Identificação da formação de titanato de bário a partir de mistura reacional calcinada em diferentes temperaturas via difração de raios X, espectroscopia fotoacústica e análise térmica

Os materiais ferroelétricos têm sido utilizados em muitas áreas da tecnologia e da ciência, pois possuem um grande número de aplicações, como: sensores; transdutores; capacitores; dispositivos ópticos; dentre outras. A busca por novos materiais cerâmicos ferroelétricos tem sido grande. Um dos materiais cerâmicos ferroelétricos mais estudados é o titanato de bário (BT). São vários os métodos de produção e caracterização do titanato de bário. Neste trabalho, pós cerâmicos de titanato de bário foram obtidos por reação do estado sólido a partir de misturas reacionais calcinadas em diferentes temperaturas entre 400C e 900C. Foram três as misturas reacionais: não dopadas; dopadas com 1%; e dopadas com 5% de dióxido de cério (CeO2). A identificação da formação do BT, nos pós cerâmicos produzidos, foi feita a partir de três técnicas de caracterização: difração de raios X (DRX); espectroscopia fotoacústica (PAS); e técnicas de análise térmica. Com a técnica DRX, difratogramas mostraram que a plena formação do titanato de bário ocorreu a partir da temperatura de calcinação de 700C. Para a amostra não dopada com cério e calcinada a 800C, houve deslocamento de todos os picos de difração. Nas amostras dopadas com dióxido de cério houve deslocamento de todos os picos de difração, em relação as amostras não dopadas. Observou-se também que nas amostras dopadas com 5% de CeO2, e calcinadas a 700C e 800C, resíduos de dióxido de cério foram observados nos difratogramas. Com a técnica PAS, espectros de absorção foram obtidos. Foi possível observar uma grande diferença de absorção da amostra calcinada a 600 e 630C, indicando a formação do titanato de bário a partir da temperatura de 630C, nas amostras sem a dopagem dióxido de cério. Houve um alargamento nas bandas de absorção a partir da temperatura de 600C, quando o dióxido de cério entrou na matriz. Foi também possível determinar as energias de band-gap das amostras utilizando o método de Tauc. Com as técnicas de análise térmica, em especial através da técnica termogravimétrica (TG/DTG), foi comprovado que até 400C não havia formação de titanato de bário. Visto que nesta temperatura de calcinação houve a maior perda de massa durante a rampa de aquecimento. O início da formação do titanato de bário foi observado a partir da temperatura de calcinação de 500C, assim como nas técnicas DRX e PAS. Portanto, com os resultados apresentados, foi demonstrada a identificação da formação do titanato de bário nas misturas reacionais calcinadas, com auxílio das potencialidades das três técnicas utilizadas.

Avaliação de aditivos para remoção catalítica de SOx em unidades de fcc

Os óxidos de enxofre (SOx) são um dos maiores poluentes atmosféricos e um dos precursores da chuva ácida. Um levantamento feito na Petrobrás mostrou que cerca de 17% dos SOx emitidos numa refinaria são oriundos do processo de FCC. Com o avanço dos controles ambientais, traduzido numa legislação mais restritiva, a técnica de incorporação de aditivos para remoção de SOx em UFCCs apresenta-se como a alternativa de menor custo frente outras tecnologias de abate das emissões de SOx. No presente trabalho, foram estudados aditivos constituídos por compostos derivados de hidrotalcitas com a substituição parcial do magnésio e do alumínio por cobre e/ou manganês, sendo estes impregnados ou não por dióxido de cério. Estes aditivos foram submetidos a testes de desempenho em uma unidade multi-propósito acoplada a um micro-GC/TCD. Em todos os testes, a corrente gasosa para a etapa de adsorção oxidativa foi de 1700 ppm de SO2 e 1,5% O2 em He e, para a etapa de regeneração, 30% H2/He. No primeiro conjunto de testes, realizou-se uma adsorção a 720C de 10 min e regeneração com um patamar a 530C, seguido de um TPR até 800C. Observou-se que as amostras impregnadas com cério apresentaram o melhor desempenho na remoção de SO2, indicando que o cério pode ter um papel de promotor da oxidação de SO2 a SO3. Os resultados do TPR mostram que as amostras com cério e com manganês parecem apresentar menores temperaturas de redução dos sulfatos, apesar das maiores liberações de H2S serem identificadas nas amostras com cobre. No segundo conjunto de testes, a adsorção foi a 720C durante 35 min e a regeneração a 650C por 5 minutos em um patamar de 5 minutos, seguida de um TPR até 800C. Para os tempos de sulfatação curtos (5 e 10 min), os resultados confirmaram o efeito positivo que a incorporação de CeO2 apresenta sobre a adsorção oxidativa do SO2. Todavia, para tempos de reação maiores (35 min), não se observou uma correlação clara entre a composição química do catalisador e a quantidade total de SOx removida. Os aditivos foram ainda testados em ciclos de reação-regeneração em condições equivalentes ao segundo conjunto de testes descrito. De um modo geral, os aditivos que contêm cobre têm uma vida útil superior aos demais, possivelmente, pelo fato do cobre ter importante papel na regeneração do aditivo

