Audiological and electrophysiological assessment of professional pop/rock musicians

In the present study, we evaluated peripheral and central auditory pathways in professional musicians (with and without hearing loss) compared to non-musicians. The goal was to verify if music exposure could affect auditory pathways as a whole. This is a prospective study that compared the results obtained between three groups (musicians with and without hearing loss and non-musicians). Thirty-two male individuals participated and they were assessed by: Immittance measurements, pure-tone air conduction thresholds at all frequencies from 0.25 to 20 kHz, Transient Evoked Otoacoustic Emissions, Auditory Brainstem Response (ABR), and Cognitive Potential. The musicians showed worse hearing thresholds in both conventional and high frequency audiometry when compared to the non-musicians; the mean amplitude of Transient Evoked Otoacoustic Emissions was smaller in the musicians group, but the mean latencies of Auditory Brainstem Response and Cognitive Potential were diminished in the musicians when compared to the non-musicians. Our findings suggest that the population of musicians is at risk for developing music-induced hearing loss. However, the electrophysiological evaluation showed that latency waves of ABR and P300 were diminished in musicians, which may suggest that the auditory training to which these musicians are exposed acts as a facilitator of the acoustic signal transmission to the cortex.

Invasion of the dinoflagellate Ceratium furcoides (Levander) Langhans 1925 at tropical reservoir and its relation to environmental variables

Dinoflagellates of the genus Ceratium are chiefly marine but there are rare occurrences in freshwater. In this study we analyze the invasion and progressive establishment of Ceratium furcoides, an exotic species, in the Furnas Reservoir. Samples were taken at 36 points in the reservoir, during the months of March, June, September and December, 2007. Measurements of some physical and chemical variables were simultaneously performed at each site. The occurrence of C. furcoides was registered at 20 sites, with densities varying between 0.57 and 28,564,913.0 ind.m-3. Blooms of this species were recorded in points which were classified as mesotrophic, coinciding with the places receiving high amounts of untreated domestic sewage. C. furcoides density was correlated with temperature, nutrients (nitrate and nitrite) and water electric conductivity. The highest density was recorded in June when temperature was low. The presence of Ceratium furcoides in the reservoir apparently has not yet affected the reservoir water quality or other plankton communities. However, if it becomes fully established it could perhaps become a problem in the reservoir or even to spread out to other reservoirs in Rio Grande basin.

Relationship between space distribution of the benthic macroinvertebrates community and trophic state in a Neotropical reservoir (Itupararanga, Brazil)

The purpose of this work was to verify the benthic macroinvertebrates community responses through environmental factors along a headwater tropical reservoir. Samplings were taken with a Van-Veen grab along the reservoir in littoral and profundal regions and in the headwater, next to the dam and the middle of the reservoir. Samples were taken during both wet and dry seasons. Dissolved oxygen concentrations, electric conductivity, temperature and pH near the sediment have been performed in situ, at every sampling station by using a multiprobe and Secchi disc. Total water phosphorus and chlorophyll a concentrations were analyzed to determine the trophic state index. Sediment's organic matter, total phosphorus, nitrogen concentrations and granulometric composition were measured. In order to verify which environmental variables would have more influence over the benthic macroinvertebrates community, a canonical correspondence analysis (CCA) was performed. The total number of recorded taxa was 28. Among them, the family Chironomidae (Diptera) was the richest group (19 taxa). It can be proposed that the benthic macroinvertebrates community may be influenced by environmental conditions such as nutrient and organic matter availability, as well as dissolved oxygen concentration. Macroinvertebrates are adequate bioindicators of water quality due to their sensibility to environmental changes mentioned before. Chironomus sp, Limnodrilus hoffmeisteri and Branchiura sowerbyi comprises a group that can be considered bio-indicators of eutrophic conditions. A second group can be considered as indicator of mesotrophic conditions. The presence of two or more members from that group which comprises Tanytarsini spp, Fissimentum sp, Pelomus sp and Goeldichironomus sp, like predominant taxa, may indicates mesotrophic conditions.

The role of asymmetries in rock-paper-scissors biodiversity models.

