Klassifikationsgestützte on-line Adaption eines robusten beobachterbasierten Fehlerdiagnoseansatzes für nichtlineare Systeme

Diese Arbeit behandelt die Problemstellung der modellbasierten Fehlerdiagnose für Lipschitz-stetige nichtlineare Systeme mit Unsicherheiten. Es wird eine neue adaptive Fehlerdiagnosemethode vorgestellt. Erkenntnisse und Verfahren aus dem Bereich der Takagi-Sugeno (TS) Fuzzy-Modellbildung und des Beobachterentwurfs sowie der Sliding-Mode (SM) Theorie werden genutzt, um einen neuartigen robusten und nichtlinearen TS-SM-Beobachter zu entwickeln. Durch diese Zusammenführung lassen sich die jeweiligen Vorteile beider Ansätze miteinander kombinieren. Bedingungen zur Konvergenz des Beobachters werden als lineare Matrizenungleichungen (LMIs) abgeleitet. Diese Bedingungen garantieren zum einen die Stabilität und liefern zum anderen ein direktes Entwurfsverfahren für den Beobachter. Der Beobachterentwurf wird für die Fälle messbarer und nicht messbarer Prämissenvariablen angegeben. Durch die TS-Erweiterung des in dieser Arbeit verwendeten SM-Beobachters ist es möglich, den diskontinuierlichen Rückführterm mithilfe einer geeigneten kontinuierlichen Funktion zu approximieren und dieses Signal daraufhin zur Fehlerdiagnose auszuwerten. Dies liefert eine Methodik zur Aktor- und Sensorfehlerdiagnose nichtlinearer unsicherer Systeme. Gegenüber anderen Ansätzen erlaubt das Vorgehen eine quantitative Bestimmung und teilweise sogar exakte Rekonstruktion des Fehlersignalverlaufs. Darüber hinaus ermöglicht der Ansatz die Berechnung konstanter Fehlerschwellen direkt aus dem physikalischen Vorwissen über das betrachtete System. Durch eine Erweiterung um eine Betriebsphasenerkennung wird es möglich, die Schwellenwerte des Fehlerdiagnoseansatzes online an die aktuelle Betriebsphase anzupassen. Hierdurch ergibt sich in Betriebsphasen mit geringen Modellunsicherheiten eine deutlich erhöhte Fehlersensitivität. Zudem werden in Betriebsphasen mit großen Modellunsicherheiten Falschalarme vermieden. Die Kernidee besteht darin, die aktuelle Betriebsphase mittels eines Bayes-Klassikators in Echtzeit zu ermitteln und darüber die Fehlerschwellen an die a-priori de nierten Unsicherheiten der unterschiedlichen Betriebsphasen anzupassen. Die E ffektivität und Übertragbarkeit der vorgeschlagenen Ansätze werden einerseits am akademischen Beispiel des Pendelwagens und anderseits am Beispiel der Sensorfehlerdiagnose hydrostatisch angetriebener Radlader als praxisnahe Anwendung demonstriert.

Optical Characterization of Organic Gain Materials for UV-emitting Hybrid Complex Coupled VCSELs

In this thesis, optical gain measurement setup based on variable stripe length method is designed, implemented and improved. The setup is characterized using inorganic and organic samples. The optical gain of spiro-quaterphenyl is calculated and compared with measurements from the setup. Films with various thicknesses of spiro-quaterphenyl, methoxy-spiro-quaterphenyl and phenoxy-spiro-quaterphenyl are deposited by a vacuum vapor deposition technique forming asymmetric slab waveguides. The optical properties, laser emission threshold, optical gain and loss coefficient for these films are measured. Additionally, the photodegradation during pumping process is investigated.

Hybrid optimization schemes for quantum control

Optimal control theory is a powerful tool for solving control problems in quantum mechanics, ranging from the control of chemical reactions to the implementation of gates in a quantum computer. Gradient-based optimization methods are able to find high fidelity controls, but require considerable numerical effort and often yield highly complex solutions. We propose here to employ a two-stage optimization scheme to significantly speed up convergence and achieve simpler controls. The control is initially parametrized using only a few free parameters, such that optimization in this pruned search space can be performed with a simplex method. The result, considered now simply as an arbitrary function on a time grid, is the starting point for further optimization with a gradient-based method that can quickly converge to high fidelities. We illustrate the success of this hybrid technique by optimizing a geometric phase gate for two superconducting transmon qubits coupled with a shared transmission line resonator, showing that a combination of Nelder-Mead simplex and Krotov’s method yields considerably better results than either one of the two methods alone.

