Centrifuge testing of monopile in clay under monotonic loads

The monopile is at present the most widely applied foundation concept for offshore wind turbines. Monopiles are designed utilising the well-established p-y method. Despite being well-established, there are multiple issues and limitations regarding its use. Investigation into the lateral behaviour of monopiles was carried out by performing monotonic and cyclic lateral load tests on an aluminium model monopile in the centrifuge. The monotonic responses and the behaviour of the monopile are described. Differences between the experimental and DNV design p-y curves and their implications are discussed. Efforts to characterise the shear force acting at the pile toe are also discussed. The results highlight the possible deficiencies of utilising the conventional DNV design p-y curves to design monopiles to resist cyclic lateral loads and the importance of research into the cyclic loading behaviour of monopiles to better improve their design to resist long-term cyclic loads. © 2014 Taylor & Francis Group.

Centrifuge testing of monopiles subject to cyclic lateral loading

Monopiles supporting offshore wind turbines are subjected to cyclic lateral loading. The properties of the applied cyclic lateral load are known to have an effect on the accumulation of permanent displacement and rotation at the pile head. The results of centrifuge testing on model piles show that certain loading regimes lead to the development of locked in soil stresses around the pile. These locked in soil stresses change the stiffness of the monopile response to cyclic lateral loading and the natural frequency of the pile-soil system. © 2014 Taylor & Francis Group.

SLP: A zero-contact non-invasive method for pulmonary function testing

Structured Light Plethysmography (SLP) is a novel non-invasive method that uses structured light to perform pulmonary function testing that does not require physical contact with a patient. The technique produces an estimate of chest wall volume changes over time. A patient is observed continuously by two cameras and a known pattern of light (i.e. structured light) is projected onto the chest using an off-the-shelf projector. Corner features from the projected light pattern are extracted, tracked and brought into correspondence for both camera views over successive frames. A novel self calibration algorithm recovers the intrinsic and extrinsic camera parameters from these point correspondences. This information is used to reconstruct a surface approximation of the chest wall and several novel ideas for 'cleaning up' the reconstruction are used. The resulting volume and derived statistics (e.g. FVC, FEV) agree very well with data taken with a spirometer. © 2010. The copyright of this document resides with its authors.

Validation of a parabolic trough solar receiver model based on physical formulation of the absorber total emissivity from its spectral emissivity

Concentrating solar power is an important way of providing renewable energy. Model simulation approaches play a fundamental role in the development of this technology and, for this, an accurately validation of the models is crucial. This work presents the validation of the heat loss model of the absorber tube of a parabolic trough plant by comparing the model heat loss estimates with real measurements in a specialized testing laboratory. The study focuses on the implementation in the model of a physical-meaningful and widely valid formulation of the absorber total emissivity depending on the surface’s temperature. For this purpose, the spectral emissivity of several absorber’s samples are measured and, with these data, the absorber total emissivity curve is obtained according to Planck function. This physical-meaningful formulation is used as input parameter in the heat loss model and a successful validation of the model is performed. Since measuring the spectral emissivity of the absorber surface may be complex and it is sample-destructive, a new methodology for the absorber’s emissivity characterization is proposed. This methodology provides an estimation of the absorber total emissivity, retaining its physical meaning and widely valid formulation according to Planck function with no need for direct spectral measurements. This proposed method is also successfully validated and the results are shown in the present paper.

Perceived acceptability of home-based couples voluntary HIV counseling and testing in Northern Tanzania.

