Structural characterization of Li-MN doped powders prepared by Pechini's method

Pechini's method has been successfully used to prepare Li-doped MgNb2O6(MN) at short time and low temperature. It consists in the preparation of metal citrate solution, which is polymerized at 250°C to form a high viscous resin. This resin was burned in a box type furnace at 400°C/2h and ground in a mortar. Successive steps of calcination up to 900°C were used to form a crystalline precursor. SEM, DTA and XRD were used to characterize the powders. MN precursor powders containing from 0.1 to 5.0 mol% of LiNbO3 additive was prepared aiming better dielectric properties and microstructural characteristics of the PMN prepared from columbite route. SEM analysis showed that particles increased by sintering, forming large agglomerates. The surface area is also substantially reduced with the increase in additive amount above 1.0 mol%. In XRD pattern of the precursor material with 5.0 mol% of additive was observed the LiNbO3 phase of trigonal structure. XRD data were used for Rietveld refinement and a decrease in microstrain and pronounced increase in crystallite size with the increase of LiNbO3 were observed. It is in agreement with the particle morphologies observed by SEM analysis.

Desenvolvimento e caracterização de dispositivos eletroluminescentes contendo uma blenda polimérica condutora e Zn2SiO4:Mn

Despite the great development of organic and polymeric electroluminescent materials, the large scale commercial application of devices made with these materials seems conditioned to specific cases, mainly due to the high cost and the low durability, in compared to conventional technologies. In this study was produced electroluminescent devices by a process simple, drop casting. Were produced electroluminescent films containing Zn2SiO4:Mn immersed in a conductive polymer blend with different thicknesses. The morphological characteristics of these films were studied by scanning electronic microscopy. These films were used in the manufacture of electroluminescent devices, in which the light emission properties of the developed material were evaluated. The blend was composed of the conductive polymer Poly(o-methoxyaniline), doped with p-toluene sulfonic acid, and an insulating polymer, Poly(vinylidene fluoride) and its copolymer Poly(vinylidene fluoride-cotrifluoroethylene). To this blend was added Zn2SiO4:Mn, thereby forming the composite. A first set of devices was obtained using composites with different weight fraction of polymeric and inorganic phases, which were deposited by drop casting over ITO substrates. Upper electrodes of aluminum were deposited by thermal evaporation. The resulting device architecture was a sandwich type structure ITO/ composite/ Al. A second set of devices was obtained as self-sustaining films using the best composite composition obtained for the device of the first set. ITO electrodes were deposited by RF-Sputtering, in both faces of these films. The AC electrical characterization of the devices was made with impedance spectroscopy measurements, and the DC electrical characterization was performed using a source/ meter unit Keithley 2410. The devices light emission was measured using a photodiode coupled to a digital electrometer, Keithley 6517A. The devices electrooptical characterization showed that the...

Modeling the crystallographic structure of Ho(Ni,Co,Mn)O3±δ perovskite-type manganite

Crystallographic and microstructural properties of Ho(Ni,Co,Mn)O3± perovskite-type multiferroic material are reported. Samples were synthesized with a modified polymeric precursor method. The synchrotron X-ray powder diffraction (SXRPD) technique associated to Rietveld refinement method was used to perform structural characterization. The crystallographic structures, as well as microstructural properties, were studied to determine unit cell parameters and volume, angles and atomic positions, crystallite size and strain. X-ray energies below the absorption edges of the transition metals helped to determine the mean preferred atomic occupancy for the substituent atoms. Furthermore, analyzing the degree of distortion of the polyhedra centered at the transitions metal atoms led to understanding the structural model of the synthesized phase. X-ray photoelectron spectroscopy (XPS) was performed to evaluate the valence states of the elements, and the tolerance factor and oxygen content. The obtained results indicated a small decrease distortion in structure, close to the HoMnO3 basis compound. In addition, the substituent atoms showed the same distribution and, on average, preferentially occupied the center of the unit cell.

