Processos de avaliação dos pavimentos rodoviários: Caso de estudo: reforço do pavimento em dois trechos do sublanço Enxara/Torres Vedras Sul

Relatório de Estágio Curricular para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização de Vias de Comunicação e Transportes

Caracterização física e química de fíleres para fabrico de misturas betuminosas

Mestrado em Engenharia Geotécnica e Geoambiente

A influência dos fileres no comportamento viscoso dos mastiques betuminosos

As estradas têm vindo a sofrer um aumento de importância, sendo necessário aplicar pavimentos com melhores características, assim foram desenvolvidos os mastiques betuminosos. Os mastiques são misturas de betume com filer, este material tem propriedades melhoradas em relação ao betume puro. O betume é um material viscoelástico, o que leva a que a viscosidade seja uma propriedade de vital importância estudar. A junção de fileres ao betume promove um aumento de viscosidade, levando a que esta propriedade reológica tenha ainda mais importância, principalmente porque a trabalhabilidade da mistura betuminosa fica comprometida quando a viscosidade não é a correta. Na realização desta dissertação foram realizados ensaios em mastiques betuminosos, com recurso ao viscosímetro rotativo de Brookfield. Os mastiques ensaiados são compostos com fileres de diferentes origens e com diferentes taxas de incorporação, e assim foram analisadas as diferenças obtidas nos valores da viscosidade dinâmica. Os resultados obtidos mostram que os mastiques, à temperatura de fabrico, têm um comportamento viscoso idêntico ao comportamento viscoso do betume puro. Apesar dos mastiques produzidos terem uma viscosidade maior que a do betume puro, o valor desta propriedade reológica tende a igualar ao valor do betume, este comportamento observa-se nas temperaturas mais elevadas. Quando se examinam os resultados dos mastiques produzidos com menor quantidade de filer, na generalidade, os valores da viscosidade obtidos são idênticos. Para taxas de incorporação maiores, os valores da viscosidade dinâmica dos mastiques produzidos são bastante mais altos e distintos. Levando a concluir que quanto maior a percentagem de filer no mastique, maior o valor da viscosidade e maior dispersão dos resultados obtidos, isto para os fileres e taxas de incorporação testadas.

Receipt from Henry O’Laughlin, dealer in Anthracite and Bituminous Coals, St. Catharines

Receipt from Henry O’Laughlin, dealer in Anthracite and Bituminous Coals, St. Catharines for payment on account, Nov. 15, 1887.

A practical on roads, streets, and pavements

UANL

Influence of additives on the charactaristics of stone matrix asphalt

The increase in traffic growth and maintenance expenditures demands the urgent need for building better, long-lasting, and more efficient roads preventing or minimizing bituminous pavement distresses. Many of the principal distresses in pavements initiate or increase in severity due to the presence of water. In Kerala highways, where traditional dense graded mixtures are used for the surface courses, major distress is due to moisture induced damages. The Stone Matrix Asphalt (SMA) mixtures provide a durable surface course. Proven field performance of test track at Delhi recommends Stone Matrix Asphalt as a right choice to sustain severe climatic and heavy traffic conditions. But the concept of SMA in India is not so popularized and its application is very limited mainly due to the lack of proper specifications. This research is an attempt to study the influence of additives on the characteristics of SMA mixtures and to propose an ideal surface course for the pavements. The additives used for this investigation are coir, sisal, banana fibres (natural fibres), waste plastics (waste material) and polypropylene (polymer). A preliminary investigation is conducted to characterize the materials used in this study. Marshall test is conducted for optimizing the SMA mixtures (Control mixture-without additives and Stabilized mixtures with additives). Indirect tensile strength tests, compression strength tests, triaxial strength tests and drain down sensitivity tests are conducted to study the engineering properties of stabilized mixtures. The comparison of the performance of all stabilized mixtures with the control mixture and among themselves are carried out. A statistical analysis (SPSS package Ver.16) is performed to establish the findings of this study

