Static pressure and wall shear stress distributions in air flow in a seven wire-wrapped rod bundle

An experimental investigation is performed in a turbulent flow in a seven wire-wrapped rod bundle, mounted in an open air facility. Static pressure distributions are measured on central and peripheral rods. By using a Preston tube, the wall shear stress profiles are experimentally obtained along the perimeter of the rods. The geometric parameters of the test section are P/D=1.20 and H/D=15. The measuring section is located at L/D=40 from the air inlet. It is observed that the dimensionless static pressure and wall shear stress profiles are nearly independent of the Reynolds number and strongly dependent of the wire-spacer position, with abrupt variations of the parameters in the neighborhood of the wires.

Experimental analysis of pressure drop and flow redistribution in axial flows in rod bundles

Fuel elements of PWR type nuclear reactors consist of rod bundles, arranged in a square array, and held by spacer grids. The coolant flows, mainly, axially along the rods. Although such elements are laterally open, experiments are performed in closed type test sections, originating the appearance of subchannels with different geometries. In the present work, utilizing a test section of two bundles of 4x4 pins each, experiments were performed to determine the friction and the grid drag coefficients for the different subchannels and to observe the effect of the grids in the crossflow, in cases of inlet flow maldistribution.

Pressure Drop in Vertical Core-Annular Flow

An experimental apparatus for the study of core annular flows of heavy oil and water at room temperature has been set up and tested at laboratory scale. The test section consists of a 2.75 cm ID galvanized steel pipe. Tap water and a heavy oil (17.6 Pa.s; 963 kg/m³) were used. Pressure drop in a vertical upward test section was accurately measured for oil flow rates in the range 0.297 - 1.045 l/s and water flow rates ranging from 0.063 to 0.315 l/s. The oil-water input ratio was in the range 1-14. The measured pressure drop comprises gravitational and frictional parts. The gravitational pressure drop was expressed in terms of the volumetric fraction of the core, which was determined from a correlation developed by Bannwart (1998b). The existence of an optimum water-oil input ratio for each oil flow rate was observed in the range 0.07 - 0.5. The frictional pressure drop was modeled to account for both hydrodynamic and net buoyancy effects on the core. The model was adjusted to fit our data and shows excellent agreement with data from another source (Bai, 1995).

Onset of Nucleate Boiling and Onset of Fully Developed Subcooled Boiling Using Pressure Transducers Signals Spectral Analysis

The experimental technique used for detection of subcooled boiling through analysis of the fluctuation contained in pressure transducer signals is presented. This work was partly conducted at the Institut für Kerntechnik und zertörungsfreie Prüfverfahren von Hannover (IKPH, Germany) in a thermal-hydraulic circuit with one electrically heated rod with annular geometry test section. Piezoresistive pressure sensors are used for onset of nucleate boiling (ONB) and onset of fully developed boiling (OFDB) detection using spectral analysis/ signal correlation techniques. Experimental results are interpreted by phenomenological analysis of these two points and compared with existing correlation. The results allow us to conclude that this technique is adequate for the detection and monitoring of the ONB and OFDB.

Modeling of high pressure pretreatment process for gold leaching

Investigation of high pressure pretreatment process for gold leaching is the objective of the present master's thesis. The gold ores and concentrates which cannot be easily treated by leaching process are called "refractory". These types of ores or concentrates often have high content of sulfur and arsenic that renders the precious metal inaccessible to the leaching agents. Since the refractory ores in gold manufacturing industry take a considerable share, the pressure oxidation method (autoclave method) is considered as one of the possible ways to overcome the related problems. Mathematical modeling is the main approach in this thesis which was used for investigation of high pressure oxidation process. For this task, available information from literature concerning this phenomenon, including chemistry, mass transfer and kinetics, reaction conditions, applied apparatus and application, was collected and studied. The modeling part includes investigation of pyrite oxidation kinetics in order to create a descriptive mathematical model. The following major steps are completed: creation of process model by using the available knowledge; estimation of unknown parameters and determination of goodness of the fit; study of the reliability of the model and its parameters.

