Lithography-free micro- and nanostructuring based on conventional plasma etching

In now-a-days semiconductor and MEMS technologies the photolithography is the working horse for fabrication of functional devices. The conventional way (so called Top-Down approach) of microstructuring starts with photolithography, followed by patterning the structures using etching, especially dry etching. The requirements for smaller and hence faster devices lead to decrease of the feature size to the range of several nanometers. However, the production of devices in this scale range needs photolithography equipment, which must overcome the diffraction limit. Therefore, new photolithography techniques have been recently developed, but they are rather expensive and restricted to plane surfaces. Recently a new route has been presented - so-called Bottom-Up approach - where from a single atom or a molecule it is possible to obtain functional devices. This creates new field - Nanotechnology - where one speaks about structures with dimensions 1 - 100 nm, and which has the possibility to replace the conventional photolithography concerning its integral part - the self-assembly. However, this technique requires additional and special equipment and therefore is not yet widely applicable. This work presents a general scheme for the fabrication of silicon and silicon dioxide structures with lateral dimensions of less than 100 nm that avoids high-resolution photolithography processes. For the self-aligned formation of extremely small openings in silicon dioxide layers at in depth sharpened surface structures, the angle dependent etching rate distribution of silicon dioxide against plasma etching with a fluorocarbon gas (CHF3) was exploited. Subsequent anisotropic plasma etching of the silicon substrate material through the perforated silicon dioxide masking layer results in high aspect ratio trenches of approximately the same lateral dimensions. The latter can be reduced and precisely adjusted between 0 and 200 nm by thermal oxidation of the silicon structures owing to the volume expansion of silicon during the oxidation. On the basis of this a technology for the fabrication of SNOM calibration standards is presented. Additionally so-formed trenches were used as a template for CVD deposition of diamond resulting in high aspect ratio diamond knife. A lithography-free method for production of periodic and nonperiodic surface structures using the angular dependence of the etching rate is also presented. It combines the self-assembly of masking particles with the conventional plasma etching techniques known from microelectromechanical system technology. The method is generally applicable to bulk as well as layered materials. In this work, layers of glass spheres of different diameters were assembled on the sample surface forming a mask against plasma etching. Silicon surface structures with periodicity of 500 nm and feature dimensions of 20 nm were produced in this way. Thermal oxidation of the so structured silicon substrate offers the capability to vary the fill factor of the periodic structure owing to the volume expansion during oxidation but also to define silicon dioxide surface structures by selective plasma etching. Similar structures can be simply obtained by structuring silicon dioxide layers on silicon. The method offers a simple route for bridging the Nano- and Microtechnology and moreover, an uncomplicated way for photonic crystal fabrication.

Acumulação de capacidades tecnlógicas e mecanismos subjacentes de aprendizagem relativos a gestão de processos: estudo de caso no setor de serviços bancários no Brasil

