Mass transfer properties (permeability and mass diffusivity) of four Australian hardwood species

Characterisation of mass transfer properties was achieved in the longitudinal, radial, and tangential directions for four Australian hardwood species: spotted gum, blackbutt, jarrah and messmate. Measurement of mass transfer properties for these species was necessary to complement current vacuum drying modelling research. Water-vapour diffusivity was determined in steady state using a specific vapometer. Permeability values of some species and material directions were extremely low and undetectable by the mass flow meter device. Hence, a custom system based on volume evolution was conceived to determine very low, previously unpublished, wood permeability values. Mass diffusivity and permeability were lowest for spotted gum and highest for messmate. Except for messmate, in the radial direction, the four species measured were less permeable in all directions than the lowest published figures, demonstrating the high impermeability of Australian hardwoods and partly accounting for their relatively slow drying rates. Premeability, water-vapour diffusivity, and associated anisotropic ratio data obtained for messmate were extreme or did not follow typical trends and is consequently the most difficult of the four woods to dry in terms of collapse and checkinng degradation.

A case of true hermaphroditism reveals an unusual mechanism of twinning

Traditionally twins are classified as dizygous or fraternal and monozygous or identical (Hall Twinning, 362, 2003 and 735-743). We report a rare case of 46,XX/46,XY twins: Twin A presented with ambiguous genitalia and Twin B was a phenotypically normal male. These twins demonstrate a third, previously unreported mechanism for twinning. The twins underwent initial investigation with 17-hydroxyprogesterone and testosterone levels, pelvic ultrasound and diagnostic laparoscopy. Cytogenetic analysis was performed on peripheral blood cells and skin fibroblasts. Histological examination and Fluorescence in situ hybridization studies on touch imprints were performed on gonadal biopsies. DNA analysis using more than 6,000 DNA markers was performed on skin fibroblast samples from the twins and on peripheral blood samples from both parents. Twin A was determined to be a true hermaphrodite and Twin B an apparently normal male. Both twins had a 46,XX/46,XY chromosome complement in peripheral lymphocytes, skin fibroblasts, and gonadal biopsies. The proportion of XX to XY cells varied between the twins and the tissues evaluated. Most significantly the twins shared 100% of maternal alleles and approximately 50% of paternal alleles in DNA analysis of skin fibroblasts. The twins are chimeric and share a single genetic contribution from their mother but have two genetic contributions from their father thus supporting the existence of a third, previously unreported type of twinning.

Water-wave scattering by two submerged plane vertical barriers-Abel integral-equation approach

The classical problem of surface water-wave scattering by two identical thin vertical barriers submerged in deep water and extending infinitely downwards from the same depth below the mean free surface, is reinvestigated here by an approach leading to the problem of solving a system of Abel integral equations. The reflection and transmission coefficients are obtained in terms of computable integrals. Known results for a single barrier are recovered as a limiting case as the separation distance between the two barriers tends to zero. The coefficients are depicted graphically in a number of figures which are identical with the corresponding figures given by Jarvis (J Inst Math Appl 7:207-215, 1971) who employed a completely different approach involving a Schwarz-Christoffel transformation of complex-variable theory to solve the problem.

Opetiopalpus scutellaris Panzer (Coleoptera: Cleridae: Korynetinae) established in the Western Australian wheatbelt

The status of the exotic clerid beetle Opetiopalpus scutellaris Panzer has been unclear due to the ambiguous nature of the single previous Australian record. Recent pheromone trapping at grain stores in Western Australia indicate that O. scutellaris is locally naturalised within the Western Australian wheatbelt. It is considered likely that the trapped O. scutellaris specimens originated from surrounding areas rather than being directly associated with grain.