The maintenance of biodiversity is a long standing puzzle in ecology. It is a classical result that if the interactions of the species in an ecosystem are chosen in a random way, then complex ecosystems can't sustain themselves, meaning that the structure of the interactions between the species must be a central component on the preservation of biodiversity and on the stability of ecosystems. The rock-paper-scissors model is one of the paradigmatic models that study how biodiversity is maintained. In this model 3 species dominate each other in a cyclic way (mimicking a trophic cycle), that is, rock dominates scissors, that dominates paper, that dominates rock. In the original version of this model, this dominance obeys a 'Z IND 3' symmetry, in the sense that the strength of dominance is always the same. In this work, we break this symmetry, studying the effects of the addition of an asymmetry parameter. In the usual model, in a two dimensional lattice, the species distribute themselves according to spiral patterns, that can be explained by the complex Landau-Guinzburg equation. With the addition of asymmetry, new spatial patterns appear during the transient and the system either ends in a state with spirals, similar to the ones of the original model, or in a state where unstable spatial patterns dominate or in a state where only one species survives (and biodiversity is lost).

Effects of trophic levels (chlorophyll and phosphorous content) in three different water bodies (urban lake, reservoir and aquaculture facility) on gill morphology of Nile tilapia (Oreochromis niloticus)

Histological and ultrastructural analyses of gills were observed in Nile tilapia collected from three different waterbodies in southeast Brazil: an urban lake in a park in the city of São Paulo, a reservoir in a rural city, and a commercial aquaculture facility. These aterbodies were analyzed and classified as hypereutrophic, eutrophic, and supereutrophic, respectively, with 310.00, 94.00, 28.00 of phosphate (PO2_ 4 lg L _1) and 65.49, 24.95, 12.83 of chlorophyll (lg L _1). A significant difference in the histological alterations index (HAI) was observed only in fish from the urban lake, with the presence of cell hypertrophy, hyperplasia, aneurism, and other alterations. When compared to the other groups, a large quantity of rodlet cells was also observed in the urban group. These results demonstrate the correlation of eutrophic states of water with gill morphology. Also discussed is the premise that large amounts of organic material dissolved in water can alter the morphology of the fish gills

Rock of ages

[EN] Granite is emplaced deep in the Earth's crust. It cools and crystallises and is subjected to thermal and magmatic events, and to recurrent stresses. It develops textures or fabrics as well as strain patterns which, as erosion brings the rock mass near the surface, find expression in various fracture sets and systems.

Ecological tools for assessing rock-art conservation in the Côa Valley Archaeological Park (V.N. Foz Côa, Northeast Portugal)

Centro de Investigação em Biodiversidade e Recursos Genéticos da Universidade do Porto. Departamento de Biologia, Faculdade de Ciências da Universidade do Porto. EscolaUniversitaria de Enxeñeria Forestal, Universidade de Vigo

La explotación del acuífero de la Aldea (Gran Canaria) desde el punto de vista de la directiva marco del agua

[ES] El valle de La Aldea, al oeste de Gran Canaria, se dedica a la agricultura intensiva en un clima semi-árido. El agua de riego proviene de aguas superficiales y subterráneas. El acuífero está aislado del resto de la isla por el borde impermeable de la Caldera de Tejeda. El aluvial principal de La Aldea se comporta como un depósito de almacenamiento de agua que se llena y vacía, con un tiempo medio de renovación de aproximadamente 2 años. Las aguas subterráneas muestran una alta salinidad de origen natural, debido a la evapoconcentración de la deposición atmosférica y la interacción agua-roca, y antropogénica debida a los retornos de riego que producen contenidos en nitratos que pueden alcanzar los 700 mg/L. Se ha establecido un modelo conceptual de funcionamiento del acuífero y se han cuantificado los términos del balance de agua. El uso actual del acuífero está en conflicto con los requerimientos de la Directiva Marco del Agua (DMA). Sin embargo, dado que su uso es clave para el desarrollo económico del valle de La Aldea en particular, cabe plantear las excepciones legales específicas previstas en la DMA.

Modelli di scambio termico in pozzo sulla base della caratterizzazione geotermica di un reservoir a bassa entalpia: studio di sensitività sulla efficienza dei sistemi di condizionamento a pompa di calore

