Laser induced damage threshold at 355 and 1064 nm of Ta2O5 films of different phases

Ta2O5 films are deposited on fused silica substrates by conventional electron beam evaporation method. By annealing at different temperatures, Ta2O5 films of amorphous, hexagonal and orthorhombic phases are obtained and confirmed by x-ray diffractometer ( XRD) results. X-ray photoelectron spectroscopy ( XPS) analysis shows that chemical composition of all the films is stoichiometry. It is found that the amorphous Ta2O5 film achieves the highest laser induced damage threshold ( LIDT) either at 355 or 1064 nm, followed by hexagonal phase and finally orthorhombic phase. The damage morphologies at 355 and 1064 nm are different as the former shows a uniform fused area while the latter is centred on one or more defect points, which is induced by different damage mechanisms. The decrease of the LIDT at 1064nm is attributed to the increasing structural defect, while at 355nm is due to the combination effect of the increasing structural defect and decreasing band gap energy.

355nm增透膜的设计、制备与性能

用热舟蒸发法结合修正挡板技术制备了355 nm LaF3/MgF2增透膜,并对部分样品进行了真空退火。采用Lambda 900光谱仪测试了增透膜的低反光谱和透射光谱,并考察了其光谱稳定性;使用脉冲8 ns的355 nm激光测试了增透膜的激光损伤阈值(LIDT);采用Normarski显微镜对增透膜的表面缺陷密度和破斑形貌进行了观察。实验结果表明,制备得到的增透膜的剩余反射率较低,光谱稳定性好;真空退火对增透膜的激光损伤阈值没有改善;增透膜的破环形貌为散点形式,结合破斑深度测试表明薄膜的破坏源于薄膜和基底界面的缺陷点。JGS1熔石英基底由于有好的表面状况、固有的高激光损伤阈值和以其为基底的增透膜具有更低的表面场强,使得其上的增透膜有更高的抗激光损伤能力。

HfO2的纯度对紫外多层膜反射率的影响

用辉光放电质谱法和二次离子质谱仪测定了两种HfO2材料及它们相应的单层膜中的杂质含量，结果发现，无论是在体材料中还是在用电子束蒸发技术沉积的材料单层薄膜中，ZrO2都是这两种HfO2材料中最主要的杂质。而且，这两种HfO2材料中Zr含量的差别远远大于Ti、Fe含量的差别，这说明Zr含量的差别正是引起两种HfO2膜层光学性能差别的原因。用这两种不同纯度的HfO2材料与同一纯度的SiO2材料组合，沉积形成266nm的紫外反射镜，实验结果表明这两种反射镜的反射率分别在99.85% 和 99.15%左右。这个结果与依据单层膜得出的光学常数所设计的结果符合的很好。

Investigation on thermal stability of TiO2 films for application at high temperature

The thermal stability of electron beam deposited TiO2 monolayers and TiO2/SiO2 high reflectors (HR) during 300 to 1100 degrees C annealing is studied. It is found that the optical loss of film increases with the increase in annealing temperature, due to the phase change, crystallisation and deoxidising of film. Scattering loss dominates the optical property degradation of film below 900 degrees C, while the absorption is another factor at 1100 degrees C. The increase in refractive index and decrease in physical thickness of TiO2 layer shift the spectra of HR above 900 degrees C. The possible crack mechanism on the surface of HR during annealing is discussed. Guidance for application on high temperature stable optical coatings is given.

High refractive index TiO2 film deposited by electron beam evaporation

The well known 'crystal seed' theory is first applied in this work to prepare TiO2 film: a high refractive index rutile TiO2 film is grown by electron beam evaporation on the rutile seed formed by 1100 degrees C annealing. The average n is larger than 2.4, by far the highest in all the authors' TiO2 films. The films are characterised by optical properties, microstructure and surface morphologies. It is found that the refractive index shows positive relation with the crystal structure, grain size, and packing density and roughness of the film. The film has lower density of granularity and nodule defects on the surface than those of the film deposited by magnetron sputtering. The result shows attractive application in complex filter and laser coatings.

Occupational exposure to nano-TiO2 in the life cycle steps of new depollutant mortars used in construction

The present work is focused on the measurement of workers exposure to nano-TiO2 in the life cycle steps of depollutant mortars. It has been done in the framework of the SCAFFOLD project, which aims at the management of potential risks arising from the use of manufactured nanomaterials in construction. Main findings can be summarized as follows: (1) The occupational exposure to nano-TiO2 is below 0.3 mg/m(3) for all measured scenarios. The highest concentrations were measured during the cleaning task (in the nano-TiO2 manufacturing process) and during the application (spraying) of depollutant coatings on a wall. (2) It was found a high release of particles above the background in several tasks as expected due to the nature of the activities performed. The maximum concentration was measured during drilling and during adding powder materials (mean total particle concentration up to 5.591E+04 particles/cm(3) and 5.69E+04 particles/cm(3)). However, considering data on total particle concentration released, no striking differences have been observed when tasks have been performed using conventional materials in the sector (control) and when using materials doped with nano-objects.

