Highly asymmetric phase diagram of a poly(1,2-octylene oxide)-poly(ethylene oxide) diblock copolymer system comprising a brush-like poly(1,2-octylene oxide) block

The phase diagram of a series of poly(1,2-octylene oxide)-poly(ethylene oxide) (POO-PEO) diblock copolymers is determined by small-angle X-ray scattering. The Flory-Huggins interaction parameter was measured by small-angle neutron scattering. The phase diagram is highly asymmetric due to large conformational asymmetry that results from the hexyl side chains in the POO block. Non-lamellar phases (hexagonal and gyroid) are observed near f(PEO) = 0.5, and the lamellar phase is observed for f(PEO) >= 0.5.

Copolimeros de propileno-etileno com baixos teores de etileno : estrutura, morfologia e propriedades

A estrutura básica predomínante encontrada em todos os copolímeros foi a de longos blocos de polipropileno cristalizáveis, separados por unidades isoladas de etileno, que atuaram como defeitos cristalínos, reduzindo o grau de cristalínidade, além da perfeição e da espessura dos cristais. O gradual aumento do teor de etileno nas amostras origínais, até aproximadamente5 moI % provocou redução progressiva no comprimento dos blocos de propileno em ambas as frações cristalizável e elastomérica. Acima daquela concentração, o etileno mostrou por principal efeito a elevação do teor de borracha de etileno-propileno(EPR), refletíndo-seem pronunciado aumento da resistência ao impacto dos copolímeros, com pouca alteração do comprimento das seqüências propiJênicas nas frações cristaJizáveJe elastomérica. A estrutura e a morfologia da borracha EPR gerada foram analisadas, observando-se sua excepcional dispersão na fase contínua cristalína. Análise das curvas de fusão por DSC, utilizando-se conceitos cínéticos, demonstrou a existência de uma energia de ativação aparente de fusão, associada à introdução de unidades etilênicas nas cadeias, e relacionada ao processo de fusão dos cristais poliméricos. A redução de cristalínidade das amostras e o aumento de mobilidade de cadeia da fase amorfa para teores crescentes de etileno resultaram em redução da rigidez dos copolímeros. Propriedades ópticas, como "haze" e brilho mostraram-se dependentesdo balanço entre o teor de cristais e o teor de borracha. Um balanço global das propriedades analisadas sugere uma composição ótima para aplicações típicas de copolímeros de propileno-etileno aquela com teores de etileno entre 4 e 6 moI % (aproximadamente 3 -4 % em massa).

Linear low density polyethylene (LLDPE) from ethylene using Tp(Ms)NiCl (Tp(Ms) = hydridotris(3-mesitylpyrazol-1-yl)) and CP2ZrCl2 as a tandem catalyst system

Linear low density polyethylene (LLDPE) with different branching contents were prepared from ethylene, without the addition of alpha-olefin comonomer, using a combination of catalyst precursors {Tp(Ms)}NiCl (1) (Tp(Ms) = hydridotris(3-mesitylpyrazol-1-yl)) and Cp2ZrCl2 (2) activated with MAO/TMA (1:1) in toluene at 0degreesC and by varying the nickel loading mole fraction (x(Ni)). The polymerization results showed that the turnover frequencies are strongly dependent on the x(Ni) varying from 6.6 x 10(3) to 32.1 x 10(3) mol[C2H4]/mol[Zr] h. The C-13 NMR spectra of the copolymers showed that the branch contents of the polymers increase as the x(Ni) increase in the medium promoting the production of polymers with a wide range of melting point (T-m) (C) 2004 Elsevier B.V. All rights reserved.

Functional nanostructured catalysts based on the niobates to the dry methane reforming and ethylene homologation reactions

Catalytic activity and selectivity of niobate-based nanostructured materials were investigated. Dry methane reforming (DMR) and ethylene homologation reaction (EHR) were selected as test reactions. KSr 2Nb5O15, Sr2NaNb5O 15 and NaSr2(NiNb4)O15 δ niobate powders were prepared by the high energy ball milling method and calcined in a reductor atmosphere. N2 adsorption isotherms, X-ray diffraction and infrared spectroscopy characterization was performed. Hydrogen pretreated niobates showed from low to moderate catalytic initial activity in DMR's test, nevertheless the materials were deactivated rapidly and the kinetic parameters associated to deactivation were estimated. Otherwise, non-treated catalysts showed a high initial activity in EHR's test and KSr2Nb 5O15 catalyst requires 24 h to the total deactivation with a high selectivity to form propylene. A reaction mechanism to the propylene formation is discussed. © 2012 Elsevier Ltd. All rights reserved.