A study on the performance of flexible pavements on mature soil subgrades

The country has witnessed tremendous increase in the vehicle population and increased axle loading pattern during the last decade, leaving its road network overstressed and leading to premature failure. The type of deterioration present in the pavement should be considered for determining whether it has a functional or structural deficiency, so that appropriate overlay type and design can be developed. Structural failure arises from the conditions that adversely affect the load carrying capability of the pavement structure. Inadequate thickness, cracking, distortion and disintegration cause structural deficiency. Functional deficiency arises when the pavement does not provide a smooth riding surface and comfort to the user. This can be due to poor surface friction and texture, hydro planning and splash from wheel path, rutting and excess surface distortion such as potholes, corrugation, faulting, blow up, settlement, heaves etc. Functional condition determines the level of service provided by the facility to its users at a particular time and also the Vehicle Operating Costs (VOC), thus influencing the national economy. Prediction of the pavement deterioration is helpful to assess the remaining effective service life (RSL) of the pavement structure on the basis of reduction in performance levels, and apply various alternative designs and rehabilitation strategies with a long range funding requirement for pavement preservation. In addition, they can predict the impact of treatment on the condition of the sections. The infrastructure prediction models can thus be classified into four groups, namely primary response models, structural performance models, functional performance models and damage models. The factors affecting the deterioration of the roads are very complex in nature and vary from place to place. Hence there is need to have a thorough study of the deterioration mechanism under varied climatic zones and soil conditions before arriving at a definite strategy of road improvement. Realizing the need for a detailed study involving all types of roads in the state with varying traffic and soil conditions, the present study has been attempted. This study attempts to identify the parameters that affect the performance of roads and to develop performance models suitable to Kerala conditions. A critical review of the various factors that contribute to the pavement performance has been presented based on the data collected from selected road stretches and also from five corporations of Kerala. These roads represent the urban conditions as well as National Highways, State Highways and Major District Roads in the sub urban and rural conditions. This research work is a pursuit towards a study of the road condition of Kerala with respect to varying soil, traffic and climatic conditions, periodic performance evaluation of selected roads of representative types and development of distress prediction models for roads of Kerala. In order to achieve this aim, the study is focused into 2 parts. The first part deals with the study of the pavement condition and subgrade soil properties of urban roads distributed in 5 Corporations of Kerala; namely Thiruvananthapuram, Kollam, Kochi, Thrissur and Kozhikode. From selected 44 roads, 68 homogeneous sections were studied. The data collected on the functional and structural condition of the surface include pavement distress in terms of cracks, potholes, rutting, raveling and pothole patching. The structural strength of the pavement was measured as rebound deflection using Benkelman Beam deflection studies. In order to collect the details of the pavement layers and find out the subgrade soil properties, trial pits were dug and the in-situ field density was found using the Sand Replacement Method. Laboratory investigations were carried out to find out the subgrade soil properties, soil classification, Atterberg limits, Optimum Moisture Content, Field Moisture Content and 4 days soaked CBR. The relative compaction in the field was also determined. The traffic details were also collected by conducting traffic volume count survey and axle load survey. From the data thus collected, the strength of the pavement was calculated which is a function of the layer coefficient and thickness and is represented as Structural Number (SN). This was further related to the CBR value of the soil and the Modified Structural Number (MSN) was found out. The condition of the pavement was represented in terms of the Pavement Condition Index (PCI) which is a function of the distress of the surface at the time of the investigation and calculated in the present study using deduct value method developed by U S Army Corps of Engineers. The influence of subgrade soil type and pavement condition on the relationship between MSN and rebound deflection was studied using appropriate plots for predominant types of soil and for classified value of Pavement Condition Index. The relationship will be helpful for practicing engineers to design the overlay thickness required for the pavement, without conducting the BBD test. Regression analysis using SPSS was done with various trials to find out the best fit relationship between the rebound deflection and CBR, and other soil properties for Gravel, Sand, Silt & Clay fractions. The second part of the study deals with periodic performance evaluation of selected road stretches representing National Highway (NH), State Highway (SH) and Major District Road (MDR), located in different geographical conditions and with varying traffic. 8 road sections divided into 15 homogeneous sections were selected for the study and 6 sets of continuous periodic data were collected. The periodic data collected include the functional and structural condition in terms of distress (pothole, pothole patch, cracks, rutting and raveling), skid resistance using a portable skid resistance pendulum, surface unevenness using Bump Integrator, texture depth using sand patch method and rebound deflection using Benkelman Beam. Baseline data of the study stretches were collected as one time data. Pavement history was obtained as secondary data. Pavement drainage characteristics were collected in terms of camber or cross slope using camber board (slope meter) for the carriage way and shoulders, availability of longitudinal side drain, presence of valley, terrain condition, soil moisture content, water table data, High Flood Level, rainfall data, land use and cross slope of the adjoining land. These data were used for finding out the drainage condition of the study stretches. Traffic studies were conducted, including classified volume count and axle load studies. From the field data thus collected, the progression of each parameter was plotted for all the study roads; and validated for their accuracy. Structural Number (SN) and Modified Structural Number (MSN) were calculated for the study stretches. Progression of the deflection, distress, unevenness, skid resistance and macro texture of the study roads were evaluated. Since the deterioration of the pavement is a complex phenomena contributed by all the above factors, pavement deterioration models were developed as non linear regression models, using SPSS with the periodic data collected for all the above road stretches. General models were developed for cracking progression, raveling progression, pothole progression and roughness progression using SPSS. A model for construction quality was also developed. Calibration of HDM–4 pavement deterioration models for local conditions was done using the data for Cracking, Raveling, Pothole and Roughness. Validation was done using the data collected in 2013. The application of HDM-4 to compare different maintenance and rehabilitation options were studied considering the deterioration parameters like cracking, pothole and raveling. The alternatives considered for analysis were base alternative with crack sealing and patching, overlay with 40 mm BC using ordinary bitumen, overlay with 40 mm BC using Natural Rubber Modified Bitumen and an overlay of Ultra Thin White Topping. Economic analysis of these options was done considering the Life Cycle Cost (LCC). The average speed that can be obtained by applying these options were also compared. The results were in favour of Ultra Thin White Topping over flexible pavements. Hence, Design Charts were also plotted for estimation of maximum wheel load stresses for different slab thickness under different soil conditions. The design charts showed the maximum stress for a particular slab thickness and different soil conditions incorporating different k values. These charts can be handy for a design engineer. Fuzzy rule based models developed for site specific conditions were compared with regression models developed using SPSS. The Riding Comfort Index (RCI) was calculated and correlated with unevenness to develop a relationship. Relationships were developed between Skid Number and Macro Texture of the pavement. The effort made through this research work will be helpful to highway engineers in understanding the behaviour of flexible pavements in Kerala conditions and for arriving at suitable maintenance and rehabilitation strategies. Key Words: Flexible Pavements – Performance Evaluation – Urban Roads – NH – SH and other roads – Performance Models – Deflection – Riding Comfort Index – Skid Resistance – Texture Depth – Unevenness – Ultra Thin White Topping

