High dielectric constant of SrTiO3 thin films prepared by chemical process

SrTiO3 thin films were prepared by the polymeric precursor method and deposited by spin-coating onto Pt/Ti/SiO2/Si(100) substrates. The spin-coated films heat treated at 700 degrees C were crack-free, dense, and homogeneous. Microstructural and morphological evaluations were followed by grazing incident X-ray, scanning electron microscopy and atomic force microscopy. Dielectric studies indicated a dielectric constant of about 475, which is higher than that of ceramic SrTiO3, and a factor dissipation of about 0.050 at 100 kHz. SrTiO3 thin films were found to have paraelectric properties with C-V characteristics. (C) 2000 Kluwer Academic Publishers.

Effect of niobia on the crystal structure and dielectric characteristics of Pb(Zr0.45Ti0.55)O-3 prepared from polymeric precursor

The influence of niobia addition on the phase formation and dielectric properties of Pb(Zr0.45Ti0.55)O-3 powder prepared from polymeric precursor was analyzed. The weight fraction and unit-cell volume of the tetragonal phase decreased, and the mass fraction of the rhombohedral phase increased, with increasing niobia concentration. The rhombohedral unit-cell volume increased up to 5 mol% of added Nb and then decreased. Small amounts of pyrochlore and tetragonal zirconia phases were observed in PZT powder with more than 10 mol% Nb. These results were interpreted as an indication that the Nb ion was substituted for the zirconium ion in the tetragonal phase. For sintered PZT samples at 1100 degrees C, no free-zirconia phase was observed. The dielectric constant increased with the niobia addition up to 5 mol% and decreased for higher concentrations. The Curie temperature decreased with niobia addition up to 10 mol% before the formation of pyrochlore phase. (C) 2000 Elsevier B.V. Ltd. All rights reserved.

The characteristics of a test liquid formulation for use in evaluating the performance of handling and metering systems

Injection metering systems are an important option for the development of pesticide application equipment, with advantages relating to minimising the need for disposal of unused pesticide, improving the ease of cleaning and optimising the accuracy of chemical application. For all injection systems, characteristics such as the steady-state accuracy of delivered dose, dose stability and the time response for dose step changes are related to the ability of the system to operate with different chemical formulations. A system designed to inject liquids should be able to accommodate changes in viscosity and density. The aim of this study was to develop a methodology for testing chemical injection systems using liquids with different viscosities. The experimental arrangement simulating applications with injection metering systems used dye and salt solutions as tracers. Tests were conducted to analyse the influence of salt on the characteristics of the water and a viscous solution. Results showed that the salt interfered with the dye stability in the water solution. In tests with a viscous test liquid, the salt was introduced at different steps during the mixing process, providing four different liquids to be analysed in terms of viscosity, density and pH. Some differences in liquid characteristics were found which could influence the performance of the injection systems.

Anthracnose control and mango quality (Mangifera indica L.) cv. van dyke after hydrothermal and chemical treatment

Anthracnose causes severe damage to the mango skin. Therefore, there is need to do the post-harvest phytosanitary treatment of the fruits through soaking in fungicide solution, which associated with the hydrothermal treatment has resulted into improved benefits. The present work has aimed at studying anthracnose control and post-harvest quality of mangoes (Mangifera indica L.), cv. Van Dyke after hydrothermal treatment associated with chemical through the physical, physicochemical, chemical and phytopathologic analyses. The mangoes coming from the commercial orchard of the town of Jana ba-MG, of the 2000 crop, were harvested at the commercial maturation stage. After selection according to color uniformity, size and absence of mechanic and physiologic injuries, they were shipped in plastic boxes to the EPAMIG - CTNM - Nova Porteirinha - MG, fruit post-harvest laboratory, where the samples were submitted to the hydrothermal treatment in cold bath in solution containing the fungicides Thiabendazole (Tecto 400 mL/100L), Proclaraz (Sportak 10L/100L) and Imazalil (Magnate 200mL/100L). After air-drying, the fruits were packed in plastic trays and stored at room temperature (25 +/- 2 degrees C and RH 70%) for a 12-day period and evaluated as to the intrinsic quality characteristics every 4 days. The experiment was conducted a completely randomized with 8 treatments, 4 replicates and experimental unit consisting of 4 fruits. The variations of pH, total soluble solids, total titrable acidity and total soluble sugars have not endangered the organoleptic characteristics of mangoes cv. Van Dyke stored under room temperature (25 +/- 2 degrees C and RH 70%) till 8 days' storage. The association of the hydrothermal treatment with the chemical was efficient in fruit anthracnose control for till 12 days' storage. The fungicide Prochloraz (Sportak 110 mL/100L), associated with the hydrothermal treatment, completely inhibited the appearance of anthracnose symptoms.