Effect of plant row spacing and herbicide use on weed aboveground biomass and corn grain yield

The use of narrow plant spacing in corn (Zea mays) has been suggested as a technological alternative to obtain grain yield increases, due to a better use of resources. The regular pattern could diminish intraspecific competition while favoring interspecific competition with weeds. The objective of this study was to analyze the effect of corn row spacing on weed aboveground biomass and corn grain yield. Field experiments were conducted during 2002/2003 and 2003/2004 growing seasons. Three corn hybrids with two-row width (0.70 and 0.35 m) were tested. A greater photosynthetic photon flux density (PPFD) interception with a lower weed aboveground dry matter in narrow row arrangement was obtained. Corn grain yield was greater in the narrow row arrangement than in the wide row spacing. This increase in grain yield was related to a better resource use that allows for a reduced interspecific competition. The use of reduced spatial arrangement appeared to be an interesting alternative to increase both the grain yield potential and corn suppressive ability against weeds in corn dryland production systems.

Growth and yield of corn grain and green ear in competition with weeds

Studies on plant growth are interesting because they provide explanations for the factors that influence yield in various crops. The objective of this work was to evaluate growth and yield in corn cultivar AG1051, when in competition with weeds. Cultivar AG 1051 was submitted to two groups of treatments: weed control, and sampling periods for dry biomass evaluation. The weed control treatments consisted of hoeing (two hoeings performed at 20 and 40 days after sowing) and no hoeing. Sampling periods consisted of collecting the above-ground part and roots of corn every fifteen days, until 105 days after sowing (DAS); the first sampling was performed 30 DAS. A completely randomized block design with ten replicates was used. For the characteristics evaluated in a single season, statistical analyses were carried out as a random block experiment. For the characteristics evaluated in several periods, statistical analyses were carried out as random blocks with split-plots (weed control assigned to plots). Fourteen weed species, unevenly distributed throughout the experimental area, were the most important. The growth observed for the above-ground part and root system of corn was 30% smaller in the non-hoed plots, compared to the hoed plots. Lack of weed control increased dry matter of the above-ground part of the weeds and reduced the number of unhusked and husked marketable green ears by 23% and 49%, respectively. Grain yield reduction caused by lack of weed control reached 38%.

Green ear yield and grain yield of maize cultivars in competition with weeds

The reduction in herbicide use is one of the greatest interests for modern agriculture and several alternatives are being investigated with this objective, including the adoption of cultivars that suppress weeds. The objective of this study was to verify if maize cultivars develop differently, in competition with weeds, to produce green ears and grain. Randomized complete block design was used, with split-plots and five replications. Cultivars DKB 390, DKB 466, DKB 350, AG 7000, AG 7575 and Master, were evaluated in the plots, without weeding and two weedings (at 22 and 41 days after sowing) in sub plots. Twenty-one species were identified in the experimental area, the most frequent being Gramineae (Poaceae), Euphorbiaceae, Leguminosae (Fabaceae) and Convolvulaceae species. There was no difference in the dry biomass above-ground part of the weeds in the plots of the evaluated cultivars. The cultivars behaved similarly in treatments with or without hoeing, except for plant height and ear height evaluations. Without hoeing, plant height increased in cultivar DKB 390, while plant height and ear height decreased in cultivar AG 7575. In the other cultivars, these traits did not change under weed control. The presence of weeds decreased the values of all traits employed to assess green corn yield, with the exception of the total number of green ears and grain yield.

Residual activity of herbicides used in soybean agriculture on grain sorghum crop succession

The sorghum is a kind of prominence before the cultures used in succession in the Brazil. However, little information concerning the effects of residual activity of herbicides on the crop in this region are known. The objective of this study was to evaluate the residual activity of herbicides used in weed management in soybeans as well as check their effects on grain sorghum grown in succession. For the field experiment, we used a randomized block design with four replications. Eight herbicide treatments were evaluated: imazaquin (0,161 kg ha-1), diclosulam (0,035 kg ha-1), sulfentrazone (0,600 kg ha-1) and flumioxazin (0,05 kg ha-1) in applications made before emergency and chlorimuron-ethyl (0,015 kg ha-1), imazethapyr (0,060 kg ha-1), imazethapyr (0,100 kg ha-1) and fomesafen (0,250 kg ha-1) applied post-emergence soybean (V3 stadium, 18 DAE), and a control without herbicide application. The grain sorghum (cv. AG-1040) was sown after the harvest of soybeans. The residual activity of these herbicides was determined by bioassay, using the same sorghum cultivars evaluated in the field during the period from 0 to 200days after application the treatments. The sorghum crop showed high sensitivity to residual activity of the herbicide sulfentrazone, diclosulam and imazethapyr dose of 0,100 kg ha-1, even when grown after soybean harvest. Furthermore, the residual activity of sulfentrazone exceeded the range of assessment of bioassay, and more than 200 days.

