Deposition reactors for solar grade silicon: a comparative thermal analysis of a Siemens reactor and a fluidized bed reactor

Polysilicon production costs contribute approximately to 25-33% of the overall cost of the solar panels and a similar fraction of the total energy invested in their fabrication. Understanding the energy losses and the behaviour of process temperature is an essential requirement as one moves forward to design and build large scale polysilicon manufacturing plants. In this paper we present thermal models for two processes for poly production, viz., the Siemens process using trichlorosilane (TCS) as precursor and the fluid bed process using silane (monosilane, MS).We validate the models with some experimental measurements on prototype laboratory reactors relating the temperature profiles to product quality. A model sensitivity analysis is also performed, and the efects of some key parameters such as reactor wall emissivity, gas distributor temperature, etc., on temperature distribution and product quality are examined. The information presented in this paper is useful for further understanding of the strengths and weaknesses of both deposition technologies, and will help in optimal temperature profiling of these systems aiming at lowering production costs without compromising the solar cell quality.

Thermal shields for heat loss reduction in Siemens-type CVD reactors

The use of thermal shields to reduce radiation heat loss in Siemens-type CVD reactors is analyzed, both theoretically and experimentally. The potential savings from the use of the thermal shields is first explored using a radiation heat model that takes emissivity variations with wavelength into account, which is important for materials that do not behave as grey bodies. The theoretical calculations confirm that materials with lower surface emissivity lead to higher radiation savings. Assuming that radiation heat loss is responsible for around 50% of the total power consumption, a reduction of 32.9% and 15.5% is obtained if thermal shields with constant emissivities of 0.3 and 0.7 are considered, respectively. Experiments considering different thermal shields are conducted in a laboratory CVD reactor, confirming that the real materials do not behave as grey bodies, and proving that significant energy savings in the polysilicon deposition process are obtained. Using silicon as a thermal shield leads to energy savings of between 26.5-28.5%. For wavelength-dependent emissivities, the model shows that there are significant differences in radiation heat loss, of around 25%, when compared to that of constant emissivity. The results of the model highlight the importance of having reliable data on the emissivities within the relevant range of wavelengths, and at deposition temperatures, which remains a pending issue.

Vida útil de revestimento frio e autolimpante.

Considerando aspectos relacionados ao conforto térmico nas edificações e redução da demanda de energia para resfriamento, a utilização de revestimentos frios (que refletem boa parcela da radiação solar recebida e emitem calor) no envelope construtivo pode ser uma alternativa viável para alcançar estas condições. No entanto, a sua durabilidade é o caminho crítico. O presente estudo tem o objetivo de determinar a durabilidade de revestimento multifuncional que reúne as propriedades: fria e autolimpante. Para alcançar esta meta foi formulado um revestimento cimentício monocamada, com e sem a adição de pigmento, ambos com elevada refletância solar e emissividade iniciais. Para manter a refletância ao longo do tempo foi realizada a aplicação de TiO2 anatásio aos revestimentos de duas formas, na primeira as partículas foram adicionadas à matriz cimentícia, enquanto na segunda foram aplicadas superficialmente como pós-tratamento. A exposição à radiação UV proporciona a fotoativação do anatásio que possui capacidade de oxidação da matéria orgânica e alteração do ângulo de contato entre a água e a superfície, facilitando o arraste das sujidades quando esta é molhada tornando-a autolimpante. A manutenção das propriedades frias e a permanência das partículas de TiO2 sobre a superfície foram avaliadas após 6 e 12 meses de exposição natural em estações localizadas nas cidades de Ubatuba, Pirassununga e São Paulo. Após o envelhecimento observou-se a influência determinante das características dos sítios de exposição no comportamento dos materiais. Dentre as formas de aplicação do anatásio verificou-se uma melhora sutil no desempenho dos revestimentos com adição de TiO2 à matriz cimentícia em relação à aplicação superficial do pós-tratamento. O processo de lixiviação observado em ambos os revestimentos expôs as partículas encapsuladas na argamassa com adição de TiO2, enquanto no pós-tratamento houve a remoção da camada superficial de anatásio. Por esse motivo o revestimento com adição apresentou interação com a radiação UV e material a ser degradado por mais tempo. Entretanto os resultados sugeriram que o tempo de exposição foi insuficiente para afirmar este comportamento, pois os resultados são próximos entre si.