On optical reflection at heterojunction interface of thin film solar cells

Heterojunction is an important structure for the development of photovoltaic solar cells. In contrast to homojunction structures, heterojunction solar cells have internal crystalline interfaces, which will reflect part of the incident light, and this has not been considered carefully before though many heterostructure solar cells have been commercialized. This paper discusses the internal reflection for various material systems used for the development of heterostructure-based solar cells. It has been found that the most common heterostructure solar cells have internal reflection less than 2%, while some potential heterojunction solar cells such as ITO/GaAs, ITO/InP, Si/Ge, polymer/semiconductors and oxide semiconductors may have internal reflection as high as 20%. Also it is worse to have a window layer with a lower refractive index than the absorption layer for solar cells. Ignoring this strong internal reflection will lead to severe deterioration and reduction of conversion efficiency; therefore measures have to be taken to minimize or prevent this internal reflection. © 2013 Elsevier B.V.

Flexible conversion ratio fast reactors: Overview

Conceptual designs of lead-cooled and liquid salt-cooled fast flexible conversion ratio reactors were developed. The performance achievable by the unity conversion ratio cores of these reactors was compared to an existing supercritical carbon dioxide-cooled (S-CO2) fast reactor design and an uprated version of an existing sodium-cooled fast reactor. All concepts have cores rated at 2400 MWt. The cores of the liquid-cooled reactors are placed in a large-pool-type vessel with dual-free level, which also contains four intermediate heat exchangers (IHXs) coupling a primary coolant to a compact and efficient supercritical CO2 Brayton cycle power conversion system. The S-CO2 reactor is directly coupled to the S-CO2 Brayton cycle power conversion system. Decay heat is removed passively using an enhanced reactor vessel auxiliary cooling system (RVACS) and a passive secondary auxiliary cooling system (PSACS). The selection of the water-cooled versus air-cooled heat sink for the PSACS as well as the analysis of the probability that the PSACS may fail to complete its mission was performed using risk-informed methodology. In addition to these features, all reactors were designed to be self-controllable. Further, the liquid-cooled reactors utilized common passive decay heat removal systems whereas the S-CO2 uses reliable battery powered blowers for post-LOCA decay heat removal to provide flow in well defined regimes and to accommodate inadvertent bypass flows. The multiple design limits and challenges which constrained the execution of the four fast reactor concepts are elaborated. These include principally neutronics and materials challenges. The neutronic challenges are the large positive coolant reactivity feedback, small fuel temperature coefficient, small effective delayed neutron fraction, large reactivity swing and the transition between different conversion ratio cores. The burnup, temperature and fluence constraints on fuels, cladding and vessel materials are elaborated for three categories of material - materials currently available, available on a relatively short time scale and available only with significant development effort. The selected fuels are the metallic U-TRU-Zr (10% Zr) for unity conversion ratio and TRU-Zr (75% Zr) for zero conversion ratio. The principal selected cladding and vessel materials are HT-9 and A533 or A508, respectively, for current availability, T-91 and 9Cr-1Mo steel for relatively short-term availability and oxide dispersion strengthened ferritic steel (ODS) available only with significant development. © 2009 Elsevier B.V. All rights reserved.

