Use of Photovoltaic on an E-bike? : A Feasibility Study

In recent years the number of bicycles with e-motors has been increased steadily. Within the pedelec – bikes where an e-motor supports the pedaling – a special group of transportation bikes has developed. These bikes have storage boxes in addition to the basic parts of a bike. Due to the space available on top of those boxes it is possible to install a PV system to generate electricity which could be used to recharge the battery of the pedelec. Such a system would lead to grid independent charging of the battery and to the possibility of an increased range of motor support. The feasibility of such a PV system is investigated for a three wheeled pedelec delivered by the company BABBOE NORDIC.The measured data of the electricity generation of this mobile system is compared to the possible electricity generation of a stationary system.To measure the consumption of the pedelec different tracks are covered, and the energy which is necessary to recharge the bike battery is measured using an energy logger. This recharge energy is used as an indirect measure of the electricity consumption. A PV prototype system is installed on the bike. It is a simple PV stand alone system consisting of PV panel, charge controller with MPP tracker and a solar battery. This system has the task to generate as much electricity as possible. The produced PV current and voltage aremeasured and documented using a data logger. Afterwards the average PV power is calculated. To compare the produced electricity of the on-bike system to that of a stationary system, the irradiance on the latter is measured simultaneously. Due to partial shadings on the on-bike PV panel, which are caused by the driver and some other bike parts, the average power output during riding the bike is very low. It is too low to support the motor directly. In case of a similar installation as the PV prototype system and the intention always to park the bike on a sunny spot an on-bike system could generate electricity to at least partly recharge a bike battery during one day. The stationary PV system using the same PV panel could have produced between 1.25 and 8.1 times as much as the on-bike PV system. Even though the investigation is done for a very specific case it can be concluded that anon-bike PV system, using similar components as in the investigation, is not feasible to recharge the battery of a pedelec in an appropriate manner. The biggest barrier is that partial shadings on the PV panel, which can be hardly avoided during operation and parking, result in a significant reduction of generated electricity. Also the installation of the on-bike PV system would lead to increased weight of the whole bike and the need for space which is reducing the storage capacity. To use solar energy for recharging a bike battery an indirect way is giving better results. In this case a stationary PV stand alone system is used which is located in a sunny spot without shadings and adjusted to use the maximum available solar energy. The battery of the bike is charged using the corresponding charger and an inverter which provides AC power using the captured solar energy.

Cloud computing - Moving to the cloud

Cloud computing innebär användning av datorresurser som är tillgängliga via ett nätverk, oftast Internet och är ett område som har vuxit fram i snabb takt under de senaste åren. Allt fler företag migrerar hela eller delar av sin verksamhet till molnet. Sogeti i Borlänge har behov av att migrera sina utvecklingsmiljöer till en molntjänst då drift och underhåll av dessa är kostsamma och tidsödande. Som Microsoftpartners vill Sogeti använda Microsoft tjänst för cloud computing, Windows Azure, för detta syfte. Migration till molnet är ett nytt område för Sogeti och de har inga beskrivningar för hur en sådan process går till. Vårt uppdrag var att utveckla ett tillvägagångssätt för migration av en IT-lösning till molnet. En del av uppdraget blev då att kartlägga cloud computing, dess beståndsdelar samt vilka för- och nackdelar som finns, vilket har gjort att vi har fått grundläggande kunskap i ämnet. För att utveckla ett tillvägagångssätt för migration har vi utfört flera migrationer av virtuella maskiner till Windows Azure och utifrån dessa migrationer, litteraturstudier och intervjuer dragit slutsatser som mynnat ut i ett generellt tillvägagångssätt för migration till molnet. Resultatet har visat att det är svårt att göra en generell men samtidigt detaljerad beskrivning över ett tillvägagångssätt för migration, då scenariot ser olika ut beroende på vad som ska migreras och vilken typ av molntjänst som används. Vi har dock utifrån våra erfarenheter från våra migrationer, tillsammans med litteraturstudier, dokumentstudier och intervjuer lyft vår kunskap till en generell nivå. Från denna kunskap har vi sammanställt ett generellt tillvägagångssätt med större fokus på de förberedande aktiviteter som en organisation bör genomföra innan migration. Våra studier har även resulterat i en fördjupad beskrivning av cloud computing. I vår studie har vi inte sett att någon tidigare har beskrivit kritiska framgångsfaktorer i samband med cloud computing. I vårt empiriska arbete har vi dock identifierat tre kritiska framgångsfaktorer för cloud computing och i och med detta täckt upp en del av kunskapsgapet där emellan.

