Impactos do estresse salino e da cobertura morta nas características químicas do solo e no desenvolvimento do amaranto

Availability of good quality water has been reduced vertiginously, over the last decade, in the world. In some regions, the water resources have high concentration of the dissolved salts, these characteristics of the water make it s use impossible. Water quality can be a limitation for irrigated agriculture, principally in regions of arid or semiarid climate where the water resources are generally saline and are exposed at high evaporation ratio. For that reason, precipitation of the salts occurs near the soil surface and those salts themselves cumulate in the vegetal tissue, reducing the soil fertility and crop production. The adoption of tolerant crop to the water salinity and soil salinity, adaptable to the climatic conditions is other emergent necessity. This work had the goal of studying the effects of four salinity levels of the irrigation water salinity and use of mulch, dried leaves of Forest mangrove (Acacia mangiumWilld), in cultivated soil with amaranth (Amaranthus cruentus, BRS Alegria variety), in greenhouse. It was utilized the transplant of plants to PVC columns, containing 30 kg of silty loam soil, 10 days after emerging, with space of 50 x 50 cm between lines. Treatments were composed by combination of four levels of salinity (0.147; 1.500; 3.000 e 4.500 dS m-1), obtained by addition NaCl (commercial) to irrigation water and soil with and without protection, by mulch. A factorial system 4 x 2 was used with four repetitions, totalizing 32 parcels. The concentrations of nutrients in soil solution have been evaluated, in the dry matter of the vegetal tissue (roots, stem, leaves and raceme residue), at the end of the vegetative cycle. The use of soil protection reduced time for the beginning inflorescence of plants, at the same time, the increase of the salinity delayed this phase of amaranth development. The use of the mulch effectively increased the height, stem diameter, area of the larger leaf, humidity and dry matter content and amaranth grain production. The vegetal species showed salinity tolerance to experimented levels. The adopted treatments did not affect the pH values, exchangeable cation contents, electrical conductivity of soil solution (EC1:5) and saturated extract (ECSE), and Ca+2, Mg+, Fe+2 and Mn+2 contents, in the soil solution. The increase of the salinity concentration in the irrigation water inhibited the mineralization process of the organic matter (OM) and, consequently, the efficiency in the it´s utilization by plants, at the same time, produced increase in the values of the exchangeable sodium percentage (ESP), sodium adsorption ratio (SAR) and potassium adsorption ratio (PAR), in the soil solution. Therefore, the use of the mulch did not affect the first three parameters. The protein and nutrient contents: K+, Ca+2, P, Mg+2 e Cu+2, in amaranth grains, were improved by tillage condition. The raceme residues showed chemical/nutritional composition that makes advantageous its application in animal ration. In this context, it follows that amaranth tolerate the saline stress, of the irrigation water, until 4.500 dS m-1, temperature and relative humidity of the air predominant in the experimental environment

Desenvolvimento de um secador spray para obtenção de pós finos de precursores de nióbio

This work presents a spray-dryer designed to oxalate-niobate precursors and suitable for the production of Niobium Carbide. The dryer was intended to produce powders of controlled particle size. First, the precursor is dissolved in water to produce a solution of known concentration and then it is atomized on the spray-dryer to produce the powder. This equipment consists of a 304 stainless steel chamber, 0.48 m x 1.9 m (diameter x length), with a conical shape at the lower portion, which is assembled on a vertical platform. The chamber is heated by three 4 kW electrical resistances. In this process, drying air is heated as it flows inside a serpentine surrounding the chamber, in contrary to more traditional processes in which the hot drying air is used to heat the component. The air enters the chamber at the same temperature of the chamber, thus avoiding adherence of particles on the internal surface. The low speed flow is concurrent, directed from the top to the bottom portion of the chamber. Powders are deposited on a 0.4 m diameter tray, which separates the cylindrical portion from the conical portion of the chamber. The humid air is discharged though a plug placed underneath the collecting tray. A factorial experimental planning was prepared to study the influence of five parameters (concentration, input flow, operation temperature, drying air flow and spray air flow) on the characteristics of the powders produced. Particle size distribution and shape were measured by laser granulometry and scanning electronic microscopy. Then, the powders are submitted to reaction in a CH4 / H2 atmosphere to compare the characteristics of spray-dried powders with powders synthetizided by conventional methods