Classification of recycled sands and their applications as fine aggregates for concrete and bituminous mixtures

As a result of the drive towards waste-poor world and reserving the non-renewable materials, recycling the construction and demolition materials become very essential. Now reuse of the recycled concrete aggregate more than 4 mm in producing new concrete is allowed but with natural sand a fine aggregate while. While the sand portion that represent about 30\% to 60\% of the crushed demolition materials is disposed off. To perform this research, recycled concrete sand was produced in the laboratory while nine recycled sands produced from construction and demolitions materials and two sands from natural crushed limestone were delivered from three plants. Ten concrete mix designs representing the concrete exposition classes XC1, XC2, XF3 and XF4 according to European standard EN 206 were produced with partial and full replacement of natural sand by the different recycled sands. Bituminous mixtures achieving the requirements of base courses according to Germany standards and both base and binder courses according to Egyptian standards were produced with the recycled sands as a substitution to the natural sands. The mechanical properties and durability of concrete produced with the different recycled sands were investigated and analyzed. Also the volumetric analysis and Marshall test were performed hot bituminous mixtures produced with the recycled sands. According to the effect of replacement the natural sand by the different recycled sands on the concrete compressive strength and durability, the recycled sands were classified into three groups. The maximum allowable recycled sand that can be used in the different concrete exposition class was determined for each group. For the asphalt concrete mixes all the investigated recycled sands can be used in mixes for base and binder courses up to 21\% of the total aggregate mass.