Investigation of Multiphase Power Converter using Integrated Coupled Inductor Regarding Electric Vehicle Application

The challenge of reducing carbon emission and achieving emission target until 2050, has become a key development strategy of energy distribution for each country. The automotive industries, as the important portion of implementing energy requirements, are making some related researches to meet energy requirements and customer requirements. For modern energy requirements, it should be clean, green and renewable. For customer requirements, it should be economic, reliable and long life time. Regarding increasing requirements on the market and enlarged customer quantity, EVs and PHEV are more and more important for automotive manufactures. Normally for EVs and PHEV there are two important key parts, which are battery package and power electronics composing of critical components. A rechargeable battery is a quite important element for achieving cost competitiveness, which is mainly used to story energy and provide continue energy to drive an electric motor. In order to recharge battery and drive the electric motor, power electronics group is an essential bridge to convert different energy types for both of them. In modern power electronics there are many different topologies such as non-isolated and isolated power converters which can be used to implement for charging battery. One of most used converter topology is multiphase interleaved power converter, pri- marily due to its prominent advantages, which is frequently employed to obtain optimal dynamic response, high effciency and compact converter size. Concerning its usage, many detailed investigations regarding topology, control strategy and devices have been done. In this thesis, the core research is to investigate some branched contents in term of issues analysis and optimization approaches of building magnetic component. This work starts with an introduction of reasons of developing EVs and PEHV and an overview of different possible topologies regarding specific application requirements. Because of less components, high reliability, high effciency and also no special safety requirement, non-isolated multiphase interleaved converter is selected as the basic research topology of founded W-charge project for investigating its advantages and potential branches on using optimized magnetic components. Following, all those proposed aspects and approaches are investigated and analyzed in details in order to verify constrains and advantages through using integrated coupled inductors. Furthermore, digital controller concept and a novel tapped-inductor topology is proposed for multiphase power converter and electric vehicle application.

Grupo de trabajo on line de prevenci??n de riesgos

Se presenta experiencia educativa que propone el proceso de formaci??n y desarrollo de un grupo de trabajo formado por profesorado de las distintas etapas educativas. Lo realiza la Delegaci??n de Educaci??n de Granada. El objetivo principal es: fomentar una aut??ntica cultura preventiva mediante la promoci??n de la mejora de la educaci??n en dicha materia en todos los ??mbitos educativos.

Parallel Coupled Micro-Macro Actuators

This thesis presents a new actuator system consisting of a micro-actuator and a macro-actuator coupled in parallel via a compliant transmission. The system is called the Parallel Coupled Micro-Macro Actuator, or PaCMMA. In this system, the micro-actuator is capable of high bandwidth force control due to its low mass and direct-drive connection to the output shaft. The compliant transmission of the macro-actuator reduces the impedance (stiffness) at the output shaft and increases the dynamic range of force. Performance improvement over single actuator systems was expected in force control, impedance control, force distortion and reduction of transient impact forces. A set of quantitative measures is proposed and the actuator system is evaluated against them: Force Control Bandwidth, Position Bandwidth, Dynamic Range, Impact Force, Impedance ("Backdriveability'"), Force Distortion and Force Performance Space. Several theoretical performance limits are derived from the saturation limits of the system. A control law is proposed and control system performance is compared to the theoretical limits. A prototype testbed was built using permanenent magnet motors and an experimental comparison was performed between this actuator concept and two single actuator systems. The following performance was observed: Force bandwidth of 56Hz, Torque Dynamic Range of 800:1, Peak Torque of 1040mNm, Minimum Torque of 1.3mNm. Peak Impact Force was reduced by an order of magnitude. Distortion at small amplitudes was reduced substantially. Backdriven impedance was reduced by 2-3 orders of magnitude. This actuator system shows promise for manipulator design as well as psychophysical tests of human performance.