Self-assembly in aqueous solution of amphiphilic graft copolymers from oxidized carboxymethylcellulose

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Nano- and macroscale structural and mechanical properties of in situ synthesized bacterial cellulose/PEO-b-PPO-b-PEO biocomposites

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Association and Structure of Thermosensitive Comblike Block Copolymers in Aqueous Solutions

The structures and association properties of thermosensitive block copolymers of poly(methoxyoligo( ethylene glycol) norbornenyl esters) in D2O were investigated by small angle neutron scattering (SANS). Each block is a comblike polymer with a polynorbornene (PNB) backbone and oligo ethylene glycol (OEG) side chains (one side chain per NB repeat unit). The chemical formula of the block copolymer is (OEG3NB) 79- (OEG6.6NB) 67, where subscripts represent the degree of polymerization (DP) of OEG and NB in each block. The polymer concentration was fixed at 2.0 wt % and the structural changes were investigated over a temperature range between 25 and 68°C. It was found that at room temperature polymers associate to form micelles with a spherical core formed by the block (OEG3NB) 79 and corona formed by the block (OEG6.6NB) 67 and that the shape of the polymer in the corona could be described by the form factor of rigid cylinders. At elevated temperatures, the aggregation number increased and the micelles became more compact. At temperatures around the cloud point temperature (CPT) T ) 60 °C a correlation peak started to appear and became pronounced at 68 °C due to the formation of a partially ordered structure with a correlation length ∼349 Å.

Compatibilization of polypropylene/poly(3-hydroxybutyrate) blends

Blending polypropylene (PP) with biodegradable poly(3-hydroxybutyrate) (PHB) can be a nice alternative to minimize the disposal problem of PP and the intrinsic brittleness that restricts PHB applications. However, to achieve acceptable engineering properties, the blend needs to be compatibilized because of the immiscibility between PP and PHB. In this work, PP/PHB blends were prepared with different types of copolymers as possible compatibilizers: poly(propylene-g-maleic anhydride) (PPMAH), poly (ethylene-co-methyl acrylate) [P(EMA)], poly(ethylene-co-glycidyl methacrylate) [P(EGMA)], and poly(ethylene-co-methyl acrylate-co-glycidyl methacrylate) [P(EMAGMA)]. The effect of each copolymer on the morphology and mechanical properties of the blends was investigated. The results show that the compatibilizers efficiency decreased in this order: P(EMAGMA) > P(EMA) > P(EGMA) > PP-MAH; we explained this by taking into consideration the affinity degree of the compatibilizers with the PP matrix, the compatibilizers properties, and their ability to provide physical and/or reactive compatibilization with PHB. (C) 2011 Wiley Periodicals, Inc. J Appl Polym Sci 123: 3511-3519, 2012

Oberflächenmodifizierungen von Siliciumoxid und Poly(ethylen-stat-norbornen) durch Blockcopolymere und an Plasmaschichten gebundene Homopolymere

