Effect of microwave disinfection on the bond strength of denture teeth to acrylic resins

During microwave disinfection, the dentures are exposed to water at high temperature and this may affect the bond between the denture teeth and the acrylic resin from which dentures are made. In this study, a shear test was used to evaluate the effect of microwave disinfection (650W/6 min) on the bond strength of two types of denture teeth to three acrylic resins, with different polymerization methods. The specimens were submitted to the shear tests (0.5 mm/min) after: immersion in water (37 degrees C) for 48 h or 8 days (controls); two or seven cycles of microwave disinfection (test groups). Data (MPa) were analyzed using three-way ANOVA and Tukey HSD test (alpha = 0.05). Microwave disinfection did not adversely affect the bond strength of all tested materials with the exception of QC-20 bonded to SR Vivodent PE, for which a significant reduction was recorded after seven cycles of irradiation. (C) 2007 Elsevier Ltd. All rights reserved.

Study of Densification Process and Microstructure for Highly Dense Doped MgB2 Bulk Samples

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

A new fossil Adamussium (Bivalvia: Pectinidae) from Antarctica

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Using network connectance and autonomy analyses to uncover patterns of photosynthetic responses in tropical woody species

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

INFLUENCE of ENCAPSULATING MATERIALS on WATER SORPTION ISOTHERMS of VACUUM-DRIED PERSIMMON PULP POWDER

Water sorption isotherms for vacuum-dried persimmon pulp (PP) powder were determined in the temperature range of 20-50C, and the effects of maltodextrin (MD) or gum arabic (GA) addition on the water sorption behavior of the dried powders were analyzed. Several models were evaluated to fit the experimental data and the Guggenheim-Anderson-de Boer model was selected as the most adequate to describe the observed behavior. Addition of encapsulants affected the isotherms: at the same water activity, PP powder with added GA (PP + GA) or MD (PP + MD) presented lower equilibrium water content than pure PP and were less affected by temperature variations. Samples of PP + MD presented lower equilibrium moisture content than those of PP + GA. The isosteric heats of sorption of pulp powders with encapsulants were higher (less negative) than those of PP, suggesting that there are more active polar sites in PP than in pulp powder containing encapsulants.PRACTICAL APPLICATIONSThe choice of persimmon to carry out this work was due to the large persimmon production available in Brazil; moreover, persimmon pulp is rich in vitamin C, vitamin A and iron, as well as in phenolic compounds. Drying of fruit pulps with high sugar content presents technical difficulties because the hygroscopicity and thermoplasticity of the resulting powders when exposed to high temperature and relative humidity. For this reason, addition of high-molar-mass biopolymers, such as maltodextrin or gum arabic, is a strategy to aid drying and to improve storage stability. Knowledge of water sorption isotherms and net isosteric heats of sorption is important to various food processing operations, including drying, storage and packaging. They are useful in calculating time and energy consumptions during drying, modeling moisture changes during storage and predicting shelf life of food products.

Photoacclimation in a tropical population of Cladophora glomerata (L.) Kützing 1843 (Chlorophyta) from southeastern Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Chaotic thermalization in Yang-Mills-Higgs theory on a spacial lattice

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Experimental aspects of biomass fuels in a bubbling fluidized bed combustor

This work presents experimental information relevant to the combustion of biomass in a bubbling fluidized bed. The biomass distribution in a fluidized bed was studied through tests performed in a cold bed, while the volatiles released in the biomass pyrolysis, the burning rate of the resulting charcoal, and the combustion control regime, were studied through tests performed in a high temperature bed.Visual examination of photographs taken from a transparent walls bed, with a rectangular cross-section, showed that the large fuel particles, typical of biomass processing, were distributed in the bubbles, in the splash zone, and in the emulsion phase. The occurrence of biomass in the emulsion phase was favored by burning biomass particles of greater density and smaller size-expetimentally determined in each case. Decreasing the fuel particle size improved the biomass distribution inside the bed. The same was accomplished by increasing the superficial gas velocity as high as possible, compatibly with the acceptable elutriation.Burning tests showed that the biomass fuels have the advantage of reaching the diffusional regime at temperatures that can be lower than 1000 K, which ensures that the biomass fuels burn in a stable regime. (C) 2007 Elsevier B.V. All rights reserved.

