963 resultados para Dinoflagellates, calcareous, wall thickness
Resumo:
It has been reported recently that single carbon nanotubes were attached to AFM tips to act as nanotweezers. In order to investigate its stability, a vertical single-walled carbon nanotube (SWCNT) under its own weight is studied in this paper. The lower end of the carbon nanotube is clamped. Firstly the governing dimensionless numbers are derived by dimensional analysis. Then the theoretical analysis based on an elastic column model is carried out. Two ratios, I.e., the ratio of half wall thickness to radius (t=R) and the ratio of gravity to elastic resilience ($\rho$gR=E), and their influences on the ratio of critical length to radius are discussed. It is found that the relationship between the critical ratio of altitude to radius and ratio of half thickness to radius is approximately linear. As the dimensionless number $\rho$gR=E increases, the compressive force per unit length (weight) becomes larger, thus critical ratio of altitude to radius must become smaller to maintain stability. At last the critical length of SWCNT is calculated. The results of this paper will be helpful for the stability design of nanotweezers-like nanostructures.
Resumo:
Current technological advances in fabrication methods have provided pathways to creating architected structural meta-materials similar to those found in natural organisms that are structurally robust and lightweight, such as diatoms. Structural meta-materials are materials with mechanical properties that are determined by material properties at various length scales, which range from the material microstructure (nm) to the macro-scale architecture (μm – mm). It is now possible to exploit material size effect, which emerge at the nanometer length scale, as well as structural effects to tune the material properties and failure mechanisms of small-scale cellular solids, such as nanolattices. This work demonstrates the fabrication and mechanical properties of 3-dimensional hollow nanolattices in both tension and compression. Hollow gold nanolattices loaded in uniaxial compression demonstrate that strength and stiffness vary as a function of geometry and tube wall thickness. Structural effects were explored by increasing the unit cell angle from 30° to 60° while keeping all other parameters constant; material size effects were probed by varying the tube wall thickness, t, from 200nm to 635nm, at a constant relative density and grain size. In-situ uniaxial compression experiments reveal an order-of-magnitude increase in yield stress and modulus in nanolattices with greater lattice angles, and a 150% increase in the yield strength without a concomitant change in modulus in thicker-walled nanolattices for fixed lattice angles. These results imply that independent control of structural and material size effects enables tunability of mechanical properties of 3-dimensional architected meta-materials and highlight the importance of material, geometric, and microstructural effects in small-scale mechanics. This work also explores the flaw tolerance of 3D hollow-tube alumina kagome nanolattices with and without pre-fabricated notches, both in experiment and simulation. Experiments demonstrate that the hollow kagome nanolattices in uniaxial tension always fail at the same load when the ratio of notch length (a) to sample width (w) is no greater than 1/3, with no correlation between failure occurring at or away from the notch. For notches with (a/w) > 1/3, the samples fail at lower peak loads and this is attributed to the increased compliance as fewer unit cells span the un-notched region. Finite element simulations of the kagome tension samples show that the failure is governed by tensile loading for (a/w) < 1/3 but as (a/w) increases, bending begins to play a significant role in the failure. This work explores the flaw sensitivity of hollow alumina kagome nanolattices in tension, using experiments and simulations, and demonstrates that the discrete-continuum duality of architected structural meta-materials gives rise to their flaw insensitivity even when made entirely of intrinsically brittle materials.
Resumo:
Diversas formas de geração de energia vêm sendo desenvolvidas com o objetivo de oferecer alternativas ecologicamente corretas. Neste contexto, a energia eólica vem se destacando na região Nordeste do Brasil, devido ao grande potencial dos ventos da região. As torres, que representam parcela significativa do custo total do sistema, tendem a crescer buscando ventos mais fortes e permitindo assim a utilização de aerogeradores com maior capacidade de geração de energia. Este trabalho tem como objetivo formular um modelo de otimização de torres tubulares de aço, para aerogeradores eólicos. Busca-se minimizar o volume total (custo, indiretamente), tendo como variáveis de projeto as espessuras da parede da torre. São impostas restrições relativas à frequência natural e ao comportamento estrutural (tensão e deslocamento máximo de acordo com recomendações da norma Europeia). A estrutura da torre é modelada com base no Método dos Elementos Finitos e o carregamento atuante na estrutura inclui os pesos da torre, do conjunto de equipamentos instalados no topo (aerogerador), e o efeito estático da ação do vento sobre a torre. Para verificação das tensões, deslocamentos e frequências naturais, foram utilizados elementos finitos de casca disponíveis na biblioteca do programa de análise ANSYS. Os modelos de otimização foram também implementados no modulo de otimização do programa ANSYS (design optimization), que utiliza técnicas matemáticas em um processo iterativo computadorizado até que um projeto considerado ótimo seja alcançado. Nas aplicações foram usados os métodos de aproximação por subproblemas e o método de primeira ordem. Os resultados obtidos revelam que torres para aerogeradores merecem atenção especial, em relação à concepção do projeto estrutural, sendo que seu desempenho deve ser verificado através de metodologias completas que englobem além das análises clássicas (estáticas e dinâmicas), incluam também as análises de otimização.
