Diamond Surface Modification to Enhance Interfacial Thermal Conductivity in Al/Diamond Composites

Diamond/metal composites are very attractive materials for electronics because their excellent thermal properties make them suitable for use as heat sink elements in multifunctional electronic packaging systems. To enlarge the potential applications of these composites, current efforts are mainly focused on investigating different ways to improve the contact between metal and diamond. In the present work, a theoretical study has been carried out to determine the differences between the interfacial thermal conductance of aluminum/diamond and aluminum/graphite interfaces. Additionally, diamond particles were surface modified with oxygen to observe how it affects the quality of the diamond surface. The characterization of the surface of diamonds has been performed using different surface analysis techniques, especially x-ray photoelectron spectroscopy and temperature-programmed desorption.

MANIPULATION OF IONS, ELECTRONS, AND PHOTONS IN 2D MATERIALS BY ION INTERCALATION

2D materials have attracted tremendous attention due to their unique physical and chemical properties since the discovery of graphene. Despite these intrinsic properties, various modification methods have been applied to 2D materials that yield even more exciting results. Among all modification methods, the intercalation of 2D materials provides the highest possible doping and/or phase change to the pristine 2D materials. This doping effect highly modifies 2D materials, with extraordinary electrical transport as well as optical, thermal, magnetic, and catalytic properties, which are advantageous for optoelectronics, superconductors, thermoelectronics, catalysis and energy storage applications. To study the property changes of 2D materials, we designed and built a planar nanobattery that allows electrochemical ion intercalation in 2D materials. More importantly, this planar nanobattery enables characterization of electrical, optical and structural properties of 2D materials in situ and real time upon ion intercalation. With this device, we successfully intercalated Li-ions into few layer graphene (FLG) and ultrathin graphite, heavily dopes the graphene to 0.6 x 10^15 /cm2, which simultaneously increased its conductivity and transmittance in the visible range. The intercalated LiC6 single crystallite achieved extraordinary optoelectronic properties, in which an eight-layered Li intercalated FLG achieved transmittance of 91.7% (at 550 nm) and sheet resistance of 3 ohm/sq. We extend the research to obtain scalable, printable graphene based transparent conductors with ion intercalation. Surfactant free, printed reduced graphene oxide transparent conductor thin film with Na-ion intercalation is obtained with transmittance of 79% and sheet resistance of 300 ohm/sq (at 550 nm). The figure of merit is calculated as the best pure rGO based transparent conductors. We further improved the tunability of the reduced graphene oxide film by using two layers of CNT films to sandwich it. The tunable range of rGO film is demonstrated from 0.9 um to 10 um in wavelength. Other ions such as K-ion is also studied of its intercalation chemistry and optical properties in graphitic materials. We also used the in situ characterization tools to understand the fundamental properties and improve the performance of battery electrode materials. We investigated the Na-ion interaction with rGO by in situ Transmission electron microscopy (TEM). For the first time, we observed reversible Na metal cluster (with diameter larger than 10 nm) deposition on rGO surface, which we evidenced with atom-resolved HRTEM image of Na metal and electron diffraction pattern. This discovery leads to a porous reduced graphene oxide sodium ion battery anode with record high reversible specific capacity around 450 mAh/g at 25mA/g, a high rate performance of 200 mAh/g at 250 mA/g, and stable cycling performance up to 750 cycles. In addition, direct observation of irreversible formation of Na2O on rGO unveils the origin of commonly observed low 1st Columbic Efficiency of rGO containing electrodes. Another example for in situ characterization for battery electrode is using the planar nanobattery for 2D MoS2 crystallite. Planar nanobattery allows the intrinsic electrical conductivity measurement with single crystalline 2D battery electrode upon ion intercalation and deintercalation process, which is lacking in conventional battery characterization techniques. We discovered that with a “rapid-charging” process at the first cycle, the lithiated MoS2 undergoes a drastic resistance decrease, which in a regular lithiation process, the resistance always increases after lithiation at its final stage. This discovery leads to a 2- fold increase in specific capacity with with rapid first lithiated MoS2 composite electrode material, compare with the regular first lithiated MoS2 composite electrode material, at current density of 250 mA/g.

