Recycling of nutrients with application of organic waste in degraded pasture

The utilization of organic wastes represents an alternative to recover degraded pasture. The experiment aimed to assess the changes caused by the provision of different organic waste (poultry litter, turkey litter and pig manure) in a medium-textured Oxisol in Brazilian Savanna under degraded pasture. It was applied different doses of waste compared to the use of mineral fertilizers and organic mineral and evaluated the effect on soil parameters (pH, organic matter, phosphorus and potassium) and leaf of Brachiariadecumbens (crude protein, phosphorus and dry mass production). It was observed that application of organic waste did not increase the level of soil organic matter and pH in the surface layer, and the application of turkey litter caused acidification at depths of 0.20-0.40 m and 0.40-0.60 m. There was an increase in P and K in the soil with the application of poultry litter and swine manure. All organic wastes increased the productivity of dry matter and crude protein and phosphorus. The recycling of nutrients via the application of organic waste allows efficiency of most parameters similar to those observed with the use of mineral sources, contributing to improving the nutritional status of soil-plantsystem.

Growth and mineral nutrition Of Ipomoea quamoclit

A greenhouse experiment was carried out from November 2006 to April 2007 at FCAV/UNESP, Brazil, aiming to study the dry mass production and the accumulation and distribution of macronutrients in Ipomoea quamoclit, an important weed for annual and perennial crops in Brazil. The plants were grown in seven liter pots with sand substrate, daily irrigated with Hoagland & Arnon nutrient solution. The experimental design was completely randomized with four replicates. The treatments corresponded to evaluation times at 14 day intervals, beginning 21 days after emergence (DAE). In each evaluation, the plants of four pots were analyzed in function of dry mass production and macronutrient content. I. quamoclit had a small dry mass and macronutrient accumulation at the beginning of the experimental stage, increasing after 77 DAE and reaching the maximum theoretical value at 146, 143, 140, 149, 142, 153, and 124 DAE, for dry mass, N, P, K, Ca, Mg, and S, respectively. K and N were the macronutrients most accumulated by I. quamoclit plants.

Effect of dose and application site on quinclorac absorption by barnyardgrass biotypes

This work aimed to evaluate the uptake and translocation of quinclorac in function of application sites (shoot or roots) by Echinochloa crusgalli biotypes resistant and susceptible to this herbicide. The treatments consisted of quinclorac doses (0; 0.5; 1; 2; 4; 16 and 64 ppm), applied on the shoot or roots of seedlings of barnyardgrass biotypes. The experimental units consisted of plastic cups containing 250 cm³ of sand. The treatments were applied 10 days after emergence, when barnyardgrass plants reached a 2- to 3- leaf growth stage. The barnyardgrass biotypes were irrigated with nutritive solution weekly and maintained for 40 days after emergence, when length, fresh and dry matter of shoot and roots were evaluated. Variance analysis was carried out using the F test at 5% probability, and in case of significance, a non-linear regression analysis was also carried out using a three-parameter logistic model. In the susceptible biotype, quinclorac was more absorbed by the roots than by the shoot. Comparing dry mass production of the different plant parts of the susceptible biotype per application site, it was verified that quinclorac action is higher when applied to the plant roots. However, for the resistant biotype, it was not possible to determine the dose causing 50% reduction in dry mass accumulation (GR50) and in the resistance index (RI) between both biotypes, due to its high resistance to quinclorac (128 times the recommended dosage). The results showed that quinclorac resistance by the evaluated biotype is not due to differences in the absorption site, strongly suggesting that the resistance acquired by the biotype may result from alteration in the target site.