Resumo:
O exercício contínuo de baixa intensidade é capaz de atenuar a hipertrofia da célula muscular lisa da parede da aorta de ratos espontaneamente hipertensos (SHR), e parece atuar sobre a distribuição de fibras oxitalânicas, elaunínicas e elásticas. As alterações funcionais das grandes artérias relacionadas com a idade, deposição de colágeno e elastina na parede arterial e a elasticidade, são também melhoradas com a atividade física. No presente trabalho objetivamos estudar os efeitos da atividade física aeróbica de baixa intensidade no remodelamento estrutural da artéria aorta em modelo de hipertensão genética de ratos SHR. Através da análise da distribuição das fibras oxitalânicas, elaunínicas e elásticas na aorta dos animais controles e SHR submetidos ou não a atividade física de baixa intensidade. Foram utilizados 32 ratos, sendo 16 ratos SHR machos e 16 ratos normotensos Wistar Kyoto (WKY) machos com 8 semanas de idade. Ratos machos foram alocados em 4 grupos: WKY sedentário (WKY-SED), WKY exercitado (EX-WKY), SHR sedentário (SED-SHR), e SHR exercitado (EX-SHR). Os ratos sedentários foram limitados à atividade na caixa, enquanto que os ratos exercitados foram submetidos a um exercício de 1 h / dia, 5 dias / semana. Esses grupos passaram pelo protocolo de atividade física de 20 semanas e a pressão arterial foi mensurada semanalmente (PA). As aortas foram colhidas e processadas para microscopia de luz, microscopia eletrônica e western blotting. Foram realizadas as colorações orcinol neo-fucsina e resorcina-fucsina de Weigert. No grupo hipertenso, o exercício mantém a PA em um nível relativamente semelhante ao inicio do protocolo, mostrando a capacidade de prevenir o aumento da PA ao longo das 20 semanas. No grupo dos animais hipertensos não tratados, a PA aumenta. A PA aumentou progressivamente nos ratos SED-SHRs atingindo 1894 mmHg, mas o exercício físico impediu este processo. Ao final do experimento a PA nos ratos EX-SHRs foi similar o dos ratos WKY (1184 vs. 1144 mmHg), respectivamente. Observou-se maior expressão de elastina e maior distribuição de fibras oxitalânicas, elaunínicas e elásticas em animais que foram submetidos ao protocolo de exercício físico. A porcentagem de fibras elásticas e oxitalânicas foi menor em SED-SHR comparado com SED-WKY, mas o exercício físico aumentou a porcentagem dessas fibras em ambos os grupos. Através da imuno-histoquímica ultra-estrutural para elastina e fibrilina, os grupos EX-WKY e EX-SHR apresentaram uma marcação mais intensa para elastina e fibrilina. Animais hipertensos que não sofreram o protocolo de exercício físico apresentam espessura da parede da aorta maior que a dos animais que sofreram o exercício. O número de lamelas elásticas, bem como as fibras oxitalânicas e elaunínicas, é maior no grupo EX-SHR, em relação ao SED-SHR. Os grupos exercitados tiveram maior expressão de eNOS que seus respectivos grupos sedentários, e as células endoteliais apresentaram características morfológicas preservadas. A associação da atividade física com modelos de hipertensão genética mostra que o exercício físico tem efeitos benéficos nessa situação, uma vez que atenua a hipertensão e o remodelamento adverso da parede da aorta.
