Um estudo exploratório sobre as práticas socio-ambientais de empresas multinacionales no setor de mineração do Peru

O presente trabalho tem por objetivo conhecer as práticas socio-ambientais no setor de mineração do Peru. Setor que esta dominada pela presença de empresas transnacionais que se encontram com duas realidades de regulamentação de meio ambientais muito discordantes, a primeira, as normas corporativas onde se encontra a matriz e, a segunda, a regulamentação do país onde esta a subsidiaria, neste caso o Peru. Com a internacionalização do tema socio-ambiental, se dá a devida importância ao tema da Responsabilidade Social Corporativa, já que as empresas transnacionais estão pressionadas a manter uma boa imagem internacional, que pode ser vulnerável a criticas negativas em relação à heterogeneidade, já que suas praticas socio-ambientais têm que ser as mesmas em qualquer parte do mundo. Na presente dissertação se enfatiza as praticas socio-ambientais das empresas com relação às comunidades circundantes, sendo um tema pouco difundido na mineração peruana. As desconformidades das comunidades frente aos projetos de mineração constituem o maior problema social atual, gerando a paralisação das atividades nesse setor. O Peru não tem Ministério do Meio Ambiente, embora exista um Conselho Nacional do Meio Ambiente (CONAM) que é um organismo público descentralizado e, esta aderido ao âmbito da Presidência do Conselho de Ministros. Nesta investigação se analisa a função do Ministério de Energia e Minas do Peru, já que ele é um ente que incentiva a promoção de investimento privada no setor de energia e minas e, por outro lado, mediante a Direção Geral de Assuntos Ambientais do Ministério de Energia e Minas aplica a guia de gestão ambiental emitidas pelo CONAM. Finalmente, no estudo de caso, são analisadas duas empresas transnacionais maiores do setor de mineração peruano, aplicando entrevistas e um questionário com perguntas abertas para poder conhecer suas praticas socio-ambientais. Desenvolve-se uma análise dos resultados obtidos no estudo de caso, utilizando o referencial teórico para situar a realidade peruana, numa realidade internacional. Pelos dados obtidos, podemos interpretar que as empresas estudadas não se encaixam totalmente nos parâmetros internacionais do auto-regulamentação. Observamos a falta de políticas públicas sócio-ambiental, é por esse motivo, a conclusão desta investigação propõe a criação e aplicação de políticas públicas a dois problemas socio-ambientais, o primeiro, a geração de emprego indireto e a segunda, a recuperação dos passivos ambientais.

Novel catalyst systems based on Ni(II), Ti(IV), and Cr(III) complexes for oligo-and polymerization of ethylene