In der vorliegenden Arbeit erfolgten Oberflächenmodifizierungen durch Polymere nach zwei Ansätzen. Dies war zum einen ein Ansatz, bei dem die Oberflächen mit Diblockcopolymeren versehen wurden. Diese bestanden aus einem Ankerblock, der starke Wechselwirkungen mit der Oberfläche zeigt, und einem Bojenblock, der gezielte Eigenschaften trägt. Zum anderen erfolgten Modifizierungen durch auf Plasmaschichten verankerte Homopolymere. Beide Ansätze erfolgten auf zwei Substraten von unterschiedlichen Eigenschaften. Diese waren das Siliciumoxid, für das Modifizierungen durch radikalische in-situ Oberflächenpolymerisation, und das Poly(ethylen-stat-norbornen), für das Modifizierungen durch ex-situ dargestellte Polymere gewählt wurden. Beim ersten Ansatz zur Modifizierung der Siliciumoxidoberfläche ermöglichte ein adsorbierter Poly(e-caprolacton)-Makroinitiator die Oberflächenpolymerisation hin zu oberflächenverankertem Poly(e-caprolacton)-block-poly(alkyl(meth)acrylat). Beim zweiten Ansatz erfolgte die Abscheidung von plasmapolymerisiertem Allylamin, die Immobilisierung des Azoinitiators 4,4’-Azobis(4-cyanopentansäurechlorid) und die nachfolgende Oberflächenpolymerisation von Methylmethacrylat oder Styrol. Beim ersten Modifizierungsansatz der Poly(ethylen-stat-norbornen)-Oberfläche sollte diese mit thermisch interdiffundierten Poly(ethylen-alt-propylen)-block-poly(dimethylsiloxan) versehen werden. Trotz erfolgreicher Synthese wurde gezeigt, daß keine Interdiffusion stattfand. Im zweiten Modifizierungsansatz wurde die Oberfläche mit aus einem Hexamethyldisiloxan/Sauerstoff-Plasma abgeschiedenem reinem Siliciumoxid beschichtet, woran sich die Adsorption von Poly(dimethylsiloxan) anschloß. Damit konnten die hohen Haftreibungskräfte gegenüber Halogenbutylgummi erfolgreich beseitigt werden.

Double-stimulus sensitive (temperature and pH) self-assemblable polymers

The rheological properties of block co-polymers in water solution at different pH have been investigated. The block copolymers are based on different architectures containing poly(ethylene glycol), poly(propylene glycol) and different blocks of polymer that change their hydrophobic/hydrophilic behavior as a function of pH. The polymer chains of the starting material were extended at their functional ends with the pH-sensitive units using ATRP; this mechanism of controlled radical polymerization was chosen because of the need to minimize polydispersity and avoid transfer reactions possibly leading to homopolymeric inpurities. The starting material were modified in order to use them as macroinitiator for ATRP. The kinetic of each ATRP reaction has been investigated, in order to be able to synthesize polymers with different degree of polymerization, stopping the reaction when the desired polymers chain length has been reached. We will use polymer chains with different basicity and degree of polymerization to link any possible effect of their presence to the conditions under which they become hydrophobic. It has been shown that the rate of polymerization changes changing the type of macroinitiator and the type of monomer synthesized. The slowest rate of polymerization is the one with the most hindered monomer synthesized using the macroinitiator with the highest molecular weight. The water solubility of the synthesized polymers changes depending on the pH of the solution and on the structure of the polymers. It has been shown using 1H-NMR that some of the synthesized polymers are capable to self-aggregation in water solution. The self-aggregation and the type of aggregation is influenced from the structure of the polymer and from the pH of the solution. Changing the structure of the polymers and the pH it is possible to obtain different type of aggregates in solution. This aggregates differ for the volume occupied from them, and for their hardness. Rheological measurements have been demonstrated that the synthesized polymers are capable to form gel phases. The gelation temperature changes changing the structure of the aggregates in solution and it is possible to correlate the changing in the gelation temperature with the changing in the structure of the polymer.