It is estimated that 5.6% of the Tanzanian population ages 15-49 are infected with HIV, but only 30% of adults have ever had an HIV test. Couples' testing has proven to increase testing coverage and introduce HIV prevention, but barriers include access to testing services and unequal gender dynamics in relationships. Innovative approaches are needed to address barriers to couple's testing and increase uptake of HIV testing. Using qualitative data collection methods, a formative study was conducted to assess the acceptability of a home-based couples counseling and testing (HBCCT) approach. Eligible study participants included married men and women, HIV-infected individuals, health care and home-based care providers, voluntary counseling and testing counselors, and community leaders. A total of 91 individuals participated in focus group discussions (FGDs) and in-depth interviews conducted between September 2009 and January 2010 in rural settings in Northern Tanzania. An HBCCT intervention appears to be broadly acceptable among participants. Benefits of HBCCT were identified in terms of access, confidentiality, and strengthening the relationship. Fears of negative consequences from knowing one's HIV status, including stigma, blame, physical abuse, or divorce, remain a concern and a potential barrier to the successful provision of the intervention. Lessons for implementation highlighted the importance of appointments for home visits, building relationships of confidence and trust between counselors and clients, and assessing and responding to a couple's readiness to undergo HIV testing. HBCCT should addresses HIV stigma, emphasize confidentiality, and improve communication skills for disclosure and decision-making among couples.

Design, construction and testing of an air-cycle refrigeration system for road transport

The environmental attractions of air-cycle refrigeration are considerable. Following a thermodynamic design analysis, an air-cycle demonstrator plant was constructed within the restricted physical envelope of an existing Thermo King SL200 trailer refrigeration unit. This unique plant operated satisfactorily, delivering sustainable cooling for refrigerated trailers using a completely natural and safe working fluid. The full load capacity of the air-cycle unit at -20 °C was 7,8 kW, 8% greater than the equivalent vapour-cycle unit, but the fuel consumption of the air-cycle plant was excessively high. However, at part load operation the disparity in fuel consumption dropped from approximately 200% to around 80%. The components used in the air-cycle demonstrator were not optimised and considerable potential exists for efficiency improvements, possibly to the point where the air-cycle system could rival the efficiency of the standard vapour-cycle system at part-load operation, which represents the biggest proportion of operating time for most units.

Testing nonlocal realism with entangled coherent states

We investigate the violation of nonlocal realism using entangled coherent states (ECSs) under nonlinear operations and homodyne measurements. We address recently proposed Leggett-type inequalities, including a class of optimized incompatibility inequalities proposed by Branciard et al. [Nature Phys. 4, 681 (2008)], and thoroughly assess the effects of detection inefficiency.

Testing quantum contextuality of continuous-variable states

We investigate the violation of noncontextuality by a class of continuous-variable states, including variations of entangled coherent states and a two-mode continuous superposition of coherent states. We generalize the Kochen-Specker (KS) inequality discussed by Cabello [A. Cabello, Phys. Rev. Lett. 101, 210401 (2008)] by using effective bidimensional observables implemented through physical operations acting on continuous-variable states, in a way similar to an approach to the falsification of Bell-Clauser-Horne-Shimony-Holt inequalities put forward recently. We test for state-independent violation of KS inequalities under variable degrees of state entanglement and mixedness. We then demonstrate theoretically the violation of a KS inequality for any two-mode state by using pseudospin observables and a generalized quasiprobability function.

Physical properties of a new Deep Eutectic Solvent based on lithium bis[(trifluoromethyl)sulfonyl]imide and N-methylacetamide as superionic suitable electrolyte for lithium ion batteries and electric double layer capacitors

Herein we present a study on the physical/chemical properties of a new Deep Eutectic Solvent (DES) based on N-methylacetamide (MAc) and lithium bis[(trifluoromethyl)sulfonyl]imide (LiTFSI). Due to its interesting properties, such as wide liquid-phase range from -60°C to 280°C, low vapor pressure, and high ionic conductivity up to 28.4mScm at 150°C and at x=1/4, this solution can be practically used as electrolyte for electrochemical storage systems such as electric double-layer capacitors (EDLCs) and/or lithium ion batteries (LiBs). Firstly, relationships between its transport properties (conductivity and viscosity) as a function of composition and temperature were discussed through Arrhenius' Law and Vogel-Tamman-Fulcher (VTF) equations, as well as by using the Walden classification. From this investigation, it appears that this complex electrolyte possesses a number of excellent transport properties, like a superionic character for example. Based on which, we then evaluated its electrochemical performances as electrolyte for EDLCs and LiBs applications by using activated carbon (AC) and lithium iron phosphate (LiFePO) electrodes, respectively. These results demonstrate that this electrolyte has a good compatibility with both electrodes (AC and LiFePO) in each testing cell driven also by excellent electrochemical properties in specific capacitance, rate and cycling performances, indicating that the LiTFSI/MAc DES can be a promising electrolyte for EDLCs and LiBs applications especially for those requiring high safety and stability. © 2013 Elsevier Ltd.

