The annealing behavior of Cu nanoparticles in Ar-ion implanted spinel

Magnesium aluminate spinel crystals (MgAl2O4 (1 1 0)) deposited with 30 nm Cu film on surface were implanted with 110 key Ar-ions to a fluence of 1.0 x 10(17) ions/cm(2) at 350 degrees C, and then annealed in vacuum condition at the temperature of 500, 600, 700, 800 and 900 degrees C for 1 h, respectively. Ultraviolet-visible spectrometry (UV-VIS), scanning electron microscopy (SEM), Rutherford backscattering (RBS) and transmission electron microscopy (TEM) were adopted to analyze the specimens. After implantation, the appearance of surface plasmon resonance (SPR) absorbance peak in the UV-VIS spectrum indicated the formation of Cu nanoparticles, and the TEM results for 500 degrees C also confirmed the formation of Cu nanoparticles at near-surface region. In annealing process, The SPR absorbance intensity increased at 500 and 700 degrees C, decreased with a blue shift of the peak position at 600 and 800 degrees C, and the peak disappeared at 900 degrees C. The SPR absorbance intensity evolution with temperature was discussed combined with other measurement results (RBS, SEM and TEM). (C) 2010 Elsevier B.V. All rights reserved.

30MeV/u~(40)Ar+~(nat)Ag反应中中等质量碎片的发射机制及其发射时间测量

中等质量碎片（IMF）的发射是中能重离子碰撞的一大特点，且随着轰击能量的升高其产额迅速增加。通过测量30MeV/u 40Ar+natAg反应中出射的中等质量碎片，研究了高激发热核的发射机制、发射时标和时空演化规律。 对反应中发射碎片能谱的运动源拟合表明，前角区（11°—22°）中等质量碎片（IMF）来自于三种成分：类靶源、类弹源和中速源成分，其中类弹和中速成分占主导，关联测量的IMF能谱拟合得到，一个来自于类弹源而另一个来自于中速源成分的事件占有相当大的比例。 利用小相对角度内的两碎片关联测量，研究高激发核衰变中中等质量碎片的发射时标和寿命。IMF发射时间随能量的变化很大，从低能碎片的250 fm/c到高能粒子的100 fm/c，表明在此能量下，反应中出射的IMF主要来自于相继两体衰变。通过与其它实验的比较可知，随着束流能量的升高，IMF发射时间由相继两体衰变向多重碎裂过渡。 IMF时空演化研究表明，发射空间的大小对IMF关联函数的影响主要来自于发射源的核物质密度而几乎不依赖于发射源的质量数。

中能区~(40)Ar + ~(197)Au/~(159)Tb/~(nat)Ag反应中高激发热核性质研究

通过对中能区Ar+Au/Tb/Ag反应中高激发核的发射时标、发射次序、发射机制、核温度、集体运动等衰变特性的研究，提取了轻粒子和中等质量碎片（IMF）的发射时间，IMF发射时间随束流能的升高而变短，发射机制逐渐由相继衰变过渡至多重碎裂。研究了轻粒子和碎片间的发射次序，对高能粒子和碎片，轻粒子先于碎片发射，而低能时，则为碎片先于轻粒子发射。IMF发射成分与角度和碰撞参数有关，前角区来自于弹核碎裂，后角区来自于类靶热核的蒸发。在平面和出平面研究表明，中速粒子和碎片为在平面发射占主导，即存在类转动效应；对轻粒子，转动效应随粒子质量增加而增加；对中速产物均观测到该效应随碰撞参数饿增大而增大。采用几种不同的方法提取了热核的核温度，研究了不同方法之间的区别。

Development of functionalized terbium fluorescent nanoparticles for antibody labeling and time-resolved fluoroimmunoassay application