Jämförelsestudie avseende stomsystem : Ramverk eller fackverk/balk/pelar-system

Projektet omfattade en jämförelsestudie avseende stomsystem. Studien undersökte ramverk och fackverk/balk/pelar-system och genomfördes självständigt med stöttning av Ramböll AB´s kontor i Falun. Syftet var främst att undersöka vilka skillnader det finns mellan tvåledsramar och fackverk/balk/pelar-system för lätta hallbyggnader och försöka få klarhet i varför fackverk/balk/pelar-system är det dominerande systemet i Sverige eftersom övriga Europa har tagit en annan utveckling och domineras av tvåledsramar. Studien undersöker skillnaderna mellan systemen i en hallbyggnad med förutbestämda mått i stål.Inledningsvis gjordes en litteraturstudie för att få en bredare bakgrund av systemen och en bättre förståelse om förutsättningarna för varje system. Efter litteraturstudien kunde sedan ett typhus och beräkningsunderlag för jämförelsestudien tas fram. Även en enkätstudie gjordes med syftet att skapa en tydlig bild av vilket stomsystem konstruktörer i Sverige oftast väljer och varför. Resultatet av studien visade att tvåledsramar ger en ökad kostnad jämfört med fackverk/balk/pelar-system i materialåtgång och framställning samt att beräkningarna blir mer komplicerade. Skulle fortsatta studier göras med dessa system i byggnader med andra mått skulle det kanske gå att få fram speciella mått på byggnader där kostnaden för tvåledsramar blir densamma som för fackverk/balk/pelar-system och därför är ett likvärdigt alternativ som stomsystem.En viktig slutsats från projektet är att tvåledsramar används mycket mer sällan än fackverk/balk/pelar-system som stomsystem i lätta hallbyggnader i Sverige på grund av att kostnaderna blir mycket högre med tvåledsramar och att det är ett mer komplicerat system i beräkningsarbetet. De viktigaste slutsatserna från jämförelsestudien går att sammafatta som följande: Tvåledsramar är dyrare att använda. Tvåledsramar är ett mer komplicerat system beräkningsmässigt. Traditionen av att använda tvåledsramar finns inte och därför används inte systemet.

Attraktiv expatriering : Före, under och efter

Syfte och utgångspunkt:    Att utifrån fyra organisationer undersöka faktorer som är viktiga för arbete med expatriering och att använda Mendenhall, Dunbar och Oddous modell som inspiration för att skapa en egen modell med faktorer värdefulla för en expatrieringsprocess.   Forskningsresan:                 Utifrån referensram samt ett empiriskt resultat av intervjuer identifieras fyra kategorier, betydelse av att ta med familjen, mentorskap och stöd, anpassning till kultur och karriärplanering. Det empiriska resultatet samt referensramen är sedan grunden till analys och slutsats.   Slutsats:                              I slutsatsen presenteras betydelsefulla faktorer för utgången av studiens syfte.   Dessa faktorer används sedan i den modell författarna skapat. Modellen visar hur behovet av de fyra kategorierna är beroende av den planerade utlandsstationeringens längd.   Metod:                                Författarna av studien utgår från en kvalitativ ansats med djupintervjuer som metod. Det empiriska resultatet baseras på det material som framkommit genom djupintervjuer med  respondenterna från de fyra organisationerna.

