Getting value out of your sensory testing - the difference from control test

Non-parametric difference tests such as triangle and duo-trio tests traditionally are used to establish differences or similarities between products. However they only supply the researcher with partial answers and often further testing is required to establish the nature, size and direction of differences. This paper looks at the advantages of the difference from control (DFC) test (also known as degree of difference test) and discusses appropriate applications of the test. The scope and principle of the test, panel composition and analysis of results are presented with the aid of suitable examples. Two of the major uses of the DFC test are in quality control and shelf-life testing. The role DFC takes in these areas and the use of other tests to complement the testing is discussed. Controls or standards are important in both these areas and the use of standard products, mental and written standards and blind controls are highlighted. The DFC test has applications in products where the duo-trio and triangle tests cannot be used because of the normal heterogeneity of the product. While the DFC test is a simple difference test it can be structured to give the researcher more valuable data and scope to make informed decisions about their product.

Morphological transitions in polymer monolayers under compression

We present a systematic investigation of morphological transitions in poly vinylacetate Langmuir monolayers. On compression, the polymer monolayer is converted to a continuous membrane with a thickness of similar to 2-3 nm. Above a certain surface concentration the monolayer, on water, undergoes a morphological transition-buckling, leading to formation of striped patterns of period of lambda(b)similar to 160 nm, as determined from in situ grazing incidence small angle x-ray scattering measurements. The obtained value is much smaller than what has been typically observed for Langmuir monolayers on water or thin films on soft substrates. Using existing theories for buckling of fluidlike films on fluid substrates, we obtain very low values of bending rigidity and Young's modulus of the polymer monolayer compared to that observed earlier for lipid or polymeric monolayers. Since buckling in these monolayers occurs only above a certain surface concentration, we have looked at the possibility that the buckling in these films occurs due to changes in their mechanical properties under compression. Using the model of Huang and Suo of buckling of solidlike films on viscoelastic substrates, we find values of the mechanical properties, which are much closer to the bulk values but still significantly lower. Although the reduction could be along the lines of what has been observed earlier for ultrathin polymer film or surface layers of polymers, the possibility of micromechanical effects also determining the buckling in such polymer monolayers cannot be ruled out. We have provided possible explanation of the buckling of the poly vinylacetate monolayers in terms of the change in isothermal compression modulus with surface concentration.

Mango anthracnose disease: Present status and future research priorities

Occurrence and Importance: Anthracnose is presently recognized as the most important field and post-harvest disease of mango worldwide (Ploetz and Prakasli, 1997). It is the major disease limiting fruit production in all countries where mangoes are grown, especially where high humidity prevails during the cropping season. The post-harvest phase is the most damaging and economically significant phase of the disease worldwide. It directly affects the marketable fruit rendering it worthless. This phase is directly linked to the field phase where initial infection usually starts on young twigs and leaves and spreads to the flowers, causing blossom blight and destroying the inflorescences and even preventing fruit set.

The risk of pollen-mediated gene flow from exotic Corymbia plantations into native Corymbia populations in Australia

Sectors of the forest plantation industry in Australia are set to expand in the near future using species or hybrids of the spotted gums (Corymbia, Section Politaria). Plantations of these taxa have already been introduced across temperate and subtropical Australia, representing locally exotic introductions from native stands in Queensland and New South Wales. A literature review was undertaken to provide insights into the potential for pollen-mediated gene flow from these plantations into native populations. Three factors suggest that such gene flow is likely; (1) interspecific hybridisation within the genus has frequently been recorded, including between distantly related species from different sections, (2) apparent high levels of vertebrate pollinator activity may result in plantation pollen being moved over hundreds of kilometres, (3) much of the plantation estate is being established among closely related taxa and therefore few barriers to gene flow are expected. Across Australia, 20 of the 100 native Corymbia taxa were found to have regional level co-occurrence with plantations. These were located most notably within regions of north-east New South Wales and south-east Queensland, however, co-occurrence was also found in south-west Western Australia and eastern Victoria. The native species found to have co-occurrence were then assessed for the presence of reproductive barriers at each step in the process of gene flow that may reduce the number of species at risk even further. The available data suggest three risk categories exist for Corymbia. The highest risk was for gene flow from plantations of spotted gums to native populations of spotted gums. This was based on the expected limited existence of pre- and post-zygotic barriers, substantial long-distance pollen dispersal and an apparent broad period of flowering in Corymbia citriodora subsp. variegata plantations. The following risk category focussed on gene flow from Corymbia torelliana × C. c. variegata hybrid plantations into native C. c. variegata, as the barriers associated with the production and establishment of F1 hybrids have been circumvented. For the lowest risk category, Corymbia plantations may present a risk to other non-spotted gum species, however, further investigation of the particular cross-combinations is required. A list of research directions is provided to better quantify these risks. Empirical data will need to be combined within a risk assessment framework that will not only estimate the likelihood of exotic gene flow, but also consider the conservation status/value of the native populations. In addition, the potential impacts of pollen flow from plantations will need to be weighed up against their various economic and environmental benefits.