The complex of Brookhart Ni(α-diimine)Cl2 (1) (α-diimine = 1,4-bis(2,6- diisopropylphenyl)-acenaphthenediimine) has been characterized after impregnation on silica (S1) and MAO-modified silicas (4.0, 8.0 and 23.0 wts.% Al/SiO2 called S2, S3 and S4, respectively). The treatment of these heterogeneous systems with MAO produces some active catalysts for the polymerization of the ethylene. A high catalytic activity has been gotten while using the system supported 1/S3 (196 kg of PE/mol[Ni].h.atm; toluene, Al/Ni = 1000, 30ºC, 60 min and atmospheric pressure of ethylene). The effects of polymerization conditions have been tested with the catalyst supported in S2 and the best catalytic activity has been gotten with solvent hexane, MAO as cocatalyst, molar ratio Al/Ni of 1000 and to the temperature of 30°C (285 kg of PE/mol[Ni].h.atm). When the reaction has been driven according to the in situ methodology, the activity practically doubled and polymers showed some similar properties. Polymers products by the supported catalysts showed the absence of melting fusion, results similar to those gotten with the homogeneous systems by DSC analysis. But then, polymers gotten with the transplanted system present according to the GPC’s curves the polydispersity (MwD) varies between 1.7 and 7.0. A polyethylene blend (BPE/LPE) was prepared using the complex Ni(α-diimine)Cl2 (1) (α-diimine = 1,4-bis(2,6-diisopropylphenyl)-acenaphthenediimine) and {TpMs*}TiCl3 (2) (TpMs* = hydridobis(3-mesitylpyrazol-1-yl)(5-mesitylpyrazol-1-yl)) supported in situ on MAO-modified silica (4.0 wts. -% Al/SiO2, S2). Reactions of polymerization of ethylene have been executed in the toluene in two different temperatures (0 and 30°C), varying the molars fraction of nickel (xNi), and using MAO as external cocatalyst. To all temperatures, the activities show a linear variation tendency with xNi and indicate the absence of the effect synergic between the species of nickel and the titanium. The maximum of activity have been found at 0°C. The melting temperature for the blends of polyethylene produced at 0 °C decrease whereas xNi increases indicating a good compatibility between phases of the polyethylene gotten with the two catalysts. The melting temperature for the blends of polyethylene showed be depend on the order according to which catalysts have been supported on the MAO-modified silica. The initial immobilization of 1 on the support (2/1/S2) product of polymers with a melting temperature (Tm) lower to the one of the polymer gotten when the titanium has been supported inicially (1/2/S2). The observation of polyethylenes gotten with the two systems (2/1/S2 and 1/2/S2) by scanning electron microscopy (SEM) showed the spherical polymer formation showing that the spherical morphology of the support to been reproduced. Are described the synthesis, the characterization and the catalytic properties for the oligomerization of the ethylene of four organometallics compounds of CrIII with ligands ([bis[2-(3,5-dimethyl-1-pyrazolyl)ethyl]amine] chromium (III) chloride (3a), [bis[2-(3,5- dimethyl-l-pyrazolyl)ethyl]benzylamine] chromium (III) chloride (3b), [bis[2-(3,5-dimethyl-lpyrazolyl) ethyl]ether] chromiun(III)chloride (3c), [bis[2-(3-phenyl-lpyrazolyl) ethyl]ether]chromiun(III)chloride (3d)). In relation of the oligomerization, at exception made of the compounds 3a, all complex of the chromium showed be active after activation with MAO and the TOF gotten have one effect differentiated to those formed with CrCl3(thf)3. The coordination of a tridentate ligand on the metallic center doesn't provoke any considerable changes on the formation of the C4 and C6, but the amount of C8 are decrease and the C10 and C12+ have increased. The Polymers produced by the catalyst 3a to 3 and 20 bar of ethylene have, according to analyses by DSC, the temperatures of fusion of 133,8 and 136ºC respectively. It indicates that in the two cases the production of high density polyethylene. The molar mass, gotten by GPC, is 46647 g/mols with MwD = 2,4 (3 bar). The system 3c/MAO showed values of TOF, activity and selectivity to different α-olefins according to the pressure of ethylene uses. Himself that shown a big sensibility to the concentration of ethylene solubilized.

Implante endoscópico no esôfago distal de polimetilmetacrilato para controle do refluxo gastrofágico : estudo experimental em modelo animal