Relaxor behavior in multiferroic BiMn2O5 ceramics

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Electron microprobe and Raman spectroscopic investigation of monazite from chromitites of Cedrolina (Goias State, Brazil)

Monazite from chromitites of Cedrolina (Goias State, Brazil) was investigated by electron microprobe and Raman spectroscopy. Monazite has been rarely encountered in chromitites. In Brazil, it was previously reported from chromitites of the Campo Formoso layered intrusion. Comparison between the two occurrences indicates similar morphology and textural characteristics, but remarkable differences in chemical composition. In both cases, monazite occurs as irregular grains (up to 200 mu m) preferentially located in the chlorite-serpentine matrix of the chromitite, more rarely included in chromite. However, the monazite from Cedrolina is characterized by higher Ce/La ratio, and Pr, Nd, Th contents, compared with the monazite from Campo Formoso. The obtained Raman spectra are very similar in the two cases, suggesting that the compositional variation of monazites and the spectral resolution of the Raman do not allow a conclusive chemical analysis with Raman spectra. Textural evidence indicates that, in both occurrences, monazite precipitation did not take place at high temperature, concomitantly with the host chromitite. In the Campo Formoso chromitites, precipitation of monazite has been related with percolation of hydrothermal, aqueous and acid fluids emanating from a granite batholith. on the contrary, the Cedrolina monazite probably formed during one of the metamorphic events that affected the area in which the host chromitite occurs.

Construção de uma célula-autoclave para medidas eletroquímicas a altas temperaturas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Ageing behavior in the Cu-10 wt.%Al and Cu-10 wt.%Al-4 wt.%Ag alloys

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of Ag additions on the activation energy for the reverse eutectoid reaction in Cu-Al alloys

The eutectoid transformation may be defined as a solid-state diffusion-controlled decomposition process of a high-temperature phase into a two-phase lamellar aggregate behind a migrating boundary on cooling below the eutectoid temperature. In substitutional solid solutions, the eutectoid reaction involves diffusion of the solute atoms either through the matrix or along the boundaries or ledges. The effect of Ag on the non-isothermal kinetics of the reverse eutectoid reaction in the Cu-9 mass%Al, Cu-10 mass%Al, and Cu-11 mass%Al alloys were studied using differential scanning calorimetry (DSC), X-ray diffraction (XRD), and scanning electron microscopy (SEM). The activation energy for this reaction was obtained using the Kissinger and Ozawa methods. The results indicated that Ag additions to Cu-Al alloys interfere on the reverse eutectoid reaction, increasing the activation energy values for the Cu-9 mass%Al and Cu-10 mass%Al alloys and decreasing these values for the Cu-11 mass%Al alloy for additions up to 6 mass%Ag. The changes in the activation energy were attributed to changes in the reaction solute and in Ag solubility due to the increase in Al content.

Corrosion and Wear Studies of Cr3C2NiCr-HVOF Coatings Sprayed on AA7050 T7 Under Cooling

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Reguladores vegetais no enraizamento e desenvolvimento de gemas de cana-de-açúcar tratadas termicamente

Este trabalho teve por finalidade estudar o efeito de reguladores vegetais sobre a emergência e desenvolvimento inicial de gemas de cana-de-açúcar 'IAC 52-150', submetidas ao tratamento térmico por via úmida. Para tanto, as gemas foram tratadas durante uma hora em soluções de ácido indolilacético (IAA) e ácido naftalenacêtico (NAA), nas concentrações de 10, 25, 50 e 100 ppm, em ácido indolbutírico (IBA) nas concentrações de 10 e 25 ppm e em água pura (testemunha). Imediatamente após o tratamento, as gemas foram plantadas em germinadores de areia. IBA 10 ppm tendeu a favorecer a emergência e o enraizamento das gemas. IAA não afetou a emergência, enraizamento e peso da parte aérea da cana-de-açúcar. Aplicação de NAA 100 ppm reduziu a porcentagem de emergência e o peso da parte aérea do cultivar IAC 52-150.