Driving assistance system applied in curves for real vehicles | Sistema de ayuda a la conducción en curvas para vehículos reales

Decreasing the accidents on highway and urban environments is the main motivation for the research and developing of driving assistance systems, also called ADAS (Advanced Driver Assistance Systems). In recent years, there are many applications of these systems in commercial vehicles: ABS systems, Cruise Control (CC), parking assistance and warning systems (including GPS), among others. However, the implementation of driving assistance systems on the steering wheel is more limited, because of their complexity and sensitivity. This paper is focused in the development, test and implementation of a driver assistance system for controlling the steering wheel in curve zones. This system is divided in two levels: an inner control loop which permits to execute the position and speed target, softening the action over the steering wheel, and a second control outer loop (controlling for fuzzy logic) that sends the reference to the inner loop according the environment and vehicle conditions. The tests have been done in different curves and speeds. The system has been proved in a commercial vehicle with satisfactory results.

Ultrasonic sensors in urban traffic driving-aid systems

Currently, vehicles are often equipped with active safety systems to reduce the risk of accidents, most of which occur in urban environments. The most prominent include Antilock Braking Systems (ABS), Traction Control and Stability Control. All these systems use different kinds of sensors to constantly monitor the conditions of the vehicle, and act in an emergency. In this paper the use of ultrasonic sensors in active safety systems for urban traffic is proposed, and the advantages and disadvantages when compared to other sensors are discussed. Adaptive Cruise Control (ACC) for urban traffic based on ultrasounds is presented as an application example. The proposed system has been implemented in a fully-automated prototype vehicle and has been tested under real traffic conditions. The results confirm the good performance of ultrasonic sensors in these systems. ©2011 by the authors.

Lenticular arrays based on liquid crystals

Lenticular array products have experienced a growing interest in the last decade due to the very wide range of applications they can cover. Indeed, this kind of lenses can create different effects on a viewing image such as 3D, flips, zoom, etc. In this sense, lenticular based on liquid crystals (LC) technology is being developed with the aim of tuning the lens profiles simply by controlling the birefringence electrically. In this work, a LC lenticular lens array has been proposed to mimic a GRIN lenticular lens array but adding the capability of tuning their lens profiles. Comb control electrodes have been designed as pattern masks for the ITO on the upper substrate. Suitable high resistivity layers have been chosen to be deposited on the control electrode generating an electric field gradient between teeth of the same electrode. Test measurements have allowed us to demonstrate that values of phase retardations and focal lengths, for an optimal driving waveform, are fairly in agreement. In addition, results of focusing power of tuneable lenses were compared to those of conventional lenses. The behaviour of both kinds of lenses has revealed to be mutually similar for focusing collimated light and for refracting images.

A silviculture-oriented spatio-temporal model for germination in Pinus pinea L. in the Spanish Northern Plateau based on a direct seeding experiment

Natural regeneration in Pinus pinea stands commonly fails throughout the Spanish Northern Plateau under current intensive regeneration treatments. As a result, extensive direct seeding is commonly conducted to guarantee regeneration occurrence. In a period of rationalization of the resources devoted to forest management, this kind of techniques may become unaffordable. Given that the climatic and stand factors driving germination remain unknown, tools are required to understand the process and temper the use of direct seeding. In this study, the spatio-temporal pattern of germination of P. pinea was modelled with those purposes. The resulting findings will allow us to (1) determine the main ecological variables involved in germination in the species and (2) infer adequate silvicultural alternatives. The modelling approach focuses on covariates which are readily available to forest managers. A two-step nonlinear mixed model was fitted to predict germination occurrence and abundance in P. pinea under varying climatic, environmental and stand conditions, based on a germination data set covering a 5-year period. The results obtained reveal that the process is primarily driven by climate variables. Favourable conditions for germination commonly occur in fall although the optimum window is often narrow and may not occur at all in some years. At spatial level, it would appear that germination is facilitated by high stand densities, suggesting that current felling intensity should be reduced. In accordance with other studies on P. pinea dispersal, it seems that denser stands during the regeneration period will reduce the present dependence on direct seeding.

Unit Root Analysis of Traffic Time Series in Toll Highways

Concession contracts in highways often include some kind of clauses (for example, a minimum traffic guarantee) that allow for better management of the business risks. The value of these clauses may be important and should be added to the total value of the concession. However, in these cases, traditional valuation techniques, like the NPV (net present value) of the project, are insufficient. An alternative methodology for the valuation of highway concession is one based on the real options approach. This methodology is generally built on the assumption of the evolution of traffic volume as a GBM (geometric Brownian motion), which is the hypothesis analyzed in this paper. First, a description of the methodology used for the analysis of the existence of unit roots (i.e., the hypothesis of non-stationarity) is provided. The Dickey-Fuller approach has been used, which is the most common test for this kind of analysis. Then this methodology is applied to perform a statistical analysis of traffic series in Spanish toll highways. For this purpose, data on the AADT (annual average daily traffic) on a set of highways have been used. The period of analysis is around thirty years in most cases. The main outcome of the research is that the hypothesis that traffic volume follows a GBM process in Spanish toll highways cannot be rejected. This result is robust, and therefore it can be used as a starting point for the application of the real options theory to assess toll highway concessions.