Paper-based diffusive gradients in thin films technique coupled to energy dispersive X-ray fluorescence spectrometry for the determination of labile Mn, Co, Ni, Cu, Zn and Pb in river water

The diffusive gradients in thin films (DGT) technique has shown enormous potential for labile metal monitoring in fresh water due to the preconcentration, time-integrated, matrix interference removal and speciation analytical features. In this work, the coupling of energy dispersive X-ray fluorescence (EDXRF) with paper-based DGT devices was evaluated for the direct determination of Mn, Co. Ni, Cu, Zn and Pb in fresh water. The DGT samplers were assembled with cellulose (Whatman 3 MM chromatography paper) as the diffusion layer and a cellulose phosphate ion exchange membrane (Whatman P 81 paper) as the binding agent. The diffusion coefficients of the analytes on 3 MM chromatography paper were calculated by deploying the DGT samplers in synthetic solutions containing 500 mu g L-1 of Mn. Co, Ni, Cu, Zn and Pb (4 L at pH 5.5 and ionic strength at 0.05 mol L-1). After retrieval, the DGT units were disassembled and the P81 papers were dried and analysed by EDXRF directly. The 3 MM chromatographic paper diffusion coefficients of the analytes ranged from 1.67 to 1.87 x 10(-6) cm(2) s(-1). The metal retention and phosphate group homogeneities on the P81 membrane was studied by a spot analysis with a diameter of 1 mm. The proposed approach (DGT-EDXRF coupling) was applied to determine the analytes at five sampling sites (48 h in situ deployment) on the Piracicaba river basin, and the results (labile fraction) were compared with 0.45 mu m dissolved fractions determined by synchrotron radiation-excited total reflection X-ray fluorescence (SR-TXRF). The limits of detection of DGT-EDXRF coupling for the analytes (from 7.5 to 26 mu g L-1) were similar to those obtained by the sensitive SR-TXRF technique (3.8 to 9.1 mu g L-1). (C) 2012 Elsevier B.V. All rights reserved.

Tuning Low-Spin to High-Spin Mn Pairs in 2-D ZnO by Injecting Holes

We have performed an ab initio theoretical investigation of substitutional Mn(Zn) atoms in planar structures of ZnO, viz., monolayer [(ZnO)(1)] and bilayer [(ZnO)(2)] systems. Due to the 2-D quantum confinement effects, in those Mn -doped (ZnO)(1) and (ZnO)(2) structures, the antiferromagnetic (AFM) coupling between (nearest neighbor) Mn(Zn) impurities have been strengthened when compared with the one in ZnO bulk systems. On the other hand, we find that the magnetic state of these systems can be tuned from AFM to FM by adding holes, which can be supplied by a p-type doping or even photoionization processes. Whereas, upon addition of electrons (n-type doping), the system keeps its AFM configuration.

First-principles studies of complex magnetism in Mn nanostructures on the Fe(001) surface

The magnetic properties of Mn nanostructures on the Fe(001) surface have been studied using the noncollinear first-principles real space-linear muffin-tin orbital-atomic sphere approximation method within density-functional theory. We have considered a variety of nanostructures such as adsorbed wires, pyramids, and flat and intermixed clusters of sizes varying from two to nine atoms. Our calculations of interatomic exchange interactions reveal the long-range nature of exchange interactions between Mn-Mn and Mn-Fe atoms. We have found that the strong dependence of these interactions on the local environment, the magnetic frustration, and the effect of spin-orbit coupling lead to the possibility of realizing complex noncollinear magnetic structures such as helical spin spiral and half-skyrmion.

Subdivision of Hysteresis Loss in Mn-Zn Ferrite Toroidal Cores

The hysteresis loss subdivision method proved to be a strong tool to help in the analysis of different energy dissipation mechanisms along the quasi-static hysteresis loop measured on electrical steels. This paper used the samemethod to discuss the mechanisms involving the energy loss dissipation in Mn-Zn ferrite toroidal cores. The samples, sintered under controlled atmosphere in industrial conditions, were measured under triangular waveform excitation at very low frequency (5 mHz) and peak flux densities varying from 0.05 T to 0.45 T. The results show a different behavior between the low inductions hysteresis loss (WLI) and the high induction hysteresis loss (WHI) which proves the existence of different energy dissipation mechanisms affecting these loss components.

