Influence of ventilation and filtration on indoor particle concentrations in urban office buildings

This study aimed to quantify the efficiency of deep bag and electrostatic filters, and assess the influence of ventilation systems using these filters on indoor fine (<2.5 µm) and ultrafine particle concentrations in commercial office buildings. Measurements and modelling were conducted for different indoor and outdoor particle source scenarios at three office buildings in Brisbane, Australia. Overall, the in-situ efficiency, measured for particles in size ranges 6 to 3000 nm, of the deep bag filters ranged from 26.3 to 46.9% for the three buildings, while the in-situ efficiency of the electrostatic filter in one building was 60.2%. The highest PN and PM2.5 concentrations in one of the office buildings (up to 131% and 31% higher than the other two buildings, respectively) were due to the proximity of the building’s HVAC air intakes to a nearby bus-only roadway, as well as its higher outdoor ventilation rate. The lowest PN and PM2.5 concentrations (up to 57% and 24% lower than the other two buildings, respectively) were measured in a building that utilised both outdoor and mixing air filters in its HVAC system. Indoor PN concentrations were strongly influenced by outdoor levels and were significantly higher during rush-hours (up to 41%) and nucleation events (up to 57%), compared to working-hours, for all three buildings. This is the first time that the influence of new particle formation on indoor particle concentrations has been identified and quantified. A dynamic model for indoor PN concentration, which performed adequately in this study also revealed that using mixing/outdoor air filters can significantly reduce indoor particle concentration in buildings where indoor air was strongly influenced by outdoor particle levels. This work provides a scientific basis for the selection and location of appropriate filters and outdoor air intakes, during the design of new, or upgrade of existing, building HVAC systems. The results also serve to provide a better understanding of indoor particle dynamics and behaviours under different ventilation and particle source scenarios, and highlight effective methods to reduce exposure to particles in commercial office buildings.

Comparing and complementing methods : traditional market research vs. deep customer insights

Quantitative market data has traditionally been used throughout marketing and business as a tool to inform and direct design decisions. However, in our changing economic climate, businesses need to innovate and create products their customers will love. Deep customer insight methods move beyond just questioning customers and aims to provoke true emotional responses in order to reveal new opportunities that go beyond functional product requirements. This paper explores traditional market research methods and compares them to methods used to gain deep customer insights. This study reports on a collaborative research project with seven small to medium enterprises and four multi-national organisations. Firms were introduced to a design led innovation approach, and were taught the different methods to gain deep customer insights. Interviews were conducted to understand the experience and outcomes of pre-existing research methods and deep customer insight approaches. Findings concluded that deep customer insights were unlikely to be revealed through traditional market research techniques. The theoretical outcome of this study is a complementary methods matrix, providing guidance on appropriate research methods in accordance to a project’s timeline.

Energy efficient virtual machine placement in data centers

Electricity cost has become a major expense for running data centers and server consolidation using virtualization technology has been used as an important technology to improve the energy efficiency of data centers. In this research, a genetic algorithm and a simulation-annealing algorithm are proposed for the static virtual machine placement problem that considers the energy consumption in both the servers and the communication network, and a trading algorithm is proposed for dynamic virtual machine placement. Experimental results have shown that the proposed methods are more energy efficient than existing solutions.

Nurse-administered procedural sedation and analgesia in the cardiac catheterisation laboratory : a mixed methods study