Mechanical actuator for biomimetic propulsion and the effect of the caudal fin elasticity on the swimming performance

This paper presents a mechanical actuator for the biomimetic propulsion of swimming devices and the experimental study of the effect of the caudal fin elasticity on the overall performance. The design of the proposed drive allows the DC motor to operate at constant speed, so all the power of the motor is spent only for the motion of the caudal fin. A prototype of the actuator, in which the caudal fin serves as a driving element, is manufactured and tested in both laboratory and natural conditions. The swimming speed, the thrust efficiency and the maneuverability are evaluated for caudal fins with different stiffness. The caudal fin whose rigidity varies relative to both vertical and horizontal cross-section, exhibits the best performance. The achieved results also confirm that the proposed actuator could be of great interest to applications in the field of underwater operation, ocean investigation and environmental protection.

Traffic jam driving with NMV avoidance

n recent years, the development of advanced driver assistance systems (ADAS) – mainly based on lidar and cameras – has considerably improved the safety of driving in urban environments. These systems provide warning signals for the driver in the case that any unexpected traffic circumstance is detected. The next step is to develop systems capable not only of warning the driver but also of taking over control of the car to avoid a potential collision. In the present communication, a system capable of autonomously avoiding collisions in traffic jam situations is presented. First, a perception system was developed for urban situations—in which not only vehicles have to be considered, but also pedestrians and other non-motor-vehicles (NMV). It comprises a differential global positioning system (DGPS) and wireless communication for vehicle detection, and an ultrasound sensor for NMV detection. Then, the vehicle's actuators – brake and throttle pedals – were modified to permit autonomous control. Finally, a fuzzy logic controller was implemented capable of analyzing the information provided by the perception system and of sending control commands to the vehicle's actuators so as to avoid accidents. The feasibility of the integrated system was tested by mounting it in a commercial vehicle, with the results being encouraging.

Multiple Input-Output Bidirectional Solid State Transformer Based on a Series Resonant Converter