Resumo:
Medir a espessura da parede vesical (EPV) através da ultrassonografia, correlacioná-la com os parâmetros urodinâmicos e avaliar o papel destes parâmetros para lesão do trato urinário superior. Avaliar também o papel das alterações da forma da bexiga nos resultados de injeção de toxina botulínica tipo-A (BTX-A) no detrusor em pacientes com lesão medular traumática (LMT). Trata-se de dois estudos. O primeiro é um estudo transversal de 272 pacientes com LMT submetidos à ultrassonografia renal e de bexiga e estudo urodinâmico. A parede anterior da bexiga foi medida e comparada com os dados urodinâmicos. A cistografia foi realizada em 57 pacientes. O segundo foi um estudo prospectivo avaliando os resultados da injeção de BTX-A no detrusor em 27 pacientes considerando os achados urodinâmicos (pré e pós procedimento) e as deformidades da bexiga (cistografia). A média da EPV foi de 3,94 mm e foi estatisticamente maior em pacientes com hiperatividade detrusora neurogênica associada à dissinergia vesicoesfincteriana (HDN/DVE), em comparação com aqueles sem DVE (p<0,001). Essa média também foi maior em pacientes com complacência < 20 mL/cmH2O, comparada aos pacientes com complacência ≥ 20 mL/cmH2O (p<0,001). A média da pressão detrusora máxima (Pdet Max) foi estatisticamente maior nos pacientes com refluxo vesicoureteral (RVU) em comparação com aqueles sem RVU (100,7 vs 61,2 cmH2O respectivamente, p=0,022). Pacientes com complacência < 20 mL/cmH2O apresentaram prevalência de hidronefrose 4,2 vezes maior, comparada aos pacientes com complacência ≥ 20 mL/cmH2O. Não houve associação estatística entre EPV e hidronefrose ou RVU. Vinte e sete pacientes foram submetidos à injeção de BTX-A no detrusor. A média de tempo de continência urinária foi de 8 meses. Nove pacientes (33,3%) tinham forma vesical alterada e 8 casos (29,6%) tinham divertículos. A capacidade cistométrica máxima, Pdet max, volume reflexo e complacência não apresentaram diferença significativa na presença de divertículos ou alteração da forma. O aumento da EPV está associado à complacência < 20 mL/cmH2O e HDN/DVE em pacientes com LMT. No entanto, não houve relação entre a EPV e hidronefrose ou RVU. Baixa complacência e HDN/DVE são os principais fatores de risco para dano ao trato urinário superior. A presença de divertículos ou alteração da forma vesical não influenciou nos resultados após injeção de BTX-A no detrusor.
Resumo:
We show that tubes of melt cast Bi-2212 used as current leads for LTS magnets can also act as efficient magnetic shields. The magnetic screening properties under an axial DC magnetic field are characterized at several temperatures below the liquid nitrogen temperature (77 K). Two main shielding properties are studied and compared with those of Bi-2223, a material that has been considered in the past for bulk magnetic shields. The first property is related to the maximum magnetic flux density that can be screened, Blim; it is defined as the applied magnetic flux density below which the field attenuation measured at the centre of the shield exceeds 1000. For a cylinder of Bi-2212 with a wall thickness of 5 mm and a large ratio of length over radius, Blim is evaluated to 1 T at T = 10 K. This value largely exceeds the Blim value measured at the same temperature on similar tubes of Bi-2223. The second shielding property that is characterized is the dependence of Blim with respect to variations of the sweep rate of the applied field, dBapp/dt. This dependence is interpreted in terms of the power law E = Ec(J/Jc)^n and allows us to determine the exponent n of this E(J) characteristics for Bi-2212. The characterization of the magnetic field relaxation involves very small values of the electric field. This gives us the opportunity to experimentally determine the E(J) law in an unexplored region of small electric fields. Combining these results with transport and AC shielding measurements, we construct a piecewise E(J) law that spans over 8 orders of magnitude of the electric field.
Resumo:
We demonstrate the fabrication of horizontally aligned carbon nanotube (HA-CNT) networks by spatially programmable folding, which is induced by self-directed liquid infiltration of vertical CNTs. Folding is caused by a capillary buckling instability and is predicted by the elastocapillary buckling height, which scales with the wall thickness as t(3/2). The folding direction is controlled by incorporating folding initiators at the ends of the CNT walls, and the initiators cause a tilt during densification which precedes buckling. By patterning these initiators and specifying the wall geometry, we control the dimensions of HA-CNT patches over 2 orders of magnitude and realize multilayered and multidirectional assemblies. Multidirectional HA-CNT patterns are building blocks for custom design of nanotextured surfaces and flexible circuits.
Resumo:
Deterministic organization of nanostructures into microscale geometries is essential for the development of materials with novel mechanical, optical, and surface properties. We demonstrate scalable fabrication of 3D corrugated carbon nanotube (CNT) microstructures, via an iterative sequence of vertically aligned CNT growth and capillary self-assembly. Vertical microbellows and tilted microcantilevers are created over large areas, and these structures can have thin walls with aspect ratios exceeding 100:1. We show these structures can be used as out-of-plane microsprings with compliance determined by the wall thickness and number of folds. © 2011 American Chemical Society.
