空气分级燃烧炉膛壁面温度分布研究

本文在1MW切向燃烧煤粉炉试验台上进行了空气分级燃烧试验，研究了空气分级燃烧时炉膛壁面温度分布规律。试验结果表明，在空气分级燃烧时主燃区壁面温度分布相对于炉壁中心位置呈左右不对称分布，炉壁最高温度大致出现在旋转气流的上游，壁面温度分布不均匀系数为0.244；燃尽区下部壁面温度分布也呈不对称分布，最高温度出现在旋转气流的下游，壁面温度分布不均匀系数为0.106；燃尽区上部壁面壁面温度分布分布均匀。

Reinterpretación de la nasalización en terena, cubeo y chimila desde la Fonología Natural

106 p.

Report of the Inter-American Tropical Tuna Commission for the year 1965

ENGLISH: The Inter-American Tropical Tuna Commission has been assigned the task, under the Convention which created it, of gathering and interpreting factual information to facilitate the maintenance of tunas and tuna-baitfishes of the eastern Pacific Ocean at levels of abundance which will permit maximum sustained catches. SPANISH: Se le ha asignado a la Comisión Interamericana del Atún Tropical bajo la Convención que la formó, la tarea de recoger e interpretar la información científica para facilitar el mantenimiento de los atunes y de los peces de carnada en el Océano Pacífico oriental, a niveles de abundancia que permitan un sostenimiento máximo de capturas. (PDF contains 106 pages.)

The relationship between the radio and gamma-ray emission of blazars

Blazars are active galaxies with a jet closely oriented to our line of sight. They are powerful, variable emitters from radio to gamma-ray wavelengths. Although the general picture of synchrotron emission at low energies and inverse Compton at high energies is well established, important aspects of blazars are not well understood. In particular, the location of the gamma-ray emission region is not clearly established, with some theories favoring a location close to the central engine, while others place it at parsec scales in the radio jet.

We developed a program to locate the gamma-ray emission site in blazars, through the study of correlated variations between their gamma-ray and radio-wave emission. Correlated variations are expected when there is a relation between emission processes at both bands, while delays tell us about the relative location of their energy generation zones. Monitoring at 15 GHz using the Owens Valley Radio Observatory 40 meter telescope started in mid-2007. The program monitors 1593 blazars twice per week, including all blazars detected by the Fermi Gamma-ray Space Telescope (Fermi) north of -20 degrees declination. This program complements the continuous monitoring of gamma-rays by Fermi.

Three year long gamma-ray light curves for bright Fermi blazars are cross-correlated with four years of radio monitoring. The significance of cross-correlation peaks is investigated using simulations that account for the uneven sampling and noise properties of the light curves, which are modeled as red-noise processes with a simple power-law power spectral density. We found that out of 86 sources with high quality data, only three show significant correlations (AO 0235+164, B2 2308+34 and PKS 1502+106). Additionally, we find a significant correlation for Mrk 421 when including the strong gamma-ray/radio flare of late 2012. In all four cases radio variations lag gamma-ray variations, suggesting that the gamma-ray emission originates upstream of the radio emission. For PKS 1502+106 we locate the gamma-ray emission site parsecs away from the central engine, thus disfavoring the model of Blandford and Levinson (1995), while other cases are inconclusive. These findings show that continuous monitoring over long time periods is required to understand the cross-correlation between gamma-ray and radio-wave variability in most blazars.

Die Bestandssituation der wichtigsten Nutzfischarten im NO-Atlantik 1992/93 unter besonderer Berücksichtigung des Kabeljaus

Fischarten im Nordostatlantik, die eine besondere Bedeutung für die deutsche Fischerei haben, sind Kabeljau, Schellfisch; Seelachs und Rotbarsch. Vieles aus der Biologie und über die verbreitung dieser wichtigen Nutzfische ist bekannt. Dennoch geben die großen Bestandsveränderungen sowohl der Fischerei wie auch der Fischereiwissenschaft immer wieder Rätsel um ihre Ursachen auf. Man kann vermuten, dass es ökologische oder klimatische, hydrologische oder fischereiliche Gründe sind, die solche Bestandsfluktuationen herbeiführen. Die Aufgabe der Wissenschaft ist es, die wahre Ursache nachzuweisen.