Experimental investigation on submicron rib waveguide microring/racetrack resonators in silicon-on-insulator

in experiment, characteristics of silicon microring/racetrack resonators in submicron rib waveguides have been systematically investigated. It is demonstrated that only a transverse-electric mode is guided for a ratio of slab height to rib height h/H = 0.5. Thus, these microring/racetrack resonators can only function for quasi-transverse-electric mode, while they get rid of transverse-magnetic polarization. Electron beam lithography and inductively coupled plasma etching were employed and improved to reduce side-wall roughness for low propagation loss and high performance resonators. Then, the effects of waveguide dimensions, coupling region design, waveguide roughness, and oxide cladding for the resonators have been considered and analyzed. (C) 2008 Elsevier B.V. All rights reserved.

High quality CeO2 film grown on Si(111) substrate by using low energy dual ion beam deposition technology

By using the mass-analyzed low energy dual ion beam deposition technique, a high quality epitaxial, insulating cerium dioxide thin film with a thickness of about 2000 Angstrom, has been grown on a silicon (111) substrate. The component species, cerium and oxygen, are homogeneous in depth, and have the correct stoichiometry for CeO2. X-ray double-crystal diffraction shows that the full width at half maximum of the (222) and (111) peaks of the film are less than 23 and 32 s, respectively, confirming that the film is a perfect single crystal. (C) 1995 American Institute of Physics.

The structural composite effect of Au-WO3-Al interconnecting electrode on performance of each unit in stacked OLEDs

In this article, we report the effects of the thickness of metal and oxide layers of the Al/WO3/Au interconnecting structure on the electrical and optical characteristics of the and bottom units of the two-unit stacked organic-light-emitting-devices (OLEDs). It is found that light emission performance of the upper unit is sensitive to the transmittance of semitransparent Al/WO3/Au structure, which can be improved by changing the thickness of each layer of the Al/WO3/Au structure. It is important to note that the introduction WO3 between Al and Au significantly enhances the current efficiency of both the upper and bottom units with respect to that of the corresponding Al/Au structure without WO3. In addition, the emission spectra of both the upper and bottom units are narrower than that of the control device due to microcavity effect. Our results indicate that the All WO3/Au interconnecting structure is a good candidate for fabricating independently controllable high efficiency stacked OLEDs.

Self-cleaning perovskite type catalysts for the dry reforming of methane

Gas-to-liquid processes are generally used to convert natural gas or other gaseous hydrocarbons into liquid fuels via an intermediate syngas stream. This includes the production of liquid fuels from biomass-derived sources such as biogas. For example, the dry reforming of methane is done by reacting CH4 and CO2, the two main components of natural biogas, into more valuable products, i.e., CO and H2. Nickel containing perovskite type catalysts can promote this reaction, yielding good conversions and selectivities; however, they are prone to coke laydown under certain operating conditions. We investigated the addition of high oxygen mobility dopants such as CeO2, ZrO2, or YSZ to reduce carbon laydown, particularly using reaction conditions that normally result in rapid coking. While doping with YSZ, YDC, GDC, and SDC did not result in any improvement, we show that a Ni perovskite catalyst (Na0.5La0.5Ni0.3Al0.7O2.5) doped with 80.9 ZrO2 15.2 CeO2 gave the lowest amount of carbon formation at 800 °C and activity was maintained over the operating time.