Tra i temi di attualità, quello del risparmio energetico è tra i più dibattuti negli ultimi anni; tale tema è strettamente correlato al problema del riscaldamento globale, infatti, mentre sul prossimo esaurimento delle risorse energetiche tradizionali non vi sono ancora certezze assolute, per quanto riguarda l’azione nociva dei gas serra, la Comunità Scientifica Internazionale si ritrova d’accordo su una netta presa di posizione contro l’emissione di tali sostanze, provocata in larga parte dall’utilizzo dei combustibili fossili. In questo contesto, l’Unione Europea sta promuovendo la diffusione di tecnologie che non prevedano l’utilizzo di gas, petrolio o carbone, soprattutto per il settore dell’edilizia, ove una corretta progettazione e l’utilizzo di tecnologie non convenzionali può portare alla riduzione anche dell’80% dei consumi, con conseguente abbattimento delle emissioni. Tra questi interventi innovativi, il più comune e conosciuto è sicuramente quello del solare termico e fotovoltaico; ma ne esistono anche di altri, ancora non molto pubblicizzati in Italia, ma ampiamente conosciuti e utilizzati in altri paesi dell’Unione. Tra questi, vi è il sistema di riscaldamento analizzato in questa tesi: la pompa di calore geotermica. Tale sistema, come verrà spiegato nell’elaborato di laurea, ha indubbi vantaggi economici, energetici ed ambientali, a fronte di una non trascurabile spesa iniziale. Attualmente, nel Nord Italia, si incominciano a vedere impianti di questo tipo, sulla scia del successo riscontrato nei paesi confinanti (in particolare Austria e Svizzera). La progettazione si basa attualmente su modelli statici, sviluppati dall’Università Svizzera del Canton Ticino, per l’utilizzo della pompa di calore nel territorio alpino. Obiettivo della tesi, è la verifica di tali modelli, di cui si è venuto a conoscenza grazie alla collaborazione con l’Università SUPSI, sulle condizioni idrogeologiche della Pianura Padana, soffermandosi su alcuni parametri fondamentali della progettazione di una pompa di calore geotermica, quali la conduttività e la capacità termica volumetrica dei terreni incontrati, la presenza di falde, ed i parametri geometrici del pozzo, al fine di dare una valutazione tecnica ed economica dell’impianto. Tali analisi è stata infatti fino ad ora affrontata in maniera sommaria dai perforatori, che eseguono generalmente sempre lo stesso modello di pozzo geotermico, sulla base degli esempi consolidati di Svizzera e Germania. Alcune misure di temperatura in situ sono state rilevate in collaborazione con la società Geotermia SRL di Mantova, ditta specializzata nella perforazione di pozzi geotermici (tale esperienza è parte centrale dell’estratto “Laboratorio di Tesi Ls”), mentre la parte modellistica della tesi è stata sviluppata in collaborazione con lo studio di progettazione Studio Seta SRL di Faenza, il cui stabile è climatizzato in parte con una pompa di calore geotermica.

Influence of reservoir geometry and conditions on the seismic response of arch dams

[EN]An analysis of the influence that reservoir levels and bottom sediment properties (especially on the degree of saturation) have on the dynamic response of arch dams is caried out. For this purpose, a Boundary Element Model developed by the authors that allows the direct dynamic study of problems that incorporate scalar, viscoelastic and poroelastic media is used.

Modeling hydrothermal system: deriving observables and hydrothermal instability in volcanic and non-volcanic setting

Hydrothermal fluids are a fundamental resource for understanding and monitoring volcanic and non-volcanic systems. This thesis is focused on the study of hydrothermal system through numerical modeling with the geothermal simulator TOUGH2. Several simulations are presented, and geophysical and geochemical observables, arising from fluids circulation, are analyzed in detail throughout the thesis. In a volcanic setting, fluids feeding fumaroles and hot spring may play a key role in the hazard evaluation. The evolution of the fluids circulation is caused by a strong interaction between magmatic and hydrothermal systems. A simultaneous analysis of different geophysical and geochemical observables is a sound approach for interpreting monitored data and to infer a consistent conceptual model. Analyzed observables are ground displacement, gravity changes, electrical conductivity, amount, composition and temperature of the emitted gases at surface, and extent of degassing area. Results highlight the different temporal response of the considered observables, as well as the different radial pattern of variation. However, magnitude, temporal response and radial pattern of these signals depend not only on the evolution of fluid circulation, but a main role is played by the considered rock properties. Numerical simulations highlight differences that arise from the assumption of different permeabilities, for both homogeneous and heterogeneous systems. Rock properties affect hydrothermal fluid circulation, controlling both the range of variation and the temporal evolution of the observable signals. Low temperature fumaroles and low discharge rate may be affected by atmospheric conditions. Detailed parametric simulations were performed, aimed to understand the effects of system properties, such as permeability and gas reservoir overpressure, on diffuse degassing when air temperature and barometric pressure changes are applied to the ground surface. Hydrothermal circulation, however, is not only a characteristic of volcanic system. Hot fluids may be involved in several mankind problems, such as studies on geothermal engineering, nuclear waste propagation in porous medium, and Geological Carbon Sequestration (GCS). The current concept for large-scale GCS is the direct injection of supercritical carbon dioxide into deep geological formations which typically contain brine. Upward displacement of such brine from deep reservoirs driven by pressure increases resulting from carbon dioxide injection may occur through abandoned wells, permeable faults or permeable channels. Brine intrusion into aquifers may degrade groundwater resources. Numerical results show that pressure rise drives dense water up to the conduits, and does not necessarily result in continuous flow. Rather, overpressure leads to new hydrostatic equilibrium if fluids are initially density stratified. If warm and salty fluid does not cool passing through the conduit, an oscillatory solution is then possible. Parameter studies delineate steady-state (static) and oscillatory solutions.