Crescimento aéreo e radicular da soja e de plantas de cobertura em camadas compactadas de solo

O cultivo de plantas de cobertura com sistema radicular vigoroso em rotação de culturas pode melhorar a qualidade física de solos compactados. O objetivo deste trabalho foi avaliar o crescimento aéreo e radicular da soja e de cinco espécies utilizadas como plantas de cobertura de verão (guandu, guandu anão, mucuna preta, labe labe e crotalária juncea), em solo submetido a três níveis de compactação em subsuperfíce. Utilizou-se um Nitossolo Vermelho argiloso em vasos montados com anéis de PVC sobrepostos, com diâmetro interno de 20 cm e altura de 50 cm. A camada compactada localizada de 20-30 cm de profundidade foi caracterizada pelas densidades do solo de 1,13, 1,34 e 1,56 g cm-3 e 0,26, 0,66 e 1,98 MPa de impedância mecânica, respectivamente. Aos 60 dias da emergência das plantas, determinaram-se as massas da matéria seca da parte aérea e das raízes, a densidade do comprimento radicular e o diâmetro médio radicular. Apesar de alterar a distribuição do sistema radicular ao longo do perfil do solo, o impedimento físico em subsuperfície não diminuiu a produção total de raízes da soja e dos adubos verdes, com exceção da crotalária juncea. A mucuna preta foi a leguminosa mais tolerante e a soja a mais sensível à compactação do solo. O sistema radicular da crotalária juncea apresentou potencial de formação de bioporos compatível ao da mucuna preta, apesar de ter sido relativamente mais sensível à compactação do solo. O diâmetro médio das raízes da soja e da crotalária juncea apresentou correlação significativa com o crescimento radicular dentro da camada de solo compactado.

Utilização de métodos estatísticos multivariados na caracterização do mosaico sucessional em floresta semidecídual

O presente trabalho objetivou verificar a possibilidade da utilização de métodos estatísticos multivariados na caracterização das fases do desenvolvimento do mosaico sucessional de um trecho de floresta estacional semidecidual, através de variáveis estruturais. Foram alocadas parcelas de 10 m x 10 m, em que se procedeu à análise estrutural, ou seja, levantamento fitossociológico acrescido das variáveis Porcentagem de Cobertura (PC), Altura do Dossel (AD) e Cobertura por Lianas (CL). Os métodos estatísticos empregados foram Análise de Componentes Principais e Análise de Agrupamento, mais especificamente Classificação Hierárquica Ascendente. O primeiro componente principal explicou 43,96% da variância total, enquanto o segundo, 25,66%. As variáveis Área Basal (AB), Diâmetro Médio (DM) e Dominância Média (DOM) apresentaram correlações positivas entre si superiores a 0,75, podendo ser DM e DOM consideradas como um grupo de variáveis. As variáveis Número de Indivíduos (NI) e Número de Espécies (NE) apresentaram correlação 0,60, enquanto AD, CL e PC baixas correlações com as demais, indicando a importância da inclusão destas na análise. A classificação hierárquica e a partição dos grupos em quatro foram feitas considerando os dois primeiros eixos fatoriais. Os resultados indicaram dois comportamentos diferenciados: 1) valores baixos para AD e AB: Grupo 1, com valores baixos também para NI, NE e PC (fase de clareira); e Grupo 2, com valores elevados para NI e CL e baixos para DOM e DM (fase de construção); e 2) valores altos para AD e AB: Grupo 3, com valores altos também para NI, NE e PC e valor baixo para CL (fase madura); e Grupo 4, com valores elevados para DOM e DM e mais baixos para CL (fase de degradação). Os métodos estatísticos multivariados permitiram caracterizar as fases do desenvolvimento do mosaico sucessional, através das variáveis estruturais. A forma como foram estimadas as variáveis AD, CL e PC, porém, deve ser aprimorada, assim como é preciso incluir variáveis que discriminem melhor cada fase.