XIXA doença do refluxo gastroesofágico (DRGE) comumente afeta o esôfago e provavelmente é a condição mais prevalente no segmento alto do trato gastrointestinal, acometendo entre 5 e 45% da população ocidental. A terapêutica atual para essa doença além de medidas gerais e dietéticas, inclui tratamento farmacológico e/ou cirurgia. Ambos podem ser eficazes, mas apresentam elevado custo financeiro. O tratamento com fármacos pode apresentar baixa aderência medicamentosa e a cirurgia tem baixa, mas não desprezível, morbidade e mortalidade. Idealmente o tratamento da DRGE deveria ser eficaz, com baixo risco e com baixo custo. Objetivos: 1. Desenvolver um modelo experimental em suínos para o estudo do Refluxo Gastroesofágico através da Pressão e do Volume de Vazão Gástricos; 2. Avaliar a eficácia do implante endoscópico de PMMA ao nível do Esfíncter Esofágico Inferior (EEI) para aumentar a Pressão de Vazão Gástrica, o Volume de Vazão Gástrico e a Pressão Basal do EEI; 3. Descrever as reações histológicas associadas ao implante de PMMA. Material e Métodos: Suínos da raça Large White, do sexo feminino com 8 semanas de vida foram estudados no experimento. Foi realizada manometria do esfíncter esofágico inferior com registro da pressão basal com cateter de perfusão com água e técnica de retirada lenta. Calculou-se, também, a extensão do EEI. Após, gastrostomia era realizada com colocação intragástrica da extremidade distal de uma sonda de Foley com três vias e um cateter de pHmetria esofágica introduzido via oral com o sensor distal posicionado 5 cm acima do bordo superior de esfíncter esofágico inferior. Iniciava-se, XXentão, a infusão contínua no estômago de uma solução de HCl a 0,02N com medida e registro simultâneos da Pressão e do Volume de Vazão Gástricos e do pH esofágico. Definiu-se a Pressão de Vazão Gástrica (PVG) e o Volume de Vazão Gástrico quando houve brusca e sustentada acidificação do esôfago distal (pH<3). Após, introduzia-se um tubo metálico (Tubo Introdutor ou TI) via oral e, em seguida, o endoscópio, seguindo ambos até o esôfago distal. Cateter de nylon com agulha calibre 16 era introduzido pelo tubo introdutor e o PMMA implantado na área correspondente ao EEI com uma pistola dosadora volumétrica que permitia a injeção de volumes prédeterminados em 3 ou 4 pontos da submucosa (total por ponto = 0,73 ml de PMMA). As medidas de PVG, VVG e pressão basal do EEI foram repetidas após 28 dias, sacrificando-se os animais e removendo-se esôfago médio e distal, junção esofagogástrica, fundo e corpo gástricos para estudo histológico. Previamente ao experimento, três projetos pilotos foram desenvolvidos. O primeiro designado como “Projeto Piloto: Refluxo Gastroesofágico por pHmetria de 24H” (RGE 24H) buscou a via de acesso transnasal para registro de pHmetria por 24 horas. No segundo, designado “Projeto Piloto: Esofagostomia”, para confirmação de refluxo gastroesofágico espontâneo em suínos da raça Large White, utilizou-se anestesia com associação de tiletamina 125 mg e zolazepam 125 mg em combinação com um sedativo, a xilazina a 2% . A pHmetria foi mantida por 24 horas. Os dados descritos por Kadirkamanathan et al. não foram reproduzidos no nosso laboratório. Optou-se então pela realização de um terceiro projeto, “Projeto Piloto: Gastrostomia” para induzir refluxo gastroesofágico através de um modelo experimental e testar a reprodutibilidade da Pressão de Vazão Gástrica. Obteve-se sucesso. Resultados: Trinta e sete animais foram estudados em 60 intervenções no Laboratório de motilidade experimental. O projeto piloto “RGE:24h” foi abandonado após perda de 5 animais pela anestesia com halotano e, solucionada esta questão, a sistemática infecção do tecido celular subcutâneo nasal, dificultando a manutenção do cateter de phmetria em outros 5 animais. No “Projeto Piloto: Esofagostomia”, em cinco animais estudados (cada animal em duas ocasiões diferentes) não se reproduziram os achados de refluxo espontâneo. No terceiro projeto “Projeto Piloto: Gastrostomia” quatro animais foram estudados em dois momentos diferentes obtendo-se sucesso e reprodutibilidade XXIdos dados. Criado o modelo experimental, quatorze suínos foram submetidos ao experimento com implante endoscópico de PMMA com os seguintes resultados: A média dos pesos com 8 semanas de idade foi 14,98 ± 2,43 e 28 dias após o implante, 20,26 ± 3,68. O ganho ponderal foi considerado normal para a espécie. A Pressão de Vazão Gástrica média no dia 1 foi 8,08 mmHg e no dia 28, 10,69mmHg (Teste t de Student: t = 2,72 gl = 13 p = 0,017). Os Volumes de Vazão Gástricos médios foram: 392,86 ml para o dia 1 e 996,71 ml no dia 28 (teste t de Student: t = 11,66 gl = 13 p< 0,001). A Pressão Basal do EEI e o comprimento do esfíncter, não apresentaram diferenças estatisticamente significativas. PMMA foi identificado como depósitos de grandes vacúolos no tecido intersticial ao exame histológico da junção esofagogástrica associado a histiócitos, plasmócitos e presença de células gigantes tipo Langhans indicando reação tecidual de corpo estranho em todos os animais. Fibrose e macrófagos com vacúolos intracelulares estiveram presentes em menor freqüência. Conclusões: 1. O modelo experimental, em suínos, desenvolvido viabilizou o estudo do Refluxo Gastroesofágico através da Pressão de Vazão Gástrica e Volume de Vazão Gástrico; 2. O implante de PMMA, no presente estudo, aumentou a Pressão de Vazão e o Volume de Vazão Gástricos, mas não a Pressão Basal do EEI, nem tampouco aumentou o seu comprimento; 3. Depósito de PMMA implantado e evidência de processo inflamatório crônico e reação tecidual de corpo estranho foi encontrada no local do implante de PMMA. Macrófagos com vacúolos intracelulares e fibrose foram encontrados com menos freqüência.

