Oxidative stability and α-tocopherol retention in soybean oil with lemon seed extract (Citrus limon) under thermoxidation

The synergistic effect of lemon seed extract with tert-butylhydroquinone (TBHQ) in soybean oil subjected to thermoxidation by Rancimat was investigated, and the influence of these antioxidants on α-tocopherol degradation in thermoxidized soybean oil. Control, LSE (2,400 mg/kg Lemon Seed Extract), TBHQ (50 mg/kg), Mixture 1 (LSE + 50 mg/kg TBHQ) and Mixture 2 (LSE + 25 mg/kg TBHQ) were subjected to 180°C for 20 h. Samples were taken at time 0, 5, 10, 15 and 20 h intervals and analysed for oxidative stability and α-tocopherol content. LSE and Mixtures 1 and 2 showed the capacity of retarding lipid oxidation when added to soya oil and also contributed to α-tocopherol retention in oil heated at high temperatures. However, Mixtures 1 and 2 added to the oil presented a greater antioxidant power, consequently proving the antioxidants synergistic effect.

Test results of fault current limiter using YBCO tapes with shunt protection

A Fault Current Limiter (FCL) based on high temperature superconducting elements with four tapes in parallel were designed and tested in 220 V line for a fault current peak between 1 kA to 4 kA. The elements employed second generation (2G) HTS tapes of YBCO coated conductor with stainless steel reinforcement. The tapes were electrically connected in parallel with effective length of 0.4 m per element (16 elements connected in series) constituting a single-phase unit. The FCL performance was evaluated through over-current tests and its recovery characteristics under load current were analyzed using optimized value of the shunt protection. The projected limiting ratio achieved a factor higher than 4 during fault of 5 cycles without degradation. Construction details and further test results will be shown in the paper. © 2010 IOP Publishing Ltd.

Development of ceramic cutting tools for future application on dry machining

Advanced ceramic materials constitute a mature technology with a very broad base of current and potential applications and a growing list of material compositions. Within the advanced ceramics category, silicon nitride based ceramics are wear-resistant, corrosion-resistant and lightweight materials, and are superior to many materials with regard to stability in high-temperature environments. Because of this combination the silicon nitride ceramics have an especially high potential to resolve a wide number of machining problems in the industries. Presently the Si3N4 ceramic cutting tool inserts are developed using additives powders that are pressed and sintered in the form of a cutting tool insert at a temperature of 1850 °C using pressureless sintering. The microstructure of the material was observed and analyzed using XRD, SEM, and the mechanical response of this array microstructure was characterized for hardness Vickers and fracture toughness. The results show that Si3N4/20 wt.% (AlN and Y 2O3) gives the best balance between hardness Vickers and fracture toughness. The Si3N4/15 wt.% (AlN and Y 2O3) composition allows the production of a very fine-grained microstructure with low decreasing of the fracture toughness and increased hardness Vickers. These ceramic cutting tools present adequate characteristics for future application on dry machining. © (2010) Trans Tech Publications.

Geotermobarometria de Granulitos Associados à Supracrustais na Porção Norte do Complexo Guaxupé - Região de Arceburgo - Santa Cruz do Prata, MG

This paper is a contribution for the understanding of the geological evolution of Guaxupé Complex. New data on petrography and mineral chemistry as well as estimates of metamorphic (P-T) conditions in the region of Arceburgo - Santa Cruz do Prata (MG) Brazil, at the southern portion of the Brasília Belt, more specifically at the Guaxupé Complex (Domain) are now presented. The lithotypes are high-grade metamorphic rocks subdivided into two groups: metasediments and granulites (orthoderivates). Chemical analysis of minerals was performed in three steps including core and rim of amphibole, pyroxene, feldspar, biotite, and garnet from samples of the following rock types: enderbites, mafic granulites, charnockites, and alkali feldspar charnockites. Results obtained with geothermobarometric calculations show metamorphic peak around 900°C of T and 10 kbar of P. Enderbites and tonalite granulites (mafic) show the highest values of temperature and pressure, while alkali feldspar charnockites show the lowest probably due to their late generation in relation to mafic rock types (enderbites and mafic tonalite granulite). Chemical mineral analysis in metamorphic parageneses and geothermobarometric calculations indicate that the possible metamorphic peak may be higher than 900°C of temperature and around 10 kbar of pressure, within a isothermal decompression (ITD) regime.

