Treatment of oily wastewater by ultrafiltration: The effect of different operating and solution conditions

In many industries, such as petroleum production, and the petrochemical, metal, food and cosmetics industries, wastewaters containing an emulsion of oil in water are often produced. The emulsions consist of water (up to 90%), oils (mineral, animal, vegetable and synthetic), surfactants and other contaminates. In view of its toxic nature and its deleterious effects on the surrounding environment (soil, water) such wastewater needs to be treated before release into natural water ways. Membrane-based processes have successfully been applied in industrial applications and are considered as possible candidates for the treatment of oily wastewaters. Easy operation, lower cost, and in some cases, the ability to reduce contaminants below existing pollution limits are the main advantages of these systems. The main drawback of membranes is flux decline due tofouling and concentration polarisation. The complexity of oil-containing systems demands complementary studies on issues related to the mitigation of fouling and concentration polarisation in membranebased ultrafiltration. In this thesis the effect of different operating conditions (factors) on ultrafiltration of oily water is studied. Important factors are normally correlated and, therefore, their effect should be studied simultaneously. This work uses a novel approach to study different operating conditions, like pressure, flow velocity, and temperature, and solution properties, like oil concentration (cutting oil, diesel, kerosene), pH, and salt concentration (CaCl2 and NaCl)) in the ultrafiltration of oily water, simultaneously and in a systematic way using an experimental design approach. A hypothesis is developed to describe the interaction between the oil drops, salt and the membrane surface. The optimum conditions for ultrafiltration and the contribution of each factor in the ultrafiltration of oily water are evaluated. It is found that the effect on permeate flux of the various factors studied strongly depended on the type of oil, the type of membrane and the amount of salts. The thesis demonstrates that a system containing oil is very complex, and that fouling and flux decline can be observed even at very low pressures. This means that only the weak form of the critical flux exists for such systems. The cleaning of the fouled membranes and the influence of different parameters (flow velocity, temperature, time, pressure, and chemical concentration (SDS, NaOH)) were evaluated in this study. It was observed that fouling, and consequently cleaning, behaved differently for the studied membranes. Of the membranes studied, the membrane with the lowest propensity for fouling and the most easily cleaned was the regenerated cellulose membrane (C100H). In order to get more information about the interaction between the membrane and the components of the emulsion, a streaming potential study was performed on the membrane. The experiments were carried out at different pH and oil concentration. It was seen that oily water changed the surface charge of the membrane significantly. The surface charge and the streaming potential during different stages of filtration were measured and analysed being a new method for fouling of oil in this thesis. The surface charge varied in different stages of filtration. It was found that the surface charge of a cleaned membrane was not the same as initially; however, the permeability was equal to that of a virgin membrane. The effect of filtration mode was studied by performing the filtration in both cross-flow and deadend mode. The effect of salt on performance was considered in both studies. It was found that salt decreased the permeate flux even at low concentration. To test the effect of hydrophilicity change, the commercial membranes used in this thesis were modified by grafting (PNIPAAm) on their surfaces. A new technique (corona treatment) was used for this modification. The effect of modification on permeate flux and retention was evaluated. The modified membranes changed their pore size around 33oC resulting in different retention and permeability. The obtained results in this thesis can be applied to optimise the operation of a membrane plant under normal or shock conditions or to modify the process such that it becomes more efficient or effective.

Strategic choices and performance – an empirical analysis of largest European and North American energy companies

Energy industry has gone through major changes globally in past two decades. Liberalization of energy markets has led companies to integrate both vertically and horizontally. Growing concern on sustainable development and aims to decrease greenhouse gases in future will increase the portion of renewable energy in total energy production. Purpose of this study was to analyze using statistical methods, what impacts different strategic choices has on biggest European and North American energy companies’ performance. Results show that vertical integration, horizontal integration and use of renewable energy in production had the most impact on profitability. Increase in level of vertical integration decreased companies’ profitability, while increase in horizontal integration improved companies’ profitability. Companies that used renewable energy in production were less profitable than companies not using renewable energy.

