Impacte da nova regulamentação na certificação energética de edifícios

Dissertação de Mestrado, Engenharia Civil, Especialização em Construção, Instituto Superior de Engenharia, Universidade do Algarve, 2016

Uma janela tropical: análise do desempenho luminoso de ambientes com aberturas sombreadas para o clima de Natal/RN

This master thesis introduces assessment procedures of daylighting performance in office rooms with shaded opening, recommendations for Natal-RN (Latitude 05,47' S, Longitude 35,11' W). The studies assume the need of window exterior shading in hot and humid climate buildings. The daylighting performance analyses are based on simulated results for three levels of illuminance (300,500 e 1000 lux) between 08h00 e 16h00, in rooms with 2,80 m height, 6 m large and 4 m, 6 m e 8 m depths, with a centered single opening, window wall ratio (20%, 40% e 60%), four orientations (North, East, South and West), and two types of sky (clear and partially cloudy). The sky characteristics were statistically determined based on hourly data from INPE-CRN solar and daylighting weather station. The lighting performance is resulted from dynamic computer simulation of 72 models using Troplux 3.12. The simulation results were assessed using a new parameter to quantify the use of interior daylighting, the useful percentage of daylight (PULN), which corresponds to the time fraction with satisfactory light, in accordance with the illuminance design. The passive zone depths are defined based on the PULN. Despite the failures of illuminance data from the weather station, the analyses ratified the high potential of daylighting for shaded rooms. The most influential variables on the lighting performance are the opening size and the illuminance of design, while the orientation is a little influential

Primeiras aproximações de uma análise do financiamento da política nacional de esporte e lazer no Governo Lula

Este artigo realiza uma análise introdutória sobre o gasto público referente às políticas de esporte e lazer no Governo Lula. Os dados coletados apresentaram uma distribuição instável entre os programas, o que impede o estabelecimento de um padrão de financiamento para o esporte e lazer durante o período analisado (2003-2010), bem como de afirmar a existência de programas e/ou frações de classes hegemônicas no que tange aos gastos públicos do setor. Todavia, algumas particularidades indicam a razoabilidade do pressuposto sobre a priorização do esporte de alto rendimento dentro da alocação dos recursos públicos destinados ao financiamento da Política Nacional de Esporte e Lazer (PNEL) do Governo Lula. __________________________________________________________________________________________________ ABSTRACT

Compostos bioativos de microalgas com interesse no tratamento da diabetes

Dissertação de Mestrado, Biologia Molecular e Microbiana, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2016

Efeito residual da aplicação de biosólido na cultura do milho.