Esta dissertação examina o processo de acumulação de capacidades para atividades de operação e de inovação em gestão de processos e os mecanismos subjacentes de aprendizagem em empresas de serviços, especificamente, da indústria bancária, levando-se em consideração as especificidades do contexto de economias emergentes. Durante as últimas décadas duas décadas tem havido numerosos estudos sobre acumulação de capacidades tecnológicas e os mecanismos subjacentes de aprendizagem. Porém, ainda são escassos os estudos empíricos sobre o relacionamento entre essas duas variáveis no contexto de empresas de serviços, especialmente no âmbito da indústria bancária. Essa escassez de estudos dessa natureza é fortemente observada no Brasil. Por isso, buscando ampliar o entendimento sobre a trajetória de acumulação de capacidades tecnológicas e os mecanismos subjacentes de aprendizagem em empresas de serviços, esta dissertação avalia a função tecnológica gestão de processos de uma empresa de serviços bancários, especificamente, a área de tecnologia da informação e comunicação do Banco do Brasil S.A. durante o período de 1982 a 2008. Baseando-se em evidências empíricas qualitativas e quantitativas, de primeira mão, coletadas a partir de um extensivo trabalho de campo, esta dissertação encontrou os seguintes resultados: 1. A área de TIC da empresa acumulou, de 1982 a 2008, capacidades tecnológicas em gestão de processos através de esforços em aquisição e conversão de conhecimentos, de forma que nesse período, iniciando no nível Operacional Básico, onde era capaz somente de executar operações bancárias básicas, atingisse o nível Inovador Intermediário, onde passou a ser capaz de implementar mudanças avançadas na gestão dos processos internos. Além disso, foram encontradas diferenças na velocidade de acumulação das capacidades no período estudado e entre as duas unidades internas da área de TIC, ambas em função dos esforços empreendidos na capacitação em gestão de processos. Cabe ressaltar que a empresa atingiu o 5° nível, em uma escala de 6 níveis, mas não atingiu a fronteira tecnológica. 2. Os processos de aprendizagem foram fontes essenciais para a acumulação de capacidades tecnológicas em gestão de processos. Os processos de aquisição e conversão de conhecimentos possibilitaram que a empresa criasse a base necessária para assimilar conhecimentos mais avançados e complexos. Apesar da importância expressiva dos processos de aprendizagem, percebeu-se que outros fatores internos (mudanças organizacionais) e externos (políticas econômicas) também influenciaram na acumulação de capacidades tecnológicas em gestão de processos. Porém, não foi importante a quantidade desses mecanismos, mas o seu funcionamento ao longo do tempo. Os resultados observados neste estudo permitem concluir que (i) a trajetória de acumulação de capacidades tecnológicas é um processo intencional, contínuo e crescente, decorrente de esforços e investimentos integrados em todas as dimensões das capacidades tecnológicas, (ii) os mecanismos de aprendizagem influenciam a acumulação de capacidades tecnológicas e (iii) a utilização de modelos adaptados à realidade das empresas garante uma análise mais fidedigna do seu comportamento. Esta dissertação contribui para o entendimento da complexidade envolvida no processo de acumulação de capacidades tecnológicas, fator preponderante no diferencial competitivo para empresas de economias emergentes, e especialmente para indústria bancária, onde a competitividade requer processos internos de qualidade elevada que resultem em eficiência operacional e incremento no desempenho econômico-financeiro. E, ainda, ressalta a importância da dimensão organizacional como suporte às demais dimensões de capacidades tecnológicas, através da organização de processos internos e estratégias corporativas. Além disso, sugere aos executivos das empresas do setor bancário brasileiro que a criação intencional de um processo cíclico e contínuo de desenvolvimento dos mecanismos de aprendizagem, considerando suas características-chave, auxilia a empresa em sua trajetória de acumulação de capacidades tecnológicas. Dessa forma, é importante que esses executivos considerem os investimentos em capacitação tecnológica como forma de manter uma posição competitiva sustentável no mercado em que atuam, adequando a estratégia gerencial à empresarial.

Um sistema de visão para navegação robusta de uma plataforma robótica semi-autônoma

Large efforts have been maden by the scientific community on tasks involving locomotion of mobile robots. To execute this kind of task, we must develop to the robot the ability of navigation through the environment in a safe way, that is, without collisions with the objects. In order to perform this, it is necessary to implement strategies that makes possible to detect obstacles. In this work, we deal with this problem by proposing a system that is able to collect sensory information and to estimate the possibility for obstacles to occur in the mobile robot path. Stereo cameras positioned in parallel to each other in a structure coupled to the robot are employed as the main sensory device, making possible the generation of a disparity map. Code optimizations and a strategy for data reduction and abstraction are applied to the images, resulting in a substantial gain in the execution time. This makes possible to the high level decision processes to execute obstacle deviation in real time. This system can be employed in situations where the robot is remotely operated, as well as in situations where it depends only on itself to generate trajectories (the autonomous case)

Caracterização de Efluente Têxtil e Proposta de Tratamento

Textile industry deals with a high diversity of processes and generation of wastewaters with a high content of pollutant material. Before being disposed of in water bodies, a pre-treatment of the effluent is carried out, which is sometimes ineffective. In order to be properly treated, physical and chemical properties of the effluent must be known, as well as the pollutant agents that might be present in it. This has turned out to be a great problem in the textile industry, for there is a variety of processes and the pollutant load is very diversified. The characterization of the effluent allows the identification of most critical points and, as a consequence, the most appropriate treatment procedure to be employed, may be chosen. This study presents the results obtained after characterizing the effluent of a textile industry that comprises knitting, dyeing and apparel sections, processing mainly polyester/cotton articles. In this work, twenty samples of the effluent were collected, and related to the changes in production. From the results, a statistical evaluation was applied, determined in function of the rate of flow. The following properties and pollutants agents were quantitatively analysed: temperature; pH; sulfides; chlorine; alcalinity; chlorides; cianides; phenols; color; COD (Chemical Oxygen Demand); TOC (Total Organic Carbon); oil and grease; total, fixed and volatile solids; dissolved, fixed and volatile solids; suspended, fixed and volatile solids; setteable solids and heavy metals such as cadmium, copper, lead, chromium, tin, iron, zinc and nickel. Analyses were carried out according to ABNT NBR 13402 norm, based upon Standard Methods for the Examination of Water and Wastewater. As a consequence, a global treatment proposal is presented, involving clean production practices as contaminant load reducer, followed by conventional (biological) treatment

Study of RF-excited Diethylene Glycol Dimethyl Ether Plasmas by Mass Spectrometry