Experimental and computational investigation of the roll forming process

One of the first questions to consider when designing a new roll forming line is the number of forming steps required to produce a profile. The number depends on material properties, the cross-section geometry and tolerance requirements, but the tool designer also wants to minimize the number of forming steps in order to reduce the investment costs for the customer. There are several computer aided engineering systems on the market that can assist the tool designing process. These include more or less simple formulas to predict deformation during forming as well as the number of forming steps. In recent years it has also become possible to use finite element analysis for the design of roll forming processes. The objective of the work presented in this thesis was to answer the following question: How should the roll forming process be designed for complex geometries and/or high strength steels? The work approach included both literature studies as well as experimental and modelling work. The experimental part gave direct insight into the process and was also used to develop and validate models of the process. Starting with simple geometries and standard steels the work progressed to more complex profiles of variable depth and width, made of high strength steels. The results obtained are published in seven papers appended to this thesis. In the first study (see paper 1) a finite element model for investigating the roll forming of a U-profile was built. It was used to investigate the effect on longitudinal peak membrane strain and deformation length when yield strength increases, see paper 2 and 3. The simulations showed that the peak strain decreases whereas the deformation length increases when the yield strength increases. The studies described in paper 4 and 5 measured roll load, roll torque, springback and strain history during the U-profile forming process. The measurement results were used to validate the finite element model in paper 1. The results presented in paper 6 shows that the formability of stainless steel (e.g. AISI 301), that in the cold rolled condition has a large martensite fraction, can be substantially increased by heating the bending zone. The heated area will then become austenitic and ductile before the roll forming. Thanks to the phenomenon of strain induced martensite formation, the steel will regain the martensite content and its strength during the subsequent plastic straining. Finally, a new tooling concept for profiles with variable cross-sections is presented in paper 7. The overall conclusions of the present work are that today, it is possible to successfully develop profiles of complex geometries (3D roll forming) in high strength steels and that finite element simulation can be a useful tool in the design of the roll forming process.

Evaluation of a PVT Air Collector

Hybrid Photovoltaic Thermal (PVT) collectors are an emerging technology that combines PV and solar thermal systems in a single solar collector producing heat and electricity simultaneously. The focus of this thesis work is to evaluate the performance of unglazed open loop PVT air system integrated on a garage roof in Borlänge. As it is thought to have a significant potential for preheating ventilation of the building and improving the PV modules electrical efficiency. The performance evaluation is important to optimize the cooling strategy of the collector in order to enhance its electrical efficiency and maximize the production of thermal energy. The evaluation process involves monitoring the electrical and thermal energies for a certain period of time and investigating the cooling effect on the performance through controlling the air mass flow provided by a variable speed fan connected to the collector by an air distribution duct. The distribution duct transfers the heated outlet air from the collector to inside the building. The PVT air collector consists of 34 Solibro CIGS type PV modules (115 Wp for each module) which are roof integrated and have replaced the traditional roof material. The collector is oriented toward the south-west with a tilt of 29 ᵒ. The collector consists of 17 parallel air ducts formed between the PV modules and the insulated roof surface. Each air duct has a depth of 0.05 m, length of 2.38 m and width of 2.38 m. The air ducts are connected to each other through holes. The monitoring system is based on using T-type thermocouples to measure the relevant temperatures, air sensor to measure the air mass flow. These parameters are needed to calculate the thermal energy. The monitoring system contains also voltage dividers to measure the PV modules voltage and shunt resistance to measure the PV current, and AC energy meters which are needed to calculate the produced electrical energy. All signals recorded from the thermocouples, voltage dividers and shunt resistances are connected to data loggers. The strategy of cooling in this work was based on switching the fan on, only when the difference between the air duct temperature (under the middle of top of PV column) and the room temperature becomes higher than 5 °C. This strategy was effective in term of avoiding high electrical consumption by the fan, and it is recommended for further development. The temperature difference of 5 °C is the minimum value to compensate the heat losses in the collecting duct and distribution duct. The PVT air collector has an area of (Ac=32 m2), and air mass flow of 0.002 kg/s m2. The nominal output power of the collector is 4 kWppv (34 CIGS modules with 115 Wppvfor each module). The collector produces thermal output energy of 6.88 kWth/day (0.21 kWth/m2 day) and an electrical output energy of 13.46 kWhel/day (0.42 kWhel/m2 day) with cooling case. The PVT air collector has a daily thermal energy yield of 1.72 kWhth/kWppv, and a daily PV electrical energy yield of 3.36 kWhel /kWppv. The fan energy requirement in this case was 0.18 kWh/day which is very small compared to the electrical energy generated by the PV collector. The obtained thermal efficiency was 8 % which is small compared to the results reported in literature for PVT air collectors. The small thermal efficiency was due to small operating air mass flow. Therefore, the study suggests increasing the air mass flow by a factor of 25. The electrical efficiency was fluctuating around 14 %, which is higher than the theoretical efficiency of the PV modules, and this discrepancy was due to the poor method of recording the solar irradiance in the location. Due to shading effect, it was better to use more than one pyranometer.