The cardiac catheterisation laboratory (CCL) is a specialised medical radiology facility where both chronic-stable and life-threatening cardiovascular illness is evaluated and treated. Although there are many potential sources of discomfort and distress associated with procedures performed in the CCL, a general anaesthetic is not usually required. For this reason, an anaesthetist is not routinely assigned to the CCL. Instead, to manage pain, discomfort and anxiety during the procedure, nurses administer a combination of sedative and analgesic medications according to direction from the cardiologist performing the procedure. This practice is referred to as nurse-administered procedural sedation and analgesia (PSA). While anecdotal evidence suggested that nurse-administered PSA was commonly used in the CCL, it was clear from the limited information available that current nurse-led PSA administration and monitoring practices varied and that there was contention around some aspects of practice including the type of medications that were suitable to be used and the depth of sedation that could be safely induced without an anaesthetist present. The overall aim of the program of research presented in this thesis was to establish an evidence base for nurse-led sedation practices in the CCL context. A sequential mixed methods design was used over three phases. The objective of the first phase was to appraise the existing evidence for nurse-administered PSA in the CCL. Two studies were conducted. The first study was an integrative review of empirical research studies and clinical practice guidelines focused on nurse-administered PSA in the CCL as well as in other similar procedural settings. This was the first review to systematically appraise the available evidence supporting the use of nurse-administered PSA in the CCL. A major finding was that, overall, nurse-administered PSA in the CCL was generally deemed to be safe. However, it was concluded from the analysis of the studies and the guidelines that were included in the review, that the management of sedation in the CCL was impacted by a variety of contextual factors including local hospital policy, workforce constraints and cardiologists’ preferences for the type of sedation used. The second study in the first phase was conducted to identify a sedation scale that could be used to monitor level of sedation during nurse-administered PSA in the CCL. It involved a structured literature review and psychometric analysis of scale properties. However, only one scale was found that was developed specifically for the CCL, which had not undergone psychometric testing. Several weaknesses were identified in its item structure. Other sedation scales that were identified were developed for the ICU. Although these scales have demonstrated validity and reliability in the ICU, weaknesses in their item structure precluded their use in the CCL. As findings indicated that no existing sedation scale should be applied to practice in the CCL, recommendations for the development and psychometric testing of a new sedation scale were developed. The objective of the second phase of the program of research was to explore current practice. Three studies were conducted in this phase using both quantitative and qualitative research methods. The first was a qualitative explorative study of nurses’ perceptions of the issues and challenges associated with nurse-administered PSA in the CCL. Major themes emerged from analysis of the qualitative data regarding the lack of access to anaesthetists, the limitations of sedative medications, the barriers to effective patient monitoring and the impact that the increasing complexity of procedures has on patients' sedation requirements. The second study in Phase Two was a cross-sectional survey of nurse-administered PSA practice in Australian and New Zealand CCLs. This was the first study to quantify the frequency that nurse-administered PSA was used in the CCL setting and to characterise associated nursing practices. It was found that nearly all CCLs utilise nurse-administered PSA (94%). Of note, by characterising nurse-administered PSA in Australian and New Zealand CCLs, several strategies to improve practice, such as setting up protocols for patient monitoring and establishing comprehensive PSA education for CCL nurses, were identified. The third study in Phase Two was a matched case-control study of risk factors for impaired respiratory function during nurse-administered PSA in the CCL setting. Patients with acute illness were found to be nearly twice as likely to experience impaired respiratory function during nurse-administered PSA (OR=1.78; 95%CI=1.19-2.67; p=0.005). These significant findings can now be used to inform prospective studies investigating the effectiveness of interventions for impaired respiratory function during nurse-administered PSA in the CCL. The objective of the third and final phase of the program of research was to develop recommendations for practice. To achieve this objective, a synthesis of findings from the previous phases of the program of research informed a modified Delphi study, which was conducted to develop a set of clinical practice guidelines for nurse-administered PSA in the CCL. The clinical practice guidelines that were developed set current best practice standards for pre-procedural patient assessment and risk screening practices as well as the intra and post-procedural patient monitoring practices that nurses who administer PSA in the CCL should undertake in order to deliver safe, evidence-based and consistent care to the many patients who undergo procedures in this setting. In summary, the mixed methods approach that was used clearly enabled the research objectives to be comprehensively addressed in an informed sequential manner, and, as a consequence, this thesis has generated a substantial amount of new knowledge to inform and support nurse-led sedation practice in the CCL context. However, a limitation of the research to note is that the comprehensive appraisal of the evidence conducted, combined with the guideline development process, highlighted that there were numerous deficiencies in the evidence base. As such, rather than being based on high-level evidence, many of the recommendations for practice were produced by consensus. For this reason, further research is required in order to ascertain which specific practices result in the most optimal patient and health service outcomes. Therefore, along with necessary guideline implementation and evaluation projects, post-doctoral research is planned to follow up on the research gaps identified, which are planned to form part of a continuing program of research in this field.