Impact of Testing Procedure on Permeability of Compacted Soils

The commonly used British Standard constant head triaxial permeability (BS) test, for permeability testing of fine grained soils, is known to have a relatively long test duration. Consequently, a reduction in the required time for permeability test provides potential cost savings, to the construction industry (specifically, for use during Construction Quality Control (CQA) of landfill mineral liners). The purpose of this article is to investigate and evaluate alternative short duration testing methods for the measurement of the permeability of fine grained soils.

As part of the investigation the feasibility of an existing method of short duration permeability test, known as the Accelerated Permeability (AP) test was assessed and compared with permeability measured using British Standard method (BS) and Ramp Accelerated Permeability (RAP). Four different fine grained materials, of a variety of physical properties were compacted at various moisture contents to produced analogous samples for testing using three the three different methodologies. Fabric analysis was carried out on specimens derived from post-test samples using Mercury Intrusion Porosimetry (MIP) and Scanning Electron Microscope (SEM) to assess the effects of testing methodology on soil structure. Results showed that AP testing in general under predicts permeability values derived from the BS test due to large changes in structure of the soil caused by AP test methodology, which is also validated using MIP and SEM observations. RAP testing, in general provides an improvement to the AP test but still under-predicts permeability values. The potential savings in test duration are shown to be relatively minimal for both the AP and RAP tests.

Testing genuine multipartite nonlocality in phase spacea

We demonstrate genuine three-mode nonlocality based on phase-space formalism. A Svetlichny-type Bell inequality is formulated in terms of the s-parametrized quasiprobability function. We test such a tool using exemplary forms of three-mode entangled states, identifying the ideal measurement settings required for each state. We thus verify the presence of genuine three-mode nonlocality that cannot be reproduced by local or nonlocal hidden variable models between any two out of three modes. In our results, GHZ- and W-type nonlocality can be fully discriminated. We also study the behavior of genuine tripartite nonlocality under the effects of detection inefficiency and dissipation induced by local thermal environments. Our formalism can be useful to test the sharing of genuine multipartite quantum correlations among the elements of some interesting physical settings, including arrays of trapped ions and intracavity ultracold atoms. DOI: 10.1103/PhysRevA.87.022123

Design of Scaled Bridge Prototype for Energy Harvesting Testing

Energy harvesting from ambient vibration is a promising field, especially for applications in larger infrastructures such as bridges. These structures are more frequently monitored for damage detection because of their extended life, increased traffic load and environmental deterioration. In this regard, the possibility of sourcing the power necessary for the sensors from devices embedded in the structure, thus cutting the cost due to the management of battery replacing over the lifespan of the structure, is particularly attracting. Among others, piezoelectric devices have proven to be especially effective and easy to apply since they can be bonded to existing host structure. For these devices the energy harvesting capacity is achieved directly from the variation in the strain conditions from the surface of the structure. However these systems need to undergo significant research for optimisation of their harvesting capacity and for assessing the feasibility of application to various ranges of bridge span and load. In this regard scaled bridge prototypes can be effectively used not only to assess numerical models and studies in an inexpensive and repeatable way but also to test the electronic devices under realistic field conditions. In this paper the theory of physical similitude is applied to the design of bridge beams with embedded energy harvesting systems and health monitoring sensors. It will show both how bridge beams can be scaled in such a way to apply and test energy harvesting systems and 2) how experimental data from existing bridges can be applied to prototypes in a laboratory environment. The study will be used for assessing the reliability of the system over a train bridge case study undergoing a set load cycles and induced localised damage.

Testing numerical implementations of strong-field electrodynamics

We test current numerical implementations of laser-matter interactions by comparison with exact analytical results. Focusing on photon emission processes, it is found that the numerics accurately reproduce analytical emission spectra in all considered regimes, except for the harmonic structures often singled out as the most significant high-intensity (multiphoton) effects. We find that this discrepancy originates in the use of the locally constant field approximation.