Las fuentes de alimentación de modo conmutado (SMPS en sus siglas en inglés) se utilizan ampliamente en una gran variedad de aplicaciones. La tarea más difícil para los diseñadores de SMPS consiste en lograr simultáneamente la operación del convertidor con alto rendimiento y alta densidad de energía. El tamaño y el peso de un convertidor de potencia está dominado por los componentes pasivos, ya que estos elementos son normalmente más grandes y más pesados que otros elementos en el circuito. Para una potencia de salida dada, la cantidad de energía almacenada en el convertidor que ha de ser entregada a la carga en cada ciclo de conmutación, es inversamente proporcional a la frecuencia de conmutación del convertidor. Por lo tanto, el aumento de la frecuencia de conmutación se considera un medio para lograr soluciones más compactas con los niveles de densidad de potencia más altos. La importancia de investigar en el rango de alta frecuencia de conmutación radica en todos los beneficios que se pueden lograr: además de la reducción en el tamaño de los componentes pasivos, el aumento de la frecuencia de conmutación puede mejorar significativamente prestaciones dinámicas de convertidores de potencia. Almacenamiento de energía pequeña y el período de conmutación corto conducen a una respuesta transitoria del convertidor más rápida en presencia de las variaciones de la tensión de entrada o de la carga. Las limitaciones más importantes del incremento de la frecuencia de conmutación se relacionan con mayores pérdidas del núcleo magnético convencional, así como las pérdidas de los devanados debido a los efectos pelicular y proximidad. También, un problema potencial es el aumento de los efectos de los elementos parásitos de los componentes magnéticos - inductancia de dispersión y la capacidad entre los devanados - que causan pérdidas adicionales debido a las corrientes no deseadas. Otro factor limitante supone el incremento de las pérdidas de conmutación y el aumento de la influencia de los elementos parásitos (pistas de circuitos impresos, interconexiones y empaquetado) en el comportamiento del circuito. El uso de topologías resonantes puede abordar estos problemas mediante el uso de las técnicas de conmutaciones suaves para reducir las pérdidas de conmutación incorporando los parásitos en los elementos del circuito. Sin embargo, las mejoras de rendimiento se reducen significativamente debido a las corrientes circulantes cuando el convertidor opera fuera de las condiciones de funcionamiento nominales. A medida que la tensión de entrada o la carga cambian las corrientes circulantes incrementan en comparación con aquellos en condiciones de funcionamiento nominales. Se pueden obtener muchos beneficios potenciales de la operación de convertidores resonantes a más alta frecuencia si se emplean en aplicaciones con condiciones de tensión de entrada favorables como las que se encuentran en las arquitecturas de potencia distribuidas. La regulación de la carga y en particular la regulación de la tensión de entrada reducen tanto la densidad de potencia del convertidor como el rendimiento. Debido a la relativamente constante tensión de bus que se encuentra en arquitecturas de potencia distribuidas los convertidores resonantes son adecuados para el uso en convertidores de tipo bus (transformadores cc/cc de estado sólido). En el mercado ya están disponibles productos comerciales de transformadores cc/cc de dos puertos que tienen muy alta densidad de potencia y alto rendimiento se basan en convertidor resonante serie que opera justo en la frecuencia de resonancia y en el orden de los megahercios. Sin embargo, las mejoras futuras en el rendimiento de las arquitecturas de potencia se esperan que vengan del uso de dos o más buses de distribución de baja tensión en vez de una sola. Teniendo eso en cuenta, el objetivo principal de esta tesis es aplicar el concepto del convertidor resonante serie que funciona en su punto óptimo en un nuevo transformador cc/cc bidireccional de puertos múltiples para atender las necesidades futuras de las arquitecturas de potencia. El nuevo transformador cc/cc bidireccional de puertos múltiples se basa en la topología de convertidor resonante serie y reduce a sólo uno el número de componentes magnéticos. Conmutaciones suaves de los interruptores hacen que sea posible la operación en las altas frecuencias de conmutación para alcanzar altas densidades de potencia. Los problemas posibles con respecto a inductancias parásitas se eliminan, ya que se absorben en los Resumen elementos del circuito. El convertidor se caracteriza con una muy buena regulación de la carga propia y cruzada debido a sus pequeñas impedancias de salida intrínsecas. El transformador cc/cc de puertos múltiples opera a una frecuencia de conmutación fija y sin regulación de la tensión de entrada. En esta tesis se analiza de forma teórica y en profundidad el funcionamiento y el diseño de la topología y del transformador, modelándolos en detalle para poder optimizar su diseño. Los resultados experimentales obtenidos se corresponden con gran exactitud a aquellos proporcionados por los modelos. El efecto de los elementos parásitos son críticos y afectan a diferentes aspectos del convertidor, regulación de la tensión de salida, pérdidas de conducción, regulación cruzada, etc. También se obtienen los criterios de diseño para seleccionar los valores de los condensadores de resonancia para lograr diferentes objetivos de diseño, tales como pérdidas de conducción mínimas, la eliminación de la regulación cruzada o conmutación en apagado con corriente cero en plena carga de todos los puentes secundarios. Las conmutaciones en encendido con tensión cero en todos los interruptores se consiguen ajustando el entrehierro para obtener una inductancia magnetizante finita en el transformador. Se propone, además, un cambio en los señales de disparo para conseguir que la operación con conmutaciones en apagado con corriente cero de todos los puentes secundarios sea independiente de la variación de la carga y de las tolerancias de los condensadores resonantes. La viabilidad de la topología propuesta