Synthesis of porous graphene/TiO2 by use of recycled graphite

Graphene-based nanomaterials are a kind of new technological materials with high interest for physicists, chemists and materials scientists. Graphene is a two-dimensional (2-D) sheet of carbon atoms in a hexagonal configuration with atoms bonded by sp2 bonds. These bonds and this electron configuration provides the extraordinary properties of graphene, such as very large surface area, a tunable band gap, high mechanical strength and high elasticity and thermal conductivity [1]. Graphene has also been investigated for preparation of composites with various semiconductors like TiO2, ZnO, CdS aiming at enhanced photocatalytic activity for their use for photochemical reaction as water splitting or CO2 to methanol conversion [2-3]. In this communication, the synthesis of porous graphene@TiO2 obtained from a powder graphite recycled, supplied by ECOPIBA, is presented. This graphite was exfoliated, using a nonionic surfactant (Triton X-100) and sonication. Titanium(IV) isopropoxide was used as TiO2 source. After removing the surfactant with a solution HCl/n-propanol, a porous solid is obtained with a specific area of 358 m2g-1. The solid was characterized by XRD, FTIR, XPS, EDX and TEM. Figure 1 shows the graphene 2D layer bonded with nanoparticles of TiO2. When a water suspension of this material is exposed with UV-vis radiation, water splitting reaction is carried out and H2/O2 bubbles are observed (Figure 2)

Design and fabrication of an electrode for low-actuation-voltage electrowetting-on-dielectric devices

This paper presents the design and fabrication of an electrode for low-actuation-voltage electrowetting-on-dielectric (EWOD) devices. The electrode which takes advantage of a novel shape is used to develop an EWOD device. The fabrication process for the electrode and the device development includes laser exposure, wet developing, etching, and stripping. A dielectric layer of 5% (wt./wt.) Polyvinylidene difluoride (PVDF) is used for the electrode insulation. In addition, a very thin (50 nm) layer of Teflon is coated on the EWOD surface to provide hydrophobicity. It is observed that a thin and high dielectric-constant layer can reduce the actuation voltage in the EWOD device. An actuation voltage of 14.8 V was achieved by the EWOD device.

Reducing electrowetting-on-dielectric actuation voltage using a novel electrode shape and a multi-layer dielectric coating

This paper presents design and fabrication of an electrowetting-on-dielectric (EWOD) device using a novel electrode shape and a multi-layer dielectric coating that reduce the actuation voltage of the device to less than 12.6 V. The fabrication of the EWOD electrodes is carried out in several steps including laser exposure, wet developing, etching, and stripping. A high-dielectric-constant multi-layer dielectric coating containing a 770 nm thick Polyvinylidene difluoride (PVDF) layer and a 1 µm thick Cyanoethyl pullulan (CEP) layer, is deposited on the EWOD electrodes for insulation. This multi-layer dielectric structure exhibits a high capacitance per unit area, and the novel electrode shape changes the actuation force at the droplet contact line reducing the voltage required to operate the device. In addition, an overlaying Teflon layer of 50 nm is placed on top of the dielectric structure to provide a hydrophobic surface for droplet manipulation. It is observed from the experiments that the electrode shape and the dielectric structure have contributed to the reduction of the actuation voltage of the EWOD device.

Well-controlled preparation of evenly distributed nanoporous HOPG surface via diazonium salt assisted electrochemical etching process

Evenly distributed nanoporous highly oriented pyrolytic graphite (HOPG) surfaces with controllable pore size were successfully prepared via diazonium salt assisted electrochemical etching method. The porous HOPG was investigated by atomic force microscopy (AFM), Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS) Raman spectroscopy and X-ray diffraction. The size of these pores can be tuned by manipulating the electrochemical etching time. These porous HOPG substrates also demonstrated the enhanced electrocatalytical behaviour and were employed as benign arena for the immobilization of Ru(bpy)32+ for electrochemiluminescence (ECL) sensing applications.

Effect of surface conditions on flow of a micropolar fluid driven by a porous stretching sheet

-

Some surface profiles of a strip after plane-strain indentation by rigid bodies with serrated surfaces

This paper is concerned with the surface profiles of a strip after rigid bodies with serrated (saw-teeth) surfaces indent the strip and are subsequently removed. Plane-strain conditions are assumed. This has application in roughness transfer of final metal forming process. The effects of the semi-angle of the teeth, the depth of indentation and the friction on the contact surface on the profile are considered.