Predicting wood value in Queensland Caribbean pine plantations using a decision support system

A decision support system has been developed in Queensland to evaluate how changes in silvicultural regimes affect wood quality, and specifically the graded recovery of structural timber. Models of tree growth, branch architecture and wood properties were developed from data collected in routine Caribbean pine plantations and specific silvicultural experiments. These models were incorporated in software that simulates the conversion of standing trees into logs, and the logs into boards, and generates detailed data on knot location and basic density distribution. The structural grade of each board was determined by simulating the machine stress-grading process, and the predicted graded recovery provided an indicator of wood value. The decision support system improves the basis of decision-making by simulating the performance of elite genetic material under specified silvicultural regimes and by predicting links between wood quality and general stand attributes such as stocking and length of rotation.

Double-Edged Imitation : Theories and Practices of Pastiche in Literature

This study concentrates on the contested concept of pastiche in literary studies. It offers the first detailed examination of the history of the concept from its origins in the seventeenth century to the present, showing how pastiche emerged as a critical concept in interaction with the emerging conception of authorial originality and the copyright laws protecting it. One of the key results of this investigation is the contextualisation of the postmodern debate on pastiche. Even though postmodern critics often emphasise the radical novelty of pastiche, they in fact resuscitate older positions and arguments without necessarily reflecting on their historical conditions. This historical background is then used to analyse the distinction between the primarily French conception of pastiche as the imitation of style and the postmodern notion of it as the compilation of different elements. The latter s vagueness and inclusiveness detracts from its value as a critical concept. The study thus concentrates on the notion of stylistic pastiche, challenging the widespread prejudice that it is merely an indication of lack of talent. Because it is multiply based on repetition, pastiche is in fact a highly ambiguous or double-edged practice that calls into question the distinction between repetition and original, thereby undermining the received notion of individual unique authorship as a fundamental aesthetic value. Pastiche does not, however, constitute a radical upheaval of the basic assumptions on which the present institution of literature relies, since, in order to mark its difference, pastiche always refers to a source outside itself against which its difference is measured. Finally, the theoretical analysis of pastiche is applied to literary works. The pastiches written by Marcel Proust demonstrate how it can become an integral part of a writer s poetics: imitation of style is shown to provide Proust with a way of exploring the role of style as a connecting point between inner vision and reality. The pastiches of the Sherlock Holmes stories by Michael Dibdin, Nicholas Meyer and the duo Adrian Conan Doyle and John Dickson Carr illustrate the functions of pastiche within a genre detective fiction that is itself fundamentally repetitive. A.S. Byatt s Possession and D.M. Thomas s Charlotte use Victorian pastiches to investigate the conditions of literary creation in the age of postmodern suspicion of creativity and individuality. The study thus argues that the concept of pastiche has valuable insights to offer to literary criticism and theory, and that literary pastiches, though often dismissed in reviews and criticism, are a particularly interesting object of study precisely because of their characteristic ambiguity.

On the leakage resilience of secure channel establishment

Secure communication channels are typically constructed from an authenticated key exchange (AKE) protocol, which authenticates the communicating parties and establishes shared secret keys, and a secure data transmission layer, which uses the secret keys to encrypt data. We address the partial leakage of communicating parties' long-term secret keys due to various side-channel attacks, and the partial leakage of plaintext due to data compression. Both issues can negatively affect the security of channel establishment and data transmission. In this work, we advance the modelling of security for AKE protocols by considering more granular partial leakage of parties' long-term secrets. We present generic and concrete constructions of two-pass leakage-resilient key exchange protocols that are secure in the proposed security models. We also examine two techniques--heuristic separation of secrets and fixed-dictionary compression--for enabling compression while protecting high-value secrets.