Structure and properties of composite polyolefin materials

This thesis is based on three main studies, all dealing with structure-property investigation of semicrystalline polyolefin-based composites. Low density poly(ethylene) (LDPE) and isotactic poly(propylene) (iPP) were chosen as parts of the composites materials and they were investigated either separately (as homoploymers), either in blend systems with the composition LDPE/iPP 80/20 or as filled matrix with layered silicate (montmorillonite). The beneficial influence of adding ethylene-co-propylene polymer of amorphous nature, to low density poly(ethylene)/isotactic poly(propylene) (80/20) blend is demonstrated. This effect is expressed by the major improvement of mechanical properties of ternary blends as examined at a macroscopic size scale by means of tensile measurements. The structure investigation also reveals a clear dependence of the morphology on adding ethylene-copropylene polymer. Both the nature and the content of ethylene-co-propylene polymer affect structure and properties. It is further demonstrated that the extent of improvement in mechanical properties is to be related to the molecular details of the compatibilizer. Combination of high molecular weight and high ethylene content is appropriate for the studied system where the poly(ethylene) plays the role of matrix. A new way to characterize semicrystalline systems by means of Brillouin spectroscopy is presented in this study. By this method based on inelastic light scattering, we were able to measure the high frequency elastic constant (c11) of the two microphases in the case where the spherulites size is exhibit size larger than the size of the probing phonon wavelength. In this considered case, the sample film is inhomogeneous over the relevant length scales and there is an access to the transverse phonon in the crystalline phase yielding the elastic constant c44 as well. Isotactic poly(propylene) is well suited for this type of investigation since its morphology can be tailored through different thermal treatment from the melt. Two distinctly different types of films were used; quenched (low crystallinity) and annealed (high crystallinity). The Brillouin scattering data are discussed with respect to the spherulites size, lamellae thickness, long period, crystallinity degree and well documented by AFM images. The structure and the properties of isotactic poly(propylene) matrix modified by inorganic layered silicate, montmorillonite, are discussed with respect to the clay content. Isotactic poly(propylene)-graft-maleic anhydride was used as compatibilizer. It is clearly demonstrated that the property enhancement is largely due to the ability of layered silicate to exfoliate. The intimate dispersion of the nanometer-thick silicate result from a delicate balance of the content ratio between the isotactic poly(propylene)-graft-maleic anhydride compatibilizer and the inorganic clay.

Synthesis and characterization of temperature- and light-responsive polymers and block copolymers

In summary, thermoresponsive polyacrylamides with various amounts of different photoswitchable side groups, i. e. azobenzene, salicylideneaniline and fulgimide were successfully prepared. As such, in a first step three different chromophores with an amine functionality were synthesized. The synthesis of the stimuli-responsive materials was based on the RAFT polymerization of activated ester acrylates followed by a polymer analogous reaction with different amines. The procedure has been designed to allow the synthesis of well-defined materials with functional groups. All copolymers prepared in this way showed a LCST in aqueous solution. The LCST was in general decreased by increasing the amount of hydrophobic dye incorporated into the thermoresponsive polymer. However, in the case of the fulgimide, the LCST was hardly affected by the chromophore. For azobenzene containing PNIPAM polymers and analogues, higher LCST values were measured after irradiation of the polymer sample solutions with UV-light (Delta LCSTmax = 7.3°C). A reversible light-induced solubility change within a certain temperature range was possible. In contrast to this, irradiated samples of salicylideneaniline containing thermoresponsive copolymers showed an irreversible increase in the LCST (Delta LCSTmax = 13.0°C). Fulgimide chromophores did not influence the LCST of PNIPAM based copolymers after UV-light exposure.rnSimilar to the thermoresponsive polyacrylamides with azobenzene side groups, poly(oligo(ethylene glycol) methyl ether methacrylate) [P(OEGMA)] polymers with azobenzene end groups showed a LCST shift upon UV-irradiation. These polymers were synthesized by RAFT polymerization using a functional chain transfer agent (CTA). For this, PFP-CTA was used as a RAFT-agent for end group functionalization of (thermoresponsive) polymers. In contrast to the statistically arranged copolymers with azobenzene side groups, P(OEGMA) polymers with terminal azobenzene showed a linear increase of the LCST shifts with increasing amount of chromophore (Delta LCSTmax = 4.3°C). Noteworthy, the chemical nature of the end group exhibited a strong influence on the LCST in the case of short thermoresponsive P(OEGMA) polymers.rnThe investigation on temperature- and lightresponsive polymers was transferred onto block copolymers capable to self-assemble into polymeric micelles. Therefore, PEO-b-PNIPAM block copolymers with azobenzene moieties were synthesized successfully. These polymers showed a “smart” behavior in aqueous solution, as the reversible formation and disruption of the micelles could either be controlled by temperature or using light as a stimulus. The usefulness of these materials was demonstrated by encapsulation of a hydrophobic dye in the core of the micelle. Such materials might have a great potential as a model system for several technical or biological applications.rnFinally, double thermoresponsive block copolymers forming micellar structures in a certain temperature range with functional end groups could successfully be synthesized. These “smart materials” based on POEGMA-b-PNIPMAM have been demonstrated to be very promising for a temperature selective immobilization on a protein surface. This might be a suitable concept for further biological applications.rnConcluding, different thermoresponsive copolymers and block copolymers with lightresponsive moieties arranged along the backbone or located at the chain ends were successfully prepared and investigated. By controlling the nature of functional groups and their respective incorporation ratios, the LCST could be dialed in precisely. Further, the LCST of the polymers could be triggered by light. A light-controlled disruption of micellar structures could be shown for functional block copolymers. The importance of end groups of thermoresponsive polymers was demonstrated by a temperature-controlled protein-polymer binding of a terminal biotin-functionalized double thermoresponsive polymer. The synthetic approaches and the material properties presented here should be promising for further research and applications beyond this dissertation.rn