Eletrodeposição de ligas Zn-Co por corrente contínua e pulsada simples, a partir de banhos ambientalmente não agressivos

Revestimentos produzidos a partir de ligas de Zn-Co são comumente utilizados em indústrias (aeronáutica, de isoladores elétricos e automobilística, por exemplo) devido à sua ótima resistência à corrosão, principalmente quando comparados aos tradicionais revestimentos de Zn puro. Na co-deposição de zinco com metais, como o ferro, cobalto e níquel, ocorre o que se chama de deposição anômala, onde o metal menos nobre (zinco) é preferencialmente depositado, independente do modo de corrente aplicada (contínua ou pulsada). Recentemente, diversos trabalhos relacionam a produção de eletrodepósitos de liga Zn-Co a partir de banhos ambientalmente não agressivos, a fim de substituir os banhos alcalinos extremamente tóxicos, a base de cianeto. Na presente dissertação foram produzidos revestimentos de ligas de Zn-Co sobre substrato de aço carbono, empregando corrente contínua ou corrente pulsada simples, a partir de banhos contendo diferentes concentrações de Co2+ (0,05 mol/L e 0,10mol/L), 0,05 mol/l de Zn2+ e citrato de sódio (0,10 mol/L) como agente complexante, sob condições agitadas. Quatro diferentes valores de densidade de corrente (10 A/m2, 20 A/m2, 40 A/m2 e 80 A/m2) e de frequência de pulso (100 Hz, 500 Hz, 1000 Hz, 2000 Hz) foram aplicados para a produção da liga a partir dos dois banhos, tendo como objetivo avaliar a influência dos parâmetros de deposição(concentração de Co (II), densidade de corrente aplicada e, no caso de deposição por corrente pulsada simples, também da frequência de pulso), nas variáveis eficiência de corrente catódica, composição da liga, densidade de corrente de corrosão, microestrutura e morfologia dos depósitos de liga Zn-Co. As cores das camadas obtidas variaram do cinza claro ao escuro, quase sempre sem brilho, independente do modo de corrente empregado. Foi verificado que o processo normal de eletrodeposição foi prevalente na produção de revestimentos por corrente contínua, enquanto que apenas deposição anômala foi observada quando do uso de corrente pulsada. A maior eficiência de corrente catódica (60%) foi obtida, para corrente contínua, nas condições de menor concentração de Co2+ (0,05 mol/L) e maior densidade de corrente (80 A/m2). Nestas mesmas condições foi determinada uma eficiência de corrente catódica de 98% para corrente pulsada simples na freqüência de 2000 Hz. Maiores teores do metal mais nobre (cobalto) foram alcançados em maiores densidades de corrente para todas as condições empregadas. Os revestimentos assim obtidos apresentavam os menores valores de tamanho de grão, para cada uma das soluções estudadas. Os demais parâmetros estudados também influenciaram na granulometria e na morfologia das ligas obtidas. Revestimentos com melhor resistência à corrosão, contendo teores de cobalto entre aproximadamente 8 e 10% m/m, foram produzidos a partir do banho com maior concentração de Co2+, sob corrente pulsada simples

Modelling the entrainment and motion of particles in a gap: Application to abrasive wear

The microscale abrasion or ball-cratering test is being increasingly applied to a wide range of bulk materials and coatings. The response of materials to this test depends critically on the nature of the motion of the abrasive particles in the contact zone: whether they roll and produce multiple indentations in the coating, or slide causing grooving abrasion. Similar phenomena also occur when hard contaminant particles enter a lubricated contact. This paper presents simple quantitative two-dimensional models which describe two aspects of the interaction between a hard abrasive particle and two sliding surfaces. The first model treats the conditions under which a spherical abrasive particle of size d can be entrained into the gap between a rotating sphere of radius R and a plane surface. These conditions are determined by the coefficients of friction between the particle and the sphere, and the particle and the plane, denoted by μs and μp respectively. This model predicts that the values of (μs + μp) and 2μs should both exceed √2d/R for the particles to be entrained into the contact. If either is less than this value, the particle will slide against the sphere and never enter the contact. The second model describes the mechanisms of abrasive wear in a contact when an idealized rhombus-sectioned prismatic particle is located between two parallel plane surfaces separated by a certain distance, which can represent either the thickness of a fluid film or the spacing due to the presence of other particles. It is shown that both the ratio of particle size to the separation of the surfaces and the ratio of the hardnesses of the two surfaces have important influences on the particle motion and hence on the mechanism of the resulting abrasive wear. Results from this model are compared with experimental observations, and the model is shown to lead to realistic predictions. © IMechE 2003.