Partial melting within the lower crust – Constraints from bulk rock geochemical data and trace element mineral analyses of granulites and migmatites from Central Finland

This PhD thesis concerns geochemical constraints on recycling and partial melting of Archean continental crust. A natural example of such processes was found in the Iisalmi area of Central Finland. The rocks from this area are Middle to Late Archean in age and experienced metamorphism and partial melting between 2.7-2.63 Ga. The work is based on extensive field work. It is furthermore founded on bulk rock geochemical data as well as in-situ analyses of minerals. All geochemical data were obtained at the Institute of Geosciences, University of Mainz using X-ray fluorescence, solution ICP-MS and laser ablation-ICP-MS for bulk rock geochemical analyses. Mineral analyses were accomplished by electron microprobe and laser ablation ICP-MS. Fluid inclusions were studied by microscope on a heating-freezing-stage at the Geoscience Center, University Göttingen. Part I focuses on the development of a new analytical method for bulk rock trace element determination by laser ablation-ICP-MS using homogeneous glasses fused from rock powder on an Iridium strip heater. This method is applicable for mafic rock samples whose melts have low viscosities and homogenize quickly at temperatures of ~1200°C. Highly viscous melts of felsic samples prevent melting and homogenization at comparable temperatures. Fusion of felsic samples can be enabled by addition of MgO to the rock powder and adjustment of melting temperature and melting duration to the rock composition. Advantages of the fusion method are low detection limits compared to XRF analyses and avoidance of wet-chemical processing and use of strong acids as in solution ICP-MS as well as smaller sample volumes compared to the other methods. Part II of the thesis uses bulk rock geochemical data and results from fluid inclusion studies for discrimination of melting processes observed in different rock types. Fluid inclusion studies demonstrate a major change in fluid composition from CO2-dominated fluids in granulites to aqueous fluids in TTG gneisses and amphibolites. Partial melts were generated in the dry, CO2-rich environment by dehydration melting reactions of amphibole which in addition to tonalitic melts produced the anhydrous mineral assemblages of granulites (grt + cpx + pl ± amph or opx + cpx + pl + amph). Trace element modeling showed that mafic granulites are residues of 10-30 % melt extraction from amphibolitic precursor rocks. The maximum degree of melting in intermediate granulites was ~10 % as inferred from modal abundances of amphibole, clinopyroxene and orthopyroxene. Carbonic inclusions are absent in upper-amphibolite facies migmatites whereas aqueous inclusion with up to 20 wt% NaCl are abundant. This suggests that melting within TTG gneisses and amphibolites took place in the presence of an aqueous fluid phase that enabled melting at the wet solidus at temperatures of 700-750°C. The strong disruption of pre-metamorphic structures in some outcrops suggests that the maximum amount of melt in TTG gneisses was ~25 vol%. The presence of leucosomes in all rock types is taken as the principle evidence for melt formation. However, mineralogical appearance as well as major and trace element composition of many leucosomes imply that leucosomes seldom represent frozen in-situ melts. They are better considered as remnants of the melt channel network, e.g. ways on which melts escaped from the system. Part III of the thesis describes how analyses of minerals from a specific rock type (granulite) can be used to determine partition coefficients between different minerals and between minerals and melt suitable for lower crustal conditions. The trace element analyses by laser ablation-ICP-MS show coherent distribution among the principal mineral phases independent of rock composition. REE contents in amphibole are about 3 times higher than REE contents in clinopyroxene from the same sample. This consistency has to be taken into consideration in models of lower crustal melting where amphibole is replaced by clinopyroxene in the course of melting. A lack of equilibrium is observed between matrix clinopyroxene / amphibole and garnet porphyroblasts which suggests a late stage growth of garnet and slow diffusion and equilibration of the REE during metamorphism. The data provide a first set of distribution coefficients of the transition metals (Sc, V, Cr, Ni) in the lower crust. In addition, analyses of ilmenite and apatite demonstrate the strong influence of accessory phases on trace element distribution. Apatite contains high amounts of REE and Sr while ilmenite incorporates about 20-30 times higher amounts of Nb and Ta than amphibole. Furthermore, trace element mineral analyses provide evidence for magmatic processes such as melt depletion, melt segregation, accumulation and fractionation as well as metasomatism having operated in this high-grade anatectic area.

