Forced-air, vacuum, and hydro precooling of cauliflower (Brassica oleracea L. var. botrytis cv. Freemont): part I. determination of precooling parameters

The aim of the present study was to precool cauliflower using forced-air, vacuum and high and low flow hydro cooling methods. The weight of the precooled cauliflower heads (5000±5 g) was measured before they were placed in standard plastic crates. Cauliflower heads, whose initial temperature was 23.5 ± 0.5 ºC, were cooled until the temperature reached at 1 ºC. During the precooling process, time-dependent temperature and energy consumption were measured, and during vacuum precooling, the decreasing pressure values were recorded, and a curve of time-dependent pressure decrease (vacuum) was built. The most suitable cooling method to precool cauliflower in terms of cooling time and energy consumption was vacuum, followed by the high and low flow hydro and forced-air precooling methods, respectively. The highest weight loss was observed in the vacuum precooling method, followed by the forced-air method. However, there was an increase in the weight of the cauliflower heads in the high and low flow hydro precooling method. The best colour and hardness values were found in the vacuum precooling method. Among all methods tested, the most suitable method to precool cauliflower in terms of cooling and quality parameters was the vacuum precooling method.

Forced-air, vacuum, and hydro precooling of cauliflower (Brassica oleracea L. var. botrytis cv. Freemont): Part II. Determination of quality parameters during storage

Cauliflower heads, which were precooled using four different methods including vacuum, forced-air, and high and low flow hydro precooling, were stored under controlled atmosphere and room conditions. Controlled atmosphere conditions (CA) were as follows: 1°C temperature, 90 ± 5% relative humidity, and 0:21 [(%CO2:%O2) – (0:21) control] atmosphere composition. Room conditions (RC) were: 22±1°C temperature and 55-60% humidity. Various quality parameters of the cauliflower heads were assessed during storage (days 0, 7, 14, 21, 28, and 35) under controlled atmosphere and room conditions (days 0, 5, and 10). During storage, weight loss, deterioration rate, overall sensory quality score, hardness, and colour (L, a, b, C and α) were evaluated. In the present study, the strength and quality parameters of cauliflower under CA and RC conditions were obtained. Vacuum precooling was found to be most suitable method before cauliflower was submitted to cold storage and sent to market. Furthermore, the storage of cauliflower without precooling resulted in a significant decrease in quality parameters.

Microbiological and sensory evaluation of Jambu (Acmella oleracea L.) dried by cold air circulation

Abstract The aim of this study was to evaluate the microbiological and sensory quality of the Jambu (Acmella oleracea L.) in natura and dried by cold air, and the determination of its drying curve. The microbiological analysis were performed to Salmonella spp, the coagulase-positive Staphylococcus, and coliforms in the both Jambu samples, at 45 °C. Tacacá, the typical food dish of Pará state, Brazil, has showed good consumer global acceptance in the sensory evaluation of Jambu in natura (score of 8.00 ± 1.46) and dried (score of 8.67 ± 0.66). Both samples, Jambu in natura and dried by cold air, were by the current legislation regarding the microbiological aspects, this is the absence of Salmonella spp, coagulase-positive Staphylococcus <1×101 CFU/g, and coliforms <3 MPN/g, at 45 °C. Thus, considering sensory and health aspects, the commercialization of dried Jambu becomes viable, facilitating its transportation and handling, as well as for reducing its vegetable mass.

Underwater Remote Welding Technology for Offshore Structures

The construction of offshore structures, equipment and devices requires a high level of mechanical reliability in terms of strength, toughness and ductility. One major site for mechanical failure, the weld joint region, needs particularly careful examination, and weld joint quality has become a major focus of research in recent times. Underwater welding carried out offshore faces specific challenges affecting the mechanical reliability of constructions completed underwater. The focus of this thesis is on improvement of weld quality of underwater welding using control theory. This research work identifies ways of optimizing the welding process parameters of flux cored arc welding (FCAW) during underwater welding so as to achieve desired weld bead geometry when welding in a water environment. The weld bead geometry has no known linear relationship with the welding process parameters, which makes it difficult to determine a satisfactory weld quality. However, good weld bead geometry is achievable by controlling the welding process parameters. The doctoral dissertation comprises two sections. The first part introduces the topic of the research, discusses the mechanisms of underwater welding and examines the effect of the water environment on the weld quality of wet welding. The second part comprises four research papers examining different aspects of underwater wet welding and its control and optimization. Issues considered include the effects of welding process parameters on weld bead geometry, optimization of FCAW process parameters, and design of a control system for the purpose of achieving a desired bead geometry that can ensure a high level of mechanical reliability in welded joints of offshore structures. Artificial neural network systems and a fuzzy logic controller, which are incorporated in the control system design, and a hybrid of fuzzy and PID controllers are the major control dynamics used. This study contributes to knowledge of possible solutions for achieving similar high weld quality in underwater wet welding as found with welding in air. The study shows that carefully selected steels with very low carbon equivalent and proper control of the welding process parameters are essential in achieving good weld quality. The study provides a platform for further research in underwater welding. It promotes increased awareness of the need to improve the quality of underwater welding for offshore industries and thus minimize the risk of structural defects resulting from poor weld quality.