Effects of Surface Properties and Wood Modification into Direct Printing on Wood

Building industry is a high volume branch which could provide prominent markets for wood based interior decoration solutions. Competition in interior decoration markets requires versatility in appearance. Versatility in wood appearance and added value could be achieved by printing grain patterns of different species or images directly onto wood. The problem when planning wood printing’s implementing into durable applications is basically how to transfer a high quality image or print sustainably onto wood, which is porous, heterogeneous, dimensionally unstable, non-white and rough. Wood preservation or treating, and modification can provide durability against degradation but also effect to the surface properties of wood which will effect on printability. Optimal adhesion is essential into print quality, as too high ink absorbance can cause spreading and too low ink absorbance cause pale prints. Different printing techniques have different requirements on materials and production. The direct printing on wood means, that intermedias are not used. Printing techniques with flexible printing plates or in fact non-impact techniques provide the best basis for wood printing. Inkjet printing of wood with different mechanical or chemical surface treatments, and wood plastic composite material gave good results that encourage further studies of the subject. Sanding the wood surface anti-parallel to the grain gave the best overall printing quality. Spreading parallel to the grain could not be avoided totally, except in cases where wood was treated hydrophobic so adhesion of the ink was not sufficient. Grain pattern of the underlying wood stays clearly visible in the printed images. Further studies should be made to fine tune the methods that already gave good results. Also effects of moisture content of wood, different inks, and long-term exposure to UV-radiation should be tested.

In vitro activity of essential oils of Lippia sidoides and Lippia gracilis and their major chemical components against Thielaviopsis paradoxa, causal agent of stem bleeding in coconut palms

Essential oils of Lippia sidoides, Lippia gracilis and their main chemical components were investigated for in vitro control of Thielaviopsis paradoxa. Mycelial growth and a number of pathogen conidia were inhibited by the essential oil of L. sidoides at all concentrations tested (0.2; 0.5; 1.0; 3.0 µL mL-1). L. sidoides oil contained 42.33% thymol and 4.56% carvacrol, while L. gracilis oil contained 10% thymol and 41.7% carvacrol. Mycelial growth and conidial production of T. paradoxa were completely inhibited by thymol at a 0.3 µL m-1 concentration. The results suggest that thymol could potentially be used for controlling coconut stem bleeding.

A FACTORIAL DESIGN APPLIED TO THE STUDY OF CHROMIUM TOXICITY ON THE GLUTATHIONE LEVELS OF Brachiaria brizantha AND Brachiaria ruziziensis SEEDLINGS

Chromium toxicity affects redox reactions within plant cells, generating detrimental reactive oxygen species. Glutathione is an antioxidant peptide and also a substrate for the production of phytochelatins, which are chelating peptides reported to mitigate Cr3+ toxicity in plants. In this study, Brachiaria brizantha (B. brizantha) and Brachiaria ruziziensis (B. ruziziensis) seedlings were evaluated for physiological responses and glutathione production following the addition of zero or 5 mg L-1 Cr3+ to the nutrient solution. Glutathione levels were determined by colorimetric analysis at 412 nm using 5,5'-dithio-bis(2-nitrobenzoic acid) as a chromophore reagent and recovery with glutathione reductase (with evaluations at days 10 and 20 of continuous growth). The assessments were carried out in a completely randomized design with 2 authentic replications, and arranged in a 23 factorial. Cr3+ caused an average increase of 0.76 mg g-1 in the initial glutathione content. However, by day 20 there was an average reduction of 3.63 mg g-1. Chromium-affected physiological detrimental responses, albeit detected in both species, were less-pronounced in B. ruziziensis, along with a much higher level of glutathione. This study indicates that B. ruziziensis has a greater tolerance for chromium toxicity than B. brizantha, and that glutathione is likely to be involved in the mitigation of chromium stress in B. ruziziensis.