EFEITO RESIDUAL DA APLICAÇÃO DE BIOSÓLIDO NA CULTURA DO MILHO. MA039 Fernanda Ardilha dos Santos1; Fernanda Gonçalves Serrenho1; Germana Breves Rona1; Sarai de Alcantara1; Daniel Vidal Perez2; Wagner Bettiol3 ; Waldemore Moriconi3, fernanda.ardilha@oi.com.br (1) Instituto de Química, UFRJ, (2) Embrapa Solos, RJ, (3) Embrapa Meio Ambiente (INTRODUÇÃO) A operação de uma Estação de Tratamento de Esgoto visa diminuir a carga poluente que seria lançada nos corpos receptores. Porém um novo problema é gerado: a disposição do lodo de esgoto, ou biossólido. Uma opção seria a disposição em aterro sanitário, que agrava ainda mais o problema de manejo do lixo urbano. Uma alternativa razoável seria a sua utilização como condicionador de solo e/ou fertilizantes, já que o biossólido promove a reciclagem de matéria orgânica e nutrientes. Entretanto, metais pesados são facilmente encontrados na composição de um biossólido. A utilização desse material para fins agrícolas pode causar alterações nos teores desses metais e na sua dispersão, tanto na fase sólida quanto na líquida do solo, com conseqüências ainda pouco conhecidas para nossas condições. O objetivo deste trabalho é estudar o impacto causado pelo uso agrícola do biossólido, de origem doméstica/industrial, nos teores e na evolução dos elementos Mn, Zn, Cu, Ni, Cd e Cr. (METODOLOGIA) A área experimental situou-se em Jaguariúna (SP), em Latossolo Vermelho Distroférrico (textura argilosa). O delineamento experimental escolhido foi o de fatorial (2 x 6) em blocos ao acaso, com 3 repetições, em que um tratamento correspondeu a uma dose aplicada, antes do plantio de milho, do lodo de esgoto. Os tratamentos estudados constaram de uma Testemunha Absoluta, Testemunha convencional (NPK), 1, 2, 4 e 8 vezes a dose de lodo de esgoto, calculada com base na adubação de N, requerida pela cultura do milho. O outro tratamento se refere ao tipo de lodo de esgoto utilizado, que foi fornecido pela SABESP, a saber: Barueri (Industrial) e de Franca (Doméstico), em SP. A amostragem ocorreu em novembro de 2004,2005,2006 e 2007 sendo a profundidade de coleta de 0-20cm. A técnica de extração seqüencial utilizada foi a descrita por Wasserman et al. (2005). As determinações analíticas dos metais estudados foram realizadas por ICP-OES(PE OPTIMA 3000). (RESULTADOS) Para o Zn, com o aumento da dose aplicada, observa-se um aumento significativo na concentração das fases 1e 2 e em menor grau na fase 5. Para o Cu observa-se um aumento na concentração de todas as frações em função do aumento da dose aplicada de lodo sendo a fase 5 desprezível. Nota-se que, apesar da tendência do Cu formar complexos com a matéria orgânica, é a fase 2 a mais representativa, sendo que a fase 1 apresenta alguma importância nas doses mais elevadas. O Cr sofreu um aumento na concentração total com o aumento da dose de lodo aplicada, apresentando um incremento nas concentrações de todas as fases exceto a fase 5. Todas as concentrações totais dos elementos estudados aumentaram em função do aumento das doses de lodo aplicadas. Vale ressaltar que o ano de 2003 foi o último onde houve aplicação do biossólido. Portanto, a amostragem feita em 2006 já se refere a um estudo de atenuação natural. Ademais, os resultados são relativos a aplicação do lodo de Barueri já que este apresenta concentrações metálicas mais elevadas e o comportamento dos elementos são semelhantes para distintoas fontes de lodo. (CONCLUSÃO) As concentrações nas fases aumentaram em função do aumento da concentração de lodo utilizada. As fases 1 e 2 apresentam importância neste sentido sendo este um motivo de grande preocupação, por serem frações biodisponíveis, podendo agravar seriamente, os riscos de contaminação pelos metais em questão. No entanto, as concentrações encontradas são bem menores que aquelas recomendadas pela CONAMA no375/2006 . Isto indica que a utilização do lodo oriundo das ETES na agricultura é uma solução bastante viável para sua disposição final, sendo uma prática já adotada em vários países (Ludivice et al, 2000). Agradecimentos: CNPq, FAPERJ, FUJB, EMBRAPA

Multibiomarker assessment of cadmium-based quantum dots effects in the marine mussel Mytilus galloprovincialis

Tese de Doutoramento, Ciências do Mar, da Terra e do Ambiente, Ramo: Ciências e Tecnologias do Ambiente, Especialização em Ecotoxicologia, Faculdade de Ciências e Tecnologia, Universidade do Algarve, 2016

Infravermelho na caracterização de ácidos húmicos de latossolo sob efeito de uso contínuo de lodo de esgoto.

Objetivou-se caracterizar, por meio de espectroscopia no infravermelho com transformada de Fourier (IVTF), possíveis mudanças na natureza química de ácidos húmicos (AHs) extraídos de amostras de Latossolo (0?10 cm) do Campo Experimental da Embrapa Meio Ambiente, em Jaguariúna (SP). Os dados foram obtidos após seis cultivos de milho e a aplicação de doses variáveis de lodo de esgoto de Barueri (LB) (base seca), conforme os tratamentos avaliados: LB0, LB1, LB2, LB4 e LB8 sendo 0, 1, 2, 4 e 8 vezes a necessidade de N para o milho, correspondendo a 0, 30, 60, 120 e 240 t ha-1. Como referência, foi amostrada uma área sob mata. Foram obtidos espectros de ácidos húmicos e do lodo de esgoto utilizado no experimento, e calculados os índices de hidrofobicidade (IH) e de condensação (IC) nas amostras de ácidos húmicos. Foram notadas pequenas alterações na natureza química de AHs de áreas tratadas com lodo de esgoto, em relação à testemunha. Os AHs apresentam grupos aromáticos, -OH fenólicos, - COOH, estruturas alifáticas, carboidratos e impurezas minerais. O uso contínuo de elevadas doses de LB reduziu a concentração de C-alifático e o grau de condensação dos ácidos húmicos, o que sinaliza que há frações orgânicas com maior biodisponibilidade no solo. Na área de mata, o material húmico se caracteriza pelo caráter hidrofóbico e pelo baixo grau de condensação.