Novel channel tracking and equalization methods in MU-MIMO-OFDM systems

The methodology undertaken, the channel model and the system model created for developing a novel adaptive equalization method and a novel channel tracking method for uplink of MU-MIMO-OFDM systems is presented in this paper. The results show that the channel tracking method works with 97% accuracy, while the training-based initial channel estimation method shows poor performance in estimating the actual channel comparatively.

An analysis of the KEEP CLEAR pavement markings effects on queuing vehicles dynamic performance at urban signalised intersections

KEEP CLEAR pavement markings are widely used at urban signalised intersections to indicate to drivers to avoid entering blocked intersections. For example, ‘Box junctions’ are most widely used in the United Kingdom and other European countries. However, in Australia, KEEP CLEAR markings are mostly used to improve access from side roads onto a main road, especially when the side road is very close to a signalised intersection. This paper aims to reveal how the KEEP CLEAR markings affect the dynamic performance of the queuing vehicles on the main road, where the side road access is near a signalised intersection. Raw traffic field data was collected from an intersection at the Gold Coast, Australia, and the Kanade–Lucas–Tomasi (KLT) feature tracker approach was used to extract dynamic vehicle data from the raw video footage. The data analysis reveals that the KEEP CLEAR markings generate positive effects on the queuing vehicles in discharge on the main road. This finding refutes the traditional viewpoint that the KEEP CLEAR pavement markings will cause delay for the queuing vehicles’ departure due to the enlarged queue spacing. Further studies are suggested in this paper as well.

Social Media Sites as Online Information Grounds : An exploratory study of the ways in which Information Technology (IT) professionals experience social media

Social media tools are often the result of innovations in Information Technology and developed by IT professionals and innovators. Nevertheless, IT professionals, many of whom are responsible for designing and building social media technologies, have not been investigated on how they themselves use or experience social media for professional purposes. This study will use Information Grounds Theory (Pettigrew, 1998) as a framework to study IT professionals’ experience in using social media for professional purposes. Information grounds facilitates the opportunistic discovery of information within social settings created temporarily at a place where people gather for a specific purpose (e.g., doctors’ waiting rooms, office tea rooms etc.), but the social atmosphere stimulates spontaneous sharing of information (Pettigrew, 1999). This study proposes that social media has the qualities that make it a rich information grounds; people participate from separate “places” in cyberspace in a synchronous manner in real-time, making it almost as dynamic and unplanned as physical information grounds. There is limited research on how social media platforms are perceived as a “place,” (a place to go to, a place to gather, or a place to be seen in) that is comparable to physical spaces. There is also no empirical study on how IT professionals use or “experience” social media. The data for this study is being collected through a study of IT professionals who currently use Twitter. A digital ethnography approach is being taken wherein the researcher uses online observations and “follows” the participants online and observes their behaviours and interactions on social media. Next, a sub-set of participants will be interviewed on their experiences with and within social media and how social media compares with traditional methods of information grounds, information communication, and collaborative environments. An Evolved Grounded Theory (Glaser, 1992) approach will be used to analyse tweets data and interviews and to map the findings against the Information Ground Theory. Findings from this study will provide foundational understanding of IT professionals’ experiences within social media, and can help both professionals and researchers understand this fast-evolving method of communications.

Maintaining shared knowledge of acquaintance : methods people use to establish who knows whom

Acquaintance is a fundamental determinant of how people behave when interacting with one another. This article focuses on how this type of personal knowledge is an important consideration for people as social actors. Studying naturally-occurring social encounters, I describe how speakers use particular references to convey whether a recipient should be able to recognise a non-present third party. On some occasions, however, the presumption of recognisability or non-recognisability that underpins the use of a particular reference proves questionable. By exploring how recipients can challenge reference forms, and thereby reject claims of either recognisability or non-recognisability, I explain how people establish and maintain a shared understanding of who knows whom. I conclude by discussing motivations for this behaviour, and thereby contribute to understanding the commonsense reasoning that underpins orderly conduct in this aspect of social encounters.