A Story of English Language Learning – How Can Children’s Literature be Used in Teaching Vocabulary to Young English Language Learners? : - A Literature Review

This study aims to find research relating to the use of children’s literature to promote vocabulary development in young children, particularly English language learners in Sweden. The main questions address how (methods) children’s literature can be used and why (reasons) children’s literature is often recommended for the teaching of vocabulary to young learners. The study also aims to explore reasons against the use of children’s literature in vocabulary teaching found in previous research. A systematic literature review was carried out, including results from five empirical studies. The studies involved native speakers, second language learners and foreign language learners from various backgrounds. The results suggest that while research has shown children’s literature to be a good tool to use with young learners, careful lesson planning needs to be carried out. Direct instruction and scaffolding using pictures, technology and gestures is recommended. Hence, the teacher plays an important part for the vocabulary development using children’s literature in the classroom.

MLCMS actual use, perceived use, and experiences of use

Mobile learning involves use of mobile devices to participate in learning activities. Most elearning activities are available to participants through learning systems such as learning content management systems (LCMS). Due to certain challenges, LCMS are not equally accessible on all mobile devices. This study investigates actual use, perceived usefulness and user experiences of LCMS use on mobile phones at Makerere University in Uganda. The study identifies challenges pertaining to use and discusses how to improve LCMS use on mobile phones. Such solutions are a cornerstone in enabling and improving mobile learning. Data was collected by means of focus group discussions, an online survey designed based on the Technology Acceptance Model (TAM), and LCMS log files of user activities. Data was collected from two courses where Moodle was used as a learning platform. The results indicate positive attitudes towards use of LCMS on phones but also huge challenges whichare content related and technical in nature.

One rapidly growing market of Sweden: organic food : A qualitative study portraying some consumers’ decision to purchase organic food

In recent years there has been a significantly rising trend amongst consumers for health and environmental issues, which has resulted in greater attention for and sales of organic food. Organic food production strives to use natural resources, such as land, energy and water in a sustainable way and the products does not contain artificial fertilizers or chemical pesticides. However, organic food products are also often more expensive and less available in comparison to conventional food products. Despite this, interest for and sales of organic food products have increased around the globe, and in Sweden particularly, the increase in sales has grown largely from an international perspective. This thesis is of qualitative character and is focused on studying some consumers from the Swedish market of organic food. The purpose of this thesis is to contribute with a better understanding on the buying decision process regarding organic food purchase. To achieve this, the authors have studied some consumers that purchase organic food and have searched for patterns that could be identified in the decision process. The consumer buying decision process model has been used for portrayal of the chosen consumers’ decision to purchase organic food products. Interviews with six Swedish consumers were conducted, whereas each respondent continuously purchase organic food products. Results show that the purchase of organic food products begins with discovering an unsatisfied need state, which the consumers of this study desired to change with the purchase of organic food products. This study show how six consumers reason when passing through the stages of the buying decision process, in order to satisfy their desired need state. The authors found that the respondents feel satisfied with purchasing organic food products, which lead them in to continuously buying these products. Altogether, the findings contribute with knowledge that can come to be helpful when wanting to understand more about the consumer decision to purchase organic food.