se verifica a través una extensa tarea de simulación y el trabajo experimental. La optimización del diseño del transformador de alta frecuencia también se aborda en este trabajo, ya que es el componente más voluminoso en el convertidor. El impacto de de la duración del tiempo muerto y el tamaño del entrehierro en el rendimiento del convertidor se analizan en un ejemplo de diseño de transformador cc/cc de tres puertos y cientos de vatios de potencia. En la parte final de esta investigación se considera la implementación y el análisis de las prestaciones de un transformador cc/cc de cuatro puertos para una aplicación de muy baja tensión y de decenas de vatios de potencia, y sin requisitos de aislamiento. Abstract Recently, switch mode power supplies (SMPS) have been used in a great variety of applications. The most challenging issue for designers of SMPS is to achieve simultaneously high efficiency operation at high power density. The size and weight of a power converter is dominated by the passive components since these elements are normally larger and heavier than other elements in the circuit. If the output power is constant, the stored amount of energy in the converter which is to be delivered to the load in each switching cycle is inversely proportional to the converter’s switching frequency. Therefore, increasing the switching frequency is considered a mean to achieve more compact solutions at higher power density levels. The importance of investigation in high switching frequency range comes from all the benefits that can be achieved. Besides the reduction in size of passive components, increasing switching frequency can significantly improve dynamic performances of power converters. Small energy storage and short switching period lead to faster transient response of the converter against the input voltage and load variations. The most important limitations for pushing up the switching frequency are related to increased conventional magnetic core loss as well as the winding loss due to the skin and proximity effect. A potential problem is also increased magnetic parasitics – leakage inductance and capacitance between the windings – that cause additional loss due to unwanted currents. Higher switching loss and the increased influence of printed circuit boards, interconnections and packaging on circuit behavior is another limiting factor. Resonant power conversion can address these problems by using soft switching techniques to reduce switching loss incorporating the parasitics into the circuit elements. However the performance gains are significantly reduced due to the circulating currents when the converter operates out of the nominal operating conditions. As the input voltage or the load change the circulating currents become higher comparing to those ones at nominal operating conditions. Multiple Input-Output Many potential gains from operating resonant converters at higher switching frequency can be obtained if they are employed in applications with favorable input voltage conditions such as those found in distributed power architectures. Load and particularly input voltage regulation reduce a converter’s power density and efficiency. Due to a relatively constant bus voltage in distributed power architectures the resonant converters are suitable for bus voltage conversion (dc/dc or solid state transformation). Unregulated two port dc/dc transformer products achieving very high power density and efficiency figures are based on series resonant converter operating just at the resonant frequency and operating in the megahertz range are already available in the market. However, further efficiency improvements of power architectures are expected to come from using two or more separate low voltage distribution buses instead of a single one. The principal objective of this dissertation is to implement the concept of the series resonant converter operating at its optimum point into a novel bidirectional multiple port dc/dc transformer to address the future needs of power architectures. The new multiple port dc/dc transformer is based on a series resonant converter topology and reduces to only one the number of magnetic components. Soft switching commutations make possible high switching frequencies to be adopted and high power densities to be achieved. Possible problems regarding stray inductances are eliminated since they are absorbed into the circuit elements. The converter features very good inherent load and cross regulation due to the small output impedances. The proposed multiple port dc/dc transformer operates at fixed switching frequency without line regulation. Extensive theoretical analysis of the topology and modeling in details are provided in order to compare with the experimental results. The relationships that show how the output voltage regulation and conduction losses are affected by the circuit parasitics are derived. The methods to select the resonant capacitor values to achieve different design goals such as minimum conduction losses, elimination of cross regulation or ZCS operation at full load of all the secondary side bridges are discussed. ZVS turn-on of all the switches is achieved by relying on the finite magnetizing inductance of the Abstract transformer. A change of the driving pattern is proposed to achieve ZCS operation of all the secondary side bridges independent on load variations or resonant capacitor tolerances. The feasibility of the proposed topology is verified through extensive simulation and experimental work. The optimization of the high frequency transformer design is also addressed in this work since it is the most bulky component in the converter. The impact of dead time interval and the gap size on the overall converter efficiency is analyzed on the design example of the three port dc/dc transformer of several hundreds of watts of the output power for high voltage applications. The final part of this research considers the implementation and performance analysis of the four port dc/dc transformer in a low voltage application of tens of watts of the output power and without isolation requirements.