Screening of sweet sorghum accessions for inhibition of secondary sporulation and saccharide measurements in honeydew of Claviceps africana

Certain sweet sorghums (Sorghum bicolor) inhibit the secondary sporulation of Claviceps africana, which occurs on exuded ergot honeydew when the parasite is supplied with excess sucrose, which is then transformed to unique free oligosaccharides fructosyl - mannitol and difructosyl - mannitol with spore germination inhibiting properties. Five accessions (BRA-035726-SUGAR DRIP, BRA-035696-THEIS, BRA-036013-MN-4578, BRA-035947-MN-4418 and CMSXS-633) of sweet sorghum were selected among 50 evaluated. These five accessions failed to support secondary sporulation on the "honeydew" exuded from infected florets. There was a higher concentration (%w/v) of the free oligosaccharides on the honeydew of these accessions when compared to a hybrid male-sterile grain sorghum. Therefore, a possible strategy would be seek to incorporate a sweet character into "A" lines for hybrid seed production in order to restrict secondary disease spread.

Susceptibility of fruits of the 'Valência' and 'Natal' sweet orange varieties to Guignardia citricarpa and the influence of the coexistence of healthy and symptomatic fruits

The importance of the presence of symptomatic fruits with citrus black symptoms (CBS) on the disease severity level in subsequent crop production was assessed in an orchard planted with Valência and Natal sweet orange varieties. Additionally, the period of susceptibility of the fruits of these varieties was evaluated. Fruits were covered with paper bags at the stage of 75% fallen petals and were then exposed to natural infection at weekly intervals, from October 2000 to April 2001. This process was carried out in plants where the fruits from the previous harvest had been picked as well as in plants where fruits remained until natural drop. The evaluation of disease severity used a scale that varied from 0 (absence of symptoms) to 6 (severe symptoms). It was observed that, for the Valência and Natal varieties, conidia of Phyllosticta citricarpa that had formed on the lesions of fruits from the previous harvest did not significantly increase the severity of disease on the fruits of the subsequent harvest period. In this study, the protection of the fruits until 10 weeks after petal drop did not affect the number of lesions, indicating that ascospore discharges after that date were, probably, responsible for disease severity. Fruits exposed between the 20th and 24th week after 75% of the petals had fallen were symptomatic, indicating that, at this stage, the fruits were still susceptible to the pathogen.

Effect of alcohol concentration and electrode composition on the ethanol electrochemical oxidation

The electrochemical oxidation on platinum and platinum rhodium bimetallic electrodes was studied by Differential Electrochemical Mass Spectrometry for several ethanol concentrations in solution. It is found that increasing the ethanol concentration the production of the partially oxidized products (acetaldehyde) increases as the concentration increases. On the other hand, addition of 25% at. of rhodium increases the full oxidation to CO2. Another interesting result observed is a correlation between the intensity of the dehydrogenations peak at 0.3 V vs. RHE and the CO2 yield for the different ethanol concentration studied.

Analysis of the structure and vibrational spectra of glucose and fructose

Molecular modelling using semiempirical methods AM1, PM3, PM5 and, MINDO as well as the Density Functional Theory method BLYP/DZVP respectively were used to calculate the structure and vibrational spectra of d-glucose and d-fructose in their open chain, alpha-anomer and beta-anomer monohydrate forms. The calculated data show that both molecules are not linear; ground state and the number for the point-group C is equal to 1. Generally, the results indicate that there are similarities in bond lengths and vibrational modes of both molecules. It is concluded that DFT could be used to study both the structural and vibrational spectra of glucose and fructose.

Evaluation of the dioxin and furan formation thermodynamics in combustion processes of urban solid wastes

Specific combustion programs (Gaseq, Chemical equilibria in perfect gases, Chris Morley) are used to model dioxin and formation in the incineration processes of urban solid wastes. Thanks to these programs, it is possible to establish correlations with the formation mechanisms postulated in literature on the subject. It was found that minimum oxygen quantities are required to obtain a significant formation of these compounds and that more furans than dioxins are formed. Likewise, dioxin and furan formation is related to the presence of carbon monoxide, and dioxin and furan distribution among its different compounds depends on the chlorine and hydrogen relative composition. This is due to the fact that an increased chlorine availability leads to the formation of compounds bearing a higher chlorine concentration (penta-, hexa-, hepta-, and octachlorides), whereas an increased hydrogen availability leads to the formation of compounds bearing a lower chlorine number (mono, di-, tri-, and tetrachlorides).