Evaluation of Inductively Coupled Plasma Mass Spectrometry for Determining Ca, Cu, Fe, Mg, Mn, Se and Zn in Bovine Semen Samples using a Simple Sample Dilution Method

A simple and fast method for the determination of Ca, Cu, Fe, Mg, Mn, Se and Zn in bovine semen by quadrupole inductively coupled plasma spectrometry (q-ICP-MS) is described. Prior to analysis, samples (200 mu L) were diluted 1:50 in a solution containing 0.01% v/v Triton (R) X-100 and 0.5% v/v nitric acid and directly analyzed by ICP-MS. The limits of detection of the method are 0.3, 0.03, 0.2, 0.04, 0.04, 0.03 and 0.03 mu g L-1 for Ca-44, Cu-63, Fe-57, Mg-24, Zn-64, Se-82 and Mn-55, respectively. For purposes of comparison and method validation, four ordinary bovine semen samples were directly analyzed by ICP-MS and by flame atomic absorption spectrometry (FAAS) or graphite furnace atomic absorption spectrometry (GF AAS), with no statistical difference between the techniques at the 95% level when applying the t-test. Then, the proposed method was applied in the determinations of Ca, Cu, Fe, Mg, Mn, Se and Zn in collected samples of bovine semen from different breeds, which are used in reproduction programs and artificial insemination.

GaMnAs: Position of Mn-d levels and majority spin band gap predicted from GGA-1/2 calculations

Among all magnetic semiconductors, GaMnAs seems to be the most important one. In this work, we present accurate first-principles calculations of GaMnAs within the GGA-1/2 approach: We concentrate our efforts in obtaining the position of the peak of Mn-d levels in the valence band and also the majority spin band gap. For the position of the Mn-d peak, we find a value of 3.3 eV below the Fermi level, in good agreement with the most recent experimental results of 3.5 and 3.7 eV. An analytical expression that fits the calculated E-g(x) for majority spin is derived in order to provide ready access to the band gap for the composition range from 0 to 0.25. We found a value of 3.9 eV for the gap bowing parameter. The results agree well with the most recent experimental data. (C) 2012 American Institute of Physics. [http://dx.doi.org/10.1063/1.4718602]

Evaluation of inductively coupled plasma mass spectrometry for determining Ca, Cu, Fe, Mg, Mn, Se and Zn in bovine semen samples using a simple sample dilution method

A simple and fast method for the determination of Ca, Cu, Fe, Mg, Mn, Se and Zn in bovine semen by quadrupole inductively coupled plasma spectrometry (q-ICP-MS) is described. Prior to analysis, samples (200 µL) were diluted 1:50 in a solution containing 0.01% v/v Triton® X-100 and 0.5% v/v nitric acid and directly analyzed by ICP-MS. The limits of detection of the method are 0.3, 0.03, 0.2, 0.04, 0.04, 0.03 and 0.03 µg L-1 for 44Ca, 63Cu, 57Fe, 24Mg, 64Zn, 82Se and 55Mn, respectively. For purposes of comparison and method validation, four ordinary bovine semen samples were directly analyzed by ICP-MS and by flame atomic absorption spectrometry (FAAS) or graphite furnace atomic absorption spectrometry (GF AAS), with no statistical difference between the techniques at the 95% level when applying the t-test. Then, the proposed method was applied in the determinations of Ca, Cu, Fe, Mg, Mn, Se and Zn in collected samples of bovine semen from different breeds, which are used in reproduction programs and artificial insemination.

"Är det någon som slåss är det män, men jag tycker inte att man blir mer man för att man gör det." : En studie om synen på män, manlighet och våld

När det gäller utövandet av våld är gruppen män kraftigt överrepresenterade. Mäns utövande av våld är ett samhällsproblem som i allra högsta grad är relevant för socialt arbete. Uppsatsens syfte var att få en ökad kunskap om relationen mellan manlighet och våld samt mäns tankar om manlighet och våld. Förutom en genomgång av tidigare forskning genomfördes kvalitativa intervjuer med fem män om deras tankar kring manlighet och våld. Ett strategiskt urval användes i syfte att få fram informanter som uppvisade stor variationsbredd. Studiens resultat pekade på att det finns många olika sätt att se på och att göra manlighet. Ett rimligt antagande är även att synen på manlighet har betydelse för mäns utövande av våld på så sätt att en syn på manlighet som präglas av styrka, dominans och kontroll kan främja mäns utövande av våld. Det finns även forskning som tyder på att våld i vissa situationer kan användas av mäns som en resurs att göra manlighet. När det gäller relationen mellan manlighet och våld ansåg informanterna att det inte var manligt att utöva våld men kopplar samtidigt ihop manlighet med fysiskt styrka och kroppslig prestation samt utövandet av legitimt våld, exempelvis inom idrott. Avslutningsvis diskuteras betydelsen och konsekvenserna av hur vi inom socialt arbete ser på manlighet och våld.