Efeito da Gália como aditivo de sinterização em eletrólitos cerâmicos à base de céria sintetizados pelo método de complexação de cátions

Fuel cells are considered one of the most promising ways of converting electrical energy due to its high yield and by using hydrogen (as fuel) which is considered one of the most important source of clean energy for the future. Rare earths doped ceria has been widely investigated as an alternative material for the electrolyte of solid oxide fuel cells (SOFCs) due to its high ionic conductivity at low operating temperatures compared with the traditional electrolytes based on stabilized zirconia. This work investigates the effect of gallium oxide (Gallia) as a sintering aid in Eu doped ceria ceramic electrolytes since this effect has already been investigated for Gd, Sm and Y doped ceria electrolytes. The desired goal with the use of a sintering aid is to reduce the sintering temperature aiming to produce dense ceramics. In this study we investigated the effects on densification, microstructure and ionic conduction caused by different molar fraction of the dopants europium (10, 15 and 20%) and gallium oxide (0.3, 0.6 and 0.9%) in samples sintered at 1300, 1350 and 1450 0 C. Samaria (10 and 20%) doped ceria samples sintered between 1350 and 1450 °C were used as reference. Samples were synthesized using the cation complexation method. The ceramics powders were characterized by XRF, XRD and SEM, while the sintered samples were investigated by its relative density, SEM and impedance spectroscopy. It was showed that gallia contents up to 0.6% act as excellent sintering aids in Eu doped ceria. Above this aid content, gallia addition does not promote significant increase in density of the ceramics. In Ga free samples the larger densification were accomplished with Eu 15% molar, effect expressed in the microstructure with higher grain growth although reduced and surrounded by many open pores. Relative densities greater than 95 % were obtained by sintering between 1300 and 1350 °C against the usual range 1500 - 1600 0 C. Samples containing 10% of Sm and 0.9% of Ga reached 96% of theoretical density by sintering at 1350 0 C for 3h, a gain compared to 97% achieved with 20% of Sm and 1% of Ga co-doped cerias sintered at 1450 0 C for 24 h as described in the literature. It is found that the addition of gallia in the Eu doped ceria has a positive effect on the grain conductivity and a negative one in the grain boundary conductivity resulting in a small decrease in the total conductivity which will not compromise its application as sintering aids in ceria based electrolytes. Typical total conductivity values at 600 and 700 °C, around 10 and 30 mS.cm -1 respectively were reached in this study. Samples with 15% of Eu and 0.9 % of Ga sintered at 1300 and 1350 °C showed relative densities greater than 96% and total conductivity (measured at 700 °C) between 20 and 33 mS.cm -1 . The simultaneous sintering of the electrolyte with the anode is one of the goals of research in materials for SOFCs. The results obtained in this study suggest that dense Eu and Ga co-doped ceria electrolytes with good ionic conductivity can be sintered simultaneously with the anode at temperatures below 1350 °C, the usual temperature for firing porous anode materials

Aplicação da metodologia de planejamento de experimentos para formulação de massas cerâmicas para telhas

Rio Grande do Norte State stands out as one great producer of structural clay of the brazilian northeastern. The Valley Assu ceramic tiles production stands out obtained from ilitics ball clays that abound in the region under study. Ceramics formulation and the design of experiments with mixture approach, has been applied for researchers, come as an important aid to decrease the number of experiments necessary to the optimization. In this context, the objective of this work is to evaluate the effects of the formulation, temperature and heating rate in the physical-mechanical properties of the red ceramic body used for roofing tile fabrication of the Valley Assu, using design of mixture experiments. Four clays samples used in two ceramics industry of the region were use as raw material and characterized by X-ray diffraction, chemical composition, differential thermal analysis (DTA), thermogravimetric analysis (TGA), particle size distribution analysis and plasticity techniques. Afterwards, they were defined initial molded bodies and made specimens were then prepared by uniaxial pressing at 25 MPa before firing at 850, 950 and 1050 ºC in a laboratory furnace, with heating rate in the proportions of 5, 10 e 15 ºC/min. The following tecnologicals properties were evaluated: linear firing shrinkage, water absorption and flexural strength. Results show that the temperature 1050 ºC and heating rate of 5 ºC/min was the best condition, therefore presented significance in all physical-mechanical properties. The model was accepted as valid based of the production of three new formulations with fractions mass diferents of the initial molded bodies and heated with temperature at 1050 ºC and heating rate of 5 ºC/min. Considering the formulation, temperature and heating rate as variables of the equations, another model was suggested, where from the aplication of design of experiments with mixtures was possible to get a best formulation, whose experimental error is the minor in relation to the too much formulations