Estimated lifetimes of road pavements in Sweden using time-to-event analysis

Maintenance planning of road pavement requires reliable estimates of roads’ lifetimes. In determining the lifetime of a road, this study combines maintenance activities and road condition measurements. The scope of the paper is to estimate lifetimes of road pavements in Sweden with time to event analysis. The model used includes effects of pavement type, road type, bearing capacity, road width, speed limit, stone size and climate zone, where the model is stratified according to traffic load. Among the nine analyzed pavement types, stone mastic had the longest expected lifetime, 32 percent longer than asphalt concrete. Among road types, ordinary roads with cable barriers had 30 percent shorter lifetime than ordinary roads. Increased speed lowered the lifetime, while increased stone size (up to 20 mm) and increased road width lengthened the lifetime. The results are of importance for life cycle cost analysis and road management.

In situ stabilisation of pavements using cementitious binders

An extensive study was made of the physical properties of a range of cementitiously stabilised materials to determine their suitability for use in in situ pavement construction. This process for recycling existing pavements has considerable environmental and cost benefits. Pavement models incorporating these materials were analysed to determine their structural behaviour.

Pavements and pathways

A one-day interdisciplinary collaborative performance event exploring Mobility and the city. A Deakin-Monash collaboration in which project participants will engage in the interactive remapping of the City in a creative place-making event.

Comparison of the n-Alkanes and Polycyclic Aromatic Hydrocarbons Concentrations in the Atmosphere during the Preparation of Warm and Hot Mixtures Asphalt for Pavements

Asphalt binder is used in the production of hot mixes asphalt (HMA) for paving and, due to the high temperatures used, generates fumes thatcontainn-alkanes and polycyclic aromatic hydrocarbons (PAH). Asphalt mixes prepared at lower temperatures, such as warm mixes asphalt (WMA), may contribute to reduce the emissions of those compounds and save energy. This paper investigatesn-alkanes and PAH in the total suspended particles during the preparation of WMA, in comparison with HMA, in laboratory. The results showed that the n-alkanes of the WMA and HMA presented C-max at n-C-26 and n-C-28, respectively; also, the total content of n-alkanes was higher for the HMA than forthe WMA. Besides, benzo[b]fluoranthene and benzo[a]anthracene were the major PAH in the WMA, while the higher temperatures of the HMA were observed to volatilize all larger PAH, demonstrating higher potential of inhalation exposure.

Comparison of the n-alkanes and polycyclic aromatic hydrocarbons concentrations in the atmosphere during the preparation of warm and hot mixtures asphalt for pavements

O asfalto é utilizado na produção de misturas asfálticas a quente (HMA) para a pavimentação e, devido às altas temperaturas empregadas, gera fumos que contêm n-alcanos e hidrocarbonetos policíclicos aromáticos (HPAs). As misturas asfálticas preparadas em temperaturas mais baixas, como as misturas asfálticas mornas (WMA), podem contribuir na redução das emissões daqueles compostos e economizar energia. Este trabalho investiga os n-alcanos e os HPAs nas partículas totais em suspensão durante a preparação de uma WMA, em comparação com uma HMA, em laboratório. Os resultados mostraram que os n-alcanos da WMA e da HMA apresentaram Cmáx no n-C26 e n-C28, respectivamente, e o teor de n-alcanos total foi maior na HMA do que na WMA. Ademais, verificou-se que o benzo[b]fluoranteno e benzo[a]antraceno constituíam os maiores HPAs na WMA, enquanto as temperaturas mais altas da HMA volatilizaram todos seus grandes HPAs, demonstrando maior potencial de exposição por inalação.