Monitoring of complex systems of interacting dynamic systems

Increases in functionality, power and intelligence of modern engineered systems led to complex systems with a large number of interconnected dynamic subsystems. In such machines, faults in one subsystem can cascade and affect the behavior of numerous other subsystems. This complicates the traditional fault monitoring procedures because of the need to train models of the faults that the monitoring system needs to detect and recognize. Unavoidable design defects, quality variations and different usage patterns make it infeasible to foresee all possible faults, resulting in limited diagnostic coverage that can only deal with previously anticipated and modeled failures. This leads to missed detections and costly blind swapping of acceptable components because of one’s inability to accurately isolate the source of previously unseen anomalies. To circumvent these difficulties, a new paradigm for diagnostic systems is proposed and discussed in this paper. Its feasibility is demonstrated through application examples in automotive engine diagnostics.

Feeding attitudes, practices and traditional dietary beliefs of Chinese mothers with young children in Australia : a mixed methods study

Background and Objectives Obesity and some dietary related diseases are emerging health problems among Chinese immigrants and their children in developed countries. These health problems are closely linked to eating habits, which are established in the early years of life. Young children’s eating habits are likely to persist into later childhood and youth. Family environment and parental feeding practices have a strong effect on young children’s eating habits. Little information is available on the early feeding practices of Chinese mothers in Australia. The aim of this study was to understand the dietary beliefs, feeding attitudes and practices of Chinese mothers with young children who were recent immigrants to Australia. Methods Using a sequential explanatory design, this mixed methods study consisted of two distinct phases. Phase 1 (quantitative): 254 Chinese immigrant mothers of children aged 12 to 59 months completed a cross-sectional survey. The psychometric properties and factor structure of a Chinese version of the Child Feeding Questionnaire (CFQ, by Birch et al. 2001) were assessed and used to measure specific maternal feeding attitudes and controlling feeding practices. Other questions were developed from the literature and used to explore maternal traditional dietary beliefs and feeding practices related to their beliefs, perceptions of picky eating in children and a range of socioeconomic and acculturation factors. Phase 2 (qualitative): 21 mothers took part in a follow-up telephone interview to assist in explaining and interpreting some significant findings obtained in the first phase. Results Chinese mothers held strong traditional dietary beliefs and fed their children according to these beliefs. However, children’s consumption of non-core foods was high. Both traditional Chinese and Australian style foods were consumed by their children. Confirmatory factor analysis revealed that the original 7-factor model of the CFQ provided an acceptable fit to the data with minor modification. However, an alternative model with eight constructs in which two items related to using food rewards were separated from the original restriction construct, not only provided an acceptable fit to the data, but also improved the conceptual clarity of the constructs. The latter model included 24 items loading onto the following eight constructs: restriction, pressure to eat, monitoring, use of food rewards, perceived responsibility, perception of own weight, perception of child’s weight, and concern about child becoming overweight. The internal consistency of the constructs was acceptable or desirable (Cronbach’s α = .60 - .93). Mothers reported low levels of concern about their child overeating or becoming overweight, but high levels of controlling feeding practices: restriction, monitoring, pressure to eat and use of food rewards. More than one quarter of mothers misinterpreted their child’s weight status (based on mothers’ self-reported data). In addition, mothers’ controlling feeding practices independently predicted half of the variance and explained 16% of the variance in child weight status: pressuring the child to eat was negatively associated with child weight status (β = -0.30, p < .01) and using food rewards was positively associated with child weight status (β = 0.20, p < .05) after adjusting for maternal and child covariates. Monitoring and restriction were not associated with child weight status. Mothers’ perceptions of their child’s weight were positively associated with child weight status (β = 0.33, p < .01). Moreover, mothers reported that they mostly decided what (65%) and how much (80%) food their child ate. Mothers who decided what food their child ate were more likely to monitor (β = -0.17, p < .05) and restrict (β = -0.17, p < .05) their child’s food consumption. Mothers who let their child decide how much food their child ate were less likely to pressure their child to eat (β = -0.38, p < .01) and use food rewards (β = -0.24, p < .01). Mothers’ perceptions of picky eating behaviour were positively associated with their use of pressure (β = 0.21, p < .01) and negatively associated with monitoring (β = -0.16, p < .05) and perceptions of their child’s weight status (β = -0.13, p < .05). Qualitative data showed that pressuring to eat, monitoring and restriction of the child’s food consumption were common practices among these mothers. However, mothers stated that their motivation for monitoring and restricting was to ensure the child’s general health. Mothers’ understandings of picky eating behaviour in their children were consistent with the literature and they reported multiple feeding strategies to deal with it. Conclusion Chinese immigrant mothers demonstrated strong traditional dietary beliefs, a low level of concern for child weight, misperceptions of child weight status, and a high overall level of control in child feeding in this study. The Chinese version of the CFQ, which consists of eight constructs and distinguishes between the constructs using food rewards and restriction, is an appropriate instrument to assess feeding attitudes and controlling feeding practices among Chinese immigrant mothers of young children in Australia. Mothers’ feeding attitudes and practices were associated with children’s weight status and mothers’ perceptions of picky eating behaviour in children after adjusting for a range of socio-demographic maternal and child characteristics. Monitoring and restriction of children’s food consumption according to food selection may be positive feeding practices, whereas pressuring to eat and using food rewards appeared to be negative feeding practices in this study. In addition, the results suggest that these young children have high exposure to energy-dense, nutrient-poor food. There is a need to develop and implement nutrition interventions to improve maternal feeding practices and the dietary quality among children of Chinese immigrant mothers in Australia.

