Post-larval production of Macrobrachium rosenbergii using mass-cultured live food organisms

Macrobrachium rosenbergii post-larvae were produced in 1992 and 1993 using Artemia nauplii and cultured zooplankton Brachionus plicatilis (rotifier), Apocyclops dengizicus (copepod) and Moina sp. (cladoceran) supplemented with chopped Tubifex worms. In 1992 (first trial) two experiments were carried out under water temperature range of 24.5 to 28°C and 26.0 to 28.5 °C respectively and corresponding post-larval production was 5.6% and 86.3%. The duration of experiments was 58 and 40 days. During second trial in 1993 water temperature varied between 25.0 to 27.0°C. At the end of 59 days the post-larvae were found to be 44% of the total number of larvae stocked on the first day.

Evaluation of some formulated diets for rearing the post-larvae of Macrobrachium rosenbergii

Macrobrachium rosenbergii post-larvae with an average weight of 6.26 ± 0.23 mg and an average length of 10.67 ± 0.13 mm were fed with one of the five experimental diets having graded levels of lipid (5.0, 7.5, 10.0, 12.5 and 15.0%) to satiation two times a day to study their effect on growth, survival and feed utilisation. The highest weight gain was observed in post-larvae fed 7.5% lipid, although there was no significant difference (p>0.05) between groups fed 7.5 and 10.0% lipid. Similar effect was observed in the specific growth rate and protein efficiency ratio of post-larvae fed the diet with 7.5 and 10.0% lipid. The lowest feed conversion ratio was obtained in postlarvae fed the diet with 7.5% lipid. The survival rates of post-larvae fed on various levels of dietary lipid differed significantly (p<0.05) after 15 days of rearing period. Significantly lower survival was observed in the diet with 15.0% lipid level. Dietary lipid did not significantly affect prawn carcass protein, lipid and ash contents. Based on the data analysis (ANOVA – one way analysis), the dietary lipid requirement for 15 days of nursery rearing of Macrobrachium rosenbergii post-larvae was estimated to be 7.5 to 10.0% under experimental conditions in this study.

Post-processing of vertical-cavity surface-emitting lasers for transverse mode and polarization control

The operation on how high quality single-mode operation can be readily attained on etching circles in multimode devices is discussed. Arrays of such spots can also be envisaged. Control of the polarization state is also achieved by use of deep line etches. The output filaments and beam shapes of the conventional multimode vertical cavity surface emitting lasers (VCSEL) is shown to be engineered in terms of their positions, widths, and polarizations by use of focused ion beam etching (FIBE). Several GaAs quantum well top-emitting devices with cavity diameters of 10 μm and 18 μm were investigated.

Mode control in vertical-cavity surface-emitting lasers by post-processing using focused ion-beaih etching

Single-mode emission is achieved in previously multimode gain-guided vertical-cavity surface-emitting lasers (VCSEL's) by localized modification of the mirror reflectivity using focused ion-beam etching. Reflectivity engineering is also demonstrated to suppress transverse mode emission in an oxide-confined device, reducing the spectral width from 1.2 nm to less than 0.5 nm.

A survey of research and scientific services in East Africa, 1947-56

This "Survey of Research and Scientific Services in East Arica 1947-1956" has been prepared by Dr. E. B. Worthington, who held the post of Scientific Secretary in the Office of the Chief Secretary to the East African Governor's Conference and subsequently in the Administrator's Office of the East Mrica High Commission during the period January, 1947-May, 1951. Dr. Worthington is now Secretary General of the Scientific Council for, Arica South of the Sahara

Fecundity, morphometry post embryonic growth and development of Caridina simoni Bouvier (Decapoda: Atyidae)

The fecundity, morphometry and the post embryonic development of Caridina simoni which is the commonest atyid shrimp in Sri Lanka were studied. The fecundity values ranged from 12-55. There was a linear relationship between the logarithmic values of fecundity and body length and the same relationship was obtained for body length and weight. It was seen that the developmental period of this species was less than six days and during development it passed through six zoeal stages.

Effect of combined thyroxine and cortisol treatment on hatching of eggs, post-embryonic growth and survival of larvae of Heteropneustes fossilis

In order to record the effects of thyroxine and cortisol (individual/combined) on hatching, post-embryonic growth and survival of larvae of Heteropneustes fossilis, newly fertilized eggs were given bath immersion treatments of L-thyroxine (T sub(4); 0.05 mg/l), cortisol (0.50 mg/l) and T sub(4)+ cortisol (0.05 mg/l+0.50 mg/l) for 15 days. Hatching of eggs, growth and survival of the larvae improved significantly (P<0.001) in the hormone treated groups as compared to those of control. The frequency of deformities was reduced in the combined hormone treatment group. The present observations suggest that the advanced digestive function probably induced by T sub(4)+cortisol treatment might have resulted in improvement in food utilization during the critical phases of first feeding and promoted vital developmental processes resulting in uniform growth, decreased mortality, better survival and transformation of larvae to juveniles. This combined hormone therapy appears to have practical utility in fish hatchery practice for better success in larval rearing.

Post impoundment changes in the fish fauna of Kaptai reservoir, Bangladesh

Based on the present investigation and reviewing the published and unpublished documents critically, this communication considers the post impoundment changes in the fish fauna of Kaptai reservoir. Investigation reveals that a total of 73 species of fish belongs to 47 genera, 25 families and 2 species of prawn are present in the reservoir. Of them, 31 are commercially important, 6 and 9 species are newly identified.

Predicting the performance of an office under climate change: A study of metrics, sensitivity and zonal resolution

Climate change is expected to have significant impact on the future thermal performance of buildings. Building simulation and sensitivity analysis can be employed to predict these impacts, guiding interventions to adapt buildings to future conditions. This article explores the use of simulation to study the impact of climate change on a theoretical office building in the UK, employing a probabilistic approach. The work studies (1) appropriate performance metrics and underlying modelling assumptions, (2) sensitivity of computational results to identify key design parameters and (3) the impact of zonal resolution. The conclusions highlight the importance of assumptions in the field of electricity conversion factors, proper management of internal heat gains, and the need to use an appropriately detailed zonal resolution. © 2010 Elsevier B.V. All rights reserved.

The role of adaptive thermal comfort in the prediction of the thermal performance of a modern mixed-mode office building in the UK under climate change

Climate change is becoming a serious issue for the construction industry, since the time scales at which climate change takes place can be expected to show a true impact on the thermal performance of buildings and HVAC systems. In predicting this future building performance by means of building simulation, the underlying assumptions regarding thermal comfort conditions and the related heating, ventilating and air conditioning (HVAC) control set points become important. This article studies the thermal performance of a reference office building with mixedmode ventilation in the UK, using static and adaptive thermal approaches, for a series of time horizons (2020, 2050 and 2080). Results demonstrate the importance of the implementation of adaptive thermal comfort models, and underpin the case for its use in climate change impact studies. Adaptive thermal comfort can also be used by building designers to make buildings more resilient towards change. © 2010 International Building Performance Simulation Association (IBPSA).