Effect of plant regulators on growth and flowering of 'Meyer' zoysiagrass

This trial aimed to evaluate the effect of sequential applications of different plant regulators over growth and flower rachis emission of 'Meyer' zoysiagrass (Zoysia japonica). The study was conducted on 15-month old green turfgrass under a randomized complete block design with four replications. The following plant regulator and doses were tested: trinexapac-ethyl (113+113, 226+113, 226+226, 452+113, 452+226, 452+452, 678+339 e 904+452 g a.i./ha-1), prohexadione-calcium (100+100 e 200+200 g a.i. ha-1) and bispyribac-sodium (40+40 e 60+60 g a.i. ha-1), as well as an untreated control. The turfgrass was mowed again at 3.0 cm aboveground and the second plant regulator was applied when 'Meyer' zoysiagrass was between 5.0 and 6.0 cm high. The effect of the treatments was visually rated for visual injury, plant height, height and number of flower rachis, and total dry mass production of clippings. Only bispyribac-sodium had visual symptoms of injury on 'Meyer' zoysiagrass, and no intoxication was observed at 28 days after the second application (DAAB). The sequential applications of trinexapac-ethyl, prohexadione-calcium and bispyribac-sodium reduced by more than 80% the total clipping dry mass produced by 'Meyer' zoysiagrass. All the plant regulators tested also showed promising results in reducing the height and emission of rachis, especially when trinexapac-ethyl was applied at the doses 452+452, 678+339 and 904+452 g a.i. ha-1. 'Meyer' zoysiagrass turfgrass can be handled with the sequential application of a plant regulator, which reduces the need for mowing over a period up to 110 days after the application of the second plant regulator, and it also avoids deleterious visual effects over turfgrass.

European luxury brands made in China: the effect of low-cost country manufacturing on brand image and purchase decisions

European luxury brands have an image of manufacturing their products in the same country where the brands originate. However, in the past years many luxury brands have shifted their manufacturing to countries outside Europe. China is now a common manufacturing country for European luxury brands despite the country’s poor image as a manufacturer. Chinese manufacturing is often associated with bad quality, bad labour conditions, mass production, and counterfeits. The image of China does not quite match the image luxury brands enjoy including characteristics such as high end quality, craftsmanship, details, design, or premium price. A negatively perceived country-of-manufacture may have an effect on a brand’s image and consumers’ purchase decisions. This thesis is focused on European luxury brands manufacturing in China, and how this effects the brand image and purchase decisions among luxury consumers. The empirical part of this thesis is based on focus group research, which is a popular method in the field of qualitative research. The main focus group is female luxury consumers in Finland. This main group has been divided into three categories: 1) the university students, 2) the young career women, 3) the experienced luxury consumers. This categorization has been done based on their different stages in luxury consumption. All in all, the empirical research consisted of 11 interviews and 29 participants. The main contribution of this thesis was that there is a difference between the opinions of the younger groups (university students and young career women) and the experienced luxury consumers when discussing the effect of country-of-manufacture on brand image and purchase decisions of luxury brands. The younger participants thought that manufacturing luxury products in China might affect the brand image, but their purchase decisions would not be that much affected by the country-of-origin. The experienced luxury consumers had quite a different view on the country-of-origin of luxury brands – they found it an important decisive factor prior making purchases. The majority of experienced luxury consumers would not buy luxury products made in China, and they would always check where these products are made in.

Modulaarinen arkkitehtuuri tuoteperheen kehittämisessä

Modulaarisen tuotteen kehittäminen tehostaa yrityksen kilpailukykyä ja helpottaa asiakkaiden tarpeiden tyydyttämistä. Tuoteperheen edut verrattaessa massatuotantoon ovat laajempi tuotevalikoima sekä parempi tuotettavuus massaräätälöintiin verrattuna. Eri tuotevaihtoehtoja ja moduuleja on mahdollista kehittää rinnakkain. Moduloitava tuoteperhe helpottaa yrityksen eri vaiheita aina tuotteen suunnittelusta huoltotoimenpiteisiin ja lopulta tuotteen purkamiseen. Asiakkaille tärkeitä hyötyjä moduloinnin osalta ovat tuotteiden parempi laatu ja huollettavuus. Täysin uuden modulaarisen tuoteperheen kehittäminen vaatii runsaasti resursseja suunnitteluosastolla. Modulaarisessa tuotteessa suunnittelutyö voidaan kohdistaa vain tietyn moduulin kohdalle ja suunnitteluaikoja saadaan täten lyhennettyä. Tässä kandidaatintyössä tutkittiin, miten hitsausautomaatiosovelluksissa modulaarisuus on toteutettu sekä pohditaan kehityskohteita, koska hitsausautomaatiosovelluksia tuotetaan runsaasti asiakasräätälöintinä. Tarkasteltavana tuoteperheenä oli robottihitsausportaalit ja hitsaustornit.