The white-rot fungi Phlebia radiata and Dichomitus squalens in wood-based cultures: expression of laccases, lignin peroxidases, and oxalate decarboxylase

Basidiomycetous white-rot fungi are the only organisms that can efficiently decompose all the components of wood. Moreover, white-rot fungi possess the ability to mineralize recalcitrant lignin polymer with their extracellular, oxidative lignin-modifying enzymes (LMEs), i.e. laccase, lignin peroxidase (LiP), manganese peroxidase (MnP), and versatile peroxidase (VP). Within one white-rot fungal species LMEs are typically present as several isozymes encoded by multiple genes. This study focused on two effi cient lignin-degrading white-rot fungal species, Phlebia radiata and Dichomitus squalens. Molecular level knowledge of the LMEs of the Finnish isolate P. radiata FBCC43 (79, ATCC 64658) was complemented with cloning and characterization of a new laccase (Pr-lac2), two new LiP-encoding genes (Pr-lip1, Pr-lip4), and Pr-lip3 gene that has been previously described only at cDNAlevel. Also, two laccase-encoding genes (Ds-lac3, Ds-lac4) of D. squalens were cloned and characterized for the first time. Phylogenetic analysis revealed close evolutionary relationships between the P. radiata LiP isozymes. Distinct protein phylogeny for both P. radiata and D. squalens laccases suggested different physiological functions for the corresponding enzymes. Supplementation of P. radiata liquid culture medium with excess Cu2+ notably increased laccase activity and good fungal growth was achieved in complex medium rich with organic nitrogen. Wood is the natural substrate of lignin-degrading white-rot fungi, supporting production of enzymes and metabolites needed for fungal growth and the breakdown of lignocellulose. In this work, emphasis was on solid-state wood or wood-containing cultures that mimic the natural growth conditions of white-rot fungi. Transcript analyses showed that wood promoted expression of all the presently known LME-encoding genes of P. radiata and laccase-encoding genes of D. squalens. Expression of the studied individual LME-encoding genes of P. radiata and D. squalens was unequal in transcript quantities and apparently time-dependent, thus suggesting the importance of several distinct LMEs within one fungal species. In addition to LMEs, white-rot fungi secrete other compounds that are important in decomposition of wood and lignin. One of these compounds is oxalic acid, which is a common metabolite of wood-rotting fungi. Fungi produce also oxalic-acid degrading enzymes of which the most widespread is oxalate decarboxylase (ODC). However, the role of ODC in fungi is still ambiguous with propositions from regulation of intra and extracellular oxalic acid levels to a function in primary growth and concomitant production of ATP. In this study, intracellular ODC activity was detected in four white-rot fungal species, and D. squalens showed the highest ODC activity upon exposure to oxalic acid. Oxalic acid was the most common organic acid secreted by the ODC-positive white-rot fungi and the only organic acid detected in wood cultures. The ODC-encoding gene Ds-odc was cloned from two strains of D. squalens showing the first characterization of an odc-gene from a white-rot polypore species. Biochemical properties of the D. squalens ODC resembled those described for other basidiomycete ODCs. However, the translated amino acid sequence of Ds-odc has a novel N-terminal primary structure with a repetitive Ala-Ser-rich region of ca 60 amino acid residues in length. Expression of the Ds-odc transcripts suggested a constitutive metabolic role for the corresponding ODC enzyme. According to the results, it is proposed that ODC may have an essential implication for the growth and basic metabolism of wood-decaying fungi.

Structure of shock waves at re-entry speeds

The unified structure of steady, one-dimensional shock waves in argon, in the absence of an external electric or magnetic field, is investigated. The analysis is based on a two-temperature, three-fluid continuum approach, using the Navier—Stokes equations as a model and including non-equilibrium collisional as well as radiative ionization phenomena. Quasi charge neutrality and zero velocity slip are assumed. The integral nature of the radiative terms is reduced to analytical forms through suitable spectral and directional approximations. The analysis is based on the method of matched asymptotic expansions. With respect to a suitably chosen small parameter, which is the ratio of atom-atom elastic collisional mean free-path to photon mean free-path, the following shock morphology emerges: within the radiation and electron thermal conduction dominated outer layer occurs an optically transparent discontinuity which consists of a chemically frozen heavy particle (atoms and ions) shock and a collisional ionization relaxation layer. Solutions are obtained for the first order with respect to the small parameter of the problem for two cases: (i) including electron thermal conduction and (ii) neglecting it in the analysis of the outer layer. It has been found that the influence of electron thermal conduction on the shock structure is substantial. Results for various free-stream conditions are presented in the form of tables and figures.