Executive summary : implication of RACT for the cutback asphalt industry /

Mode of access: Internet.

Observations of gamma emissions associated with thorium removal from a U²³³ sample /

"U.S. Atomic Energy Commission Contract AT(29-1)-1106."

The total hemispherical emittance of polished and of oxidized alpha plutonium : preliminary report /

The total hemispherical emittance of polished 99.66 w/o plutonium was determined to be 0.37 at 88.7° and 89.0°C. The emittance of polished sample was measured after oxidation in a humid air atmosphere for 24, 66, and 168 hours. Emittances of 0.47, 0.54, and 0.70 were obtained. The apparatus was used to determine a total hemispherical emittance for candle soot of 0.96. Total errors were estimated to be less than ±3%.

Synoptic radio maps of the sun at 3.3mm for the years 1967-1969,

Mode of access: Internet.

The Little Galaxies That Could Reionize the Universe

Thesis (Ph.D.)--University of Washington, 2016-08

The High-Redshift Quasar Luminosity Function from Multi-Epoch Imaging Surveys

Thesis (Ph.D.)--University of Washington, 2016-08

A new, fast and flexible radiative transfer method for Venus general circulation models

We present a new radiation scheme for the Oxford Planetary Unified Model System for Venus, suitable for the solar and thermal bands. This new and fast radiative parameterization uses a different approach in the two main radiative wavelength bands: solar radiation (0.1-5.5 mu m) and thermal radiation (1.7-260 mu m). The solar radiation calculation is based on the delta-Eddington approximation (two-stream-type) with an adding layer method. For the thermal radiation case, a code based on an absorptivity/emissivity formulation is used. The new radiative transfer formulation implemented is intended to be computationally light, to allow its incorporation in 3D global circulation models, but still allowing for the calculation of the effect of atmospheric conditions on radiative fluxes. This will allow us to investigate the dynamical-radiative-microphysical feedbacks. The model flexibility can be also used to explore the uncertainties in the Venus atmosphere such as the optical properties in the deep atmosphere or cloud amount. The results of radiative cooling and heating rates and the global-mean radiative-convective equilibrium temperature profiles for different atmospheric conditions are presented and discussed. This new scheme works in an atmospheric column and can be easily implemented in 3D Venus global circulation models. (C) 2014 Elsevier Ltd. All rights reserved.

Infrared thermography monitoring of the NaCl crystallisation process

In this work, we describe the growth of NaCl crystals by evaporating droplets of aqueous solution while monitoring them with infrared thermography. Over the course of the evaporation experiments, variations in the recorded signal were observed and interpreted as being the result of evaporation and crystallisation. In particular, we observed sharp and transient decreases in the thermosignal during the later stages of high-concentration drop evaporation. The number of such events per experiment, referred to as “pop-cold events”, varied from 1 to over 100 and had durations from 1 to 15 s. These events are interpreted as a consequence from the top-supplied creeping (TSC) of the solution feeding the growth of efflorescence-like crystals. This phenomenon occurred when the solution was no longer macroscopically visible. In this case, efflorescence-like crystals with a spherulite shape grew around previously formed cubic crystals. Other crystal morphologies were also observed but were likely fed by mass diffusion or bottom-supplied creeping (BSC) and were not associated with “pop-cold events”; these morphologies included the cubic crystals at the centre, ring-shaped at the edge of droplets and fan-shaped crystals. After complete evaporation, an analysis of the numbers and sizes of the different types of crystals was performed using image processing. Clear differences in their sizes and distribution were observed in relation to the salt concentration. Infrared thermography permitted a level of quantification that previously was only possible using other techniques. As example, the intermittent efflorescence growth process was clearly observed and measured for the first time using infrared thermography.