Micro-scale abrasion behaviour of electroless Ni-P-SiC coating on aluminium alloy

Electroless nickel (EN) and electroless nickel composite (ENC) coatings were deposited on aluminium alloy substrate, LM24. The micro abrasion test was conducted to study the wear behaviour of the coatings with the effect of SiC concentration. Microhardness of the coatings was tested also. The wear scars were analysed using optical microscope and scanning electron microscope (SEM). The wear resistance was found to be improved in composite coating that has higher microhardness as compared to particles free and the bare aluminium substrate. In as-deposited condition for the composite coating, the wear volume increases on increase in SiC percentage in the coating but is found to be minimum for lower SiC percentage. The increase in hardness on heat treatment at 400°C is due to the hardening or grain coarsening with the formation Ni3P.

Nouveaux complexes pinces POCOP, NHCCOP, PIMCOP et PIMIOCOP, et complexes cyclométallés de Ni(II) : synthèse, caractérisation et réactivité.

Cette thèse traite de la chimie des complexes pinces de Ni(II) ainsi que des complexes cyclométallés de Ni(II) comportant au moins un motif phosphinite. Elle se divise en trois parties. La première concerne la synthèse, la caractérisation, le mécanisme de formation et la réactivité des complexes pinces de Ni(II) à base de ligand de type POCOP 1,3-(i-Pr2PO)2C6H4. De nouveaux ligands de type R-(POCOP) = κP,κC,κP-{Rn-2,6-( R'2PO)2C6H4-n}; Rn = 4-OMe, 4-Me, 4-CO2Me, 3-OMe, 3- CO2Me, 3,5-t-Bu2 ; R' = i-Pr, t-Bu ont été synthétisés suite à l'addition de chlorophosphine ClPR'2 à une solution de résorcinol ou dérivés en présence de base. La synthèse des complexes R-(POCOP)Ni(Br) s'effectue à partir du ligand correspondant en présence de base, et de {NiBr2(NCiPr)}n. Ce nouveau précurseur de nickel est synthétisé à partir de brome de nickel métallique dans l'isobutyronitrile. Il est stable sous atmosphère inerte et sa solubilité dans les solvants polaires permet d'étudier les synthèses des complexes en milieu homogène. Le mécanisme de formation des complexes portant des ligand pinces (PCsp3P) 1,3-(i- Pr2PCH2CH2)2CH2, (POCsp3OP) 1,3-(i-Pr2POCH2)2CH2, (PCsp2P) 1,3-(i- Pr2PCH2)2C6H4, Rn-(POCsp2OP) 1,3-(i-Pr2PO)2C6H4-n via nickellation du lien C-H a été investigué avec une méthode de réaction de compétition. Cette étape a été déterminée comme étant de nature électrophile. Les complexes résultants ont été complètement caractérisés. Une corrélation a notamment été effectuée entre le déplacement chimique du Cipso en spectroscopie RMN 13C et le potentiel d'oxydation Eox en voltamétrie cyclique. Une nouvelle méthode de synthèse directe verte "one pot" a été mise en place. En faisant réagir à 75 °C un mélange hétérogène de II résorcinol, de chlorodiisopropylphosphine et de nickel métallique en poudre, on obtient le complexes pince (POCOP)Ni(Cl) avec des rendements allant jusqu'à 93%. La réactivité de ces complexes POCOP a été investiguée pour des réactions de fluorination et trifluorométhylation des halogénures d'alkyle. La synthèse du (POCOP)Ni(F) a lieu à partir de précurseur (POCOP)Ni(X) (X=Br, Cl), en présence d'un large excès de fluorure d'argent AgF. Ce complexe catalyse la fluorination du bromure de benzyle et peut être converti en (POCOP)Ni(CF3) en présence de réactif du Ruppert, Me3SiCF3. La réaction entre (POCOP)Ni(CF3) et le bromure de benzyle dans les solvants aromatiques mène à la conversion totale du complexe en (POCOP)Ni(Br) et à l'inattendue benzylation du solvant aromatique utilisé. La seconde partie concerne la synthèse des nouveaux complexes non symétriques à base de ligands comportant un motif imidazolo-phosphine (PIMCOP) 3-[2-(R2P)-C3H2N2]-(R2PO)-C6H3, imidazoliophosphine (PIMIOCOP) 3-[2-(R2P)-3- (CH3)-C3H2N2]-(R2PO)-C6H3] et carbène N-hétérocyclique (NHCCOP). La double déprotonation du 3-hydroxyphenyl-imidazole suivi de l'addition de deux équivalents de chlorodiphenylphosphine mène à l'obtention du ligand PIMCOP 3-[3-(CH3)- C3H2N2]-(R2PO)-C6H3. L'étape de nickellation a lieu comme dans le cas des composés (POCOP)Ni. La méthylation du motif imidazole du (PIMCOP)Ni(Br) par le triflate de méthyle MeOTf, donne le dérivé (PIMIOCOP)Ni(Br). Ce dernier est converti en (NHCCOP)Ni(Br) après l'addition de chlorure de tétraéthylamonium NEt4Cl. Les analogues i-Pr2P de ces complexes sont synthétisés en remplaçant ClPPh2 par ClPiPr2. On obtient les espèces cationiques [(PIMCOP)Ni(NCCH3)][OTf], [(PIMIOCOP)Ni(NCCH3)][OTf]2 et III [(NHCCOP)Ni(NCCH3)][OTf] suite à l'addition en solution dans l'acétonitrile de triflate d'argent AgOTf. Ces espèces ont été utilisés comme catalyseurs pour la synthèse d'amidine à partir de benzonitrile et de diverse amines aliphatiques. Enfin des complexes orthonickellés trans-Ni[(ĸ2-P,C-P(OC6H4)-(iPr2)( iPr2P(OC6H5))]Br à base de phosphinite ont été synthétisés et caractérisés. Les ligands sont synthétisés par réaction d'un phénol et de chlorodiisopropylphosphine en présence de base. L'ajout de {NiBr2(NCiPr)}n et de triéthylamine permet l'orthométallation via une étape de nickellation C-H. Un intermédiaire trans- [NiBr2{PiPr2(OC6H5)}2] de cette réaction a été isolé. Le complexe dimère peut réagir avec des espèces électrophiles mener à l'ortho-fonctionnalisation de la phosphinite.