Balance of pH of chicks from eggs injected with ascorbic acid and subjected to thermal stress

This study aimed to verify that chicks from eggs injected with ascorbic acid and subjected to heat stress would have changes in acid-base balance, compared to chicks incubated at thermoneutral without injection of ascorbic acid. The parameters evaluated were blood pressure of carbon dioxide and oxygen, base excess, total carbon dioxide, concentration of sodium, potassium, ionized calcium, bicarbonate and pH of newly hatched male chicks, hatched from eggs injected with acid ascorbic acid (AA) and subjected to heat stress during incubation. The experimental design was completely randomized in factorial scheme 5 (application levels of ascorbic acid) x 2 (incubation temperatures). The data were subjected to analysis of variance using the General Linear Model procedure (GLM) of SAS ®. For the blood pH was observed significant interaction (p <0.05) between treatments with application in eggs and incubation temperatures. For the other parameters were not significant effects (p< 0.05) of AA level and neither temperature of incubation. Analyzing the unfolding of the interaction to pH was observed that chicks from eggs injected with 6% ascorbic acid and subjected to heat stress during incubation had a higher pH value compared with the thermoneutral temperature incubated (p <0.05). Therefore, it is suggested that the incubation of eggs in high temperature (39°C) can alter the metabolic rate of these embryos.

Hybrid nanocomposites containing carboxymethylcellulose and silver nanoparticles

Silver nanoparticles have high temperature stability and low volatility, and at the nanoscale are known to be an effective antifungal and antimicrobial agent. The present investigation involves the synthesis of silver nanoparticle/carboxymethylcellulose nanocomposites. The nanoparticles synthesised in this study had sizes in the range of 100 and 40 nm. The nanocomposites formed by a combination of metallic nanoparticles and carboxymethylcellulose were characterised by contact angle measurements, solubility tests, thermal and mechanical analyses, and morphological images. Improvements in the hydrophobic properties were observed with inclusion of the nanoparticles in the nanocomposites, with the best results occurring after the addition of 40 nm nanoparticles in a carboxymethylcellulose matrix. The silver nanoparticles tend to occupy the empty spaces in the pores of the carboxymethylcellulose matrix, inducing the collapse of these pores and thereby improving the tensile and barrier properties of the film. Copyright © 2013 American Scientific Publishers All rights reserved.

Annual reproductive cycle of males of the flat-faced fruit-eating bat, Artibeus planirostris (Chiroptera: Phyllostomidae)

Artibeus planirostris is an endemic species of Phyllostomid bat from the Neotropical region. Some studies have indicated that it exhibits seasonal bimodal polyestry; however, others postulate that it may be able to produce young at any time during the year. Thus, the aim of this study was to evaluate the annual variations in testicular and epididymal parameters of this species in southeast Brazil and try to understand how the reproduction of this species is regulated in this environment. Sixty mature male specimens, collected between June 2009 and May 2010, were submitted to morphometric and immunohistochemical analysis. Our study showed that A. planirostris presented a continuously active pattern of spermatogenesis throughout the year, presenting spermatozoa inside its cauda epididymis in all months, but with two pronounced peaks of spermatogenic production, one in September and other in February. We propose that the males developed these two peaks in order to produce sufficient sperm for the reproduction in a harem system and to synchronize with the female reproductive cycle, which had a bimodal polyestric pattern. Control of this variation is directly linked to the expression of the androgen receptor (AR) in Sertoli cells and to serum testosterone levels, which appear to synchronize to establish these two peaks. In the months preceding the two peaks, the testis have a higher expression of the AR, which possibly stimulates the increase in PCNA, and drives a gradual increase in the testicular parameters. Taken together the results suggest that if sperm storage happens in this species, it is of short duration. © 2013 Elsevier Inc.