On the development of object functions and restrictions for shapes made with a turret punch press

This study presents the information required to describe the machine and device resources in the turret punch press environment which are needed for the development of the analysing method for automated production. The description of product and device resources and their interconnectedness is the starting point for method comparison the development of expenses, production planning and the performance of optimisation. The manufacturing method cannot be optimized unless the variables and their interdependence are known. Sheet metal parts in particular may then become remarkably complex, and their automatic manufacture may be difficult or, with some automatic equipment, even impossible if not know manufacturing properties. This thesis consists of three main elements, which constitute the triangulation. In the first phase of triangulation, the manufacture occuring on a turret punch press is examined in order to find the factors that affect the efficiency of production. In the second phase of triangulation, the manufacturability of products on turret punch presses is examined through a set of laboratory tests. The third phase oftriangulation involves an examination of five industry parts. The main key findings of this study are: all possible efficiency in high automation level machining cannot be achieved unless the raw materials used in production and the dependencies of the machine and tools are well known. Machine-specific manufacturability factors for turret punch presses were not taken into account in the industrial case samples. On the grounds of the performed tests and industrial case samples, the designer of a sheet metal product can directly influence the machining time, material loss, energy consumption and the number of tools required on a turret punch press by making decisions in the way presented in the hypothesis of thisstudy. The sheet metal parts to be produced can be optimised to bemanufactured on a turret punch press when the material to be used and the kinds of machine and tool options available are known. This provides in-depth knowledge of the machine and tool properties machine and tool-specifically. None of the optimisation starting points described here is a separate entity; instead, they are all connected to each other.

Delay reduction in courts of justice – possibilities and challenges of process improvement in professional public organizations

Delays in the justice system have been undermining the functioning and performance of the court system all over the world for decades. Despite the widespread concern about delays, the solutions have not kept up with the growth of the problem. The delay problem existing in the justice courts processes is a good example of the growing need and pressure in professional public organizations to start improving their business process performance.This study analyses the possibilities and challenges of process improvement in professional public organizations. The study is based on experiences gained in two longitudinal action research improvement projects conducted in two separate Finnish law instances; in the Helsinki Court of Appeal and in the Insurance Court. The thesis has two objectives. First objective is to study what kinds of factors in court system operations cause delays and unmanageable backlogs and how to reduce and prevent delays. Based on the lessons learned from the case projects the objective is to give new insights on the critical factors of process improvement conducted in professional public organizations. Four main areas and factors behind the delay problem is identified: 1) goal setting and performance measurement practices, 2) the process control system, 3) production and capacity planning procedures, and 4) process roles and responsibilities. The appropriate improvement solutions include tools to enhance project planning and scheduling and monitoring the agreed time-frames for different phases of the handling process and pending inventory. The study introduces the identified critical factors in different phases of process improvement work carried out in professional public organizations, the ways the critical factors can be incorporated to the different stages of the projects, and discusses the role of external facilitator in assisting process improvement work and in enhancing ownership towards the solutions and improvement. The study highlights the need to concentrate on the critical factors aiming to get the employees to challenge their existing ways of conducting work, analyze their own processes, and create procedures for diffusing the process improvement culture instead of merely concentrating of finding tools, techniques, and solutions appropriate for applications from the manufacturing sector

18F-Labeled Presynaptic Dopaminergic Tracers. Synthesis, Radiochemical Analyses, and Preclinical Evaluation of [18F]FDOPA and [18F]CFT