Hydrogen Sensor Application of Anodic Titanium Oxide Nanostructures

Hydrogen (H2) fuel cells have been considered a promising renewable energy source. The recent growth of H2 economy has required highly sensitive, micro-sized and cost-effective H2 sensor for monitoring concentrations and alerting to leakages due to the flammability and explosiveness of H2 Titanium dioxide (TiO2) made by electrochemical anodic oxidation has shown great potential as a H2 sensing material. The aim of this thesis is to develop highly sensitive H2 sensor using anodized TiO2. The sensor enables mass production and integration with microelectronics by preparing the oxide layer on suitable substrate. Morphology, elemental composition, crystal phase, electrical properties and H2 sensing properties of TiO2 nanostructures prepared on Ti foil, Si and SiO2/Si substrates were characterized. Initially, vertically oriented TiO2 nanotubes as the sensing material were obtained by anodizing Ti foil. The morphological properties of tubes could be tailored by varying the applied voltages of the anodization. The transparent oxide layer creates an interference color phenomena with white light illumination on the oxide surface. This coloration effect can be used to predict the morphological properties of the TiO2 nanostructures. The crystal phase transition from amorphous to anatase or rutile, or the mixture of anatase and rutile was observed with varying heat treatment temperatures. However, the H2 sensing properties of TiO2 nanotubes at room temperature were insufficient. H2 sensors using TiO2 nanostructures formed on Si and SiO2/Si substrates were demonstrated. In both cases, a Ti layer deposited on the substrates by a DC magnetron sputtering method was successfully anodized. A mesoporous TiO2 layer obtained on Si by anodization in an aqueous electrolyte at 5°C showed diode behavior, which was influenced by the work function difference of Pt metal electrodes and the oxide layer. The sensor enabled the detection of H2 (20-1000 ppm) at low operating temperatures (50–140°C) in ambient air. A Pd decorated tubular TiO2 layer was prepared on metal electrodes patterned SiO2/Si wafer by anodization in an organic electrolyte at 5°C. The sensor showed significantly enhanced H2 sensing properties, and detected hydrogen in the range of a few ppm with fast response/recovery time. The metal electrodes placed under the oxide layer also enhanced the mechanical tolerance of the sensor. The concept of TiO2 nanostructures on alternative substrates could be a prospect for microelectronic applications and mass production of gas sensors. The gas sensor properties can be further improved by modifying material morphologies and decorating it with catalytic materials.

Asuntorakentamisen vakioidut tekniset ratkaisut rakennettavuuden ja kustannustehokkuuden varmistamiseksi suunnittelunohjauksessa

Rakennushankkeen suunnitteluvaiheen ratkaisut määrittävät merkittävästi hankkeen laatua, aikataulutusta ja kustannustasoa. Tutkimuksen tavoitteena oli selvittää teknisten suunnittelualustojen ja vakioinnin käytön nykytilaa sekä kustannusvaikutuksia kohdeyrityksessä. Kirjallisuustutkimuksessa suunnittelualustat nähtiin työkaluna vakioinnin lisäämiseen suunnitteluprosessissa ja hyvänä keinona suunnittelijoiden ohjaamiseksi. Työ on tutkimusmenetelmiltään laadullinen tapaustutkimus, jossa teknisten ratkaisuiden vakiointipotentiaalia ja kustannustehokkuutta tutkittiin kolmessa erityyppisessä rakenneratkaisussa. Kohdeyrityksen kustannustiedon ja asiantuntijahaastattelujen avulla vertaillut rakenteet oli ilmastointikonehuone, kylpyhuone ja parveke-elementti. Tutkimuksen keskeisissä tuloksissa suunnittelualustan ratkaisuiden käyttö kohdeyrityksessä on varsin säännönmukaista ja valvottua alustan käytön integroituessa osaksi suunnitteluprosessia. Vakioinnin ja esivalmistusasteen lisääminen tarjoaa potentiaalia parantaa rakennettavuutta ja laatua. Vakioinnin mahdollistama sarjavalmistuksen tehokkaampi hyödyntäminen ja vakioinnin volyymiedut ovat potentiaalinen keino alentaa yksikkökustannuksia. Vakioinnin ja esivalmistuksen aikatauluetujen kustannusvaikutus on merkittävä tuotannon aikasidonnaisten kustannusten pienentyessä ja pääoman käytön tehostuessa.