Time dependence of effective slip on textured hydrophobic surfaces

In this paper, we present results on water flow past randomly textured hydrophobic surfaces with relatively large surface features of the order of 50 µm. Direct shear stress measurements are made on these surfaces in a channel configuration. The measurements indicate that the flow rates required to maintain a shear stress value vary substantially with water immersion time. At small times after filling the channel with water, the flow rates are up to 30% higher compared with the reference hydrophilic surface. With time, the flow rate gradually decreases and in a few hours reaches a value that is nearly the same as the hydrophilic case. Calculations of the effective slip lengths indicate that it varies from about 50 µm at small times to nearly zero or “no slip” after a few hours. Large effective slip lengths on such hydrophobic surfaces are known to be caused by trapped air pockets in the crevices of the surface. In order to understand the time dependent effective slip length, direct visualization of trapped air pockets is made in stationary water using the principle of total internal reflection of light at the water-air interface of the air pockets. These visualizations indicate that the number of bright spots corresponding to the air pockets decreases with time. This type of gradual disappearance of the trapped air pockets is possibly the reason for the decrease in effective slip length with time in the flow experiments. From the practical point of usage of such surfaces to reduce pressure drop, say, in microchannels, this time scale of the order of 1 h for the reduction in slip length would be very crucial. It would ultimately decide the time over which the surface can usefully provide pressure drop reductions. ©2009 American Institute of Physics

Olla elävän sanat : Roolirunon laji Maila Pylkkösen teoksessa Arvo. Vanhaäiti puhuu runonsa

Maila Pylkkönen (1931 1986) was one of the most important modernist poets in Finland and a central figure in developing the dramatic monologue in Finnish literature. The study examines Pylkkönen s poetic work Arvo. Vanhaäiti puhuu runonsa (Value. An old woman speaks her poem, 1959) as an example of the dramatic monologue, approaching it from three perspectives: its generic features and background, and the poetic framework to which it connects in the context of Pylkkönen s poetry. In addition to methods of literary scholarship, the poetic analysis benefits from a linguistic approach. The study shows that the dramatic monologue genre drives Pylkkönen s first work, Klassilliset tunteet (Classical feelings, 1957), in a context of finding poetic identity, characterised by the expression to be the words of a living creature . The study demonstrates that important generic features of the dramatic monologue, namely, a poem representing a speech-event and a hierarchical structure, are also Arvo s most significant generic features. Arvo s poems as speech-events are examined for their internal progressive, pragmatic unity constructed through single line units; for their function as narratives dealing with the life story of an old woman, Arvo s speaker; and from the perspective of the communication between the old woman and the poems other characters. Arvo s speech-events can also be seen as semantic shifts from one poem to another: the poems construct semantic stages representing different phases of the old woman s life. The study demonstrates that analysis of Arvo s hierarchical structure, that is, the relationship between the speaker and the rhetorical levels, reveals the work s structural and ideological wholeness by focusing on the old woman s emotions: longing, loneliness and alienation from the world. In other words, the contradictions between the explicit level of the speaker and an implied rhetorical level open up the tragedy of an old woman s daily life. Study of Arvo s hierarchical structure also highlights the special position of the reader in the framework of a dramatic monologue. The elements of a dramatic present in which the old woman s emotions are conveyed, an italicized opening poem, and the work s title Value invite the reader to consider Arvo as a structural and ideological whole. The function of Arvo s hierarchical structure is to ask the reader to recognise the hopelessness of the old woman s situation, understand it, and even identify with it.

Improving knowledge and practices in fresh produce chains

A successful supply chain must delivery the right product, value and satisfaction to the end customer, and profitability for its participants. Critical to getting the product right is the practices used to produce and maintain product quality through the supply chain from production to sale to the end customer. This paper describes the approach used by a R&D team to add value to supply chains through improving knowledge and practices. The desired outcome is better produce quality for consumers and more control and less wastage for chain participants. The team worked with specific supply chains to identify areas for improvement and to develop, test and implement improved practices. The knowledge gained was communicated to the industry to gain wider adoption of results. Three conditions were identified as critical for practice change - motivation, knowledge, and capacity for change. For improvement in practices to occur, a business must be motivated and have the knowledge and capacity to improve. Two case studies of working with Australian supply chains (mango and melons) are presented to illustrate our participatory methodology. A key activity is monitoring produce quality and handling practices and conditions to demonstrate to participants the points where quality deterioration occurs in the supply chain. This participatory approach is successful because working with supply chain participants generates knowledge and solutions to real problems. It enables the participants to observe the effect of handling practices and conditions on produce quality, gain knowledge and assess the benefits of improvements. Where existing knowledge is not present, research is conducted to fill the knowledge gaps. IV International Conference on Managing Quality in Chains - The Integrated View on Fruits and Vegetables Quality

Oxygen transfer in circular surface aeration tanks

Surface aeration systems employed in activated sludge plants are the most energy-intensive units of the plants and typically account for a higher percentage of the treatment facility's total energy use. The geometry of the aeration tank imparts a major effect on the system efficiency. It is said that at optimal geometric onditions, systems exhibits the maximum efficiency. Thus the quantification of the optimal geometric conditions in surface aeration tanks is needed. Optimal geometric conditions are also needed to scale up the laboratory result to the field installation. In the present work, experimental studies have been carried out on baffled and unbaffled circular surface aeration tanks to ascertain the optimal geometric conditions. It is found that no optimal geometric conditions exist for the liquid/water depth in circular surface aeration tanks; however, for design purposes, a standard value has been assumed. Based on the optimal geometric conditions, a scale-up equation has been developed for the baffled circular surface aeration tanks.