Preparation, microstructural and electrical characterization of SrTiO3 thin films prepared by chemical route

Polycrystalline SrTiO3 thin films having a cubic perovskite structure were prepared at different temperatures by the polymeric precursor method on platinum-coated silicon substrate. Crystalline films with uniform composition and thickness were prepared by spin-coating and the post-deposition heat treatment was carried out at different temperatures. The film showed good structural, dielectric, and insulating properties, Scanning electron microscopy (SEM) micrographs showed no occurrence of interdiffusion between the bottom electrode (platinum) and the film during post-annealing, indicating a stable interface between the SrTiO3 and the bottom electrode. The dielectric constant and dissipation factor at a frequency of 100 kHz were 250 and 0.01, respectively, for a 360 nm thick film annealed at 600 degreesC. The capacitance versus applied voltage characteristics showed that the capacitance was almost independent of the applied voltage. The I-V characteristics were ohmic in low fields and a Schottky emission and/or Poole-Frenkel emission were postulated in high fields. Room temperature leakage current density was found to be in the order of 10(-7) A/cm(2) for a 360 nm thick film in an applied electric field of about 100 kV/cm. The charge storage density of 36 fC/mum(2) was obtained in an applied electric field of about 100 kV/cm. (C) 2001 Published by Elsevier B.V. Ltd. All rights reserved.

Effects of ion beam on nanoindentation characteristics of glassy polymeric carbon surface

Glassy polymeric carbon (GPC) is a useful material for medical applications due to its chemical inertness and biocompatible characteristics. Mitral and aortic and hydrocephalic valves are examples of GPC prosthetic devices that have been fabricated and commercialized in Brazil. In this work, ion beam was used to improve the mechanical characteristics of GPC surface and therefore to avoid the propagation of microcracks where the cardiac valves are more fragile. A control group of phenolic resin samples heat-treated at 300, 400, 700, 1000, 1500, and 2500 degrees C was characterized by measuring their hardness and Young's reduced elastic modulus with the depth of indentation. The control group was compared to results obtained with samples heat-treated at 700, 1000, and 1500 degrees C and bombarded with energetic ions of silicon, carbon, oxygen, and gold at energies of 5, 6, 8, and 10 MeV, respectively, with fluences between 10x10(13) and 10x10(16) ions/cm(2). GPC nonbombarded samples showed that hardness depends on the heat treatment temperature (HTT), with a maximum hardness for heat treatment at 1000 degrees C. The comparison between the control group and bombarded group also showed that hardness, after bombardment, had a greater increase for samples prepared at 700 degrees C than for samples prepared at higher temperatures. The Young's elastic modulus presents an exponential relationship with depth. The parameters obtained by fitting depend on the HTT and on the ion used in the bombardment more than on energy and fluence. The hardness results show clearly that bombardment can promote carbonization, increase the linkage between the chains of the polymeric material, and promote recombination of broken bonds in lateral groups that are more numerous for samples heat-treated at 700 degrees C. (c) 2004 Elsevier B.V. All rights reserved.

Structural characteristics of silica sonogels prepared with additions of isopropyl alcohol

Wet silica gels with similar to 1.4 x 10(-3) mol SiO2/cm(3) and similar to 92 vol% liquid phase were obtained from sonohydrolysis of tetraethoxysilane (TEOS) with different additions of isopropyl alcohol ( IPA). The IPA/TEOS molar ratio R was changed from 0 to 4. Aerogels were obtained by supercritical CO2 extraction. The samples were analyzed by small-angle X-ray scattering (SAXS) and nitrogen adsorption. The wet gels exhibit mass fractal structure with fractal dimension increasing from D similar to 2.10 to D similar to 2.22, characteristic length xi decreasing from similar to 9.5 to similar to 6.9 nm, as R increases from 0 to 4, and an estimated characteristic length for the primary silica particles lower than similar to 0.3 nm. The supercritical process apparently eliminates a fraction of the porosity, increasing the mass fractal dimension and shortening the fractality domain in the mesopore region. The fundamental role of isopropyl alcohol on the structure of the resulting aerogels is to decrease the porosity and the pore mean size as R changes from pure TEOS to R = 4. A secondary structure appearing in the micropore region of the aerogels can be described as a mass/surface fractal structure, with correlated mass fractal dimension D-m similar to 2.7 and surface fractal dimension D-s similar to 2.3, as inferred from SAXS and nitrogen adsorption data.