Pulssitettu laserablaatio mikrofluidisten kanavistojen sarjatuotantomenetelmänä

Puolijohteiden yleistyttyä vuodesta 1948 alkaen, ovat elektroniset laitteet pienentyneet jatkuvasti tehojen kuitenkin kasvaessa. Kasvaneet tehotiheydet kuitenkin vaikeuttavat laitesuunnittelua, sillä puoljohdekomponenttien suorituskyvylle ja eliniälle on oleellista lämpötilojen ja lämpötilavaihteluiden minimointi. Perinteisen ilmajäähdytyksen lähestyessä rajojaan niin kokonaistehon kuin järkevän energiatehokkuudenkin suhteen, on parhaaksi seuraavaksi teknologiaksi ennustettu kaksifaasijäähdytystä, jonka suorituskyky ja energiatehokkuus ovat vaaditulla tasolla. Kaksifaasijäähdytyksen optimaaliselle toiminnalle tärkeää on hyvin suunniteltu ja tarkasti valmistettu lämmönsiirtopinta, jota kutsutaan mikrokanavistoksi. Pulssitettu laserkaiverrus on edistynyt valmistustekniikka, jonka tarkkuus ja luotettavuus sopisivat mikrokanavistojen valmistamiseen. Laserkaiverruksella saavutettavat lopputulokset vaihtelevat kuitenkin materiaalista riippuen ja kupari – jota käytetään yleisesti lämmönjohteena – on eräs huonoimmin lasertyöstöön reagoivista materiaaleista ja siksi on oleellista selvittää laser-kaiverruksen toimivuutta kuparisten mikrokanavistojen valmistuksessa. Pulssitetun laser-kaiverruksen eri variaatioista nanosekunti-luokan pulssinpituuksilla toimivat laitteet ovat jatkuvan tuotannon kannalta paras vaihtoehto niiden hyvän tuottavuuden, saatavuuden sekä kohtuullisen alkuinvestoinnin vuoksi. Käytännön kaiverruskokeiden perusteella selvisi, että menetelmä on laatunsa ja tarkkuutensa puolesta sopiva varsinaiseen tuotantoon. Kaiverruksen tehokkuus kuparia työstettäessä on kuitenkin ennakoituakin heikompi ja niin valmistus- kuin suunnitelu-prosessikin vaativat vielä jatkotutkimusta ja -kehitystä.

Applying 3D modelling technology to traditional craftwork : rapid prototyping in artisanal jewellery making and its impact on the perceived value of jewellery

Depuis la révolution industrielle, l’évolution de la technologie bouleverse le monde de la fabrication. Aujourd'hui, de nouvelles technologies telles que le prototypage rapide font une percée dans des domaines comme celui de la fabrication de bijoux, appartenant jadis à l'artisanat et en bouscule les traditions par l'introduction de méthodes plus rapides et plus faciles. Cette recherche vise à répondre aux deux questions suivantes : - ‘En quoi le prototypage rapide influence-t-il la pratique de fabrication de bijoux?’ - ‘En quoi influence-t-il de potentiels acheteurs dans leur appréciation du bijou?’ L' approche consiste en une collecte de données faite au cours de trois entretiens avec différents bijoutiers et une rencontre de deux groupes de discussion composés de consommateurs potentiels. Les résultats ont révélé l’utilité du prototypage rapide pour surmonter un certain nombre d'obstacles inhérents au fait-main, tel que dans sa géométrie, sa commercialisation, et sa finesse de détails. Cependant, il se crée une distance entre la main du bijoutier et l'objet, changeant ainsi la nature de la pratique. Cette technologie est perçue comme un moyen moins authentique car la machine rappelle la production de masse et la possibilité de reproduction en série détruit la notion d’unicité du bijou, en réduisant ainsi sa charge émotionnelle. Cette recherche propose une meilleure compréhension de l'utilisation du prototypage rapide et de ses conséquences dans la fabrication de bijoux. Peut-être ouvrira-t-elle la voie à une recherche visant un meilleur mariage entre cette technique et les méthodes traditionnelles.