This paper deals with the study of the fragmentation process of diethylene glycol dimethyl ether (CH3O(CH2CH2O)(2)CH3) (diglyme here in) molecule in low pressure RF excited plasma discharges. The study was carried out using mass spectrometry. The results showed that for a fixed pressure, the increase of the RF power coupled to the plasma chamber from 1 to 35 W produced a plasma environment much more reactive which increases the population of the ionized species like CH3+ (15 amu), C2H4+ (28 amu), CH3O+ (31 amu), C2H4O+ (44 amu), CH3OCH2CH2+ (59 amu) and CH3OCH2CH2O+ (75 amu). This fact may be attributed to the increase of the electronic temperature that makes predominant the occurrence of inelastic processes that promotes molecular fragmentation. For a fixed value of RF power the increase of pressure from 50 mTorr to 100 mTorr produces the decreasing of the above mentioned chemical species due the lower electronic mean free path. These results suggest that if one wants to keep the monomer's functionality within the plasma deposited films resulting from such kind of discharges one must operate in low power conditions.

Considerations on corrosion and weld repair effects on the fatigue strength of a steel structure critical to the flight-safety

The aim of this study is to analyze the effects of corrosion and successive tungsten inert gas (TIC) welding repairs on the reverse bending fatigue strength of AISI 4130 steel used in components critical to the flight-safety. The tests were performed on hot-rolled steel plate specimens, 1.10 mm and 1.60 mm thick, by means of a SCHENK PWS equipment, with load ratio R = -1, constant amplitude, 30 Hz frequency and room temperature. It was observed that the reverse bending fatigue strength of AISI 4130 steel decreases due to the corrosion and the TIC welding and re-welding processes. (C) 2010 Elsevier Ltd. All rights reserved.

Application times, sources and doses of nitrogen on wheat cultivars under no till in the Cerrado region

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo microestrutural e resistência à corrosão de uma liga de Au soldada a laser, empregada em prótese sobre implantes

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Partitioning of the glucoamylase activity at the cell surfaces in cultures of Saccharomyces

Glucoamylases have been used with alpha-amylases for the industrial conversion of starch into glucose. However, little is known about the properties of this glycosylated protein retained in the cell wall of Saccharomyces as well as its role in the saccharification and fermentation of amylaceous substrates, notably in high cell density processes. In most of the strains assayed, decreases in biomass formation were followed by increases in glucoamylase secretion (expressed as U/mg(biomass) in 1 ml of culture) when glucose was exchanged for starch as carbon source or the growth temperature was raised from 30 to 35 degrees C. Despite the losses in viability, significant increases in the activity of the wall fraction occurred when cultures of thermotolerant yeasts propagated at 30 degrees C or washed cells resuspended in buffer solution were heated to 60 degrees C for 60-80 min prior to amylolytic assays. Thus, intact cells of thermotolerant yeasts can be used as colloidal biocatalysts in starch degradation processes. (C) 2005 Published by Elsevier Ltd.

Metabolic disturbances in male broilers of different strains. 2. Relationship between the thyroid and somatotropic axes with growth rate and mortality

Seven male broiler strains (Arbor Acres, Avian Farms, Cobb-500, Hubbard-Peterson, ISA, Naked Neck, and Ross) were compared for their growth rate, feed efficiency, and mortality due to sudden death and ascites. In addition, weekly plasma levels of thyroid hormones [3,3′,5-triiodothyronine (T3) thyroxine (T4), T3: T4 ratio, growth hormone (GH), and insulin-like growth factor-I (IGF-I)] were determined. The highly productive, commercial strains were very similar in their endocrine profiles but differed markedly from the Naked Neck chickens. Naked Neck chickens were characterized by higher plasma T3 and lower T4 levels at similar ages as well as when compared on the same body weight basis. The present findings support the hypothesis that the slightly hypothyroid state of high productive broilers renders them more sensitive to metabolic disorders. Naked Neck chickens also had higher plasma GH levels than those of their age-matched commercial broilers. The coefficient of variation for GH was highest for Naked Neck chickens, which is indicative for an amplified GH burst amplitude. It may be stated that changes in plasma thyroid hormone concentration in indirect response to selection for low feed conversion and fast growth may be causatively linked to susceptibility for metabolic disturbances such as sudden death syndrome and ascites.

Quality of Latin American and Caribbean industrialization and integration into the global economy

Includes bibliography

Síntese, caracterização e propriedades da matriz sílica-carbono impregnada com níquel obtida pelo método dos precursores poliméricos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência de ciclos térmicos na microestrutura e propriedades mecânicas da junta soldada do aço COS CIVIL 300

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Caracterização microestrutural do metal de solda depositado por arco submerso em chapas de aço-carbono estrutural

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Doses, fontes e épocas de aplicação do nitrogênio em cultivares de trigo sob plantio direto no cerrado

Pós-graduação em Agronomia - FEIS