Seasonal effects on semen and testosterone in zebu and taurine bulls

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

O modelo 'hydrotime' pode descrever a resposta de sementes de feijão comum (phaseolus vulgaris l.) à temperatura e potenciais de água reduzidos

Germination parameters of the response to temperature and water potential from four common bean (Phaseolus vulgaris) lines based on thermal-time and hydrotime concepts were estimated to verify to what extent they can predict germination under different thermal and water conditions. The cultivars IPR Uirapuru and IAPAR 81 (drought-tolerant), and Grauna and Carioca (not tolerant) were used. The isothermal assays were performed in a temperature gradient block, and the assays with different osmotic potentials (PEG 6000) were performed in germination chambers. Seeds from drought-tolerant cultivars spent less time to germinate at supra-optimum temperatures than non-tolerant ones, and the cultivar Uirapuru (drought-tolerant) germinated faster in response to reduced Ψ and low temperatures. The parameter Ψb(50) did not discriminate between drought-tolerant and non-tolerant lines at the infraoptimum temperature range, but it can be used to identify drought-tolerant lines at high temperatures. In general, the hydrotime model reproduced the actual germination data relatively well, chiefly at higher temperatures. This study evidenced that the hydrotime model can be used to describe the germination of common bean seeds under reduced water potentials, and as a screening tool for drought-tolerant bean genotypes.

Season of birth as a risk factor for multiple sclerosis in Brazil

Risk factors for development of multiple sclerosis (MS) are still a matter of debate. Latitude gradient, vitamin D deficiency and season of birth are among the most investigated environmental factors associated with the disease. Several international studies suggest that birth in spring is a substantial risk factor for MS. We investigated the season of birth as a potential risk for MS in different geographical regions of Brazil. We conducted a cross-sectional retrospective study with 2257 clinically definite MS patients enrolled in 13 Brazilian MS clinics in the south, southeast, and northeast regions of Brazil. Demographic and clinical data relating to date of birth and clinical features of the disease were collected and analysed, and subsequently compared with birth date among the general Brazilian population. The distribution of date of birth of MS patients showed an increase in spring and a decrease in autumn, with no difference being observed in the other seasons. In conclusion, season of birth is a probable risk factor for MS in most parts of Brazil. These findings may be related to the role that vitamin D plays in MS pathogenesis. © 2013 Elsevier B.V. All rights reserved.

Improvements of plasma immersion ion implantation (PIII) and deposition (PIII&D) processing for materials surface modification

Plasma immersion ion implantation (PIII) process is a three dimensional surface modification method that is quite mature and well known to the surface engineering community nowadays, especially to those working in the field of plasma-materials interaction, aiming at both industrial and academic applications. More recently, deposition methods have been added to PIII, the PIII&D, opening possibilities of broader range of applications of these techniques. So, PIII&D is becoming a routine method of surface modification, with the advantage of pushing up the retained dose levels limited by the sputtering due to ion implantation. Therefore, well adherent, thick, three-dimensional films without stress are possible to be achieved, at relatively low cost, using PIII&D. In this paper, we will discuss about a few PIII and PIII&D experiments that have been performed recently to achieve surface improvements in different materials: 1 - high temperature nitrogen PIII in Ti6Al4V alloy in which a deep nitrogen rich treated layer resulted in surface improvements as increase of hardness, corrosion resistance and resistance to wear of the Ti alloy; 2 - nanostructures in ZnO films, obtained by PIII&D of vaporized & ionized Zn source; 3 - combined implantation and deposition of calcium for biomaterial activity of Ti alloy (PIII&D), allowing the growth of hydroxyapatite in a body solution; 4 - magnetron sputtering deposition of Cr that was enhanced by the glow discharge Ar plasma to allow implantation and deposition of Cr on SAE 1070 steel (PIII&D) resulting in surfaces with high resistance to corrosion; and 5 - implantation of nitrogen by ordinary PIII into this Cr film, which improved resistance to corrosion, while keeping the tribological properties as good as for the SAE 1070 steel surface. © 2012 Elsevier B.V.