Desenvolvimento de plantas de crisântemo cultivadas em vaso em resposta a níveis de condutividade elétrica

Na floricultura, a competição por mercados é intensa e o diferencial de produtividade consiste no manejo nutricional adequado, por promover grande impacto sobre a qualidade, a produtividade e a longevidade das inflorescências e da planta. O presente trabalho teve o objetivo de avaliar os efeitos de níveis de condutividade elétrica (CE) no desenvolvimento de plantas de crisântemo (Dendranthema grandiflora Tzvelev.) em vaso sob cultivo protegido. O experimento foi conduzido no município de Paranapanema - SP. Usou-se o delineamento experimental de blocos casualizados com quatro repetições e parcelas divididas. As parcelas foram constituídas pelas épocas de amostragem, e as subparcelas, pelos diferentes níveis de CE, determinados na solução aplicada via água de irrigação: 1,42; 1,65; 1,89; 2,13 e 2,36 dS m-1 (fase vegetativa); 1,71; 1,97; 2,28; 2,57 e 2,85 dS m-1 (fase de botão). Determinaram-se, semanalmente, a altura da planta e o diâmetro do buquê, e a cada 14 dias, a área foliar e a fitomassa seca da parte aérea da planta. O tratamento, correspondente à aplicação de solução com CE de 2,13 dS m-1 na fase vegetativa e 2,57 dS m-1 na fase de botão, proporcionou melhor aspecto visual das plantas, além de apresentar maior valor de fitomassa seca da parte aérea, maior área foliar e melhores formação e coloração.

Recuperação e purificação de proteínas do soro de queijo tipo coalho usando cromatografia de troca iônica e interação hidrofóbica em leito na forma expandida

Expanded Bed Adsorption plays an important role in the downstream processing mainly for reducing costs as well as steps besides could handling cells homogenates or fermentation broth. In this work Expanded Bed Adsorption was used to recover and purify whey proteins from coalho cheese manufacture using Streamline DEAE and Streamline SP both ionic resins as well as a hydrophobic resin Streamline Phenyl. A column of 2.6 cm inner diameter with 30 cm in height was coupled to a peristaltic pump. Hydrodynamics study was carried out with the three resins using Tris-HCl buffer in concentration of 30, 50 and 70 mM, with pH ranging from 7.0 to 8.0. In this case, assays of the expansion degree as well as Residence Time Distribution (RTD) were carried out. For the recovery and purification steps, a whey sample of 200 mL, was submitted to a column with 25mL of resin previously equilibrated with Tris/HCl (50 mM, pH 7.0) using a expanded bed. After washing, elution was carried out according the technique used. For ionic adsorption elution was carried out using 100 mL of Tris/HCl (50 mM, pH 7.0 in 1M NaCl). For Hydrophobyc interaction elution was carried out using Tris/HCl (50 mM, pH 7.0). Adsorption runs were carried out using the three resins as well as theirs combination. Results showed that for hydrodynamics studies a linear fit was observed for the three resins with a correlation coefficient (R2) about 0.9. In this case, Streamline Phenyl showed highest expansion degree reaching an expansion degree (H0/H) of 2.2. Bed porosity was of 0.7 when both resins Streamline DEAE and Streamline SP were used with StremLine Phenyl showing the highest bed porosity about 0.75. The number of theorical plates were 109, 41.5 and 17.8 and the axial dipersion coefficient (Daxial) were 0.5, 1.4 and 3.7 x 10-6 m2/s, for Streamline DEAE, Streamline SP and Streamline Phenyl, respectively. Whey proteins were adsorved fastly for the three resins with equilibrium reached in 10 minutes. Breakthrough curves showed that most of proteins stays in flowthrough as well as washing steps with 84, 77 and 96%, for Streamline DEAE, Streamline SP and Streamline Phenyl, respectively. It was observed protein peaks during elution for the three resins used. According to these peaks were identified 6 protein bands that could probably be albumin (69 KDa), lactoferrin (76 KDa), lactoperoxidase (89 KDa), β-lactoglobulin (18,3 KDa) e α-lactoalbumin (14 KDa), as well as the dimer of beta-lactoglobulin. The combined system compound for the elution of Streamline DEAE applied to the Streamline SP showed the best purification of whey proteins, mainly of the α-lactoalbumina