Silica-based functionalized terbium fluorescent nanoparticles were prepared, characterized and developed as a fluorescence probe for antibody labeling and time-resolved fluoroimmunoassay. The nanoparticles were prepared in a water-in-oil (W/O) microemulsion containing a strongly fluorescent Tb3+ chelate. N,N.N-1,N-1-12,6-bis(3'-aminomethyl-1'-pyrazolyl)phenylpyridine] tetrakis(acetate)-Tb3+ (BPTA-Tb3+), Triton X-100, octanol, and cyclohexane by controlling copolymerization of tetraethyl orthosilicate (TEOS) and 3-[2-(2- aminoethylamino)-ethylamino]propyl-trimethoxysilane (AEPS) with ammonia water. The characterizations by transmission electron microscopy and fluorometric quantum methods show that the nanoparticles are spherical and uniform in size, 45 +/- 3 nm in diameter, strongly fluorescent with fluorescence yield of 10% and a long fluorescence lifetime of 2.0 ms. The amino groups directly introduced to the nanoparticle's surface by using AEPS in the preparation made the surface modification and bioconjugation of the nanoparticles easier. The nanoparticle-labeled anti-human alpha-fetoprotein antibody was prepared and used for time-resolved fluoroimmunoassay of (x-fetoprotein (AFP) in human serum samples. The assay response is linear from 0.10 ng ml(-1) to about 100 ng ml(-1) with the detection limit of 0.10 ng ml(-1). The coefficient variations (CVs) of the method are less than 9.0%. and the recoveries are in the range of 84-98% for human serum sample measurements. (C) 2004 Elsevier B.V. All rights reserved.

On the propagation rate of the chemical waves observed during the course of CO oxidation on a Ag/Pt(110) composite surface

We have analyzed the propagation rate of the chemical waves observed during the course of CO oxidation on a Ag/Pt(I 10) composite surface that were reported in our previous papers [Surf Interface Anal. 2001, 32, 179; J. Phys. Chem. B 2002, 106, 5645]. In all cases, the propagation rate v can be adequately fitted as v = v(0) + D-0/d, in which v(0) and D-0 are constants, and d is the distance between the reaction front of the chemical wave and the boundary from which the chemical wave originates. We propose that the surface species responsible for the formation of the chemical wave comes from two paths: the adsorption of molecules in the gas phase on the surface and the migration from the adjacent surface with different catalytic activity. v(0) corresponds to the contribution from the surface species due to the adsorption, and D-0/d to that of the surface species that migrates from the adjacent surface. The rate equation clearly suggests that the observed chemical wave results from the coupling between adjacent surfaces with different catalytic activities during the course of heterogeneous catalysis. These results, together with our previous reports, provide a good fundamental understanding of spillover, an important phenomenon in heterogeneous catalysis.

Epoxidation of propylene over Ag-CuCl catalysts using air as the oxidant

Ag-CuCl catalysts were found to be active and selective for the epoxidation of propylene using air as the oxidant. Ag catalyst gives a propylene conversion of 31.6%, with a propylene oxide (PO) selectivity of 0.42% at a reaction temperature of 350 degreesC after 220 min of reaction. Addition of CuCl significantly improves the selectivity to PO, and suppresses the conversion of propylene. The Ag-CuCl (1/0.6) catalyst gives propylene conversion of about 3% and a PO selectivity of about 30% at a reaction temperature of 350 degreesC after 500 min of reaction. The activity of the Ag-CuCl catalyst increases with the reaction time and the selectivity to PO is very stable for this catalyst. It is found that AgCl and CuO phases formed during the catalyst preparation are beneficial to the epoxidation of propylene.

Preparation and Characterization of BaLiF3:Er3+ Nanoparticles by the Hydrothermal Microemulsion Synthesized Method

Nanoparticles of BaLiF3:Er3+ were prepared from the quaternary microemulsions of Cetyltrim-Enthyl Ammonium Bromide (CTAB), n-butanol, n-octane, and water, using the hydrothermal-microemulsion technique. The complex fluorides were characterized by means of X-ray power diffraction, Environmental Scanning Electron Microscopy (ESEM), and fluorescence spectra.

Fabrication and characterization of CdTe nanoparticles attached to poly(4-vinylpyridine) nanofibers

The major objective of this work was to characterize the status of CdTe nanoparticles attached to the surface of poly(4-vinylpyridine) (P4VP) nanofibers. Scanning electron microscopy and transmission electron microscopy images indicated that the attachment of CdTe nanoparticles enlarged the diameter of P4VP nanofibers. Moreover, the results of the energy-dispersive X-ray spectrum and the electron diffraction pattern revealed that the deposition on the surface of P4VP nanofibers was CdTe in a cubic lattice