Entsymaattisen hydrolyysin vaikutuksista mikrokiteisen selluloosan rakenteeseen

Cellulose can be used as a renewable raw material for energy production. The utilization requires degradation of cellulose into glucose, which can be done with the aid of enzymatic hydrolysis. In this thesis, various x-ray methods were used to characterize sub-micrometer changes in microcrystalline cellulose during enzymatic hydrolysis to clarify the process and factors slowering it. The methods included wide-angle x-ray scattering (WAXS), small-angle x-ray scattering (SAXS) and x-ray microtomography. In addition, the samples were studied with transmission electron microscopy (TEM). The studied samples were hydrolyzed by enzymes of the Trichoderma reesei species for 6, 24, and 75 hours, which corresponded to 31 %, 58 %, and 68 % degrees of hydrolysis, respectively. Freeze-dried hydrolysis residues were measured with WAXS, SAXS and microtomography, whereas some of them were re-wetted for the wet SAXS and TEM measurements. The microtomography measurements showed a clear decrease in particle size in scale of tens of micrometers. In all the TEM pictures similar cylindrical and partly ramified structures were observed, independent of the hydrolysis time. The SAXS results were ambiguous and partly imprecise, but showed a change in the structure of wet samples in scale of 10-30 nm. According to the WAXS results, the degrees of crystallinity and the crystal sizes remained the same. The gained results support the assuption, that the cellulosic particles are hydrolyzed mostly on their surface, since the enzymes are unable to penetrate into the nanopores of wet cellulose. The hydrolysis therefore proceeds quickly in easily accessible particles and leaves the unaccesible particles almost untouched. The structural changes observed in the SAXS measurements might correspond to slight loosening of the microfibril aggregates, which was seen only in the wet samples because of their different pore structure.

Adsopption isotherms-A critique

The possibility or the impossibility of separating the particle and the electrode interactions is discussed in a wider context of the effects due to any two interaction potentials on the equation of state. The involved nature of the pressure dependence on two individually definable forces is illustrated through the Percus Yevick results for the adhesive hard spheres. An alternative form of the adsorption isotherm is given to bring home the intimate relationship between the actual equation of state and the free energy of adsorption. Thermodynamic consequences of congruence with respect to E (or q) as reflected through the linear plots of q (or E) vs. θ are well known. Mathematical consequences of simultaneous congruence have been pointed out recently. In this paper, the physical nature of congruence hypothesis is revealed. In passing "the pseudo-congruence" is also discussed. It is emphasised that the problem is no less ambiguous with regard to modelling the particle/particle interaction. The ad hoc nature of our dependence of the available equations of state is emphasised through a discussion on the HFL theory. Finally, a heuristic method for modelling ΔG mathematically-incorporating its behaviour at saturation coverages-is advanced. The more interesting aspects of this approach, which generalises almost all isotherms hitherto known, are sketched.

Ernest W. Michel Papers, 1698, 1938-1996 (bulk 1946-1987)

This collection contains the papers of Ernest W. Michel, Holocaust Survivor Journalist and public speaker,including clippings of newspaper articles written by and about Michel, correspondence between Michel and many important Jewish and political figures and autograph files, which Michel collected. Many of these files concern Michel’s Holocaust experiences, speaking engagements, the World Gathering of Jewish Holocaust Survivors, and Michel’s work with the United Jewish Appeal.

Designing self-service technologies for e-wellness

In the context of an international economic shift from manufacturing to services and the constant expansion of industries towards online services (Sheth and Sharma, 2008), this study is concerned with the design of self-service technologies (SSTs) for online environments. An industry heavily adopting SSTs across a variety of different services is Health and Wellness, where figures show an ever growing number of health and wellness apps being developed, downloaded and abandoned (Kelley, 2014). Little is known about how to enhance people’s engagement with online wellness SSTs to support self-health management and self-efficacy. This literature review argues that service design of wellness SSTs in online contexts can be improved by developing an enhanced understanding from a people perspective and customer experience point of view. Customer value, quality of service, usability, and self-efficacy all play an important role in understanding how to design SSTs for wellness and keep users engaged. There is a need for further study on how people interact and engage with online services in the context of wellness in order to design engaging wellness services.