Performance evaluation of asphalt pavements using the Incremental-Recursive procedure of the Mechanistic-Empirical design software CalME

Il concetto di “sostenibilità” si riferisce allo sviluppo dei sistemi umani attraverso il più piccolo impatto possibile sul sistema ambientale. Le opere che si inseriscono bene nel contesto ambientale circostante e le pratiche che rispettano le risorse in maniera tale da permettere una crescita e uno sviluppo a lungo termine senza impattare sull’ambiente sono indispensabili in una società moderna. I progressi passati, presenti e futuri che hanno reso i conglomerati bituminosi materiali sostenibili dal punto di vista ambientale sono particolarmente importanti data la grande quantità di conglomerato usato annualmente in Europa e negli Stati Uniti. I produttori di bitume e di conglomerato bituminoso stanno sviluppando tecniche innovative per ridurre l’impatto ambientale senza compromettere le prestazioni meccaniche finali. Un conglomerato bituminoso ad “alta lavorabilità” (WMA), pur sviluppando le stesse caratteristiche meccaniche, richiede un temperatura di produzione minore rispetto a quella di un tradizionale conglomerato bituminoso a caldo (HMA). L’abbassamento della temperature di produzione riduce le emissioni nocive. Questo migliora le condizioni dei lavoratori ed è orientato verso uno sviluppo sostenibile. L’obbiettivo principale di questa tesi di laurea è quello di dimostrare il duplice valore sia dal punto di vista dell’eco-compatibilità sia dal punto di vista meccanico di questi conglomerati bituminosi ad “alta lavorabilità”. In particolare in questa tesi di laurea è stato studiato uno SMA ad “alta lavorabilità” (PGGWMA). L’uso di materiali a basso impatto ambientale è la prima fase verso un progetto ecocompatibile ma non può che essere il punto di partenza. L’approccio ecocompatibile deve essere esteso anche ai metodi di progetto e alla caratterizzazione di laboratorio dei materiali perché solo in questo modo è possibile ricavare le massime potenzialità dai materiali usati. Un’appropriata caratterizzazione del conglomerato bituminoso è fondamentale e necessaria per una realistica previsione delle performance di una pavimentazione stradale. La caratterizzazione volumetrica (Mix Design) e meccanica (Deformazioni Permanenti e Comportamento a fatica) di un conglomerato bituminoso è una fase importante. Inoltre, al fine di utilizzare correttamente i materiali, un metodo di progetto avanzato ed efficiente, come quello rappresentato da un approccio Empirico-Meccanicistico (ME), deve essere utilizzato. Una procedura di progetto Empirico-Meccanicistica consiste di un modello strutturale capace di prevedere gli stati di tensione e deformazione all’interno della pavimentazione sotto l’azione del traffico e in funzione delle condizioni atmosferiche e di modelli empirici, calibrati sul comportamento dei materiali, che collegano la risposta strutturale alle performance della pavimentazione. Nel 1996 in California, per poter effettivamente sfruttare i benefici dei continui progressi nel campo delle pavimentazioni stradali, fu iniziato un estensivo progetto di ricerca mirato allo sviluppo dei metodi di progetto Empirico - Meccanicistici per le pavimentazioni stradali. Il risultato finale fu la prima versione del software CalME che fornisce all’utente tre approcci diversi di l’analisi e progetto: un approccio Empirico, uno Empirico - Meccanicistico classico e un approccio Empirico - Meccanicistico Incrementale - Ricorsivo. Questo tesi di laurea si concentra sulla procedura Incrementale - Ricorsiva del software CalME, basata su modelli di danno per quanto riguarda la fatica e l’accumulo di deformazioni di taglio dai quali dipendono rispettivamente la fessurazione superficiale e le deformazioni permanenti nella pavimentazione. Tale procedura funziona per incrementi temporali successivi e, usando i risultati di ogni incremento temporale, ricorsivamente, come input dell’incremento temporale successivo, prevede le condizioni di una pavimentazione stradale per quanto riguarda il modulo complesso dei diversi strati, le fessurazioni superficiali dovute alla fatica, le deformazioni permanenti e la rugosità superficiale. Al fine di verificare le propreità meccaniche del PGGWMA e le reciproche relazioni in termini di danno a fatica e deformazioni permanenti tra strato superficiale e struttura della pavimentazione per fissate condizioni ambientali e di traffico, è stata usata la procedura Incrementale – Ricorsiva del software CalME. Il conglomerato bituminoso studiato (PGGWMA) è stato usato in una pavimentazione stradale come strato superficiale di 60 mm di spessore. Le performance della pavimentazione sono state confrontate a quelle della stessa pavimentazione in cui altri tipi di conglomerato bituminoso sono stati usati come strato superficiale. I tre tipi di conglomerato bituminoso usati come termini di paragone sono stati: un conglomerato bituminoso ad “alta lavorabilità” con granulometria “chiusa” non modificato (DGWMA), un conglomerato bituminoso modificato con polverino di gomma con granulometria “aperta” (GGRAC) e un conglomerato bituminoso non modificato con granulometria “chiusa” (DGAC). Nel Capitolo I è stato introdotto il problema del progetto ecocompatibile delle pavimentazioni stradali. I materiali a basso impatto ambientale come i conglomerati bituminosi ad “alta lavorabilità” e i conglomerati bituminosi modificati con polverino di gomma sono stati descritti in dettaglio. Inoltre è stata discussa l’importanza della caratterizzazione di laboratorio dei materiali e il valore di un metodo razionale di progetto delle pavimentazioni stradali. Nel Capitolo II sono stati descritti i diversi approcci progettuali utilizzabili con il CalME e in particolare è stata spiegata la procedura Incrementale – Ricorsiva. Nel Capitolo III sono state studiate le proprietà volumetriche e meccaniche del PGGWMA. Test di Fatica e di Deformazioni Permanenti, eseguiti rispettivamente con la macchina a fatica per flessione su quattro punti e il Simple Shear Test device (macchina di taglio semplice), sono stati effettuati su provini di conglomerato bituminoso e i risultati dei test sono stati riassunti. Attraverso questi dati di laboratorio, i parametri dei modelli della Master Curve, del danno a fatica e dell’accumulo di deformazioni di taglio usati nella procedura Incrementale – Ricorsiva del CalME sono stati valutati. Infine, nel Capitolo IV, sono stati presentati i risultati delle simulazioni di pavimentazioni stradali con diversi strati superficiali. Per ogni pavimentazione sono stati analizzati la fessurazione superficiale complessiva, le deformazioni permanenti complessive, il danno a fatica e la profondità delle deformazioni in ognuno degli stati legati.