Anatomia comparada do lenho de Copaifera langsdorffii Desf. (Leguminosae-Caesalpinoideae) de floresta e cerradão

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Exportação de nutrientes e qualidade de cultivares de rosas em campo e em ambiente protegido

Foram avaliadas a exportação de nutrientes por cultivares de rosas e as características que refletem qualidade em campo e ambiente protegido. O delineamento experimental foi inteiramente casualizado, sendo os tratamentos constituídos por 15 e 12 cvs. em ambiente protegido e em campo, respectivamente, com três repetições. Cada unidade experimental foi constituída por duas plantas, sendo coletada uma haste por planta. Foram determinados o diâmetro da haste e do botão floral, comprimento da haste, fitomassa seca e acúmulo de macro e micronutrientes pelas hastes colhidas. Plantas que apresentaram hastes com maior comprimento e diâmetro apresentaram também maiores quantidades de nutrientes extraídos. Os nutrientes extraídos em maiores quantidades foram o N e o K. Com base na quantidade de nutrientes extraídos é possível que se faça o agrupamento de cvs. para estabelecer uma recomendação de fertilizantes para as cvs. com exigência nutricional semelhante.

Use of glass transition temperature for stabilization of board's cracks of Eucalyptus grandis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Síntese e caracterização de aluminofosfato impregnado com molibdênio/zinco visando a dessulfurização por adsorção

Discussions about pollution caused by vehicles emission are old and have been developed along the years. The search for cleaner technologies and frequent weather alterations have been inducing industries and government organizations to impose limits much more rigorous to the contaminant content in fuels, which have an direct impact in atmospheric emissions. Nowadays, the quality of fuels, in relation to the sulfur content, is carried out through the process of hydrodesulfurization. Adsorption processes also represent an interesting alternative route to the removal of sulfur content. Both processes are simpler and operate to atmospheric temperatures and pressures. This work studies the synthesis and characterization of aluminophosphate impregnate with zinc, molybdenum or both, and its application in the sulfur removal from the gasoline through the adsorption process, using a pattern gasoline containing isooctane and thiophene. The adsorbents were characterized by x-ray diffraction, differential thermal analysis (DTG), x-ray fluorescence and scanning electron microscopy (SEM). The specific area, volume and pore diameter were determined by BET (Brunauer- Emmet-Teller) and the t-plot method. The sulfur was quantified by elementary analysis using ANTEK 9000 NS. The adsorption process was evaluated as function of the temperature variation and initial sulfur content through the adsorption isotherm and its thermodynamic parameters. The parameters of entropy (ΔS), enthalpy variation (ΔH) and free Gibbs energy (ΔG) were calculated through the graph ln(Kd) versus 1/T. Langmuir, Freundlich and Langmuir-Freundlich models were adjusted to the experimental data, and the last one had presented better results. The thermodynamic tests were accomplished in different temperatures, such as 30, 40 and 50ºC, where it was concluded the adsorption process is spontaneous and exothermic. The kinetic of adsorption was studied by 24 h and it showed that the capability adsorption to the adsorbents studied respect the following order: MoZnPO > MoPO > ZnPO > AlPO. The maximum adsorption capacity was 4.91 mg/g for MoZnPO with an adsorption efficiency of 49%.