Spatial patterns of sub-tidal seagrasses and their tissue nutrients in the Torres Strait, northern Australia: Implications for management

The distribution and nutritional profiles of sub-tidal seagrasses from the Torres Strait were surveyed and mapped across an area of 31,000 km2. Benthic sediment composition, water depth, seagrass species type and nutrients were sampled at 168 points selected in a stratified representative pattern. Eleven species of seagrass were present at 56 (33.3%) of the sample points. Halophila spinulosa, Halophila ovalis, Cymodocea serrulata and Syringodium isoetifolium were the most common species and these were nutrient profiled. Sub-tidal seagrass distribution (and associated seagrass nutrient concentrations) was generally confined to northern-central and south-western regions of the survey area (value. This spatial and nutritional information can be used by local agencies to manage and to protect the ecological, economic and cultural values of the sub-tidal seagrass ecosystems and associated fisheries of the Torres Strait.

Cultivar affects browning susceptibility of freshly cut star fruit slices

Consumption of freshly-cut horticultural products has increased in the last few years. The principal restraint to using freshly-cut carambola is its susceptibility to tissue-browning, due to polyphenol oxidase-mediated oxidation of phenolic compounds present in the tissue. The current study investigated the susceptibility to browning of star fruit slices (Averrhoa carambola L.) of seven genotypes (Hart, Golden Star, Taen-ma, Nota-10, Malasia, Arkin, and Fwang Tung). Cultivar susceptibility to browning as measured by luminosity (L*) varied significantly among genotypes. Without catechol 0.05 M, little changes occurred on cut surface of any cultivars during 6 hour at 25 degrees C, 67% RH. Addition of catechol led to rapid browning, which was more intense in cvs. Taen-ma, Fwang Tung, and Golden Star, with reduction in L* value of 28.60%, 27.68%, and 23.29%, respectively. Browning was more intense in the center of the slices, particularly when treated with catechol, indicating highest polyphenol oxidase (PPO) concentration. Epidermal browning, even in absence of catechol, is a limitation to visual acceptability and indicates a necessity for its control during carambola processing. Care must be given to appropriate selection of cultivars for fresh-cut processing, since cultivar varied in browning susceptibility in the presence of catechol.

An overview of integrated pest management (IPM) in north-eastern Australian grain farming systems: Past, present and future prospects

The authors overview integrated pest management (IPM) in grain crops in north-eastern Australia, which is defined as the area north of latitude 32°S. Major grain crops in this region include the coarse grains (winter and summer cereals), oilseeds and pulses. IPM in these systems is complicated by the diversity of crops, pests, market requirements and cropping environments. In general, the pulse crops are at greatest risk, followed by oilseeds and then by cereal grains. Insecticides remain a key grain pest management tool in north-eastern Australia. IPM in grain crops has benefited considerably through the increased adoption of new, more selective insecticides and biopesticides for many caterpillar pests, in particular Helicoverpa spp. and loopers, and the identification of pest-crop scenarios where spraying is unnecessary (e.g. for most Creontiades spp. populations in soybeans). This has favoured the conservation of natural enemies in north-eastern Australia grain crops, and has arguably assisted in the management of silverleaf whitefly in soybeans in coastal Queensland. However, control of sucking pests and podborers such as Maruca vitrata remains a major challenge for IPM in summer pulses. Because these crops have very low pest-damage tolerances and thresholds, intervention with disruptive insecticides is frequently required, particularly during podfill. The threat posed by silverleaf whitefly demands ongoing multi-pest IPM research, development and extension as this pest can flare under favourable seasonal conditions, especially where disruptive insecticides are used injudiciously. The strong links between researchers and industry have facilitated the adoption of IPM practices in north-eastern Australia and augers well for future pest challenges and for the development and promotion of new and improved IPM tactics.

Specimen-based databases of Australian plant pathogens: past, present and future

Specimen-based records of most of the plant pathogens that occur in Australia can be accessed through the Australian Plant Disease Database and the Australian Plant Pest Database. These databases and the herbaria that underpin them are important resources for resolving quarantine and trade issues as well as for the diagnosis of plant diseases. The importance of these collections and databases to Australia's agricultural industries is discussed.