Die Tintenfisch-Fänge der Deutschen Hochseefischerei in den Jahren 1974 - 1987

Der Konsum von Tintenfischen (Cephalopoden) steigt in der Bundesrepublik Deutschland von Jahr zu Jahr. Während in den sechziger Jahren Tintenfische noch als Exoten auf den Speisekarten geführt wurden, sind sie nunmehr "Standard". Der vorliegende Beitrag soll vermitteln, welchen Stellenwert die Tintenfisch-Anlandungen der Bundesrepublik Deutschland im Vergleich mit den Fängen anderer Nationen im Atlantik haben.

Strength of tantalum at high pressures through Richtmyer-Meshkov laser compression experiments and simulations

Strength at extreme pressures (>1 Mbar or 100 GPa) and high strain rates (106-108 s-1) of materials is not well characterized. The goal of the research outlined in this thesis is to study the strength of tantalum (Ta) at these conditions. The Omega Laser in the Laboratory for Laser Energetics in Rochester, New York is used to create such extreme conditions. Targets are designed with ripples or waves on the surface, and these samples are subjected to high pressures using Omega’s high energy laser beams. In these experiments, the observational parameter is the Richtmyer-Meshkov (RM) instability in the form of ripple growth on single-mode ripples. The experimental platform used for these experiments is the “ride-along” laser compression recovery experiments, which provide a way to recover the specimens having been subjected to high pressures. Six different experiments are performed on the Omega laser using single-mode tantalum targets at different laser energies. The energy indicates the amount of laser energy that impinges the target. For each target, values for growth factor are obtained by comparing the profile of ripples before and after the experiment. With increasing energy, the growth factor increased.

Engineering simulations are used to interpret and correlate the measurements of growth factor to a measure of strength. In order to validate the engineering constitutive model for tantalum, a series of simulations are performed using the code Eureka, based on the Optimal Transportation Meshfree (OTM) method. Two different configurations are studied in the simulations: RM instabilities in single and multimode ripples. Six different simulations are performed for the single ripple configuration of the RM instability experiment, with drives corresponding to laser energies used in the experiments. Each successive simulation is performed at higher drive energy, and it is observed that with increasing energy, the growth factor increases. Overall, there is favorable agreement between the data from the simulations and the experiments. The peak growth factors from the simulations and the experiments are within 10% agreement. For the multimode simulations, the goal is to assist in the design of the laser driven experiments using the Omega laser. A series of three-mode and four-mode patterns are simulated at various energies and the resulting growth of the RM instability is computed. Based on the results of the simulations, a configuration is selected for the multimode experiments. These simulations also serve as validation for the constitutive model and the material parameters for tantalum that are used in the simulations.

By designing samples with initial perturbations in the form of single-mode and multimode ripples and subjecting these samples to high pressures, the Richtmyer-Meshkov instability is investigated in both laser compression experiments and simulations. By correlating the growth of these ripples to measures of strength, a better understanding of the strength of tantalum at high pressures is achieved.

Diseño de un array de antenas en tecnología microstrip

[ES]Este trabajo de fin de grado trata sobre el diseño de un array de antenas en tecnología microstrip para ser utilizado en la banda de 5 GHz del estándar de tecnologías inalámbricas IEEE 802.11a. Se buscará aplicar la teoría de arrays para conseguir la mayor ganancia posible, pero al mismo tiempo tratando de obtener un gran ancho de banda para que la antena sea óptima dentro de la mayor parte posible de la banda especificada. El proyecto partirá de un único parche microstrip para posteriormente ir evolucionando el diseño hasta llegar a un array de 2x2 elementos. Al primer diseño se le irán añadiendo progresivamente todos los componentes necesarios (red de adaptación, desfasadores, mayor número de parches, etc.) para poder ir estudiando las simulaciones a la vez que el diseño progresa. Todos los diseños se realizarán con el software ADS (Advanced Design System) de la compañía Agilent Technologies. Finalmente se fabricará el array diseñado y se medirá para contrastarlo con las simulaciones.