Factors that Motivate Pupils in Grades 4-6 in Sweden to Speak English as a Foreign Language

This is an empirical study about factors that motivate pupils to speak English as a foreign language. The aim of this study is to investigate when pupils in the classroom situation, in Grades 4-6 in a school in Sweden, are motivated to speak English as a foreign language, and why they are motivated to speak English in these situations. To implement this study, questionnaires and interviews have been chosen as methods. 51 pupils in Grades 4-6 took part of the study. Since being able to communicate orally in a foreign language is of great advantage for one, and creates opportunities both for work and for study abroad, it is important for pupils to learn how to communicate orally in English. It is important to be able to use the language. In the English curriculum in Swedish schools, speaking English is a skill pupils must possess. Since this is the requirement it is important that teachers in Sweden relate to this. Many pupils do not like to speak in front of the rest of the class and some pupils only like to speak in informal situations. Therefore, teachers must use various strategies to create a willingness to communicate among pupils and various strategies to motivate them to speak English. The results show that pupils are motivated to use the language in class when they have recently been abroad. It also shows that they are motivated when they can decide the topic and speak about something they are interested in.

Learning by Reading : A literature study on the use of authentic texts in the EFL upper elementary classroom

The English language is widely used throughout the world and has become a core subject in many countries, especially for students in the upper elementary classroom. While textbooks have been the preferred EFL teaching method for a long time, this belief has seemingly changed within the last few years. Therefore, this study looks at what prior research says about the use of authentic texts in the EFL upper elementary classroom with an aim to answer research questions on how teachers can work with authentic texts, what the potential benefits of using authentic texts are and what teachers and students say about the use of authentic texts in the EFL classroom. While this thesis is written from a Swedish perspective, it is recognized that many countries teach EFL. Therefore, international results have also been taken into consideration and seven previous research studies have been analyzed in order to gain a better understanding of the use of authentic texts in the EFL classroom. Results indicate that the use of authentic texts is beneficial in teaching EFL. However, many teachers are still reluctant to use these, mainly because of time constraints and the belief that such texts are too difficult for their students. Since these findings are mainly focused on areas outside of Sweden, additional research is needed before conclusions can be drawn on the use of authentic texts in the Swedish upper elementary EFL classroom.

English as the target language : A literature study on teachers’ and L2 learners’ language use in the upper elementary classroom

Even though English is a subject where Swedish pupils do well compared to pupils in other countries, research indicates that pupils are not always motivated to learn in the English classroom. Therefore, the aim of this study is to find research relating to the use of the target language in classrooms for pupils at the upper elementary level, particularly language learners in Sweden. The focus of this thesis is to find out what benefits and challenges accompany the use of the target language during English lessons, as well as what pupils’ opinions are on the consistent use of the target language in the classroom. This literature review of five research articles shows that it is beneficial for pupils’ language development to have lessons where mainly the target language is used. It is for example beneficial for pupils’ ability to speak, their pronunciation, vocabulary and ability to use language strategies. The results show that there are challenges as well, especially for the teachers, since use of the target language presumes that the teacher has good language skills and is capable of scaffolding each pupil at their individual level and in their zone of proximal development. Furthermore, there are challenges like differences in pupils’ skill level, creating tasks that both motivate and stimulate, and creating a safe learning environment. Even though the results in this thesis are limited, it is still obvious that it is an important area, where more research is necessary in order to assist teachers in how to teach English as effectively as possible.

The "reflection protocol" - a way to develop learning and independent thinking?

It is now-a-days more and more common in the academic world to use new forms of “learning-tools”. One of those is the “reflection protocol”, which usually consist of a few pages of freely written text, related to something the students have read. There seems to be a lot of different opinions about the value to use this method. Some teachers and students are enthusiastic and others are rather critical. To write a “reflection protocol” is not in the first place to do a summery, a review, not even to analyze a text. Instead it is about to write down thoughts and questions that comes up as a result of the reading. It is also about doing associations, reflections and to interpret a text and relate this to a theme of some kind. The purpose to use “reflection protocols” is, as we see it, mainly for the student to practice independent thinking from a scientific point of view, but it also gives a possibility to a better understanding of another person’s thinking. This seems to open up for a fruitful dialogue and a way to learn. We will in this paper discuss if that could be the case.