Model-Based Matching of Line Drawings by Linear Combinations of Prototypes

We describe a technique for finding pixelwise correspondences between two images by using models of objects of the same class to guide the search. The object models are 'learned' from example images (also called prototypes) of an object class. The models consist of a linear combination ofsprototypes. The flow fields giving pixelwise correspondences between a base prototype and each of the other prototypes must be given. A novel image of an object of the same class is matched to a model by minimizing an error between the novel image and the current guess for the closest modelsimage. Currently, the algorithm applies to line drawings of objects. An extension to real grey level images is discussed.

On Degeneracy of Linear Reconstruction from Three Views: Linear Line Complex and Applications

This paper investigates the linear degeneracies of projective structure estimation from point and line features across three views. We show that the rank of the linear system of equations for recovering the trilinear tensor of three views reduces to 23 (instead of 26) in the case when the scene is a Linear Line Complex (set of lines in space intersecting at a common line) and is 21 when the scene is planar. The LLC situation is only linearly degenerate, and we show that one can obtain a unique solution when the admissibility constraints of the tensor are accounted for. The line configuration described by an LLC, rather than being some obscure case, is in fact quite typical. It includes, as a particular example, the case of a camera moving down a hallway in an office environment or down an urban street. Furthermore, an LLC situation may occur as an artifact such as in direct estimation from spatio-temporal derivatives of image brightness. Therefore, an investigation into degeneracies and their remedy is important also in practice.

Cell-line Engineering of Chinese Hamster Ovary Cells for Low-temperature Culture

Developments in mammalian cell culture and recombinant technology has allowed for the production of recombinant proteins for use as human therapeutics. Mammalian cell culture is typically operated at the physiological temperature of 37°. However, recent research has shown that the use of low-temperature conditions (30-33°) as a platform for cell-culture results in changes in cell characteristics, such as increased specific productivity and extended periods of cell viability, that can potentially improve the production of recombinant proteins. Furthermore, many recent reports have focused on investigating low-temperature mammalian cell culture of Chinese hamster ovary (CHO) cells, one of the principal cell-lines used in industrial production of recombinant proteins. Exposure to low ambient temperatures exerts an external stress on all living cells, and elicits a cellular response. This cold-stress response has been observed in bacteria, plants and mammals, and is regulated at the gene level. The exact genes and molecular mechanisms involved in the cold-stress response in prokaryotes and plants have been well studied. There are also various reports that detail the modification of cold-stress genes to improve the characteristics of bacteria or plant cells at low temperatures. However, there is very limited information on mammalian cold-stress genes or the related pathways governing the mammalian cold-stress response. This project seeks to investigate and characterise cold-stress genes that are differentially expressed during low-temperature culture of CHO cells, and to relate them to the various changes in cell characteristics observed in low-temperature culture of CHO cells. The gene information can then be used to modify CHO cell-lines for improved performance in the production of recombinant proteins.

Optimizing Product Line Designs: Efficient Methods and Comparisons

We compare a broad range of optimal product line design methods. The comparisons take advantage of recent advances that make it possible to identify the optimal solution to problems that are too large for complete enumeration. Several of the methods perform surprisingly well, including Simulated Annealing, Product-Swapping and Genetic Algorithms. The Product-Swapping heuristic is remarkable for its simplicity. The performance of this heuristic suggests that the optimal product line design problem may be far easier to solve in practice than indicated by complexity theory.

Em-Line!

Investigadors del grup VICOROB de la UdG participen en els assajos clínics del projecte EM-Line! Es tracta d’un programa perquè els afectats d’esclerosi múltiple puguin fer rehabilitació cognitiva des de casa seva

Context constraints, prior vocabulary knowledge and on-line inferences in reading

Resumen tomado de la publicaci??n

Active control of structures with uncertain coupled subsystems and actuator dynamics

This paper deals with the problem of stabilizing a class of structures subject to an uncertain excitation due to the temporary coupling of the main system with another uncertain dynamical subsystem. A Lyapunov function based control scheme is proposed to attenuate the structural vibration. In the control design, the actuator dynamics is taken into account. The control scheme is implemented by using only feedback information of the main system. The effectiveness of the control scheme is shown for a bridge platform with crossing vehicle

10 easy steps to ease on-line communication

There are many different ways to communicate on-line now days from chat rooms, forums to e-mail, instant messaging, blogs and personal spaces. Some have clearly stated rules and some depend on unwritten codes of behaviour. Here are a few general tips provided that will hopefully make those occasions where learning and teaching are taking place more worthwhile.