Análise comparativa in vivo da detecção de lesões de cárie oclusal e proximal por meio de exame visual (ICDAS), exame radiográfico e transiluminação por fibra ótica (FOTI)

O objetivo do presente trabalho foi avaliar in vivo a detecção de cárie através do exame visual ICDAS, transiluminação por fibra ótica combinado ao ICDAS e exame radiográfico. Um total de 2.279 superfícies proximais e cicatrículas e fissuras em incisivos superiores, pré-molares e molares permanentes e 272 superfícies em molares decíduos em72 escolares (8 a 18 anos) foram avaliadas por um examinador treinado. Os sete escores para detecção de cárie primária do sistema visual ICDAS foram aplicados. Dois equipamentos de transiluminação por fibra ótica foram avaliados: FOTI Schott (SCH), com ponta de fibra ótica com 0,5mm de diâmetro, e FOTI Microlux (MIC), com diâmetro da ponta 3 mm. Durante o exame combinado FOTI/ICDAS, a fibra ótica era utilizada tanto para iluminar quanto para transiluminar a superfície sob avaliação. O exame radiográfico (RX) consistiu de radiografias interproximais posteriores e periapicais anteriores. Os exames foram realizados em consultório odontológico após escovação supervisionada. No primeiro dia de exame, o exame visual utilizando o ICDAS era realizado e em seguida, o exame combinado ao MIC ou SCH. Logo após era realizado o exame radiográfico. Após uma semana, novamente o ICDAS era realizado, e em seguida o exame combinado com o equipamento de FOTI não utilizado na semana anterior. Os exames foram repetidos em 10 pacientes após intervalo mínimo de uma semana para avaliação da reprodutibilidade intra-examinador, a qual apresentou valores de 0,95 (ICDAS), 0,94 (MIC), 0,95 (SCH) e 0,99 (RX) pelo kappa ponderado. Em cicatrículas e fissuras de permanentes, o RX julgou que um número maior de superfícies apresentava lesão em dentina (53) do que os outros métodos (34 a 36); porém não detectou nenhuma lesão em esmalte, as quais foram identificadas pelo ICDAS (94), SCH (107) e MIC (91). Em proximais permanentes, a transiluminação por fibra ótica identificou maior número de proximais como lesão em esmalte - 150 (SCH) e 139 (MIC) - do que o exame visual (106), enquanto o RX identificou somente 43. Em oclusais de decíduos, os quatro métodos julgaram um número aproximadamente similar de superfícies sem lesão (52 a 59) ou com lesão em dentina (21 a 26), assim como para lesões proximais em dentina (31 a 36). Entretanto um número reduzido de lesões proximais decíduas em esmalte foi julgado pelo exame radiográfico (3) em comparação com os outros métodos (15 a 16). Em decíduos, o ICDAS e o FOTI combinado ao exame visual julgaram maior número de lesões proximais em esmalte que o exame radiográfico, sendo que número similar de lesões em dentina foram classificadas pelos quatro métodos em oclusais e proximais de molares decíduos. Em cicatrículas e fissuras de permanentes, tanto o exame visual ICDAS quanto sua combinação aos dois equipamentos de transiluminação apresentaram maior similaridade de superfícies julgadas como lesão em esmalte ou como lesão em dentina, enquanto o exame radiográfico classificou mais superfícies como lesão em dentina e nenhuma como lesão em esmalte. A adição da transiluminação por fibra ótica ao exame visual aumentou em um terço a detecção das lesões cariosas proximais julgadas em dentina pelo ICDAS isoladamente e aproximadamente quadruplicou o número daquelas assim classificadas pela avaliação radiográfica em permanentes.