Characterization of amine-based CO2 adsorbent for Direct Air Capture

Direct air capture technologies extract CO2 from air at a concentration of as low as 400ppm. The captured CO2 can be used for the production of synthetic methane or liquid fuels. In the literature survey of this thesis, results related to direct air capture by using solid sorbents are presented and critically discussed. In the experimental part, a proprietary amine functionalized resin is characterized for direct air capture. Structural comparison is also made to a commercial resin of similar type. Based on the literature survey, the most important parameters in direct air capture process are low adsorption and desorption temperatures, good cyclic stability in dry and humid conditions, high CO2 outlet purity and a high working capacity. Primary amine functionalized solid sorbents are found to often have good qualities for direct air capture, but overall process performance is rarely studied exhaustively. Based on FTIR spectra, both resin adsorbents are found to be consisted of polystyrene functionalized with primary amine, and capture CO2 by forming carbamate. The commercial resin is more porous, has a slightly higher particle size and contains fewer impurities. Important physical parameters are gained of the proprietary resin, such as internal porosity and median particle size. The resin’s amine group is found to endure thermal treatment reasonably well. CO2 adsorption capacity gained by thermal gravimetry from 400ppm CO2 is highest at 25oC, and is found to be reasonable compared to values presented in literature. Thus, the resin is stated to exhibit promising qualities for direct air capture.

Drying soybean seed using air ambient temperature at low relative humidity

Under subtropical and tropical environments soybean seed (Glycine max (L.) Merrill) are harvested early to avoid deterioration from weathering. Careful after-harvest drying is required and is an important step in maintaining the physiological quality of the seed. Soybean seed should be harvested when the moisture content is in a range of 16-20%. Traditional drying utilizes a high temperature air stream passed through the seed mass without dehumidification. The drying time is long because the system is inefficient and the high temperature increases the risk of thermal damage to the seed. New technology identified as heat pipe technology (HPT) is available and has the unique feature of removing the moisture from the air stream before it is passed through the seed mass at the same environmental temperature. Two studies were conducted to evaluate the performance of HPT for dry soybean seed. In the first study the seeds were dried from 17.5 to 11.1% in 2 hours and 29 minutes and in the second sudy the seeds were dried from 22.6 to 11.9% in 16 hours and 32 minutes. This drying process caused no reduction in seed quality as measured by the standard germination, tetrazolium-viability, accelerated aging and seedling vigor classification tests. The only parameter that indicated a slight seed quality reduction was tetrazolium vigor in the second study. It was concluded that the HPT system is a promising technology for drying soybean seed when efficiency and maintenance of physiological quality are desired.

Drying peanut seed using air ambient temperature at low relative humidity

The moisture content of peanut kernel (Arachis hypogaea L.) at digging ranges from 30 to 50% on a wet basis (w.b.). The seed moisture content must be reduced to 10.5% or below before seeds can be graded and marketed. After digging, peanuts are cured on a window sill for two to five days then mechanically separated from the vine. Heated air is used to further dry the peanuts from approximately 18 to 10% moisture content w.b. Drying is required to maintain peanut seed and grain quality. Traditional dryers pass a high temperature and high humidity air stream through the seed mass. The drying time is long because the system is inefficient and the high temperature increases the risk of thermal damage to the kernels. New technology identified as heat pipe technology (HPT) is available and has the unique feature of removing the moisture from the air stream before it is heated and passed through the seed. A study was conducted to evaluate the performance of the HPT system in drying peanut seed. The seeds inside the shells were dried from 17.4 to 7.3% in 14 hours and 11 minutes, with a rate of moisture removal of 0.71% mc per hour. This drying process caused no reduction in seed quality as measured by the standard germination, accelerated ageing and field emergence tests. It was concluded that the HPT system is a promising technology for drying peanut seed when efficiency and maintenance of physiological quality are desired.