Non-periodic driving of coupled oscillators:a spherical swing

Nonlinearly coupled, damped oscillators at 1:1 frequency ratio, one oscillator being driven coherently for efficient excitation, are exemplified by a spherical swing with some phase-mismatch between drive and response. For certain damping range, excitation is found to succeed if it lags behind, but to produce a chaotic attractor if it leads the response. Although a period-doubhng sequence, for damping increasing, leads to the attractor, this is actually born as a hard (as regards amplitude) bifurcation at a zero growth-rate parametric line; as damping decreases, an unstable fixed point crosses an invariant plane to enter as saddle-focus a phase-space domain of physical solutions. A second hard bifurcation occurs at the zero mismatch line, the saddle-focus leaving that domain. Times on the attractor diverge when approaching either fine, leading to exactly one-dimensional and noninvertible limit maps, which are analytically determined.

SolarPaces 2013: Innovations on direct steam generation in linear fresnel collectors

Direct Steam Generation (DSG) in Linear Fresnel (LF) solar collectors is being consolidated as a feasible technology for Concentrating Solar Power (CSP) plants. The competitiveness of this technology relies on the following main features: water as heat transfer fluid (HTF) in Solar Field (SF), obtaining high superheated steam temperatures and pressures at turbine inlet (500ºC and 90 bar), no heat tracing required to avoid HTF freezing, no HTF degradation, no environmental impacts, any heat exchanger between SF and Balance Of Plant (BOP), and low cost installation and maintenance. Regarding to LF solar collectors, were recently developed as an alternative to Parabolic Trough Collector (PTC) technology. The main advantages of LF are: the reduced collector manufacturing cost and maintenance, linear mirrors shapes versus parabolic mirror, fixed receiver pipes (no ball joints reducing leaking for high pressures), lower susceptibility to wind damages, and light supporting structures allowing reduced driving devices. Companies as Novatec, Areva, Solar Euromed, etc., are investing in LF DSG technology and constructing different pilot plants to demonstrate the benefits and feasibility of this solution for defined locations and conditions (Puerto Errado 1 and 2 in Murcia Spain, Lidellin Newcastle Australia, Kogran Creek in South West Queensland Australia, Kimberlina in Bakersfield California USA, Llo Solar in Pyrénées France,Dhursar in India,etc). There are several critical decisions that must be taken in order to obtain a compromise and optimization between plant performance, cost, and durability. Some of these decisions go through the SF design: proper thermodynamic operational parameters, receiver material selection for high pressures, phase separators and recirculation pumps number and location, pipes distribution to reduce the amount of tubes (reducing possible leaks points and transient time, etc.), etc. Attending to these aspects, the correct design parameters selection and its correct assessment are the main target for designing DSG LF power plants. For this purpose in the recent few years some commercial software tools were developed to simulatesolar thermal power plants, the most focused on LF DSG design are Thermoflex and System Advisor Model (SAM). Once the simulation tool is selected,it is made the study of the proposed SFconfiguration that constitutes the main innovation of this work, and also a comparison with one of the most typical state-of-the-art configuration. The transient analysis must be simulated with high detail level, mainly in the BOP during start up, shut down, stand by, and partial loads are crucial, to obtain the annual plant performance. An innovative SF configurationwas proposed and analyzed to improve plant performance. Finally it was demonstrated thermal inertia and BOP regulation mode are critical points in low sun irradiation day plant behavior, impacting in annual performance depending on power plant location.

On the formation of nitrogen oxides in the combustion processes of hydrogen in air

A research programme is being carried out at the Institute Nacional de Tecnica Aeroespacial of Spain, on several aspects of the formation of nitrogen oxides in continuous flow combustion systems, considering hydrogen and hydrocarbons as fuels. The research programme is fundamentally oriented on the basic aspects of the problem, although it also includes the study of the influence on the formation process of several operational and design variables of the combusters, such as type of fuels, fuel/air ratio, degree of mixing in premixed type flames, existence of droplets as compared with homogeneous combustion.This problem of nitrogen oxides formation is receiving lately great attention, specially in connection with automobile reciprocating engines and aircraft gas turbines. This is due to the fact of the increasing frequency and intensity of photochemical hazes or smog, typical of urban areas submitted to strong solar radiation, which are originated by the action on organic compounds of the oxidants resulting from the photochemical decomposition of nitrogen dioxide N02. In the combustion process almost all nitrogen oxides are in form of NO. This nitric oxide reacts with the oxygen of the air and forms N02, this reaction only taking place in or near the exhaust of tne motors, since the N0-02 reaction becomes frozen for the concentration existing in the atmosphere.

Efficient hybrid monocular-stereo approach to on-board, video-based traffic sign detection and tracking

In this paper we propose an innovative method for the automatic detection and tracking of road traffic signs using an onboard stereo camera. It involves a combination of monocular and stereo analysis strategies to increase the reliability of the detections such that it can boost the performance of any traffic sign recognition scheme. Firstly, an adaptive color and appearance based detection is applied at single camera level to generate a set of traffic sign hypotheses. In turn, stereo information allows for sparse 3D reconstruction of potential traffic signs through a SURF-based matching strategy. Namely, the plane that best fits the cloud of 3D points traced back from feature matches is estimated using a RANSAC based approach to improve robustness to outliers. Temporal consistency of the 3D information is ensured through a Kalman-based tracking stage. This also allows for the generation of a predicted 3D traffic sign model, which is in turn used to enhance the previously mentioned color-based detector through a feedback loop, thus improving detection accuracy. The proposed solution has been tested with real sequences under several illumination conditions and in both urban areas and highways, achieving very high detection rates in challenging environments, including rapid motion and significant perspective distortion

Using floating car data to analyse the effects of ITS measures and eco-driving

The road transportation sector is responsible for around 25% of total man-made CO2 emissions worldwide. Considerable efforts are therefore underway to reduce these emissions using several approaches, including improved vehicle technologies, traffic management and changing driving behaviour. Detailed traffic and emissions models are used extensively to assess the potential effects of these measures. However, if the input and calibration data are not sufficiently detailed there is an inherent risk that the results may be inaccurate. This article presents the use of Floating Car Data to derive useful speed and acceleration values in the process of traffic model calibration as a means of ensuring more accurate results when simulating the effects of particular measures. The data acquired includes instantaneous GPS coordinates to track and select the itineraries, and speed and engine performance extracted directly from the on-board diagnostics system. Once the data is processed, the variations in several calibration parameters can be analyzed by comparing the base case model with the measure application scenarios. Depending on the measure, the results show changes of up to 6.4% in maximum speed values, and reductions of nearly 15% in acceleration and braking levels, especially when eco-driving is applied.