Lier la spéciation chimique du cérium à sa biodisponibilité sous différentes conditions environnementales

L’étude qui suit porte sur l’évaluation du risque écotoxicologique du cérium, l’élément le plus exploité de la famille des lanthanides. La présence grandissante de ce métal dans notre quotidien rend possible son relargage dans l’environnement. Il est donc primordial de comprendre l’impact qu’il aura sur les organismes vivant dans un système aquatique. Une approche centrée sur le modèle du ligand biotique a été utilisée pour évaluer adéquatement l’interaction entre le cérium et un ligand biotique à la surface de l’algue unicellulaire Chlamydomonas reinhardtii. Pour mener une étude sur le risque écotoxicologique d’un élément métallique il faut, avant tout, comprendre la spéciation (répartition sous ses différentes formes chimiques) de l’élément en question. Les premières sections du mémoire vont donc traiter des expériences qui ont été menées pour évaluer la spéciation du cérium dans les conditions expérimentales d’exposition à C. reinhardtii. Il sera question de faire la distinction entre la forme particulaire du métal et sa forme dissoute, de caractériser ces changements par spectroscopie ainsi que d’évaluer le pouvoir complexant de la matière organique naturelle. Les résultats montrent une importante déplétion du métal dissout en solution à pH neutre et basique et une forte interaction avec la matière organique naturelle, peu importe le pH de la solution. Ensuite, les expériences de bioaccumulation seront expliquéesen comparant l’effet du pH, de la présence d’un ion compétiteur et de la présence de matière organique naturelle sur les paramètres d’internalisation du cérium. Les résultats indiquent qu’à pH acide, le comportement du cérium est plus prévisible qu’à pH neutre. Néanmoins, en tenant compte de la complexité des milieux naturels, l’interaction du métal avec les molécules complexantes va diminuer son risque d’interaction avec un organisme vivant.