Dysfunction of the dopaminergic system in brain is involved in several pathological conditions such as Parkinson’s disease and depression. 2β-Carbomethoxy-3β-(4-[18F] fluorophenyl)tropane ([18F]CFT) and 6-[18F]fluoro-L-dopa ([18F]FDOPA) are tracers for imaging the dopaminergic function with positron emission tomography (PET). Peripheral uptake of [18F]FDOPA is also used in the localization and diagnosis of neuroendocrine tumors. [18F]FDOPA and [18F]CFT can be synthesized by electrophilic fluorodestannylation. However, the specific radioactivity (SA) in the electrophilic fluorination is low with traditional synthetic methods. In this study, [18F]FDOPA and [18F]CFT were synthesized using post-target-produced [18F]F2 as an electrophilic fluorination agent. With this method, tracers are produced with sufficient SA for neuroreceptor studies. Specific aims in this study were to replace Freon-11 in the production of [18F]FDOPA due to the ozone depleting properties of this solvent, to determine pharmacological specificity and selectivity of [18F]CFT with respect to monoamine transporters, and to compare the ability of these tracers to reflect the degree of nigral neuronal loss in rats in which the dopaminergic system in the brain had been unilaterally destroyed by 6- OHDA. Post-target-produced [18F]F2 was successfully used in the production of [18F]FDOPA and [18F]CFT. The SA achieved was substantially higher than in previous synthetic methods. Deuterated compounds, CD2Cl2, CDCl3 and C3D6O, were found to be suitable solvents for replacing Freon-11. Both [18F]FDOPA and [18F]CFT demonstrated nigrostriatal dopaminergic hypofunction and correlated with the number of nigral dopaminergic neurons in the 6-OHDA lesioned rat. However, the dopamine transporter (DAT) tracer [18F]CFT was more sensitive than the dopamine synthesis tracer [18F]FDOPA in detecting these defects because of the higher non-specific uptake of [18F]FDOPA. [18F]CFT can also be used for imaging the norepinephrine transporter (NET) because of the specific uptake into the locus coeruleus. The observation that [18F]CFT exhibits specific uptake in the pancreas warrants further studies in humans with respect to potential utility in pancreatic imaging

Removal of organic matter and nutrients from slaughterhouse wastewater by using Eichhornia crassipes and evaluation of the generated biomass composting

The objective of this research was to evaluate the performance of the aquatic macrophyte Eichhornia crassipes applied in situ in a slaughter house treatment system, located in the west of the Paraná state, Brazil, regarding the nutrients removal and organic matter. Moreover, it aimed to obtain data from the production, management and composting practices of the biomass generated in the system. During 11 months of macrophytes development, physic and chemical parameters were monitored and plant density was controlled by periodical removal of excess biomass, which was weekly monitored and it is expressed in kg of aquatic plant per m² covered area. The degradation of the macrophytes removed from the treatment system was evaluated at the pilot scale in eight composting piles of 0.60 m³ that underwent four different treatments and two repetitions: T1 - water hyacinth (Eichhornia crassipes); T2 - water hyacinth and swine excrement (7:1), T3 - water hyacinth, swine excrement and earth (7:1:0,67), and T4 - water hyacinth, swine excrement and cellulosic gut (7:1:0,67), for a period of 90 days. The results indicated maximum removal efficiencies of 77.2% for COD; 77.8% for BOD, 87.9% for total nitrogen, 47.5% for ammonia nitrogen and 38.9% for total phosphorus for a five-day retention time. For biomass stabilization by composting, considering the C:N ratio as an indicator of compost maturity, it was observed that treatment T4 resulted in the shortest stabilization period (60 days). No difference was verified in the biostabilization rates at 5% level by the F test.

Operational performance of the mechanized and semi-mechanized potato harvest

Potato is an important crop plant throughout the world. Harvesting is a fundamental step in its production system. Maybe, it is the most complex and expensive operation. Thus, the objective of this work was to compare the cost of the mechanized and semi-mechanized harvest, the operational capacity and the production losses during the potato harvest process. The work was accomplished in a commercial farming, cultivated under pivot system, in the municipal district of Perdizes - MG, Brazil. A completely randomized design with two treatments was used: mechanized and semi-mechanized harvest. The mechanized harvest used a self-propelled harvester. In the semi-automated harvest, a digger mounted on tractor was used and the potato was manually harvested. It was concluded that the cost of mechanized harvest was 49.03% lower than the cost of semi-mechanized harvest. On average, the harvester had a work for 23 workers in manual harvest. Mechanized harvest showed losses of 2.35% of potato yield, while the semi-mechanized harvest showed losses of 6.32%.