Metabolite profiling and pathway analysis of acute hepatitis rats by UPLC-ESI MS combined with pattern recognition methods

BACKGROUND & AIMS Metabolomics is comprehensive analysis of low-molecular-weight endogenous metabolites in a biological sample. It could enable mapping of perturbations of early biochemical changes in diseases and hence provide an opportunity to develop predictive biomarkers that could provide valuable insights into the mechanisms of diseases. The aim of this study was to elucidate the changes in endogenous metabolites and to phenotype the metabolic profiling of d-galactosamine (GalN)-inducing acute hepatitis in rats by UPLC-ESI MS. METHODS The systemic biochemical actions of GalN administration (ip, 400 mg/kg) have been investigated in male wistar rats using conventional clinical chemistry, liver histopathology and metabolomic analysis of UPLC- ESI MS of urine. The urine was collected predose (-24 to 0 h) and 0-24, 24-48, 48-72, 72-96 h post-dose. Mass spectrometry of the urine was analysed visually and via conjunction with multivariate data analysis. RESULTS Results demonstrated that there was a time-dependent biochemical effect of GalN dosed on the levels of a range of low-molecular-weight metabolites in urine, which was correlated with developing phase of the GalN-inducing acute hepatitis. Urinary excretion of beta-hydroxybutanoic acid and citric acid was decreased following GalN dosing, whereas that of glycocholic acid, indole-3-acetic acid, sphinganine, n-acetyl-l-phenylalanine, cholic acid and creatinine excretion was increased, which suggests that several key metabolic pathways such as energy metabolism, lipid metabolism and amino acid metabolism were perturbed by GalN. CONCLUSION This metabolomic investigation demonstrates that this robust non-invasive tool offers insight into the metabolic states of diseases.

Environments for Healthy Living (EFHL) Griffith Birth Cohort Study : background and methods

The health of an individual is determined by the interaction of genetic and individual factors with wider social and environmental elements. Public health approaches to improving the health of disadvantaged populations will be most effective if they optimise influences at each of these levels, particularly in the early part of the life course. In order to better ascertain the relative contribution of these multi-level determinants there is a need for robust studies, longitudinal and prospective in nature, that examine individual, familial, social and environmental exposures. This paper describes the study background and methods, as it has been implemented in an Australian birth cohort study, Environments for Healthy Living (EFHL): The Griffith Study of Population Health. EFHL is a prospective, multi-level, multi-year longitudinal birth cohort study, designed to collect information from before birth through to adulthood across a spectrum of eco-epidemiological factors, including genetic material from cord-blood samples at birth, individual and familial factors, to spatial data on the living environment. EFHL commenced the pilot phase of recruitment in 2006 and open recruitment in 2007, with a target sample size of 4000 mother/infant dyads. Detailed information on each participant is obtained at birth, 12-months, 3-years, 5-years and subsequent three to five yearly intervals. The findings of this research will provide detailed evidence on the relative contribution of multi-level determinants of health, which can be used to inform social policy and intervention strategies that will facilitate healthy behaviours and choices across sub-populations.