Mg citrate found more bioavailable than other Mg preparations in a randomised, double-blind study

Published data on the bioavailability of various Mg preparations is too fragmented and scanty to inform proper choice of Mg preparation for. clinical studies. In this study, the relative bioavailability of three preparations of Mg (amino-acid chelate, citrate and oxide) were compared at a daily dose of 300 mg of elemental Mg in 46 healthy individuals. The study was a randomised, double-blind, placebo-controlled, parallel intervention, of 60 days duration. Urine, blood and saliva samples were taken at baseline, 24 h after the first Mg supplement was taken ('acute' supplementation) and after 60 days of daily Mg consumption ('chronic' supplementation). Results showed that supplementation of the organic forms of Mg (citrate and amino-acid chelate) showed greater absorption (P = 0.033) at 60 days than MgO, as assessed by the 24-h urinary Mg excretion. Mg citrate led to the greatest mean serum Mg concentration compared with other treatments following both acute (P = 0.026) and chronic (P = 0.006) supplementation. Furthermore, although mean erythrocyte Mg concentration showed no differences among groups, chronic Mg citrate supplementation resulted in the greatest (P = 0.027) mean salivary Mg concentration compared with all other treatments. Mg oxide supplementation resulted in no differences compared to placebo. We conclude that a daily supplementation with Mg citrate shows superior bioavailability after 60 days of treatment when compared with other treatments studied.

Chiral molecules on surfaces

chiral molecules can modify surfaces in many ways. Long-range chiral structures can be induced by local chirality, which can act as templates stereo-directing other molecules. Such templates are either based on the arrangement of molecules alone or involve reconstruction of the substrate suface. Stereo-direction can also be achieved buy direct local interaction between chiral moleculesx. Even the adsorption of achiral molecules onto achiral surfaces can induce local chirality due to a reduction ofsymmetry in the presence of the surface. Intrinsically chiral metal and oxide surfaces can act as templates for enantioselective adsorption and surface reactions without any surface modification.

Oxidatively drying coating composition

coating composition comprising an oxidatively drying coating binder and a chelate comprising at least one group according to the following formula (I): forming a complex with a metal ion, A1 and A2 both being an aromatic residue, R1 and R3 being covalently bonded groups, and R2 being a divalent organic radical, wherein at least one solubilizing group is coivalently bonded to the chelating compound. The solubilizing group is a non-polar group, preferable an aliphatic group having at least four carbon atoms, covalently bonded to A1 and/or A2. The metal ion is a divalent ion of a metal selected from the group of manganese, cobalt, copper, lead, zirconium, iron, lanthanium, cerium, vanadium, and clacium or a trivalent ion of a metal selected from the group of manganese, cobalt, lead, zirconium, iron, lanthanium, cerium, and vanadium, combined with a monovalent counterion.

Resposta de plântulas de arroz cv. brs-soberana à aplicação de zinco via semente

A cultura do arroz constitui um dos principais cereais que apresenta alta resposta à aplicação de zinco, constituindo um dos principais cereais em que isso ocorre. Objetivou-se, no presente trabalho, avaliar a aplicação de zinco em sementes, a partir de duas fontes, sobre a nutrição e o crescimento inicial da cultura do arroz cultivar BRS-Soberana. O delineamento experimental utilizado foi o inteiramente casualizado, em três repetições. Os tratamentos foram cinco doses 1,0; 2,0; 4,0 e 8,0g de Zn por kg de semente, das fontes sulfato e óxido, além da testemunha. Após 30 dias da semeadura, avaliou-se a matéria seca (parte aérea e raiz) e o teor e acúmulo de zinco nas plantas. O sulfato de zinco não diferenciou ao óxido para produção de matéria seca total nas plântulas de arroz, entretanto, proporcionou maior absorção de Zn. A aplicação de zinco na forma de sulfato e óxido, na dose de 8g Zn.kg-1 de semente proporcionou maior produção de matéria seca atingindo teor do nutriente, na parte aérea de 281 e 163 mg.kg-1, respectivamente.