Aussie retailers should get their Christmas wish this year

Consumer Sentiment fell by 4.8% in December, but despite the drop other indicators still point toward a robust Christmas period for retailers. Retail trade recorded its strongest result for three consecutive months to October, with Queensland and Western Australia leading the way. A closer inspection of ABS Retail figures indicate six consecutive months of positive results and this suggests consumer confidence has finally returned to the market. But it may not be a rosy outlook for all retail sectors. Overall we are spending more, but not where we once traditionally did.

Properties of Ammonium Nitrate based fertilisers

The text is divided into three parts; Properties, Application and Safety of Ammonium Nitrate (AN) based fertilisers. In Properties, the structures and phase transitions of ammonium and potassium nitrate are reviewed. The consequences of phase transitions affect the proper use of fertilisers. Therefore the products must be stabilised against the volume changes and consequent loss of bulk density and hardness, formation of dust and finally caking of fertilisers. The effect of different stabilisers is discussed. Magnesium nitrate, ammonium sulphate and potassium nitrate are presented as a good compromise. In the Application part, the solid solutions in the systems (K+,NH4+)NO3- and (NH4+,K+)(Cl-,NO3-) are presented based on studies made with DSC and XRD. As there are clear limits for solute content in the solvent lattice, a number of disproportionation transitions exist in these process phases, e.g., N3 (solid solution isomorphous to NH4NO3-III) disproportionates to phases K3 (solid solution isomorphous to KNO3-III) and K2 (solid solution isomorphous to KNO3-II). In the crystallisation experiments, the formation of K3 depends upon temperature and the ratio K/(K+NH4). The formation of phases K3, N3, and K2 was modelled as a function of temperature and the mole ratios. In introducing chlorides, two distinct maxima for K3 were found. Confirmed with commercial potash samples, the variables affecting the reaction of potassium chloride with AN are the particle size, time, temperature, moisture content and amount of organic coating. The phase diagrams obtained by crystallisation studies were compared with a number of commercial fertilisers and, with regard to phase composition, the temperature and moisture content are critical when the formation and stability of solid solutions are considered. The temperature where the AN-based fertiliser is solidified affects the amount of compounds crystallised at that point. In addition, the temperature where the final moisture is evaporated affects the amount and type of solid solution formed at this temperature. The amount of remaining moisture affects the stability of the K3 phase. The K3 phase is dissolved by the moisture and recrystallised into the quantities of K3, which is stable at the temperature where the sample is kept. The remaining moisture should not be free; it should be bound as water in the final product. The temperatures during storage also affect the quantity of K3 phase. As presented in the figures, K3 phase is not stable at temperatu¬res below 30 °C. If the temperature is about 40 °C, the K3 phase can be formed due to the remaining moisture. In the Safety part, self-sustaining decomposition (SSD), oxidising and energetic properties of fertilisers are discussed. Based on the consequence analysis of SSD, early detection of decomposition in warehouses and proper temperature control in the manufacturing process is important. SSD and oxidising properties were found in compositions where K3 exists. It is assumed that potassium nitrate forms a solid matrix in which AN can decompose. The oxidising properties can be affected by the form of the product. Granular products are inherently less oxidising. Finally energetic properties are reviewed. The composition of the fertiliser has an importance based on theoretical calculations supported by experimental studies. Materials such as carbonates and sulphates act as diluents. An excess of ammonium ions acts as a fuel although this is debatable. Based on the experimental work, the physical properties have a major importance over the composition. A high bulk density is of key importance for detonation resistance.

Medal of the 11th Hapoel Games

Obverse: Emblem of the games, inscription. Reverse: Figures of four athletes engaged in various sports.

Tiberias Commemorative Medal

Obverse: A stylized figures of a fisherman and a girl carrying basket with fruit. In the background, the sea and a house. Reverse: Coin from Tiberias minted in 101 C.E. during the reign of Trajan II. On the coin- Hygiea, goddess of health, who holds a bowl and serpent and its seated upon a rock whence a hot springs gush.

Study of the Prophet Ezekiel.

Signed and titled lower center, with a dedication to the LeoBaeck Institute, dated 1961.