Sistemas de produção de carvão vegetal existentes no Brasil: uma análise de viabilidade econômica

O carvão vegetal tem um papel de destaque entre as biomassas consumidas no Brasil. Seu uso em larga escala na indústria siderúrgica para a produção de ferro gusa fez do país um dos maiores produtores e consumidores mundiais de carvão vegetal. A matéria-prima abundante, bem como a falta de preocupação com fatores ambientais e sociais, permitiu no passado que se atentasse apenas ao fator econômico; e a tecnologia de produção deste combustível/insumo se desenvolveu muito pouco ao longo de quase toda a sua história no Brasil até os anos mais recentes. Nas duas últimas décadas, quando se intensificou a preocupação social e ambiental e esses fatores ganharam relevância na análise da viabilidade de projetos tanto a serem implantados, quanto já existentes, a produção de carvão vegetal passou a ser identificada como extremamente rudimentar e impactante ao meio ambiente e sociedade onde se localiza. Neste trabalho buscou-se analisar a viabilidade econômica de quatro sistemas de produção de carvão existentes no Brasil. O sistema mais rudimentar, comumente chamado de “rabo quente”, um sistema ainda de alvenaria, com um pouco mais desenvolvimento tecnológico conhecido como forno retangular, e dois sistemas que utilizam fornos metálicos para buscar menor tempo do processo de carbonização (devido ao mais rápido resfriamento do sistema) e que têm, ambos, uma preocupação ambiental maior e buscam emitir menos poluentes e oferecer uma condição de trabalho mais adequada, refletindo também positivamente sob o aspecto sócio-ambiental. Percebe-se que em termos de implantação, obviamente, os sistemas que envolvem um pouco mais de tecnologia são bem mais dispendiosos em investimento inicial, porém, há resultados animadores do ponto de vista de retorno do investimento e possibilidades de agregação de valor que tendem a atrair o investimento especialmente dos grandes grupos siderúrgicos consumidores, que têm se preocupado cada vez mais em investir tanto na produção de matéria-prima, com grandes áreas de reflorestamento, quanto na produção sustentável do carvão vegetal.

Economic recovery from the Argentine great depression : institutions, expectations, and the change of macroeconomic regime

This work explores how Argentina overcame the Great Depression and asks whether active macroeconomic interventions made any contribution to the recovery. In particular, we study Argentine macroeconomic policy as it deviated from gold-standard orthodoxy after the final suspension of convertibility in 1929. As elsewhere, fiscal policy in Argentina was conservative, and had little power to smooth output. Monetary policy became heterodox after 1929. The first and most important stage of institutional change took place with the switch from a metallic monetary regime to a fiduciary regime in 1931; the Caja de Conversión (Conversion Office, a currency board) began rediscounting as a means to sterilize gold outflows and avoid deflationary pressures, thus breaking from orthodox "mIes of the game." However, the actual injections of liquidity were small' and were not enough to fully offset the incipient monetary contractions: the "Keynes" effect was weak or negative. Rather, recovery derived from changes in beliefs and expectations surrounding the shift in the monetary and exchange-rate regime,and the delinking of gold flows and the money base. Agents perceivod a new regime, as shown by the path of consumption, investment, and estimated ex ante real interest rates: the "Mundell" effect was dominant. Notably, this change of regime predated a later, and supposedly more significant, stage of institutional reform, namely the creation of the central bank in 1935. Still, the extent of intervention was weak, and insufficient to fully offset externaI shocks to prices and money. Argentine macropolicy was heterodox in terms of the change of regime, but still conservative in terms of the tentative scope of the measures taken .

Indústria de máquinas agrícolas no Brasil: um modelo para estimação da demanda de tratores para o triênio 2016 – 2018