Inventory procedures for smallholder and community woodlots in the Philippines : methods, initial findings and insights

This paper details the processes and challenges involved in collecting inventory data from smallholder and community woodlots on Leyte Island, Philippines. Over the period from 2005 through to 2012, 253 woodlots at 170 sites were sampled as part of a large multidisciplinary project, resulting in a substantial timber inventory database. The inventory was undertaken to provide information for three separate but interrelated studies, namely (1) tree growth, performance and timber availability from private smallholder woodlots on Leyte Island; (2) tree growth and performance of mixed-species plantings of native species; and (3) the assessment of reforestation outcomes from various forms of reforestation. A common procedure for establishing plots within each site was developed and applied in each study, although the basis of site selection varied. A two-stage probability proportion to size sampling framework was developed to select smallholder woodlots for inclusion in the inventory. In contrast, community-based forestry woodlots were selected using stratified random sampling. Challenges encountered in undertaking the inventory were mostly associated with the need to consult widely before the commencement of the inventory and problems in identifying woodlots for inclusion. Most smallholder woodlots were only capable of producing merchantable volumes of less than 44 % of the site potential due to a lack of appropriate silviculture. There was a clear bimodal distribution of proportion that the woodlots comprised of the total smallholding area. This bimodality reflects two major motivations for smallholders to establish woodlots, namely timber production and to secure land tenure.

Outdoor Worker Sun Protection Project : a mixed methods intervention to improve sun safety among outdoor workers

Queensland, Australia has one of the highest rates of skin cancer in the world. Outdoor workers are regularly exposed to high doses of ultraviolet radiation, and are at increased risk to develop non-melanoma and melanoma skin cancers. In 2010, a health promotion intervention to improve sun protection among outdoor workers in Queensland commenced. The intervention employed a mixed methods approach and a participatory action research framework. Fourteen workplaces were recruited from building and construction, rural and farming, local government, and public sector organisations. Management and workers were engaged in cycles of assessment, reflection and discussion, planning, implementation and reassessing, over a 14-month intervention period. Overall, at least one workplace representative from each workplace (range 1-3) and in depth focus groups were held with a subset of workers (range 3-16) to assess sun safe behaviours pre and post intervention. Workers’ attitudes, beliefs, knowledge and willingness to engage in sun protection differed depending on workplace characteristics and support. A familiar theme among workers spoke of sun safety as being “common sense” and the “workers individual responsibility”. Often there was a discrepancy in the perceptions of the workers, compared to the view of workplace representatives and the workplaces position or policy on sun safety. In larger workplaces, especially Government Departments, workers were more aware and followed sun safe practices compared to smaller workplaces where sun safety was not a high priority. These results indicate that a workplace culture which places high values on safety and polices more broadly may also have a positive effect on sun safety among outdoor workers as well. In addition, the specific characteristics of the workplace and the outdoor work tasks influence workers willingness to engage in sun safety measures.

Tensile properties of pumpkin peel and flesh tissue and review of current testing methods

In South and Southeast Asia, postharvest loss causes material waste of up to 66% in fruits and vegetables, 30% in oilseeds and pulses, and 49% in roots and tubers. The efficiency of postharvest equipment directly affects industrial-scale food production. To enhance current processing methods and devices, it is essential to analyze the responses of food materials under loading operations. Food materials undergo different types of mechanical loading during postharvest and processing stages. Therefore, it is important to determine the properties of these materials under different types of loads, such as tensile, compression, and indentation. This study presents a comprehensive analysis of the available literature on the tensile properties of different food samples. The aim of this review was to categorize the available methods of tensile testing for agricultural crops and food materials to investigate an appropriate sample size and tensile test method. The results were then applied to perform tensile tests on pumpkin flesh and peel samples, in particular on arc-sided samples at a constant loading rate of 20 mm min-1. The results showed the maximum tensile stress of pumpkin flesh and peel samples to be 0.535 and 1.45 MPa, respectively. The elastic modulus of the flesh and peel samples was 6.82 and 25.2 MPa, respectively, while the failure modulus values were 14.51 and 30.88 MPa, respectively. The results of the tensile tests were also used to develop a finite element model of mechanical peeling of tough-skinned vegetables. However, to study the effects of deformation rate, moisture content, and texture of the tissue on the tensile responses of food materials, more investigation needs to be done in the future.