English as a Second Language and Children’s literature : An empirical study on Swedish elementary school teachers’ methods and attitudes towards the use of children’s literature in the English classroom

Previous research has shown multiple benefits and challenges with the incorporation of children’s literature in the English as a Second language (ESL) classroom. In addition, the use of children’s literature in the lower elementary English classroom is recommended by the Swedish National Agency for Education. Consequently, the current study explores how teachers in Swedish elementary school teach ESL through children’s literature. This empirical study involves English teachers from seven schools in a small municipality in Sweden. The data has been collected through an Internet survey. The study also connects the results to previous international research, comparing Swedish and international research. The results suggest that even though there are many benefits of using children’s literature in the ESL classroom, the respondents seldom use these authentic texts, due to limited time and a narrow supply of literature, among other factors. However, despite these challenges, all of the teachers claim to use children’s literature by reading aloud in the classroom. Based on the results, further research exploring pupils’ thoughts in contrast to teachers would be beneficial. In addition, the majority of the participants expressed that they wanted more information on how to use children’s literature. Therefore, additional research relating to beneficial methods of teaching English through children’s literature, especially in Sweden, is recommended.

Utveckling av metod för att bedöma behovet av ogräsbekämpning i spår

A system for weed management on railway embankments that is both adapted to the environment and efficient in terms of resources requires knowledge and understanding about the growing conditions of vegetation so that methods to control its growth can be adapted accordingly. Automated records could complement present-day manual inspections and over time come to replace these. One challenge is to devise a method that will result in a reasonable breakdown of gathered information that can be managed rationally by affected parties and, at the same time, serve as a basis for decisions with sufficient precision. The project examined two automated methods that may be useful for the Swedish Transport Administration in the future: 1) A machine vision method, which makes use of camera sensors as a way of sensing the environment in the visible and near infrared spectrum; and 2) An N-Sensor method, which transmits light within an area that is reflected by the chlorophyll in the plants. The amount of chlorophyll provides a value that can be correlated with the biomass. The choice of technique depends on how the information is to be used. If the purpose is to form a general picture of the growth of vegetation on railway embankments as a way to plan for maintenance measures, then the N-Sensor technique may be the right choice. If the plan is to form a general picture as well as monitor and survey current and exact vegetation status on the surface over time as a way to fight specific vegetation with the correct means, then the machine vision method is the better of the two. Both techniques involve registering data using GPS positioning. In the future, it will be possible to store this information in databases that are directly accessible to stakeholders online during or in conjunction with measures to deal with the vegetation. The two techniques were compared with manual (visual) estimations as to the levels of vegetation growth. The observers (raters) visual estimation of weed coverage (%) differed statistically from person to person. In terms of estimating the frequency (number) of woody plants (trees and bushes) in the test areas, the observers were generally in agreement. The same person is often consistent in his or her estimation: it is the comparison with the estimations of others that can lead to misleading results. The system for using the information about vegetation growth requires development. The threshold for the amount of weeds that can be tolerated in different track types is an important component in such a system. The classification system must be capable of dealing with the demands placed on it so as to ensure the quality of the track and other pre-conditions such as traffic levels, conditions pertaining to track location, and the characteristics of the vegetation. The project recommends that the Swedish Transport Administration: Discusses how threshold values for the growth of vegetation on railway embankments can be determined Carries out registration of the growth of vegetation over longer and a larger number of railway sections using one or more of the methods studied in the project Introduces a system that effectively matches the information about vegetation to its position Includes information about the growth of vegetation in the records that are currently maintained of the track’s technical quality, and link the data material to other maintenance-related databases Establishes a number of representative surfaces in which weed inventories (by measuring) are regularly conducted, as a means of developing an overview of the long-term development that can serve as a basis for more precise prognoses in terms of vegetation growth Ensures that necessary opportunities for education are put in place