Aplicação de termogravimetria acoplada à espectrometria de massas para caracterização de petróleo e determinação da curva de evolução de gás sulfídrico

With the new discoveries of oil and gas, the exploration of fields in various geological basins, imports of other oils and the development of alternative fuels, more and more research labs have evaluated and characterized new types of petroleum and derivatives. Therefore the investment in new techniques and equipment in the samples analysis to determine their physical and chemical properties, their composition, possible contaminants, especification of products, among others, have multiplied in last years, so development of techniques for rapid and efficient characterization is extremely important for a better economic recovery of oil. Based on this context, this work has two main objectives. The first one is to characterize the oil by thermogravimetry coupled with mass spectrometry (TG-MS), and correlate these results with from other types of characterizations data previously informed. The second is to use the technique to develop a methodology to obtain the curve of evaluation of hydrogen sulfide gas in oil. Thus, four samples were analyzed by TG-MS, and X-ray fluorescence spectrometry (XRF). TG results can be used to indicate the nature of oil, its tendency in coke formation, temperatures of distillation and cracking, and other features. It was observed in MS evaluations the behavior of oil main compounds with temperature, the points where the volatilized certain fractions and the evaluation gas analysis of sulfide hydrogen that is compared with the evaluation curve obtained by Petrobras with another methodology

Caracterização ambiental de bancos areno-lamosos nos campos petrolíferos de Macau e Serra (RN), como subsídio às medidas mitigadoras ao processo erosivo

On Rio Grande do Norte northern coast the process of sediment transport are intensely controlled by wind and sea (waves and currents) action, causing erosion and shoreline morphological instability. Due to the importance of such coastal zone it was realized the multi-spectral mapping and physical-chemical characterization of mudflats and mangroves aiming to support the mitigating actions related to the containment of the erosive process on the oil fields of Macau and Serra installed at the study area. The multi-spectral bands of 2000 and 2008 LANDSAT 5 TM images were submitted on the several digital processing steps and RGB color compositions integrating spectral bands and Principal Components. Such processing methodology was important to the mapping of different units on surface, together with field works. It was possible to make an analogy of the spectral characteristics of wetlands with vegetations areas (mangrove), showing the possibility to make a restoration of this area, contributing with the environmental monitoring of that ecosystem. The maps of several units were integrated in GIS environment at 1:60,000 scale, including the classification of features according to the presence or absence of vegetation cover. Thus, the strategy of methodology established that there are 10.13 km2 at least of sandy-muddy and of these approximately 0.89 km2 with the possibility to be used in a reforestation of typical flora of mangrove. The physical-chemical characterization showed areas with potential to introduce local species of mangrove and they had a pH above neutral with a mean of 8.4. The characteristic particle size is sand in the fine fractions, the high levels of carbonate, organic matter and major and trace element in general are concentrated where the sediment had the less particles size, showing the high correlation that those elements have with smaller particles of sediment. The application of that methodological strategy is relevant to the better understanding of features behavior and physical-chemical data of sediment samples collected on field allow the analysis of efficiency/capability of sandy-muddy to reforestation with local mangrove species for mitigation of the erosive action and coastal processes on the areas occupied by the oil industry

Conversão térmica e termocatalítica à baixa temperatura do óleo de girassol para obtenção de bio-óleo

The use of biofuels remotes to the eighteenth century, when Rudolf Diesel made the first trials using peanut oil as fuel in a compression ignition engine. Based on these trials, there was the need for some chemical change to vegetable oil. Among these chemical transformations, we can mention the cracking and transesterification. This work aims at conducting a study using the thermocatalytic and thermal cracking of sunflower oil, using the Al-MCM-41 catalyst. The material type mesoporous Al-MCM-41 was synthesized and characterized by Hydrothermical methods of X-ray diffraction, scanning electron microscopy, nitrogen adsorption, absorption spectroscopy in the infrared and thermal gravimetric analysis (TG / DTG).The study was conducted on the thermogravimetric behavior of sunflower oil on the mesoporous catalyst cited. Activation energy, conversion, and oil degradation as a function of temperature were estimated based on the integral curves of thermogravimetric analysis and the kinetic method of Vyazovkin. The mesoporous material Al-MCM-41 showed one-dimensional hexagonal formation. The study of the kinetic behavior of sunflower oil with the catalyst showed a lower activation energy against the activation energy of pure sunflower oil. Two liquid fractions of sunflower oil were obtained, both in thermal and thermocatalytic pyrolisis. The first fraction obtained was called bio-oil and the second fraction obtained was called acid fraction. The acid fraction collected, in thermal and thermocatalytic pyrolisis, showed very high level of acidity, which is why it was called acid fraction. The first fraction was collected bio-called because it presented results in the range similar to petroleum diesel