Functional silicones and silicone-containing block copolymers

Polysiloxanes can be synthesized and subsequently modified (i) by the attachment of small molecules that change the properties of the silicone in such a way that it becomes more hydrophilic, but under the premise that this does not go together with a loss of the silicone-specific features. This can be done by adding hydrophilic sidechains to a polysiloxane. Polyethers like poly(ethylene glycol) or hyperbranched polyether-polyols are suitable in this regard. In order to assure that the silicone properties retain, these side groups can be attached to only one part of the polysiloxane backbone, which results in a block copolymer that consists of a common polysiloxane and a second block of the modified structure. (ii) Polysiloxanes can be equipped with functional groups that are capable of initializing polymerization of a different monomer (macroinitiator approach). For example, hydroxyl groups are used to initiate the ring opening polymerization of cyclic esters, or ATRP macroinitiators can be synthesized to add a second block via controlled radical polymerization. Stimuli responsive polymers like poly(oligoethylene glycol methacrylate) (POEGMA) can be added via this route to create “smart” siloxane-containing block copolymers that respond to certain stimuli. rnAn important premise for all synthetic routes is to achieve the targeted structure in a process as simple as possible, because facile availability of the material is crucial with regard to industrial applicability of the invented products. rnConcerning characterization of the synthesized macromolecules, emphasize is put on their (temperature dependent) aggregation behavior, which can be investigated by several microscopic and scattering methods, their behavior at the interface between silicone oils and water and their thermal properties.rnrn

Synthetic routes toward functional block copolymers and bioconjugates via RAFT polymerization