Factors driving the carbon mineralization priming effect in a sandy loam soil amended with different types of biochar

The effect of biochar on the soil carbon mineral- ization priming effect depends on the characteristics of the raw materials, production method and pyrolysis conditions. The goal of the present study is to evaluate the impact of three different types of biochar on physicochemical properties and CO2 emissions of a sandy loam soil. For this purpose, soil was amended with three different biochars (BI, BII and BIII) at a rate of 8 wt % and soil CO2 emissions were measured for 45 days. BI is produced from a mixed wood sieving from wood chip production, BII from a mixture of paper sludge and wheat husks and BIII from sewage sludge. Cumulative CO2 emissions of biochars, soil and amended soil were well fit to a simple first-order kinetic model with correlation coef- ficients (r 2 ) greater than 0.97. Results show a negative prim- ing effect in the soil after addition of BI and a positive prim- ing effect in the case of soil amended with BII and BIII. These results can be related to different biochar properties such as carbon content, carbon aromaticity, volatile matter, fixed carbon, easily oxidized organic carbon or metal and phenolic substance content in addition to surface biochar properties. Three biochars increased the values of soil field capacity and wilting point, while effects over pH and cation exchange capacity were not observed.

Considering cycling for commuting : the role of mode familiarity : an exploration on the (circular) relation between cycling behaviours and attitudes toward cycling in Vitoria-Gasteiz, Spain