Estudo de modelos composicionais de óleo na injeção contínua de vapor

The objective of the thermal recovery is to heat the resevoir and the oil in it to increase its recovery. In the Potiguar river basin there are located several heavy oil reservoirs whose primary recovery energy provides us with a little oil flow, which makes these reservoirs great candidates for application of a method of recovery advanced of the oil, especially the thermal. The steam injection can occur on a cyclical or continuous manner. The continuous steam injection occurs through injection wells, which in its vicinity form a zone of steam that expands itself, having as a consequence the displace of the oil with viscosity and mobility improved towards the producing wells. Another possible mechanism of displacement of oil in reservoirs subjected to continuous injection of steam is the distillation of oil by steam, which at high temperatures; their lighter fractions can be vaporized by changing the composition of the oil produced, of the oil residual or to shatter in the amount of oil produced. In this context, this paper aims to study the influence of compositional models in the continuous injection of steam through in the analysis of some parameters such as flow injection steam and temperature of injection. Were made various leading comparative analysis taking the various models of fluid, varying from a good elementary, with 03 pseudocomponents to a modeling of fluids with increasing numbers of pseudocomponents. A commercial numerical simulator was used for the study from a homogeneous reservoir model with similar features to those found in northeastern Brazil. Some conclusions as the increasing of the simulation time with increasing number of pseudocomponents, the significant influence of flow injection on cumulative production of oil and little influence of the number of pseudocomponents in the flows and cumulative production of oil were found

Avaliação da correlação entre os parâmetros, carbono orgânico total e elementos tóxicos, em solo de um posto de serviço e revenda de combustíveis

Today a major responsibility for the contamination of soil and groundwater and surface water are establishments known as gas stations of fuel which has attracted increasing attention from both the general population as the state agencies of environmental control due to leaks in storage tanks and mainly to disruption of pipe corrosion of tanks and pumping. Other services, like oil changes and car wash are also causes for concern in this type of establishment. These leaks can cause or waste produced, and the contamination of aquifers, serious health problems and public safety, since most of these stations located in urban areas. Based on this, the work was to evaluate soil contamination of a particular service station and fuel sales in the city of Natal, through the quantification of heavy metals like Cd, Cu, Cr, Ni, Pb, Zn of total organic carbon (TOC) and organic matter using different techniques such as optical emission spectrometry with inductively coupled plasma source (ICP OES), Total Organic Carbon analyzer and gravimetric analysis respectively. And also to characterize the soil through particle size analysis. Samples were taken in 21 georeferenced points and collected in the same period. The soils sampled in sampling stations P3, P5, P6, P10, P11, P12, P13, P14, P15, P17, P18 and P20 showed the smallest size fractions ranging from fine sand to medium sand. The other study sites ranged from fine sand to medium sand, except the point P8 showed that only the type size medium sand and P19, indicating a particle size of the coarse type. The small correlation of organic matter with the elements studied in this work suggests that these are not of anthropogenic origin but geochemical support

Análise paramétrica da injeção de vapor e solvente em reservatórios de óleo pesado

A significant fraction of the hydrocarbon reserves in the world is formed by heavy oils. From the thermal methods used to recovery these resources, Steamflooding has been one of the main economically viable alternatives. In Brazil, this technology is widely used by Petrobras in Northeast fields. Latent heat carried by steam heats the oil in the reservoir, reducing its viscosity and facilitating the production. In the last years, an alternative more and more used by the oil industry to increase the efficiency of this mechanism has been the addition of solvents. When co-injected with steam, the vaporized solvent condenses in the cooler regions of the reservoir and mixes with the oil, creating a low viscosity zone between the steam and the heavy oil. The mobility of the displaced fluid is then improved, resulting in an increase of oil recovery. To better understand this improved oil recovery method and investigate its applicability in reservoirs with properties similar to those found in Potiguar Basin, a numerical study was done to analyze the influence of some operational parameters (steam injection rate, injected solvent volume and solvent type) on oil recovery. Simulations were performed in STARS ("Steam, Thermal, and Advanced Processes Reservoir Simulator"), a CMG ("Computer Modelling Group") program, version 2009.10. It was found that solvents addition to the injected steam not only anticipated the heated oil bank arrival to the producer well, but also increased the oil recovery. Lower cold water equivalent volumes were required to achieve the same oil recoveries from the models that injected only steam. Furthermore, much of the injected solvent was produced with the oil from the reservoir