Dielectric properties and microstructure of SrTiO3/BaTiO3 multilayer thin films prepared by a chemical route

Multilayer thin films with perovskite structures were produced by the polymeric precursor method. SrTiO3/BaTiO3 (STO/BTO) multilayers were deposited on Pt(111)/Ti/SiO2/Si(100) substrates by the spin-coating technique and heated in air at 700 degreesC. The microstructure and crystalline phase of the multilayered thin films were examined by field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), resolution-high transmission electron microscopy (HRTEM), atomic force microscopy (AFM) and X-ray diffraction. The SrTiO3/BaTiO3 multilayer thin films consisted of grainy structures with an approximate grain size of 60 nm. The multilayered thin films showed a very clear interface between the components. The SrTiO3/BaTiO3 multilayer thin films revealed dielectric constants of approximately 527 and loss tangents of 0.03 at 100 kHz. The dielectric constant calculated for this multilayer film system is the value of the sum of each individual component of the film, i.e. The total value of the sum of each SrTiO3 (STO) and BaTiO3 (BTO) layer. The multilayer SrTiO3/BaTiO3 obtained by the polymeric precursor method, also showed a ferroelectric behavior with a remanent polarization of 2.5 muC/cm(2) and a coercive field of 30 kV/cm. The multilayer films displayed good fatigue characteristics under bipolar stressing after application of 10(10) switching cycles. (C) 2001 Published by Elsevier B.V. B.V. All rights reserved.

(Sr,Tm)ZrO3 powders prepared by the polymeric precursor method: Synthesis, optical properties and morphological characteristics

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Strain behavior of lanthanum modified BiFeO3 thin films prepared via soft chemical method

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Development of chemical vapor deposition diamond burrs using hot filament

The fabrication of boring tools (burrs) for dentistry with the use of a hot-filament chemical vapor deposition (CVD) system, to form the diamond abrading structure, is reported here. The diamond was synthesized from a methane/freon gas mixture diluted in hydrogen. Comparative drilling tests with conventional diamond burrs and the CVD diamond burrs in borosilicate glasses demonstrated a lifetime more than 20 times larger for the CVD diamond burrs. Also, heat flow experiments in dentine showed that the CVD diamond burrs induce temperature gradients of the same order as the conventional ones. These characteristics of the CVD diamond burrs are highly desirable for odontological applications where the burrs' lifetime and the low temperature processing are essential to the quality and comfort of the treatment. © 1996 American Institute of Physics.

Physico-chemical parameter correlations in the [RuCl2(CO)(L)(PPh3)2] complexes (L = N-heterocycles)

Fourteen complexes in the series [RuCl2(CO)(L)(PPh3)2] (where L = N-heterocycles) have been prepared and characterized by IR and NMR spectroscopies, and cyclic voltammetry. A good correlation is found between observed and calculated electrochemical potentials; E1/2 vs pKa or (Gp, σm for a series of similar ligands. It is now reported that the carbonyl stretching frequency, νCO, and the 13C and 31P NMR signals do not correlate well with any of the physico-chemical parameters used (E1/2, Taft's and Hammett's parameters). This behaviour is probably due to the characteristics of the Ru(II) species, which does not transmit the steric and electron donor/acceptor properties of the ligands to the carbonyl group, or because the measurements are not able to detect the effect induced by the changes in the ligand L. Indeed, good correlations are obtained when the measurements directly involve the metal centre, as is the case in the E1/2 measurements. Crystals of o[RuCl2(CO)(4-pic)(PPh3)2] are monoclinic, space group P21/n, a = 12.019(2), b = 13.825(3) and c = 22.253(3) . The structure was solved by the Patterson method and was refined by full-matrix least-squares procedure to R = 0.054 and Rw = 0.055, for 2114 reflections with I > 3σ(I). For L = 2-acetylpyridine and 2-methylimidazole, complexes with formulae [RuCl2(CO)(L)(PPh3)] · L and [RuCl2(CO)(L)2 (PPh3)], respectively, were obtained. © 1998 Elsevier Science Ltd. All rights reserved.