Air-Sea Battle -konsepti John Wardenin Enemy as a System -teorian näkökulmasta

Tutkielman tavoitteena oli analysoida Air-Sea Battle -konseptia ja sen lähtökohtana ollutta viholliskuvaa John Wardenin Enemy as a System -teorian näkökulmasta julkisten asiakirjojen, raporttien ja artikkeleiden avulla. Tutkimusmenetelmänä on käytetty teoriaohjaavaa sisällönanalyysia. Tutkimusongelmaksi muodostui: ”Miten Air-Sea Battle -konsepti näyttäytyy Wardenin Enemy as a System -teorian näkökulmasta?” Tutkimuskysymyksien avulla pyrittiin lisäksi löytämään konseptin kehittämiseen johtaneita tekijöitä suurstrategisella tasolla, arvioimaan konseptin mukaista aseellisen voiman käyttöä sekä analysoimaan konseptia suhteessa Wardenin näkemyksiin sotilasstrategiasta. Wardenin Enemy as a System -teoria on esitelty tutkielman alkupuolella hyödyntäen alkuperäistekstejä, aiheesta kirjoitettuja tutkimuksia ja artikkeleita sekä sotataidollista kirjallisuutta. Air-Sea Battle -konseptia käsittelevän luvun aineisto on luokiteltu Wardenin neljän strategisen kysymyksen teemojen, eli tavoitteen, vaikuttamisen kohteiden, keinojen ja irtautumisen, mukaisesti. Tärkeimmät lähteet varsinaisen Air-Sea Battle -asiakirjan lisäksi olivat Yhdysvaltojen turvallisuus- ja sotilasstrategiaa määrittelevät dokumentit, tutkimuslaitosten julkaisemat raportit sekä aikakauslehtiartikkelit. Aineiston perusteella Yhdysvallat näkee tiettyjen valtioiden, kuten Kiinan, kehittyvät niin kutsutut anti-access/area denial -suorituskyvyt uhkana alueelliselle tasapainolle ja heidän kyvylleen ylläpitää sotilaallista läsnäoloa strategisesti merkittävillä alueilla. Air-Sea le -konseptin tavoitteena on määritellä ja kehittää suorituskyvyt, operatiiviset suunnitelmat ja toimintamallit, joiden mukaan toimivalla joukolla kyetään luomaan riittävä pelotevaikutus konfliktin ehkäisemiseksi tai säilyttämään toiminnanvapaus alueella sen muodostuessa.

Air defence in Northern Europe

Finnish Defence Studies is published under the auspices of the National Defence College, and the contributions reflect the fields of research and teaching of the College. Finnish Defence Studies will occasionally feature documentation on Finnish Security Policy. Views expressed are those of the authors and do not necessarily imply endorsement by the National Defence College.

Helsinki hub – new traffic flows and business networks

This thesis is the Logistics Development Forum's assignment and the work dealing with the development of the Port of Helsinki as part of Helsinki hub. The Forum aims to develop logistics efficiency through public-private co-operation and development of the port is clearly dependent on both factors. Freight volumes in the Port of Helsinki are the biggest single factor in hub and, therefore, the role of the port of the entire hub development is strong. The aim is to look at how the port will develop as a result of changes in the foreign trade of Finland and the Northern European logistics trends in 25 years time period. Work includes the current state analysis and scenario work. The analyses are intended to find out, which trends are the most important in the port volume development. The change and effect of trends is examined through scenarios based on current state. Based on the work, the structure of Finnish export industry and international demand are in the key role in the port volume development. There is significant difference between demands of Finnish exporting products in different export markets and the development between the markets has different impacts on the port volumes by mass and cargo type. On the other hand, the Finnish economy is stuck in a prolonged recession and competition between ports has become a significant factor in the individual port's volume development. Ecological valuesand regulations have changed the competitive landscape and maritime transport emissions reductions has become an important competitive factor for short routes in the Baltic Sea, such as in the link between Helsinki and Tallinn.

Natural freeze crystallization : purification of aqueous Na2SO4 solutions with cold air

The aim of this thesis was to examine efficiency of freeze crystallization and eutectic freeze crystallization in purification of wastewater by imitating natural freezing. In addition, a mathematic model based on heat transfer to determine ice thickness and ice growth rate was examined. Also, the amount of sodium sulfate crystallized at the eutectic point was under investigation. In literature part, advantages and applications of the freeze crystallization are discussed, and possibility to apply it in Northern hemisphere winter weather conditions is under study. Furthermore, main sources of sodium sulfate from Finnish industries are described. The experiments were carried out in modified chest freezer, where a fan was placed in order to obtain laminar air flow inside. Picolog PT-104 data logger was used to monitor temperature changes in the salt-water solution, and constant temperature was maintained in the crystallizer with Lauda RP 850 thermostat. The impurity of formed ice layer was determined by weighing ice samples after experiment and again after 24 hours drying to full dryness in oven. Volume of salt-water solution was also measured after experiment. The highest purity of formed ice layer was obtained with small temperature difference and with long freezing time. On the other hand, the amount of crystallized sodium sulfate was its greatest with long freezing time and higher temperature difference. The results obtained by the mathematic model and empirical results did not differ significantly in most of the experiments. However, the difference increased when salt-water mixture reached its eutectic point, leading to simultaneous ice and salt crystallization. Eutectic point was reached only with the highest salt concentration with one exception. In these cases, calculated values were in many cases greater than the experimental ones. In winter weather conditions freeze crystallization is cost-effective wastewater treatment method and rather simple. Nonetheless, the efficiency and separation rate are strongly depended on ambient temperature and its changes