Pressure filtration characteristics of enzymatically hydrolyzed biomass suspensions

Enzymatic hydrolysis of lignocellulosic polymers is likely to become one of the key technologies enabling industrial production of liquid biofuels and chemicals from lignocellulosic biomass. Certain types of enzymes are able to hydrolyze cellulose and hemicellulose polymers to shorter units and finally to sugar monomers. These monomeric sugars are environmentally acceptable carbon sources for the production of liquid biofuels, such as bioethanol, and other chemicals, such as organic acids. Liquid biofuels in particular have been shown to contribute to the reduction of net emissions of greenhouse gases. The solid residue of enzymatic hydrolysis is composed mainly of lignin and partially degraded fibers, while the liquid phase contains the produced sugars. It is usually necessary to separate these two phases at some point after the hydrolysis stage. Pressure filtration is an efficient technique for this separation. Solid-liquid separation of biomass suspensions is difficult, because biomass solids are able to retain high amounts of water, which cannot be readily liberated by mechanical separation techniques. Most importantly, the filter cakes formed from biomaterials are compressible, which ultimately means that the separation may not be much improved by increasing the filtration pressure. The use of filter aids can therefore facilitate the filtration significantly. On the other hand, the upstream process conditions have a major influence on the filtration process. This thesis investigates how enzymatic hydrolysis and related process conditions affect the filtration properties of a cardboard suspension. The experimental work consists of pressure filtration and characterization of hydrolysates. The study provides novel information about both issues, as the relationship between enzymatic hydrolysis conditions and subsequent filtration properties has so far not been considered in academic studies. The results of the work reveal that the final degree of hydrolysis is an important factor in the filtration stage. High hydrolysis yield generally increases the average specific cake resistance. Mixing during the hydrolysis stage resulted in undefined changes in the physical properties of the solid residue, causing a high filtration resistance when the mixing intensity was high. Theoretical processing of the mixing data led to an interesting observation: the average specific cake resistance was observed to be linearly proportional to the mixer shear stress. Another finding worth attention is that the size distributions of the solids did not change very dramatically during enzymatic hydrolysis. There was an observable size reduction during the first couple of hours, but after that the size reduction was minimal. Similarly, the size distribution of the suspended solids remained almost constant when the hydrolyzed suspension was subjected to intensive mixing. It was also found that the average specific cake resistance was successfully reduced by the use of filter aids. This reduction depended on the method of how the filter aids were applied. In order to obtain high filtration capacity, it is recommended to use the body feed mode, i.e. to mix the filter aid with the slurry prior to filtration. Regarding the quality of the filtrate, precoat filtration was observed to produce a clear filtrate with negligible suspended solids content, while the body feed filtrates were turbid, irrespective of which type of filter aid was used.

Effects of irrigated rice sowing season and imazapyr + imazapic time of application on rice grain yield and red rice management

Irrigated rice sowing season and red rice competition are among the main factors affecting grain yield. The objective of this work was to evaluate the sowing date of irrigated rice and moments of application of the herbicide imazapyr + imazapic to control red rice management and irrigated rice grain yield. Eight experiments were performed at the following dates (09/30, 10/19, 11/08 and 12/01) for the 2010/2011 harvest season and (09/27, 10/17, 11/08 and 12/05) for the 2011/2012 harvest season. The treatments were: application of the herbicide imazapyr + imazapic at doses of 105+35 g ha-1 in pre-emergence (PRE); 52.5+17.5 g ha‑1 in pre-emergence and 52.5+17.5 g ha-1 in post-emergence (PRE + POST); and 105+35 g ha-1 in post- emergence (POST), and a control without application and no weeding. The cultivar Puitá Inta CL was used and a randomized block design with four replicates. A joint analysis of the experiments was carried out. There was less emergence of red rice and higher grain yield of the irrigated rice at the early periods (09/30/10 and 09/27/11), with 10,578 and 8,653 kg ha-1, respectively. At the end of the season (12/01/10 and 12/05/11), there was greater reduction of the red rice seed bank. Sowing at the beginning of the recommended period provided more irrigated rice grain yield. The application of imazapyr + imazapic at a dose of 52.5+17.5 g ha-1 in PRE + 52.5+17.5 g ha-1 POST, and 105+35 g ha-1 only in PRE and POST was effective in the control of red rice.