O objetivo desta dissertação foi estimar a demanda de tratores agrícolas para o mercado brasileiro no triênio 2016-2018, utilizando-se para isto de técnicas de econometria de séries temporais, neste caso, modelos univariados da classe ARIMA e SARIMA e ou multivariados SARIMAX. Justifica-se esta pesquisa quando se observa a indústria de máquinas agrícolas no Brasil, dados os ciclos econômicos e outros fatores exógenos aos fundamentos econômicos da demanda, onde esta enfrenta muitos desafios. Dentre estes, a estimação de demanda se destaca, pois exerce forte impacto, por exemplo, no planejamento e custo de produção de curto e médio prazo, níveis de inventários, na relação com fornecedores de materiais e de mão de obra local, e por consequência na geração de valor para o acionista. Durante a fase de revisão bibliográfica foram encontrados vários trabalhos científicos que abordam o agronegócio e suas diversas áreas de atuação, porém, não foram encontrados trabalhos científicos publicados no Brasil que abordassem a previsão da demanda de tratores agrícolas no Brasil, o que serviu de motivação para agregar conhecimento à academia e valor ao mercado através deste. Concluiu-se, após testes realizados com diversos modelos que estão dispostos no texto e apêndices, que o modelo univariado SARIMA (15,1,1) (1,1,1) cumpriu as premissas estabelecidas nos objetivos específicos para escolha do modelo que melhor se ajusta aos dados, e foi escolhido então, como o modelo para estimação da demanda de tratores agrícolas no Brasil. Os resultados desta pesquisa apontam para uma demanda de tratores agrícolas no Brasil oscilando entre 46.000 e 49.000 unidades ano entre os anos de 2016 e 2018.

The Effect of Residence Time on the Tensile Properties of Superelastic and Thermal Activated Ni-Ti Orthodontic Wires

Since the 1980s, different devices based on superelastic alloys have been developed to fulfill orthodontic applications. Particularly in the last decades several researches have been carried out to evaluate the mechanical behavior of Ni-Ti alloys, including their tensile, torsion and fatigue properties. However, studies regarding the dependence of elastic properties on residence time of Ni-Ti wires in the oral cavity are scarce. Such approach is essential since metallic alloys are submitted to mechanical stresses during orthodontic treatment as well as pH and temperature fluctuations. The goal of the present contribution is to provide elastic stress-strain results to guide the orthodontic choice between martensitic thermal activated and austenitic superelastic Ni-Ti alloys. From the point of view of an orthodontist, the selection of appropriate materials and the correct maintenance of the orthodontic apparatus are essential needs during clinical treatment. The present work evaluated the elastic behavior of Ni-Ti alloy wires with diameters varying from 0.014 to 0.020 inches, submitted to hysteresis tensile tests with 8% strain. Tensile tests were performed after periods of use of 1, 2 and 3 months in the oral cavity of patients submitted to orthodontic treatment. The results from the hysteresis tests allowed to exam the strain range covered by isostress lines upon loading and unloading, as well as the residual strain after unloading for both superelastic and thermal activated Ni-Ti wires. Superelastic Ni-Ti wires exhibited higher load isostress values compared to thermal activated wires. It was found that such differences in the load isostress values can increase with increasing residence time.

Estudo da sinterização do aço inox 316L reforçado com 3% Carbeto de Tântalo - TaC

The present work shows a contribution to the studies of development and solid sinterization of a metallic matrix composite MMC that has as starter materials 316L stainless steel atomized with water, and two different Tantalum Carbide TaC powders, with averages crystallite sizes of 13.78 nm and 40.66 nm. Aiming the metallic matrix s density and hardness increase was added different nanometric sizes of TaC by dispersion. The 316L stainless steel is an alloy largely used because it s high resistance to corrosion property. Although, its application is limited by the low wear resistance, consequence of its low hardness. Besides this, it shows low sinterability and it cannot be hardened by thermal treatments traditional methods because of the austenitic structure, face centered cubic, stabilized mainly in nickel presence. Steel samples added with TaC 3% wt (each sample with different type of carbide), following a mechanical milling route using conventional mill for 24 hours. Each one of the resulted samples, as well as the pure steel sample, were compacted at 700 MPa, room temperature, without any addictive, uniaxial tension, using a 5 mm diameter cylindrical mold, and quantity calculated to obtain compacted final average height of 5 mm. Subsequently, were sintered in vacuum atmosphere, temperature of 1290ºC, heating rate of 20ºC/min, using different soaking times of 30 and 60 min and cooled at room temperature. The sintered samples were submitted to density and micro-hardness analysis. The TaC reforced samples showed higher density values and an expressive hardness increase. The complementary analysis in optical microscope, scanning electronic microscope and X ray diffractometer, showed that the TaC, processed form, contributed with the hardness increase, by densification, itself hardness and grains growth control at the metallic matrix, segregating itself to the grain boarders

Análise do comportamento reológico de pastas de cimento contendo resíduos de pneu para poços de petróleo