Designing for dementia : an assessment of the impact of the physical environment on wayfinding success for residents in long term care settings

It is acknowledged that one of the consequences of the ageing process is cognitive decline, which leads to an increase in the incidence of illnesses such as dementia. This has become ever more relevant due to the projected increase in the ageing demographic. Dementia affects visuo-spatial perception, causing difficulty with wayfinding, even during the early stages of the disease. The literature widely recognises the physical environment’s role in alleviating symptoms of dementia and improving quality of life for residents. It also identifies the lack of available housing options for older people with dementia and consequently the current stock is ill-equipped to provide adequate support.
Recent statistics indicate that 80% of those residing in nursing or residential care homes have some form of dementia or severe memory problems. The shift towards institutional care settings, the need for specialist support and care, places a greater impetus on the need for a person-centred approach to tackle issues related to wayfinding and dementia.
This thesis therefore aims to improve design for dementia in nursing and residential care settings in the context of Northern Ireland. This will be undertaken in order to provide a better understanding of how people with dementia experience the physical environment and to highlight features of the design that assist with wayfinding. Currently there are limited guidelines on design for dementia, meaning that many of these are theoretical, anecdotal and not definitive. Hence a greater verification to address the less recognised design issues is required. This is intended to ultimately improve quality of life, wellbeing, independence and uphold the dignity of people with dementia living in nursing or residential care homes.
The research design uses a mixed methods approach. A thorough preparation and consideration of ethical issues informed the methodology. The various facets were also trialled and piloted to identify any ethical, technological, methodological, data collection and analysis issues. The protocol was then amended to improve or resolve any of the aforementioned issues. Initially a questionnaire based on leading design recommendations was conducted with home managers. Semi-structured interviews were developed from this and conducted with staff and resident’s next of kin. An evidence-based approach was used to design a study which used ethnographic methods, including a wayfinding task. This followed a repeated measures design which would be used to actively engage residents with dementia in the research. Complementary to the wayfinding task, conversational and semi-structured interviews were used to promote dialogue and direct responses with the person with dementia. In addition to this, Space Syntax methodologies were used to examine the physical properties of the architectural layout. This was then cross-examined with interview responses and data from the wayfinding tasks.
A number of plan typologies were identified and were determined as synonymous with decision point types which needed to be made during the walks. The empirical work enabled the synthesis of environmental features which support wayfinding.
Results indicate that particular environmental features are associated with improved performance on the wayfinding tasks. By enhancing design for dementia, through identifying the attributes, challenges with wayfinding may be overcome and the benefits of the physical environment can be seen to promote wellbeing.
The implications of this work mean that the environmental features which have been highlighted from the project can be used to inform guidelines, thus adding to existing knowledge. Future work would involve the dissemination of this information and the potential for it to be made into design standards or regulations which champion design for dementia. These would increase awareness for designers and stakeholders undertaking new projects, extensions or refurbishments.
A person-centred, evidence-based design was emphasised throughout the project which guaranteed an in-depth study. There were limitations due to the available resources, time and funding. Future research would involve testing the identified environmental features within a specific environment to enable measured observation of improvements.

Investigating Cyber-Physical Attacks against IEC 61850 Photovoltaic Inverter Installations

Cyber-attacks against Smart Grids have been found in the real world. Malware such as Havex and BlackEnergy have been found targeting industrial control systems (ICS) and researchers have shown that cyber-attacks can exploit vulnerabilities in widely used Smart Grid communication standards. This paper addresses a deep investigation of attacks against the manufacturing message specification of IEC 61850, which is expected to become one of the most widely used communication services in Smart Grids. We investigate how an attacker can build a custom tool to execute man-in-the-middle attacks, manipulate data, and affect the physical system. Attack capabilities are demonstrated based on NESCOR scenarios to make it possible to thoroughly test these scenarios in a real system. The goal is to help understand the potential for such attacks, and to aid the development and testing of cyber security solutions. An attack use-case is presented that focuses on the standard for power utility automation, IEC 61850 in the context of inverter-based distributed energy resource devices; especially photovoltaic (PV) generators.