星间激光通信中复合轴系统的带宽设计研究

星间激光通信中，由粗跟踪系统和精跟踪系统组成的复合轴系统完成了系统的大范围、高精度跟踪任务。对复合轴系统进行了基于Z变换的数字模拟以研究其带宽设计。根据计算的卫星轨迹和粗跟踪系统机械误差，得到了粗跟踪系统的带宽设计结果；给出了粗跟踪系统和精跟踪系统的配合工作关系；得到了精跟踪系统的带宽设计结果；最后研究了在中高频扰动下，复合轴系统的带宽设计。以上结果为星间激光通信中的复合轴系统控制系统设计提供了重要依据。

Development of Microfluidic Devices with the Use of Nanotechnology to Aid in the Analysis of Biological Systems Including Membrane Protein Separation, Single Cell Analysis, and Genetic Markers

Computation technology has dramatically changed the world around us; you can hardly find an area where cell phones have not saturated the market, yet there is a significant lack of breakthroughs in the development to integrate the computer with biological environments. This is largely the result of the incompatibility of the materials used in both environments; biological environments and experiments tend to need aqueous environments. To help aid in these development chemists, engineers, physicists and biologists have begun to develop microfluidics to help bridge this divide. Unfortunately, the microfluidic devices required large external support equipment to run the device. This thesis presents a series of several microfluidic methods that can help integrate engineering and biology by exploiting nanotechnology to help push the field of microfluidics back to its intended purpose, small integrated biological and electrical devices. I demonstrate this goal by developing different methods and devices to (1) separate membrane bound proteins with the use of microfluidics, (2) use optical technology to make fiber optic cables into protein sensors, (3) generate new fluidic devices using semiconductor material to manipulate single cells, and (4) develop a new genetic microfluidic based diagnostic assay that works with current PCR methodology to provide faster and cheaper results. All of these methods and systems can be used as components to build a self-contained biomedical device.

A study of flow conditions near the substratum in an experimental channel [Translation from: Verhandlungen der Internationalen Vereinigung fur Theoretische und Angewandte Limnologie 18, 718-725, 1972]

In a slow flow, on a smooth uniform substratum, a limited bed allows the existence of currents slow enough for benthic invertebrates. These conditions rarely occur naturally. The investigations carried out in this work aimed, on an intermediary scale, to define the influence of irregularities in the substratum on flow near the bottom. The substrata used were made of glass marbles. The investigations were carried out in a transparent channel of 70 cm in length and a rectangular section 10 x 5 cm. The data was analysed to study the general evolution of flow in terms of average speeds and the appearance of the turbulence near the bottom.

Preliminary surveys of the fish and fisheries of the Nzoia, Nyando and Sondu Miriu rivers, Kenya

Three Lake Victoria rivers were sampled to assess fish abundance and distribution in preparation for assessment of catches from the river systems. Preliminary fish abundance data indicate that fishing potential upstream is negligible but that important commercial species are present in the downstream floodplain areas. Three catfish species were recorded in the Nzoia river system that have not been found previously in the Kenyan sector of the Lake Victoria system, together with possibly two undescribed Barbus species.

The design and development of the Windermere Profiler. An instrument for measuring how various environmental parameters vary with depth in lakes, reservoirs and rivers

A review article detailing the background, development and functionality of the Windermere Profiler, a multi parameter environmental monitoring instrument for use in lakes, reservoirs and rivers. The article explains the requirement for regular data collection by the Freshwater Biological Association at Windermere. The article covers the requirements of a profiling instrument, the design considerations, the electronic circuitry, the computer program, the operation of the computer software, the profiler in use and further developments to the design. A number of figures and images accompany the article.