crônica e agressiva generalizadas. Foram avaliados 18 pacientes com periodontite crônica (idade média 48,6 DP 7,5 anos), e 11 com periodontite agressiva (idade média 27,9 DP 6,54 anos). Foram utilizados os parâmetros clínicos de avaliação de profundidade de bolsa à sondagem (PB) (mm), nível de inserção (NI) (mm) e sangramento à sondagem (SS). As medidas clínicas e as amostras de fluido gengival foram colhidas a partir dos cinco sítios mais profundos (P) e de cinco sítios rasos com gengivite (G) de cada paciente, antes e 90 dias após o término do tratamento. As etapas clínicas obedeceram ao seguinte cronograma: seleção e exame periodontal; coleta de fluido gengival; tratamento periodontal; reavaliação, compreendendo o exame periodontal e coleta de fluido gengival. O tratamento levou, em média, 4 sessões de 40 minutos cada por paciente, com intervalo de 1 semana entre elas. As consultas para reavaliação foram feitas 90 dias após o término do tratamento. O teste de Wilcoxon foi utilizado para comparar os dados antes e depois do tratamento e o teste não pareado de Mann-Whitney U-test foi utilizado para comparar os grupos de periodontite crônica e agressiva. A amostra analisada antes e após o tratamento não apresentou diferenças significativas entre o grupo com periodontite crônica e agressiva, que responderam de forma similar a todos os indicadores avaliados, exceto para a profundidade de bolsa à sondagem nos sítios rasos com gengivite (p = 0,039) e para o sangramento à sondagem (p = 0,021) nos sítios profundos, ambos mais reduzidos na periodontite crônica após o tratamento. A elastase apresentou, após o tratamento, redução significativa nos sítios profundos, para a periodontite crônica (p = 0,012) e agressiva (p = 0,02). Em relação ao volume de fluido gengival, houve significativa redução após o tratamento nos pacientes com periodontite crônica e agressiva, tanto nos sítios rasos (p = 0,03 e p = 0,03) como nos profundos (p ˂ 0,001 e p = 0,003), respectivamente. Concluindo, os grupos com periodontite crônica e agressiva generalizadas comportaram- se de maneira semelhante frente à terapia mecânica não cirúrgica. Ainda, a terapia periodontal mecânica não cirúrgica mostrou redução significativa do volume de fluido gengival em todos os sítios analisados, e da atividade neutrofílica, nos sítios profundos, associada a reduções significativas em todos os indicadores clínicos analisados após o tratamento.

Levantamento e estudo das ocorrências de grafita do Distrito Grafitífero Aracoiába-Baturité, CE

O Distrito Grafitífero Aracoiába-Baturité apresenta depósitos do tipo gnaisse grafitoso (minério disseminado) e veio (minério maciço) com diferentes origens genéticas e com características físicas e ambientes geológicos de formação próprios. O minério tipo gnaisse grafitoso é de origem sedimentar, singenético, com teores de 1,5 a 8% de C, que se distribuem ao longo de duas extensas faixas paralelas, hospedadas na Subunidade Baturité, que constitui um importante metalotecto regional. A associação de grafita metamórfica disseminada em metassedimentos da Sequência Acarápe constitui um geoindicador de antiga bacia sedimentar neoproterozóica e, também, pode ser considerado como zona de geosutura resultante do subsequente fechamento de um oceano primitivo. As rochas desta subunidade correspondem na paleogeografia da Sequência Acarápe aos fácies de sopé de talude e de planície abissal. O minério tipo veio (fluido depositado) é epigenético e, com teores entre 20% e 70% de C, forma corpos tabulares e bolsões, controlados em escala local por estruturas de alívio (falhas, fraturas, zonas de contato, eixos de dobras etc.) que permitiram a percolação de soluções penumatolíticas relacionadas ao corpo plutônico de Pedra Aguda. As variações dos valores das relações entre isótopos estáveis de carbono (δ13C) na grafita do minério disseminado são de -26,72 a -23,52 e do minério maciço de -27,03 a -20,83, revelando sinal de atividades biológicas (bioassinaturas) e permitem afirmar que a grafita das amostras acima são derivadas de matéria orgânica. Foram apresentados os principais guias de prospecção para grafita e testados os seguintes métodos geofísicos: Eletro-Resistividade; GPR - Ground Penetrating Radar; Magnetometria; VLF (Very Low Frequency); e Polarização Induzida Espectral (IPS) / Resistividade (ER). A conjugação dos métodos de Polarização Induzida Espectral (IPS) e Eletro Resistividade (ER) foi o que demonstrou a melhor eficiência. Com relação à determinação do teor de carbono por termogravimetria (ATG), que é o método mais utilizado para este elemento. Verificou-se, que as faixas de queima atribuídas ao carbono no minério do Distrito de Aracoiába-Baturité (340 a 570C e de 570 a 1050C) eram diferentes das faixas do minério de Minas Gerais (350C a 650C e 650C a 1.050C). Esta constatação indica a necessidade de se determinar previamente as faixas de temperatura para cada região pesquisada.