Influence of organic and chemical fertilization on the yield of flowers, contents and composition of essential oil of (Chamomilla recutita (L.) Rauschert)

A field experiment was conducted with chamomile (Chamomilla recutita [L.] Rauschert), in an area of the Olericulture and Medicinal Plants of the Horticulture Department at UNESP - Jaboticabal Campus, with the aim to evaluate the influence of organic and chemical fertilization on the yield of flowers, and content and composition of the essential oil of chamomile. The experimental design for the yield of flowers consisted of randomized blocks with 7 treatments and 4 replications, for the analysis of the contents and composition of the oil, the completely randomized block was used and for analysis of the correlation between harvesting and treatment, the split-plot design into randomized blocks was used. The treatments tested were: no fertilization, green manure (Mucuna aterrima + Crotalaria spectabilis), green manure (plant cocktail), organic fertilizer (farmyard manure), N as urea, N as ammonium sulphate, NPK with N supplement as ammonium sulphate. There was no influence of the treatments on the yield of flowers nor on the essential oil content; on the other hand both characteristics did show significant differences in harvesting times (Tukey 5%). The main yield was 885.90 kg/ha dry flowers and the mean oil content was 0,86%. The green manure treatment (M. aterrima + C. spectabilis) showed a higher percentage of chamazulene content, with a highly significant difference in harvesting times (Tukey 1%). The a-bisabolol percentages did not evidence significant differences between treatments. However, among harvesting times, there was a variation. A negative correlation was verified between the chamazulene and abisabolol percentages; the first increasing - from 21.02 to 36.17% - and the latter decreasing - from 14.12 to 8.72 % - from the first to the sixth harvest. The observed mean content of chamazulene was 14.64 % and a-bisabolol was 16.72 %.

Physical-chemical characterization of processing tomato fruit

Fruit of 28 tomato cultivars for industrial processing were characterized to identify cultivars with potential for in natura consumption. The experiment was carried out in Jaboticabal-SP, Brazil (21o15'22'' South, 48o18'58'' West, altitude 595 m), on a Haplorthox soil during June-December. The cultivars used in this study were: H 7155, Hypeel 108, Andino, U 573, H 9036, Ipa 6, H 9494, AG 33, Yuba, RPT 1294, AG 72, Peelmech, Curicó, Hypeel 45, RPT 1478, H 9492, H 9498, H 2710, Hitech 45, Halley, Botu 13, H 9553, U 646, NK 1570, AG 45, RPT 1095, RPT 1570 and PSX 37511. The experimental design was randomized blocks, replicated four times. Ten fruits per plot were analyzed, evaluating the following characteristics: shape (oblong or round); length and diameter (mm); external and internal coloration; presence of fissures; number of loci; pulp thickness (mm); soluble solids content (Brix) and total acidity. Only cultivars Hypeel 108, AG 72, NK 1570, RPT 1570 had oblong fruit. Cultivars which had pulp thicker than 5.5 mm, a characteristic which is directly related to fruit yield for industrial purposes were: Ipa 6, Andino, U 646, H 9553, RPT 1294 and Hypeel 108. Cultivars Ipa 6 and Andino also presented elevated values for length, diameter and pulp thickness, indicating them as quality material for industry or, alternatively, for in natura market. Among the cultivars which presented better values for acidity (higher or equal to 0.3 g citric acid 100 g-1) were RPT 1095, AG 45, H 9553 and Hypeel 45.

Cutting characteristics of dental diamond burs made with CVD technology

The aim of this study was to determine the cutting ability of chemical vapor deposition (CVD) diamond burs coupled to an ultrasonic dental unit handpiece for minimally invasive cavity preparation. One standard cavity was prepared on the mesial and distal surfaces of 40 extracted human third molars either with cylindrical or with spherical CVD burs. The cutting ability was compared regarding type of substrate (enamel and dentin) and direction of handpiece motion. The morphological characteristics, width and depth of the cavities were analyzed and measured using scanning electron micrographs. Statistical analysis using the Kruskal-Wallis test (p < 0.05) revealed that the width and depth of the cavities were significantly greater when they were prepared on dentin. Wider cavities were prepared when the cylindrical CVD bur was used, and deeper cavities resulted from preparation with the spherical CVD bur. The direction of handpiece motion did not influence the size of the cavities, and the CVD burs produced precise and conservative cutting.