Synthetic Routes toward Functional Block Copolymers and Bioconjugates via RAFT PolymerizationrnSynthesewege für funktionelle Blockcopolymere und Biohybride über RAFT PolymerisationrnDissertation von Dipl.-Chem. Kerstin T. WissrnIm Rahmen dieser Arbeit wurden effiziente Methoden für die Funktionalisierung beider Polymerkettenenden für Polymer- und Bioanbindung von Polymeren entwickelt, die mittels „Reversible Addition-Fragmentation Chain Transfer“ (RAFT) Polymerisation hergestellt wurden. Zu diesem Zweck wurde ein Dithioester-basiertes Kettentransferagens (CTA) mit einer Aktivestereinheit in der R-Gruppe (Pentafluorphenyl-4-phenylthiocarbonylthio-4-cyanovaleriansäureester, kurz PFP-CTA) synthetisiert und seine Anwendung als universelles Werkzeug für die Funktionalisierung der -Endgruppe demonstriert. Zum Einen wurde gezeigt, wie dieser PFP-CTA als Vorläufer für die Synthese anderer funktioneller CTAs durch einfache Aminolyse des Aktivesters genutzt werden kann und somit den synthetischen Aufwand, der üblicherweise mit der Entwicklung neuer CTAs verbunden ist, reduzieren kann. Zum Anderen konnte der PFP-CTA für die Synthese verschiedener Poly(methacrylate) mit enger Molekulargewichtsverteilung und wohl definierter reaktiver -Endgruppe verwendet werden. Dieses Kettenende konnte dann erfolgreich mit verschiedenen primären Aminen wie Propargylamin, 1-Azido-3-aminopropan und Ethylendiamin oder direkt mit den Amin-Endgruppen verschiedener Peptide umgesetzt werden.rnAus der Reaktion des PFP-CTAs mit Propargylamin wurde ein Alkin-CTA erhalten, der sich als effizientes Werkzeug für die RAFT Polymerisation verschiedener Methacrylate erwiesen hat. Der Einbau der Alkin-Funktion am -Kettenende wurde mittels 1H und 13C NMR Spektroskopie sowie MALDI TOF Massenspektroskopie bestätigt. Als Modelreaktion wurde die Kopplung eines solchen alkin-terminierten Poly(di(ethylenglykol)methylethermethacrylates) (PDEGMEMA) mit azid-terminiertem Poly(tert-butylmethacrylat), das mittels Umsetzung einer Aktivester-Endgruppe erhalten wurde, als kupferkatalysierte Azid-Alkin-Cycloaddition (CuAAC) durchgeführt. Die Aufarbeitung des resultierenden Diblockcopolymers durch Fällen ermöglichte die vollständige Abtrennung des Polymerblocks 1, der im Überschuss eingesetzt wurde. Darüber hinaus blieb nur ein sehr kleiner Anteil (< 2 Gew.-%) nicht umgesetzten Polymerblocks 2, was eine erfolgreiche Polymeranbindung und die Effizienz der Endgruppen-Funktionalisierung ausgehend von der Aktivester--Endgruppe belegt.rnDie direkte Reaktion von stimuli-responsiven Polymeren mit Pentafluorphenyl(PFP)ester-Endgruppen, namentlich PDEGMEMA und Poly(oligo(ethylenglykol)methylethermethacrylat), mit kollagen-ähnlichen Peptiden ergab wohl definierte Polymer-Peptid-Diblockcopolymere und Polymer-Peptid-Polymer-Triblockcopolymer unter nahezu quantitativer Umsetzung der Endgruppen. Alle Produkte konnten vollständig von nicht umgesetztem Überschuss des Homopolymers befreit werden. In Analogie zu natürlichem Kollagen und dem nicht funktionalisierten kollagen-ähnlichen Peptid bilden die PDEGMEMA-basierten, entschützten Hybridcopolymere Trimere mit kollagen-ähnlichen Triple-Helices in kalter wässriger Lösung, was mittels Zirkular-Dichroismus-Spektroskopie (CD) nachgewiesen werden konnte. Temperaturabhängige CD-Spektroskopie, Trübungsmessungen und dynamische Lichtstreuung deuteten darauf hin, dass sie bei höheren Temperaturen doppelt stimuli-responsive Überstrukturen bilden, die mindestens zwei konformative Übergänge beim Aufheizen durchlaufen. Einer dieser Übergänge wird durch den hydrophoben Kollaps des Polymerblocks induziert, der andere durch Entfalten der kollagen-ähnlichen Triple-Helices.rnAls Ausweitung dieser synthetischen Strategie wurde homotelecheles PDEGMEMA mit zwei PFP-Esterendgruppen dargestellt, wozu der PFP-CTA für die Funktionalisierung der -Endgruppe und die radikalische Substitution des Dithioesters durch Behandlung mit einem Überschuss eines funktionellen AIBN-Derivates für die Funktionalisierung der -Endgruppe ausgenutzt wurde. Die Umsetzung der beiden reaktiven Kettenenden mit dem N-Terminus eines Peptidblocks ergab ein Peptid-Polymer-Peptid Triblockcopolymer.rnSchließlich konnten die anorganisch-organischen Hybridmaterialien PMSSQ-Poly(2,2-diethoxyethylacrylat) (PMSSQ-PDEEA) und PMSSQ-Poly(1,3-dioxolan-2-ylmethylacrylat) (PMSSQ-PDMA) für die Herstellung robuster, peptid-reaktiver Oberflächen durch Spin Coaten und thermisch induziertes Vernetzen angewendet werden. Nach saurem Entschützen der Acetalgruppen in diesen Filmen konnten die resultierenden Aldehydgruppen durch einfaches Eintauchen in eine Lösung mit einer Auswahl von Aminen und Hydroxylaminen umgesetzt werden, wodurch die Oberflächenhydrophilie modifiziert werden konnte. Darüber hinaus konnten auf Basis der unterschiedlichen Stabilität der zwei hier verglichenen Acetalgruppen Entschützungsprotokolle für die exklusive Entschützung der Diethylacetale in PMSSQ-PDEEA und deren Umsetzung ohne Entschützung der zyklischen Ethylenacetale in PMSSQ-PDMA entwickelt werden, die die Herstellung multifunktioneller Oberflächenbeschichtungen z.B. für die Proteinimmobilisierung ermöglichen.