Expressão de fatores de virulência, mecanismos de resistência aos agentes antimicrobianos e análise molecular da resistência aos beta-lactâmicos de enterobactérias isoladas de bolsas periodontais

Em estudo anterior, as espécies de enterobactérias apresentando perfis variados de resistência aos antimicrobianos foram detectadas em 20% dos sítios com lesões periodontais de pacientes sadios do ponto de vista sistêmico. Tais cepas microbianas foram submetidas a investigações com o intuito de determinar à expressão de enzimas hidrolíticas para substratos diversos, a multirresistência aos agentes antimicrobianos e os mecanismos de resistência aos antimicrobianos da classe dos β lactâmicos. A maioria das amostras expressou atividade de gelatinase (65%), caseinase (30%) e elastase (10%). Lipase, lecitinase e DNase foram observadas apenas para Serratia marcescens. A multirresistência (considerado como a resistência a pelo menos dois agentes antimicrobianos de famílias diferentes) foi observada em 56% das amostras isoladas. A maioria das cepas foi resistentes à ampicilina (93,75%) e amoxicilina/ácido clavulânico (81,25%). Investigações sobre a resistência aos antibióticos β-lactâmicos mostraram que três amostras resistentes à cefalosporinas de 2 geração, apresentaram perfis plasmidiais de diferentes pesos moleculares. A expressão fenotípica de β-lacatamases, foi detectada nas cepas de Enterobacter cloacae (PcOM46 e PcOM5) e S. marcescens (PcOM63). No entanto, na análise molecular, não foi possível confirmar a expressão fenotípica de diferentes β-lactamases, com exceção do E. cloacae PcOM46, que apresentou amplificação para AmpC e blaTEM. Embora sensível à maioria dos antibióticos β-lactâmicos (exceção feita à ampicilina e amoxicilina / ácido clavulânico), amostra de S. marcescens PcOM68 apresentou amplificação para o gene blaSHV. Os experimentos de conjugação não detectaram a transferência de plasmídios para uma cepa de Escherichia coli K12 sensívei aos β-lactâmicos, o mesmo ocorreu nos procedimentos de transformação por eletroporação e por CaCl2, sugerindo uma resistência dependente de genes cromossomiais. A expressão de diferentes atividades enzimáticas, juntamente com a resistência aos antimicrobianos, aponta estes grupos de bactérias como agentes patogênicos potenciais capazes de contribuir para a patogênese e resposta à quimioterapia antimicrobiana nas doenças periodontais, além da disseminação sistêmica para outros locais do corpo, especialmente em indivíduos imunocomprometidos. A colonização prévia de lesões periodontais por espécies resistentes aos β-lactâmicos, pode contribuir para a disseminação destes genes relacionados à resistência aos antimicrobianos em ambientes hospitalares.