Preparation and characterisation of certain II-VI, I-III-VI2 semiconductor thin films and transparent conducting oxides

There is an increasing demand for renewable energies due to the limited availability of fossil and nuclear fuels and due to growing environmental problems. Photovoltaic (PV) energy conversion has the potential to contribute significantly to the electrical energy generation in the future. Currently, the cost for photovoltaic systems is one of the main obstacles preventing production and application on a large scale. The photovoltaic research is now focused on the development of materials that will allow mass production without compromising on the conversion efficiencies. Among important selection criteria of PV material and in particular for thin films, are a suitable band gap, high absorption coefficient and reproducible deposition processes capable of large-volume and low cost production. The chalcopyrite semiconductor thin films such as Copper indium selenide and Copper indium sulphide are the materials that are being intensively investigated for lowering the cost of solar cells. Conversion efficiencies of 19 % have been reported for laboratory scale solar cell based on CuInSe2 and its alloys. The main objective of this thesis work is to optimise the growth conditions of materials suitable for the fabrication of solar cell, employing cost effective techniques. A typical heterojunction thin film solar cell consists of an absorber layer, buffer layer and transparent conducting contacts. The most appropriate techniques have been used for depositing these different layers, viz; chemical bath deposition for the window layer, flash evaporation and two-stage process for the absorber layer, and RF magnetron sputtering for the transparent conducting layer. Low cost experimental setups were fabricated for selenisation and sulphurisation experiments, and the magnetron gun for the RF sputtering was indigenously fabricated. The films thus grown were characterised using different tools. A powder X-ray diffractometer was used to analyse the crystalline nature of the films. The energy dispersive X-ray analysis (EDX) and scanning electron microscopy i (SEM) were used for evaluating the composition and morphology of the films. Optical properties were investigated using the UV-Vis-NIR spectrophotometer by recording the transmission/absorption spectra. The electrical properties were studied using the two probe and four probe electrical measurements. Nature of conductivity of the films was determined by thermoprobe and thermopower measurements. The deposition conditions and the process parameters were optimised based on these characterisations.

Spray Pyrolysed Tin Chalcogenide Thin Films: Optimization of optoelectronic properties of SnS for possible photovoltaic application as an absorber layer

In the early 19th century, industrial revolution was fuelled mainly by the development of machine based manufacturing and the increased use of coal. Later on, the focal point shifted to oil, thanks to the mass-production technology, ease of transport/storage and also the (less) environmental issues in comparison with the coal!! By the dawn of 21st century, due to the depletion of oil reserves and pollution resulting from heavy usage of oil the demand for clean energy was on the rising edge. This ever growing demand has propelled research on photovoltaics which has emerged successful and is currently being looked up to as the only solace for meeting our present day energy requirements. The proven PV technology on commercial scale is based on silicon but the recent boom in the demand for photovoltaic modules has in turn created a shortage in supply of silicon. Also the technology is still not accessible to common man. This has onset the research and development work on moderately efficient, eco-friendly and low cost photovoltaic devices (solar cells). Thin film photovoltaic modules have made a breakthrough entry in the PV market on these grounds. Thin films have the potential to revolutionize the present cost structure of solar cells by eliminating the use of the expensive silicon wafers that alone accounts for above 50% of total module manufacturing cost.Well developed thin film photovoltaic technologies are based on amorphous silicon, CdTe and CuInSe2. However the cell fabrication process using amorphous silicon requires handling of very toxic gases (like phosphene, silane and borane) and costly technologies for cell fabrication. In the case of other materials too, there are difficulties like maintaining stoichiometry (especially in large area films), alleged environmental hazards and high cost of indium. Hence there is an urgent need for the development of materials that are easy to prepare, eco-friendly and available in abundance. The work presented in this thesis is an attempt towards the development of a cost-effective, eco-friendly material for thin film solar cells using simple economically viable technique. Sn-based window and absorber layers deposited using Chemical Spray Pyrolysis (CSP) technique have been chosen for the purpose

Structural, electrical and electrochemical characterization of high frequency magnetron sputtered spinel oxide cathode films for lithium ion battery applications