Caratterizzazione avanzata in laboratorio di materie prime secondarie rigenerate o stabilizzate con emulsione di bitume e leganti cementizi

Il recupero dei materiali di scarto è un aspetto di grande attualità in campo stradale, così come negli altri ambiti dell’ingegneria civile. L’attenzione della ricerca e degli esperti del settore è rivolta all’affinamento di tecniche di riciclaggio che riducano l’impatto ambientale senza compromettere le prestazioni meccaniche finali. Tali indagini cercano di far corrispondere le necessità di smaltimento dei rifiuti con quelle dell’industria infrastrutturale, legate al reperimento di materiali da costruzione tecnicamente idonei ed economicamente vantaggiosi. Attualmente sono già diversi i tipi di prodotti rigenerati e riutilizzati nella realizzazione delle pavimentazioni stradali e numerosi sono anche quelli di nuova introduzione in fase di sperimentazione. In particolare, accanto ai materiali derivanti dalle operazioni di recupero della rete viaria, è opportuno considerare anche quelli provenienti dall’esercizio delle attività di trasporto, il quale comporta ogni anno il raggiungimento della fine della vita utile per centinaia di migliaia di tonnellate di pneumatici di gomma. L’obiettivo della presente analisi sperimentale è quello di fornire indicazioni e informazioni in merito alla tecnica di riciclaggio a freddo con emulsione bituminosa e cemento, valutando la possibilità di applicazione di tale metodologia in combinazione con il polverino di gomma, ottenuto dal recupero degli pneumatici fuori uso (PFU). La ricerca si distingue per una duplice valenza: la prima è quella di promuovere ulteriormente la tecnica di riciclaggio a freddo, che si sta imponendo per i suoi numerosi vantaggi economici ed ambientali, legati soprattutto alla temperatura d’esercizio; la seconda è quella di sperimentare l’utilizzo del polverino di gomma, nelle due forme di granulazione tradizionale e criogenica, additivato a miscele costituite interamente da materiale proveniente da scarifica di pavimentazioni esistenti e stabilizzate con diverse percentuali di emulsione di bitume e di legante cementizio.