The low tenacity presented by the Portland cement pastes used in the oil wells cementation has been motivating several researches with attention focused on alternative materials. Additives have been developed to generate flexible pastes with mechanical resistance capable to support the expansions and retractions of the metallic covering of the wells that submit to the steam injection, technique very used to increase the recovery factor in oil reservoirs with high viscosity. A fresh paste with inadequate rheological behavior may commit the cementation process seriously, involving flaws that affect the performance of the paste substantially in the hardened state. This work proposes the elaboration and the rheological analysis of Portland cement pastes with addition of residues of rubber tire in several proportions, with the aim of minimizing the damages provoked in the hem cementing of these wells. By thermogravimetric analysis, the particles of eraser that go by the sieve of 0,5mm (35 mesh) opening and treated superficially with NaOH solution of 1 mol/L presented appropriate thermal resistance for wells that submit to thermal cyclic. The evaluation of the study based on the results of the rheological analysis of the pastes, complemented by the mechanical analysis, thickening, stability, tenor of free water and filtrate loss, being used as parameter a paste reference, without rubber addition. The results showed satisfactory rheology, passive of few corrections; considerable loss of mechanical resistance (traction and compression), compensated by earnings of tenacity, however with established limits for its application in oil wells; satisfactory stability, free water and thickening time

Caracterização termo-mecânica de interconectores metálicos recobertos com filmes de LaCrO3

The cells unitaria of the solid oxide fuel cell are separated by means of interconnects, which serve as electrical contact between the cells. Lanthanum Chromite (LaCrO3) has been the most common material used as interconnect in solid oxide fuel cells. Reducing the operating temperature around 800 º C of cells to solid oxide fuel make possibilite the use of metallic interconnects as an alternative to ceramic LaCrO3. Metallic interconnects have advantages over ceramic interconnects such as high thermal conductivity, electricity, good ductility, low cost, good physical and mechanical properties. In this work evaluate the thermo-mechanical properties of the metallic substrate and coated metallic substrate with the ceramic LaCrO3 film via spray-pyrolysis, in order to demonstrate the feasibility of using this material as a component of a fuel cell solid oxide. The materials were characterized by X-ray diffraction, oxidation behavior, mechanical strength, optical microscopy (OM) and scanning electron microscopy (SEM). The X-ray diffraction proved the formation phase of the LaCrO3 on the metallic substrate and the identification of the phases formed after the oxidative test and mechanical strength at high temperature. The oxidation behavior showed the increased oxidation resistance of the coated metallic substrate. It was noted that the mechanical resistance to bending of the coated metallic substrate only increases at room temperature. The optical microscopy (OM) has provided an assessment of both the metallic substrate and the LaCrO3 film deposited on the metal substrate that, in comparison with the micrographs obtained from SEM. The SEM one proved the formation of Cr2O3 layer on the metallic substrate and stability of LaCrO3 film after oxidative test, it can also observe the displacement of the ceramic LaCrO3 film after of mechanical testing and mapping of the main elements as chromium, manganese, oxygen, lanthanum in samples after the thermo-mechanical tests.

Avaliação espectrofotométrica do manchamento de resinas odontológicas contendo nanopartículas

Composite resins have been subjected to structural modifications aiming at improved optical and mechanical properties. The present study consisted in an in vitro evaluation of the staining behavior of two nanohybrid resins (NH1 and NH2), a nanoparticulated resin (NP) and a microhybrid resin (MH). Samples of these materials were prepared and immersed in commonly ingested drinks, i.e., coffee, red wine and acai berry for periods of time varying from 1 to 60 days. Cylindrical samples of each resin were shaped using a metallic die and polymerized during 30 s both on the bottom and top of its disk. All samples were polished and immersed in the staining solutions. After 24 hours, three samples of each resin immersed in each solution were removed and placed in a spectrofotome ter for analysis. To that end, the samples were previously diluted in HCl at 50%. Tukey tests were carried out in the statistical analysis of the results. The results revealed that there was a clear difference in the staining behavior of each material. The nanoparticulated resin did not show better color stability compared to the microhybrid resin. Moreover, all resins stained with time. The degree of staining decreased in the sequence nanoparticulated, microhybrid, nanohybrid MH2 and MH1. Wine was the most aggressive drink followed by coffee and acai berry. SEM and image analysis revealed significant porosity on the surface of MH resin and relatively large pores on a NP sample. The NH2 resin was characterized by homogeneous dispersion of particles and limited porosity. Finally, the NH1 resin depicted the lowest porosity level. The results revealed that staining is likely related to the concentration of inorganic pa rticles and surface porosity