The main challenges in the deposition of cathode materials in thin film form are the reproduction of stoichiometry close to the bulk material and attaining higher rates of deposition and excellent crystallinity at comparatively lower annealing temperatures. There are several methods available to develop stoichiometric thin film cathode materials including pulsed laser deposition; plasma enhanced chemical vapor deposition, electron beam evaporation, electrostatic spray deposition and RF magnetron sputtering. Among them the most versatile method is the sputtering technique, owing to its suitability for micro-fabricating the thin film batteries directly on chips in any shape or size, and on flexible substrates, with good capacity and cycle life. The main drawback of the conventional sputtering technique using RF frequency of 13.56MHz is its lower rate of deposition, compared to other deposition techniques A typical cathode layer for a thin film battery requires a thickness around one micron. To deposit such thick layers using convention RF sputtering, longer time of deposition is required, since the deposition rate is very low, which is typically 10-20 Å/min. This makes the conventional RF sputtering technique a less viable option for mass production in an economical way. There exists a host of theoretical and experimental evidences and results that higher excitation frequency can be efficiently used to deposit good quality films at higher deposition rates with glow discharge plasma. The effect of frequencies higher than the conventional one (13.56MHz) on the RF magnetron sputtering process has not been subjected to detailed investigations. Attempts have been made in the present work, to sputter deposit spinel oxide cathode films, using high frequency RF excitation source. Most importantly, the major challenge faced by the thin film battery based on the LiMn2O4 cathode material is the poor capacity retention during charge discharge cycling. The major causes for the capacity fading reported in LiMn2O4cathode materials are due to, Jahn-Teller distortion, Mn2+ dissolution into the electrolyte and oxygen loss in cathode material during cycling. The work discussed in this thesis is an attempt on overcoming the above said challenges and developing a high capacity thin film cathode material.

Studies on the evaluation of different sources of proteins, carbohydrates and mineral requirements for juvenile penaeid prawn Penaeus Indicus H. Milne Edwards

In India, directed research on penaeid prawn nutrition was taken up only recently when the aquaculture of prawns gained momentum. One of the important penaeid prawns sought for culture and has great potential is Penagus indiggs, H.Milne Edwards. The Central Marine Fisheries Research Institute working on different aspects of culture of this species over the past one and half decades, has developed a hatchery technology for mass production of its seed and has suggested several improvements on its farming in the grow-out systems. One of the areas of active research in this direction has been on the nutrition of the species with a view to develop suitable feed not only for hatchery production of seed, but also in the field culture. As part of this investigation, the present study, on the evaluation of different protein and carbohydrate sources and mineral requirements for the juvenile E, indicus was taken up and the results obtained are embodied in the thesis

A Study On The Utilisation Of Plastic Wastes In Stabilised Masonry Blocks

At this era of energy crisis and resource depletion, availability of conventional materials throughout the year in quantity and quality, pose a hectic problem for the builders. Adding fuel to the fire, the demand of these materials increases day by day, since the housing and habitat requirements exponentially increase time to time. There is an international concern over this crisis and researchers are reorienting themselves, so as to evolve appropriate masonry units, using locally available cheap materials and technology. The concept of green material and construction has been well conceived in the research so that marginal materials and unskilled labour can be employed for the mass production of building blocks. In this context, considering earth as a sustainable material, there is a growing interest in the use of it, as a modern construction material. Solid waste management is one of the current major environmental concerns in our country. Our country is left with millions of cubic metre of waste plastics. One of the methods to satisfactorily address this solid waste management and the environmental issues is to suitably accommodate the waste in some form (as fibres). Their employability in block making in the form of fibres (plastic fibre- mud blocks) can be investigated through a fundamental research. Also, the review of the existing literature shows that most studies on natural fibres are focussed on cellulose based/ vegetable fibres obtained from renewable plant resources except in very few cases, where animal fibre, plastic fibre and polystyrene fabric were used. At this context, for the plastic fibre-mud blocks to be more widely applicable, a systematic quantification of the relevant physical and mechanical properties of the fibre masonry units is crucial, to enable an objective evaluation of the composite material’s response to actual field condition. This research highlights the salient observations from the detailed investigation of a systematic study on the effect of embedded fibres, made of plastic wastes on the performance of stabilised mud blocks.