Estimation of weed dry biomass and grain yield as a function of growth and yield traits under allelopathic weed management in maize

Growing concerns about toxicity and development of resistance against synthetic herbicides have demanded looking for alternative weed management approaches. Allelopathy has gained sufficient support and potential for sustainable weed management. Aqueous extracts of six plant species (sunflower, rice, mulberry, maize, brassica and sorghum) in different combinations alone or in mixture with 75% reduced dose of herbicides were evaluated for two consecutive years under field conditions. A weedy check and S-metolachlor with atrazine (pre emergence) and atrazine alone (post emergence) at recommended rates was included for comparison. Weed dynamics, maize growth indices and yield estimation were done by following standard procedures. All aqueous plant extract combinations suppressed weed growth and biomass. Moreover, the suppressive effect was more pronounced when aqueous plant extracts were supplemented with reduced doses of herbicides. Brassica-sunflower-sorghum combination suppressed weeds by 74-80, 78-70, 65-68% during both years of study that was similar with S-metolachlor along half dose of atrazine and full dose of atrazine alone. Crop growth rate and dry matter accumulation attained peak values of 32.68 and 1,502 g m-2 d-1 for brassica-sunflower-sorghum combination at 60 and 75 days after sowing. Curve fitting regression for growth and yield traits predicted strong positive correlation to grain yield and negative correlation to weed dry biomass under allelopathic weed management in maize crop.

Levels of nutrients and grain yield of maize intercropped with signalgrass (Brachiaria) in different arrangements of plants

Competition between maize and signalgrass can economically cripple the intercropping by the reduced yield of maize and dry matter content of the forage. In seeking to define plant arrangements which make this system more efficient, this research was held with the objective of assessing the effects of interference of densities of signalgrass (Urochloa Brizantha) on nutrition and on maize grain yield. Two field experiments were conducted in a randomized block design with four replications. Treatments were arranged similarly in both experiments, in a 2 x 4 factorial design, the first factor being the dose of Nicosulfuron herbicide applied (0 and 8 g ha-1) and the second factor being the forage seeding rates (0, 2, 4 and 6 kg of seeds per hectare). The interference of signalgrass reduced foliar nitrogen, potassium and phosphorus content in maize plants intercropped with the forage. Higher values of grain yield were observed with the reduction of the spacing and the application of the recommended herbicide underdose (8 g ha-1). It was concluded that, regardless of the seeding density of U. Brizantha, reducing the maize seeding inter-rows spacing, combined with the application of an underdose of Nicosulfuron, caused a positive effect by reducing the initial forage growth, resulting in less interference of Urochloa brizantha on nutrient uptake by the maize plants and grain yield of the crop.

Storage substances in the androgametogenesis and mature pollen grain of Ilex paraguariensis St. Hil. (Aquifoliaceae)

Storage substances such as starch grains, proteins and lipids were studied during the male gametogenesis and in the mature pollen grain of Ilex paraguariensis St. Hil. (Aquifoliaceae). There are two cycles of amylogenesis and amylolyse. The first cycle lasts until the vacuolated stage when the starch is hydrolyzed and amorphous proteins are stored inside the single vacuole. The next cycle begins after mitosis with the formation of the vegetative and generative cells. At this point, the young vegetative cell stores many starch grains that are bigger than in the first cycle. During the maturation of the male gametophyte, the starch is hydrolyzed and it is absent in the mature pollen grain. Small lipid droplets surround the young generative cell after the mitosis of the androspore and are dispersed in the vegetative cytoplasm during its maturity. The relationship between the pollen storage substances and the ontogeny of the layers in the sporoderm, formation of the generative cell, and the male germ unit were discussed.

Two point deterministic model for acquisition of in vitro pollen grain androgenetic capacity based on wheat studies

This article discusses, from the standpoint of cellular biology, the deterministic and indeterministic androgenesis theories. The role of the vacuole and of various types of stresses on deviation of the microspore from normal development and the point where androgenetic competence is acquired are examined. Based on extensive literature review and data on wheat studies from our laboratory, a model for androgenetic capacity of pollen grain is proposed. A two point deterministic model for in vitro androgenesis is our proposal for acquisition of androgenetic potential of the pollen grain: the first switch point would be early meiosis and the second switch point the uninucleate pollen stage, because the elimination of cytoplasmatic sporophytic determinants takes place at those two strategic moments. Any abnormality in this process allowing the maintenance of sporophytic informational molecules results in the absence of establishment of a gametophytic program, allowing the reactivation of the embryogenic process