Sviluppo di una metodologia per la modellazione geologica-geomeccanica ed il monitoraggio di reservoir adibiti a siti di stoccaggio di gas naturale

La valutazione dei rischi associati all’operatività dei sistemi di stoccaggio, quali la sismicità indotta e la subsidenza, è requisito basilare per una loro corretta gestione e progettazione, e passa attraverso la definizione dell’influenza sullo stato tensionale delle variazioni di pressione di poro nel sottosuolo. Principale scopo di questo progetto è lo sviluppo di una metodologia in grado di quantificare le deformazioni dei reservoir in funzione della pressione di poro, di tarare i modelli utilizzati con casi studio che presentino dati di monitoraggio reali, tali da consentire un confronto con le previsioni di modello. In questa tesi, la teoria delle inomogeneità è stata utilizzata, tramite un approccio semianalitico, per definire le variazioni dei campi elastici derivanti dalle operazioni di prelievo e immissione di fluidi in serbatoi geologici. Estensione, forma e magnitudo delle variazioni di stress indotte sono state valutate tramite il concetto di variazione dello sforzo critico secondo il criterio di rottura di Coulomb, tramite un’analisi numerica agli elementi finiti. La metodologia sviluppata è stata applicata e tarata su due reservoir sfruttati e riconvertiti a sistemi di stoccaggio che presentano dataset, geologia, petrofisica, e condizioni operative differenti. Sono state calcolate le variazioni dei campi elastici e la subsidenza; è stata mappata la variazione di sforzo critico di Coulomb per entrambi i casi. I risultati ottenuti mostrano buon accordo con le osservazioni dei monitoraggi, suggerendo la bontà della metodologia e indicando la scarsa probabilità di sismicità indotta. Questo progetto ha consentito la creazione di una piattaforma metodologica di rapido ed efficace utilizzo, per stimare l’influenza dei sistemi di stoccaggio di gas sullo stato tensionale della crosta terrestre; in fase di stoccaggio, permette di monitorare le deformazioni e gli sforzi indotti; in fase di progettazione, consente di valutare le strategie operative per monitorare e mitigare i rischi geologici associati a questi sistemi.

Lateral spreading and associated slope processes in fractured rock slabs

Landslides of the lateral spreading type, involving brittle geological units overlying ductile terrains, are a common occurrence in the sandstone and limestone plateaux of the northern Apennines of Italy. These instability phenomena can become particularly risky, when historical towns and cultural heritage sites built on the top of them are endangered. Neverthless, the mechanisms controlling the developing of related instabilities, i.e. toppling and rock falls, at the edges of rock plateaux are not fully understood yet. In addition, the groundwater flow path developing at the contact between the more permeable units, i.e. the jointed rock slab, and the relatively impermeable clay-rich units have not been already studied in details, even if they may play a role in this kind of instability processes, acting as eventual predisposing and/or triggering factors. Field survey, Terrestrial Laser Scanner and Close Range Photogrammetry techniques, laboratory tests on the involved materials, hydrogeological monitoring and modelling, displacements evaluation and stability analysis through continuum and discontinuum numerical codes have been performed on the San Leo case study, with the aim to bring further insights for the understanding and the assessment of the slope processes taking place in this geological context. The current research permitted to relate the aquifer behaviour of the rocky slab to slope instability processes. The aquifer hosted in the fractured slab leads to the development of perennial and ephemeral springs at the contact between the two units. The related piping erosion phenomena, together with slope processes in the clay-shales led to the progressive undermining of the slab. The cliff becomes progressively unstable due to undermining and undergoes large-scale landslides due to fall or topple.