Sinterização de aço inoxidável reforçado com partículas nanométricas dispersas de carbeto de nióbio - NbC

Metal powder sintering appears to be promising option to achieve new physical and mechanical properties combining raw material with new processing improvements. It interest over many years and continue to gain wide industrial application. Stainless steel is a widely accepted material because high corrosion resistance. However stainless steels have poor sinterability and poor wear resistance due to their low hardness. Metal matrix composite (MMC) combining soft metallic matrix reinforced with carbides or oxides has attracted considerable attention for researchers to improve density and hardness in the bulk material. This thesis focuses on processing 316L stainless steel by addition of 3% wt niobium carbide to control grain growth and improve densification and hardness. The starting powder were water atomized stainless steel manufactured for Höganäs (D 50 = 95.0 μm) and NbC produced in the UFRN and supplied by Aesar Alpha Johnson Matthey Company with medium crystallite size 16.39 nm and 80.35 nm respectively. Samples with addition up to 3% of each NbC were mixed and mechanically milled by 3 routes. The route1 (R1) milled in planetary by 2 hours. The routes 2 (R2) and 3 (R3) milled in a conventional mill by 24 and 48 hours. Each milled samples and pure sample were cold compacted uniaxially in a cylindrical steel die (Ø 5 .0 mm) at 700 MPa, carried out in a vacuum furnace, heated at 1290°C, heating rate 20°C stand by 30 and 60 minutes. The samples containing NbC present higher densities and hardness than those without reinforcement. The results show that nanosized NbC particles precipitate on grain boundary. Thus, promote densification eliminating pores, control grain growth and increase the hardness values

Influência do número de refundições da liga Ni-Cr-Mo-Ti sobre as propriedades de próteses metalocerâmicas

A frequently encountered difficulty in oral prosthetics is associated with the loss of metallic alloys during the melting stage of the production of metal-ceramic replacement systems. Remelting such materials could impar their use in oral rehabilitation due to loss in esthetics, as well as in the chemical, physical, electrochemical and mechanical properties. Nowadays, the Ni-Cr-Mo-Ti alloy is widely used in metal-ceramic systems. Manufacturers state that this material can be remelted without significant alterations in its behavior, however little has been established as to the changes in the performance of this alloy after successive remelting, which is common practice in oral prosthetics. Therefore, the objective of this study was to evaluate possible changes in the esthetics and associated properties of metalceramic samples consisting of Ni-Cr-Mo-Ti and dental porcelain. Three to five remelting steps were carried out. The results revealed that Ni-Cr-Mo-Ti can be safely used even after three remelting steps. Further remelting significantly affect the characteristics of the alloys and should not be recommended for the manufacture of metal-ceramic systems

Construção, caracterização e aplicação de eletrodos para descarga por arco de cátodo oco