¿La gente utiliza la bicicleta porque les gusta? ¿O es el propio hecho de usarla la razón por la que les gusta hacerlo? ¿O es una combinación de las dos? Este tipo de preguntas reflejan un problema que se puede llamar ‘el círculo de la consideración de la bicicleta’: para poder considerar el uso de la bicicleta en el conjunto de posibles opciones a escoger, un individuo tiene que tener creencias positivas sobre ella, sobre todo en el caso de ‘contextos de bajo uso’. Pero parece poco probable que se formen creencias positivas cuando hay bajos niveles de familiaridad al modo, es decir, con un bajo conocimiento de sus características, su funcionamiento y del imaginario asociado; al mismo tiempo, la familiaridad irá alcanzando niveles más altos conforme aumente el tiempo y la intensidad con la que se utilice la bicicleta a lo largo de la vida de los individuos. El problema parece un circulo recursivo huevo-gallina, ya que es difícil que alguien considere el usar la bicicleta en lugares donde su uso es una práctica poco extendida. En estos lugares, y dentro del conglomerado actual de tecnologías, infraestructuras, reglas, prácticas de los usuarios y preferencias culturales que se han desarrollado alrededor del automóvil (el actual "sistema socio-técnico de la movilidad urbana", Urry 2004; Geels 2005, 2012) usar la bicicleta es considerado por la mayoría como algo difícil, inseguro, y anormal. Como consecuencia, los procesos de aumento de familiaridad con la bicicleta permanecen inactivos. La tesis asume la familiaridad como una fuente de información e influencia sobre las creencias positivas sobre la bicicleta. En ‘contextos de bajo uso’, sin familiaridad al uso de la bicicleta, estas creencias sólo pueden surgir de ciertos rasgos personales (afecto, valores, identidades, voluntad, etc.). Tal como han evidenciado investigaciones recientes, en estos contextos la posibilidad de considerar el uso de la bicicleta (y su eventual adopción), se circunscribe principalmente a los ‘entusiastas’, a los que están dispuestos a “ir contra corriente” (Horton & Parkin 2012), limitando el alcance de las políticas de promoción. La investigación llevada a cabo en esta tesis ofrece un nuevo enfoque al problema del ‘círculo de la consideración de la bicicleta’. Para ello, plantea un modelo en el que se introduce a la familiaridad como un constructo que media entre el comportamiento final –qué modo de transporte elige el individuo– y el conjunto de constructos psicosociales que preceden la elección modal (creencias y actitudes). La familiaridad al uso de la bicicleta se concibe como una medida de la intensidad relativa del uso de una bicicleta, real y percibida (basándose en Diana & Mokhtarian 2009) que puede formarse de manera distinta según sus fines (utilitarios o no utilitarios). El constructo familiaridad con el modo bicicleta está relacionado con la cantidad de tiempo, la intensidad y la regularidad con la que un individuo ha hecho uso de la bicicleta a lo largo de su vida. La familiaridad se concibe así como una condición que permite definir adecuadamente el contexto en el que se toman las decisiones modales de los individuos, en línea con investigaciones que postulan patrones de causalidad alternativos entre los procesos cognitivos de elección y los comportamientos modales (Tardif 1977; Dobson et al. 1978; Golob et al. 1979; Golob 2001; Schwanen et al. 2012; Diana et al. 2009; Vij & Walker 2014). De este modo se plantea que el esquema unidireccional actitudesconductas podría no ser completamente valido en el caso de la consideración de la bicicleta, explorando la hipótesis que sean las propias conductas a influenciar la formación de las actitudes. En esta tesis, el constructo de familiaridad se articula teórica y metodológicamente, y se emplea un instrumento de diseño transversal para contrastarlo. Los resultados de una encuesta telefónica a una muestra representativa de 736 personas en la ciudad española de Vitoria-Gasteiz proveen evidencias que sugieren –aunque de forma preliminar– que la familiaridad juega un papel de mediadora en la relación entre la utilización de la bicicleta y la formación de las creencias y actitudes hacia el su uso. La tesis emplea mediciones para cada individuo con respecto tanto a su consideración como a su familiaridad al uso de la bicicleta. Éstas mediciones se definen haciendo uso del análisis factorial exploratorio (AFE). Por un lado, el AFE arroja una estructura del constructo ‘consideración’ formada por cuatro factores, tres de ellos asociados con elementos positivos y uno con elementos negativos: (1) de cómo el uso de la bicicleta se considera verde e inteligente (G&S); (2) sobre su carácter agradable y adecuado (P&S); (3) sobre su eficacia como modo de transporte para ir al trabajo (E); y (4) sobre los principales inconvenientes de su uso, es decir, las dificultades implícitas (sudoración y estar expuestos a las inclemencias del tiempo) y la sensación de inseguridad que genera (sentirse en riesgo de accidentes y estresarse por el tráfico) (D&T). Por otro lado, la familiaridad al uso de la bicicleta se mide en dos distintas variables ordinales (según se base en el uso utilitario o no utilitario). Como resultado, se puede hablar de que cada individuo se encuentra en una de las siguientes cuatro etapas en orden creciente hacia una familiaridad completa al modo: no familiarizados; apenas familiarizados; moderadamente familiarizados; totalmente familiarizados. El análisis de los datos de los cuatro grupos de sujetos de la muestra, –definidos de acuerdo con cada una de las cuatro etapas de familiaridad definidas– ha evidenciado la existencia de diferencias intergrupo estadísticamente significativas, especialmente para la medida relacionada con el uso utilitario. Asimismo, las personas en los niveles inferiores de familiaridad tienen una consideración menor de los aspectos positivos de la bicicleta y por el contrario presentan preocupaciones mayores hacia las características negativas respecto a aquellas personas que están más familiarizados en el uso utilitario. El uso, aunque esporádico, de una bicicleta para fines utilitarios (ir de compras, hacer recados, etc.), a diferencia de no usarla en absoluto, aparece asociado a unas puntuaciones significativamente más altas en los tres factores positivos (G&S, E, P&S), mientras que parece estar asociado a puntuaciones significativamente más bajas en el factor relacionado con las características negativas (D&U). Aparecen resultados similares cuando se compara un uso moderado, con uno esporádico, sobre todo con respecto a la consideración de las características negativas. Los resultados de esta tesis están en línea con la literatura anterior que se ha basado en variables similares (por ejemplo, de Geus et al. 2008; Stinson & Bhat 2003, 2004; Hunt & Abraham 2006; y van Bekkum et al. 2011a, entre otros), pero en este estudio