Prospects for the use of municipal tree pruning wastes in particleboard production

The purpose of this study was to evaluate the physical and mechanical properties of particleboard made with pruning wastes from Ipê (Tabebuia serratifolia) and Chapéu-de-Sol (Terminalia catappa) trees. Particleboards were prepared with both wood species, using all the material produced by grinding the pruning wastes. The particleboards had dimensions of 45×45 cm, a thickness of approximately 11.5 mm and an average density of 664 kg/m3. A urea-formaldehyde adhesive was used in the proportion of 12% of the dry particle mass. The particleboards were pressed at a temperature of 130 C for 10 mins. The physical and mechanical properties analyzed were density, moisture content, thickness swelling, percentage of lignin and cellulose, modulus of resilience, modulus of elasticity and tensile strength parallel to the grain, accordingly to the standards NBR 14810 and CS 236-66 (1968). The particleboards were considered to be of medium density. The particle size significantly affected the static bending strength and tensile strength parallel to the grain. Ipê presented better results, demonstrating a potential for the production and use of particleboard made from this species. © The Author(s) 2013.

Effect of forced-molting methods and rearing temperatures on the performance and organ biometrics of laying hens

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Properties of individual YBCO layers in a two-layered design for energy-efficient digital data cables

We are developing two-layered Yttrium Barium Copper Oxide (YBCO) thin film structures for energy efficient data links for superconducting electronics and present the results of their property measurements. High temperature superconductors (HTS) are advantageous for the implementation of energy-efficient cables interconnecting low temperature superconductor-based circuits and other cryogenic electronics circuits at higher temperature stages. The advantages of the HTS cables come from their low loss and low dispersion properties, allowing ballistic transfer of low power signals with very high bandwidth, low heat conduction and negligible inter-line crosstalk. The microstrip line cable geometry for typical materials is a two-layered film, in which the two superconducting layers are separated by an insulation layer with a minimized permittivity. We have made a proof of concept design of two YBCO films grown by pulsed laser deposition and then assembled into a sandwich with uniform insulating interlayer of tens of micrometers thick. We report on results obtained from such systems assembled in different ways. Structural and electromagnetic properties have been examined on individual films and on the corresponding sandwich composite. © 2013 IEEE.

Sodium dodecyl sulfate (SDS) effect on the thermal stability of oxy-HbGp: Dynamic light scattering (DLS) and small angle X-ray scattering (SAXS) studies

Glossoscolex paulistus (HbGp) hemoglobin is an oligomeric protein, presenting a quaternary structure constituted by 144 globin and 36 non-globin chains (named linkers) with a total molecular mass of 3.6MDa. SDS effects on the oxy-HbGp thermal stability were studied, by DLS and SAXS, at pH 5.0, 7.0 and 9.0. DLS and SAXS data show that the SDS-oxy-HbGp interactions induce a significant decrease of the protein thermal stability, with the formation of larger aggregates, at pH 5.0. At pH 7.0, oxy-HbGp undergoes complete oligomeric dissociation, with increase of temperature, in the presence of SDS. Besides, oxy-HbGp 3.0mg/mL, pH 7.0, in the presence of SDS, has the oligomeric dissociation process reduced as compared to 0.5mg/mL of protein. At pH 9.0, oxy-HbGp starts to dissociate at 20°C, and the protein is totally dissociated at 50°C. The thermal dissociation kinetic data show that oxy-HbGp oligomeric dissociation at pH 7.0, in the presence of SDS, is strongly dependent on the protein concentration. At 0.5mg/mL of protein, the oligomeric dissociation is complete and fast at 40 and 42°C, with kinetic constants of (2.1±0.2)×10-4 and (5.5±0.4)×10-4s-1, respectively, at 0.6mmol/L SDS. However, at 3.0mg/mL, the oligomeric dissociation process starts at 46°C, and only partial dissociation, accompanied by aggregates formation is observed. Moreover, our data show, for the first time, that, for 3.0mg/mL of protein, the oligomeric dissociation, denaturation and aggregation phenomena occur simultaneously, in the presence of SDS. Our present results on the surfactant-HbGp interactions and the protein thermal unfolding process correspond to a step forward in the understanding of SDS effects. © 2013 Elsevier B.V.