Poly(lactide): from hyperbranched copolyesters to new block copolymers with functional methacrylates

The prologue of this thesis (Chapter 1.0) gives a general overview on lactone based poly(ester) chemistry with a focus on advanced synthetic strategies for ring-opening polymerization, including the emerging field of organo catalysis. This section is followed by a presentation of the state-of the art regarding the two central fields of the thesis: (i) polyfunctional and branched poly(ester)s in Chapter 1.1 as well as (ii) the development of new poly(ester) based block copolymers with functional methacrylates (Chapter 1.2). Chapter 2 deals with the synthesis of new, non-linear poly(ester) structures. In Chapter 2.1, the synthesis of poly(lactide)-based multiarm stars, prepared via a grafting-from method, is described. The hyperbranched poly(ether)-poly(ol) poly(glycerol) is employed as a hydrophilic core molecule. The resulting star block copolymers exhibit potential as phase transfer agents and can stabilize hydrophilic dyes in a hydrophobic environment. In Chapter 2.2, this approach is expanded to poly(glycolide) multiarm star polymers. The problem of the poor solubility of linear poly(glycolide)s in common organic solvents combined with an improvement of the thermal properties has been approached by the reduction of the total chain length. In Chapter 2.3, the first successful synthesis of hyperbranched poly(lactide)s is presented. The ring-opening, multibranching copolymerization of lactide with the “inimer” 5HDON (a hydroxyl-functional lactone monomer) was carefully examined. Besides a precise molecular characterization involving the determination of the degree of branching, we were able to put forward a reaction model for the formation of branching during polymerization. Several innovative approaches to amphiphilic poly(ester)/poly(methacrylate)-based block copolymers are presented in the third part of the thesis (Chapter 3). Block copolymer build-up especially relies on the combination of ring-opening and living radical polymerization. Atom transfer radical polymerization has been successfully combined with lactide ring-opening, using a “double headed” initiator. This strategy allowed for the realization of poly(lactide)-block-poly(2-hydroxyethyl methacrylate) copolymers, which represent promising materials for tissue engineering scaffolds with anti-fouling properties (Chapter 3.1). The two-step/one-pot approach forgoes the use of protecting groups for HEMA by a careful selection of the reaction conditions. A series of potentially biocompatible and partially biodegradable homo- and block copolymers is described in Chapter 3.2. In order to create a block copolymer with a comparably strong hydrophilic character, a new acetal-protected glycerol monomethacrylate monomer (cis-1,3- benzylidene glycerol methacrylate/BGMA) was designed. The hydrophobic poly(BGMA) could be readily transformed into the hydrophilic and water-soluble poly(iso-glycerol methacrylate) (PIGMA) by mild acidic hydrolysis. Block copolymers of PIGMA and poly(lactide) exhibited interesting spherical aggregates in aqueous environment which could be significantly influenced by variation of the poly(lactide)s stereo-structure. In Chapter 3.3, pH-sensitive poly(ethylene glycol)-b-PBGMA copolymers are described. At slightly acidic pH values (pH 4/37°C), they decompose due to a polarity change of the BGMA block caused by progressing acetal cleavage. This stimuli-responsive behavior renders the system highly attractive for the targeted delivery of anti-cancer drugs. In Chapter 3.4, which was realized in cooperation, the concept of biocompatible, amphiphilic poly(lactide) based polymer drug conjugates, was pursued. This was accomplished in the form of fluorescently labeled poly(HPMA)-b-poly(lactide) copolymers. Fluorescence correlation spectroscopy (FCS) of partially biodegradable block copolymer aggregates exhibited fast cellular uptake by human cervix adenocarcinoma cells without showing toxic effects in the examined concentration range (Chapter 4.1). The current state of further projects which will be pursued in future studies is addressed in Chapter 4. This covers the synthesis of biocompatible star block copolymers (Chapter 4.2) and the development of new methacrylate monomers for biomedical applications (Chapters 4.3 and 4.4). Finally, the further investigation of hydroxyl-functional lactones and carbonates which are promising candidates for the synthesis of new hydrophilic linear or hyperbranched biopolymers, is addressed in Chapter 4.5.