Unga män berättar om våld

Denna uppsats syftar till att undersöka och belysa vad som motiverar vissa killar till att tillämpa våld som problemlösning i deras vardag utifrån dessa killars egna förståelse för sina våldshandlingar. För att ge en ökad förståelse för detta har en narrativ intervjumetod använts med livsberättelser som utgångspunkt. För att belysa detta ämne har vi använt oss av maktlöshetsteorin där bemästring av vanmakt ingår. Våra resultat visar på att dessa unga män sökte att genom våldshandlingar bemästra sin vardag genom att skaffa sig position inom gänget och ett rykte om att vara farlig. Att föreställningen om ”respekt” handlade om att ingjuta rädsla hos andra och hur detta tillsammans med bemästring blev en motivator för våldet. Strävan efter kickupplevelser genom våld var också en viktig motivator för våld. Deras sociala nätverk som i huvudsakligen bestod av kamratgänget hade en stor betydelse för anammandet av våldsamma attityder och föreställningar samt för utvecklandet av en överdriven mansroll vilken bidrog till våld. Bruket av alkohol var en del av socialiseringsprocessen i kamratgänget och alkoholintag var vanligt förekommande i samband med våldshandlingar. Problematiska familjeförhållanden bidrog till upplevelse av vanmakt vilken bemästrades med våld. Förslag på vidare forskning är att undersöka vilka mekanismer som ligger bakom till att killar söker bekräftelse och självförverkligande på destruktivasätt.

Untersuchung magnetischer Nanostrukturen mittels Rastertunnelspektroskopie und Kerr-Magnetometrie am Beispiel von Fe, Co, Co-Fe und Fe-Mn Nanostrukturen

Nach einer kurzen Einführung in die Entwicklung der magnetischen Anwendungen, werden in Kapitel 2 und 3 die physikalischen Grundlagen der Messmethoden, insbesondere die Rastertunnelspektroskopie und Kerr-Magnetometrie, sowie der experimentelle Aufbau erläutert. Kapitel 4 beschäftigt sich mit den magnetischen Eigenschaften von quasi ein-dimensionalen ferromagnetischen Nanostreifen und Monolagen, die durch Selbstorganisation auf einem Wolfram(110)-Einkristall mit vizinaler und glatter Oberfläche präpariert werden. Hierbei wird die Temperaturabhängigkeit der magnetischen Größen, wie Remanenz, Sättigungsmagnetisierung und Suszeptibilität, sowie die Auswirkung einer Abdeckung des Systems auf die Domänenwandenergie und Anisotropie untersucht. Zusätzlich wird die Kopplung von parallelen Nanostreifen in Abhängigkeit des Streifenabstandes betrachtet. In Kapitel 5 werden das Wachstum und die Morphologie von Co-Monolagen auf W(110) untersucht. Der Übergang von pseudomorphem zu dicht gepacktem Wachstum in der Monolage wird mit Hilfe der Rastertunnelspektroskopie sichtbar gemacht, ebenso wie unterschiedliche Stapelfolgen in Tripellagen Co-Systemen. Atomar aufgelöste Rastertunnelmikroskopie erlaubt die genauen Atompositionen der Oberfläche zu bestimmen und mit theoretischen Wachstumsmodellen zu vergleichen. Auf die Untersuchung zwei-dimensionaler binärer Co-Fe und Fe-Mn Legierungen auf W(110) wird in Kapitel 6 eingegangen. Mit einer Präparationstemperatur von T=520 K ist es möglich, atomar geordnete Co-Fe Legierungsmonolagen wachsen zu lassen. Ein direkter Zusammenhang zwischen der Magnetisierung und der lokalen Zustandsdichte in Abhängigkeit der Legierungszusammensetzung wird gezeigt.