Resumo:
Scalable and cost effective patterning of polymer structures and their surface textures is essential to engineer material properties such as liquid wetting and dry adhesion, and to design artificial biological interfaces. Further, fabrication of high-aspect-ratio microstructures often requires controlled deep-etching methods or high-intensity exposure. We demonstrate that carbon nanotube (CNT) composites can be used as master molds for fabrication of high-aspect-ratio polymer microstructures having anisotropic nanoscale textures. The master molds are made by growth of vertically aligned CNT patterns, capillary densification of the CNTs using organic solvents, and capillary-driven infiltration of the CNT structures with SU-8. The composite master structures are then replicated in SU-8 using standard PDMS transfer molding methods. By this process, we fabricated a library of replicas including vertical micro-pillars, honeycomb lattices with sub-micron wall thickness and aspect ratios exceeding 50:1, and microwells with sloped sidewalls. This process enables batch manufacturing of polymer features that capture complex nanoscale shapes and textures, while requiring only optical lithography and conventional thermal processing. © 2011 The Royal Society of Chemistry.
Resumo:
The atomic and electronic structures of saturated and unsaturated GaN nanotubes along the [001] direction with (100) lateral facets are studied using first-principles calculations. Atomic relaxation of nanotubes shows that appreciable distortion occurs in the unsaturated nanotubes. All the nanotubes considered, including saturated and unsaturated ones, exhibit semiconducting, with a direct band gap Surface states arisen from the 3-fold-coordinated N and Ga atoms at the lateral facets exist inside the bulklike band gap. When the nanotubes are saturated with hydrogen, these dangling bond bands are removed from the band gap, but the band gap decreases with increasing the wall thickness of the nanotubes.
Resumo:
A porous InAlAs structure was first obtained by electrochemical etching. Nano-pore arrays were formed when the In0.52Al0.48As membrane was anodized at constant voltages in an HF aqueous solution. These self-assembled structures showed evident blue-shift photoluminescence emissions. While a quantum size effect alone underestimates the blue-shift energy for a sample with a relatively large average pore wall thickness, a novel effect caused by the asymmetric etching is proposed to account for this phenomenon. The results inferred from the x-ray double crystal diffraction are in good agreement with the experimental data.
Resumo:
Well-aligned TiO2/Ti nanotube arrays were synthesized by anodic oxidation of titanium foil in 0.5 wt.% HF in various anoclization voltages. The images of filed emission scanning electron microscopy indicate that the nanotubes structure parameters, such as diameter, wall thickness and density, can be controlled by adjusting the anoclization voltage. The peaks at 25.3 degrees and 48.0 degrees of X-ray diffraction pattern illuminate that the TiO2 nanotube arrays annealed at 500 degrees C are mainly in anatase phase. The filed emission (FE) properties of the samples were investigated. A turn-on electric field 7.8 V/mu m, a field enhancement factors approximately 870 and a highest FE current density 3.4 mA/cm(2) were obtained. The emission current (2.3 mA/cm(2) at 18.8 V/mu m) was quite stable within 480 min. The results show that the FE properties of TiO2/Ti have much relation to the structure parameters.
Resumo:
分析球形水窖空间结构的应力分布情况并进行几何尺寸优化,避免建设者根据经验来确定球形水窖的厚度、构造及混凝土标号,以节省建窖材料,同时防止应力不足而发生破坏。【方法】利用基于ANSYS平台新开发的窖体有限元分析软件,对实际中窖壁厚度为4和11 cm的混凝土薄壳球形水窖进行空间结构应力分析,同时以水窖耗材量最小为目标函数,以许用应力和变形量为约束条件,对其进行几何尺寸优化。【结果】计算得出窖壁厚度为4和11 cm的水窖最大拉应力分别为1 380.00和447.31 kPa,最大压应力分别为5 153.20和1 896.70 kPa;优化出空窖不利工况下容积为20,30和40 m3的球形水窖窖壁最佳厚度,即栗钙土地区分别为0.051,0.061和0.065m,黄土地区分别为0.050,0.059和0.062 m。【结论】经软件优化计算后的球形水窖结构,既能满足强度和刚度的要求,同时也最大限度地节约了材料用量;利用新开发的窖体结构优化分析软件,能够对球形水窖进行空间应力分析与结构优化,可以作为球形水窖设计软件。
Resumo:
The objective of this study was to evaluate degradation behavior and the feasibility of biodegradable polymeric stents in common bile duct (CBD) repair and reconstruction. Various molar ratios of lactide (LA) and glycolide (GA) in poly(L-lactide-co-glycolide) (PLGA) were synthesized and processed into a circular tubing of similar to 10.0 mm outer diameter and a wall thickness of about 2.0 mm.
Resumo:
We produced silver tubes with an outer diameter of 1 mu m, wall thickness of 200 nm, and length of hundreds of micrometers by hydrothermal treatment of aqueous solutions of AgNO3 and hyperbranched polyglycidol (HPG) at 165 degrees C. The surfaces of the silver tubes were chemically modified by HPG, which was confirmed by FTIR of the silver tubes.