The system built to characterize electrodes and, consequently, deposited fine films are constituted by a hollow cathode that works to discharges and low pressures (approximately 10-3 to 5 mbar), a source DC (0 to 1200 V), a cylindrical camera of closed borossilicato for flanges of stainless steel with an association of vacuum bombs mechanical and spread. In the upper flange it is connected the system of hollow cathode, which possesses an entrance of gas and two entrances for its refrigeration, the same is electrically isolated of the rest of the equipment and it is polarized negatively. In front of the system of hollow cathode there is a movable sample in stainless steel with possibility of moving in the horizontal and vertical. In the vertical, the sample can vary its distance between 0 and 70 mm and, in the horizontal, can leave completely from the front of the hollow cathode. The sample and also the cathode hollow are equipped with cromel-alumel termopares with simultaneous reading of the temperatures during the time of treatment. In this work copper electrodes, bronze, titanium, iron, stainless steel, powder of titanium, powder of titanium and silício, glass and ceramic were used. The electrodes were investigated relating their geometry change and behavior of the plasma of the cavity of hollow cathode and channel of the gas. As the cavity of hollow cathode, the analyzed aspects were the diameter and depth. With the channel of the gas, we verified the diameter. In the two situations, we investigated parameters as flow of the gas, pressure, current and applied tension in the electrode, temperature, loss of mass of the electrode with relationship at the time of use. The flow of gas investigated in the electrodes it was fastened in a work strip from 15 to 6 sccm, the constant pressure of work was among 2.7 to 8 x 10-2 mbar. The applied current was among a strip of work from 0,8 to 0,4 A, and their respective tensions were in a strip from 400 to 220 V. Fixing the value of the current, it was possible to lift the curve of the behavior of the tension with the time of use. That curves esteem in that time of use of the electrode to its efficiency is maximum. The temperatures of the electrodes were in the dependence of that curves showing a maximum temperature when the tension was maximum, yet the measured temperatures in the samples showed to be sensitive the variation of the temperature in the electrodes. An accompaniment of the loss of mass of the electrode relating to its time of use showed that the electrodes that appeared the spherical cavities lost more mass in comparison with the electrodes in that didn't appear. That phenomenon is only seen for pressures of 10-2 mbar, in these conditions a plasma column is formed inside of the channel of the gas and in certain points it is concentrated in form of spheres. Those spherical cavities develop inside of the channel of the gas spreading during the whole extension of the channel of the gas. The used electrodes were cut after they could not be more used, however among those electrodes, films that were deposited in alternate times and the electrodes that were used to deposit films in same times, those films were deposited in the glass substrata, alumina, stainless steel 420, stainless steel 316, silício and steel M2. As the eletros used to deposit films in alternate time as the ones that they were used to deposit in same times, the behavior of the thickness of the film obeyed the curve of the tension with relationship the time of use of the electrode, that is, when the tension was maximum, the thickness of the film was also maximum and when the tension was minimum, the thickness was minimum and in the case where the value of the tension was constant, the thickness of the film tends to be constant. The fine films that were produced they had applications with nano stick, bio-compatibility, cellular growth, inhibition of bacterias, cut tool, metallic leagues, brasagem, pineapple fiber and ornamental. In those films it was investigated the thickness, the adherence and the uniformity characterized by sweeping electronic microscopy. Another technique developed to assist the production and characterization of the films produced in that work was the caloteste. It uses a sphere and abrasive to mark the sample with a cap impression, with that cap form it is possible to calculate the thickness of the film. Through the time of life of the cathode, it was possible to evaluate the rate of waste of its material for the different work conditions. Values of waste rate up to 3,2 x 10-6 g/s were verified. For a distance of the substratum of 11 mm, the deposited film was limited to a circular area of 22 mm diameter mm for high pressures and a circular area of 75 mm for pressure strip. The obtained films presented thickness around 2,1 µm, showing that the discharge of arch of hollow cathode in argon obeys a curve characteristic of the tension with the time of life of the eletrodo. The deposition rate obtained in this system it is of approximately 0,18 µm/min

Obtenção de filtro cerâmico a partir da diatomita e casca de arroz carbonizada visando tratamento de efluente têxtil

The effluents released by the textile industry have high concentrations of alkali, carbohydrates, proteins, in addition to colors containing heavy metals. Therefore, a filter was prepared aiming primarily to the removal of color. In order to prepare this filter, rice hulls and diatomite were used, which have in their structure, basically amorphous hydrated silica. The silica exists in three crystalline forms: quartz, tridymite and cristobalite. In accordance with the above considerations, this study was divided into two stages; the first corresponds to the preparation of the filter and the second to carry out the tests in the effluent/filter in order to verify the efficiency of the color removal. First, the raw material was subjected to a chemical analysis and XRD, and then the diatomite was mixed, via humid, with a planetarium windmill with 20 %, 40 %, 60 % and 80 % of rice husk ash. To the mixture, 5 % carboxymethylcellulose (CMC) was added as a binder at room temperature. The samples were uniaxially compacted into metallic matrix of 0.3 x 0.1 cm² of area at a pressure of 167 MPa by means of hydraulic press and then sintered at temperatures of 1,000 °C, 1,200 °C and 1,400 °C for 1 h and submitted to granulometry test using laser, linear retraction, water absorption, apparent porosity and resistance to bending, DTA, TMA and XRD. To examine the pore structure of the samples scanning electron microscope (SEM) was used. Also tests were carried out in a mercury porosimeter to verify the average size of the pores and real density of the samples. In the second stage, samples of the effluent were collected from a local industry, whose name will be preserved, located in Igapó, in the State of Rio Grande do Norte - RN. The effluent was first pretreated before filtration and then subjected to a treatment of flotation. The effluent was then characterized before and after filtration, with parameters of color, turbidity, suspended solids, pH, chemical and biochemical oxygen demand (COD and BOD). Thus, through the XRD analysis the formation of cristobalite α in all samples was observed. The best average size of pore was found to be 1.75 μm with 61.04 % apparent porosity, thus obtaining an average 97.9 % color removal and 99.8 % removal of suspended solid