las diferencias se observan en un contexto de bajo uso y se derivan de un análisis de toda la población de personas que se desplazan a su lugar de trabajo o estudio, lo cual eleva la fiabilidad de los resultados. La posibilidad de que unos niveles más altos de uso de la bicicleta para fines utilitarios puedan llevar a niveles más positivos de su consideración abre el camino a implicaciones teóricas y de políticas que se discuten en la tesis. Con estos resultados se argumenta que el enfoque convencional basado en el cambio de actitudes puede no ser el único y prioritario para lograr cambios a la hora de fomentar el uso de la bicicleta. Los resultados apuntan al potencial de otros esquemas de causalidad, basados en patrones de influencia más descentrados y distribuidos, y que adopten una mirada más positiva hacia los hábitos de transporte, conceptualizándolos como “inteligencia encarnada y pre-reflexiva” (Schwanen et al. 2012). Tales esquemas conducen a un enfoque más práctico para la promoción del uso de la bicicleta, con estrategias que podrían basarse en acciones de ‘degustación’ de su uso o de mayor ‘exposición’ a su uso. Is the fact that people like cycling the reason for them to cycle? Or is the fact that they do cycle the reason for them to like cycling? Or is a combination of the two? This kind of questions reflect a problem that can be called ‘the cycle of cycling consideration’: in order to consider cycling in the set of possible options to be chosen, an individual needs to have positive beliefs about it, especially in the case of ‘low-cycling contexts’. However, positive beliefs seem unlikely to be formed with low levels of mode familiarity, say, with a low acquaintance with mode features, functioning and images; at the same time, higher levels of familiarity are likely to be reached if cycling is practised over relative threshold levels of intensities and extensively across individual life courses. The problem looks like a chicken-egg recursive cycle, since the latter condition is hardly met in places where cycling is little practised. In fact, inside the current conglomerate of technologies, infrastructures, regulations, user practices, cultural preferences that have grown around the automobile (the current “socio-technical system of urban mobility”, Urry 2004; Geels 2005, 2012) cycling is commonly considered as difficult, unsafe, and abnormal. Consequently, the processes of familiarity forming remain disabled, and, as a result, beliefs cannot rely on mode familiarity as a source of information and influence. Without cycling familiarity, origins of positive beliefs are supposed to rely only on personal traits (affect, values, identities, willingness, etc.), which, in low-cycling contexts, confine the possibility of cycling consideration (and eventual adoption) mainly to ‘cycling enthusiasts’ who are willing to “go against the grain” (Horton & Parkin 2012), as it results from previous research. New research conducted by author provides theoretical insights for a different approach of the cycling consideration problem in which the presence of the new construct of cycling familiarity is hypothesised in the relationship between mode choice behaviour and the set of psychosocial constructs that are supposed to precede it (beliefs and attitudes). Cycling familiarity is conceived as a measure of the real and the perceived relative intensity of use of a bicycle (building upon Diana & Mokhtarian 2009) which may be differently formed for utilitarian or non-utilitarian purposes. The construct is assumed to be related to the amount of time, the intensity and the regularity an individual spends in using a bicycle for the two distinct categories of purposes, gaining in this way a certain level of acquaintance with the mode. Familiarity with a mode of transport is conceived as an enabling condition to properly define the decision-making context in which individual travel mode choices are taken, in line with rather disperse research efforts postulating inverse relationships between mode behaviours and mode choices (Tardiff 1977; Dobson et al. 1978; Golob et al. 1979; Golob 2001; Schwanen et al. 2012; Diana et al. 2009; Vij & Walker 2014). The new construct is built theoretically and methodologically, and a cross-sectional design instrument is employed. Results from a telephone survey in a representative sample of 736 commuters in the Spanish city of Vitoria-Gasteiz, provide suggestive –although preliminary– evidence on the role of mode familiarity as a mediator in the relationship between cycling use and the formation of beliefs and attitudes toward cycling. Measures of both cycling consideration and cycling familiarity are defined making use of exploratory factor analysis. On the one hand, four distinct cycling consideration measures are created, based on attitude expressions on four underlying factors relating to the cycling commuting behaviour: on how cycling commuting is considered green and smart (G&S); on its pleasant and suited character (P&S); on its efficiency as a mode of transport for commuting (E); and on the main drawbacks of its use, namely the difficulties implied (sweating and being exposed to adverse weather conditions) and the sense of unsafety it generates (feeling at risk of accidents and getting stressed by traffic) (D&U). On the other hand, dimensions of cycling familiarity are measured on two distinct ordinal variables (whether based on the utilitarian or non-utilitarian use) comprising four stages to a complete mode familiarity: not familiar; barely familiar; moderately familiar; fully familiar. For each of the four stages of cycling familiarity defined, statistical significant differences are found, especially for the measure related to the utilitarian use. Consistently, people at the lower levels of cycling familiarity have a lower consideration of the positive aspects of cycling and conversely they exhibit higher concerns towards the negative characteristics than those individuals that are more familiar in utilitarian cycling. Using a bicycle occasionally for practical purposes, as opposed to not using it at all, seems associated to significant higher scores in the three positive factors (G&S, E, P&S) while it appears to be associated to significant lower scores in the factor relating with the negative characteristics of cycling commuting (D&U). A same pattern also occurs with a moderate use, as opposed to an occasional one, especially for the consideration of the negative characteristics. The results are in line with previous literature based on similar variables (e.g. de Geus et al. 2008; Stinson & Bhat 2003, 2004; Hunt & Abraham 2006; and van Bekkum et al. 2011a, among others), but in this study the differences are observed in a low-cycling context and derive from an analysis of the entire population of commuters, which rises the reliability of results.