Anatomia comparada do lenho em raiz e caule de Lippia salviifolia Cham. (Verbenaceae)

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Desenvolvimento de protótipo de coletor automático destinado à coleta de amostras de água em corpos aquáticos para análise em laboratório

The aim of this approach is to describe the design and construction of a low-cost automated water sampler prototype. In recent years, there is an increasing need on the use of automated equipments for hydro climatic variables to be use in urban and rural environments. Such devices are always used to provide measured information which is of crucial importance on the development of water resources strategies at watershed scale. Actually, many research and water public institutions have been using these kinds of equipments. In most of the cases, automated equipments are expensive and need to be imported, generating a situation of technologic dependency. The prototype is based on an electronic system which controls a peristaltic pump functioning, five solenoid valves and an ultrasonic sensor connected to a datalloger. An interface with the user allows communication with a PC, when the equipment functioning parameters can be provided. The equipment has a hydraulic module composed by a 12V peristaltic pump connected to a distribution circuit composed by five solenoid valves, one of them being used to clean the circuit before each sampling procedure. Samples are collected by four 1.95 polyethylene bottles. The sampler body was made of acrylic material, with a cylindrical shape, and dimensions 0.72 m and 0.38 m height and diameter, respectively. The weight of the equipment without samples is approximately 15 kg, which infers to its portability. The prototype development total cost budget was approximately US$ 1,560.00. Laboratory tests aimed to evaluate the equipment performance and functioning demonstrated satisfactory results

Caracterização do lodo de lagoa anaeróbia tratando resíduos esgotados de tanques sépticos e fossas com vistas ao aproveitamento

The sludge generated in stabilization ponds can be designed for various purposes, among them we mention agricultural use, recovery of degraded areas and civil construction. The choice of these alternatives should be made based on qualitative and quantitative characteristics of the sludge. In this context, this study characterized the digested sludge from an anaerobic lagoon in Cidade do Natal/RN, which deals exclusively with residues of depleted septic tanks and pits. The sludge showed levels of macro and micronutrients that confirm its potential for agriculture, with 139.49 g.kg -1 organic matter, 15.40 g.kg-1 nitrogen and metal concentrations below those required by Resolution No. 375/06 of CONAMA, besides the absence of fecal coliform and less than 0.15 viable helminthes eggs/g, on average. The particle size distribution showed that most of the particles have a diameter similar to the sand, allowing the replacement of this input, for example. Analysis of the leachate and of the sludge solubilized classified as non-inert and non-hazardous according to NBR 10.004/04. The volume produced in three years of operation by the pond was 1903.50m³, equivalent to approximately 400 kg of dry sludge. Overall, the concentrations of the parameters were similar to literature, although none of them addresses sludge anaerobic pond treating sewer from septic tanks and pits.The sludgepresents technical feasibility to various types of use, however the cost of dewatering and especially with transport can derail it. It needs to be made a more thorough study of the costs to prove its economic viability

Otimização de um sistema de distribuição predial de água fria: estudo de caso

This dissertation presents a methodology to the optimization of a predial system of cold water distribution. It s about a study of a case applied to the Tropical Buzios Residential Condominium, located in the Búzio s Beach, Nísia Floresta city, the east coast of the Rio Grande do Norte state, twenty kilometers far from Natal. The design of cold water distribution networks according to Norm NBR 5626 of the ABNT - Brazilian Association of Techniques Norms, does not guarantee that the joined solution is the optimal solution of less cost. It s necessary the use of an optimization methodology, that supplies us, between all the possible solutions, the minimum cost solution. In the optimization process of the predial system of water distribution of the Tropical Búzios Condominium, is used Method Granados, that is an iterative algorithm of optimization, based on the Dynamic Programming, that supplies the minimum cost s network, in function of the piezometric quota of the reservoir. For the application of this Method in ramifies networks, is used a program of computer in C language. This process is divided in two stages: attainment of the previous solution and reduction of the piezometric quota of headboard. In the attainment of the previous solution, the minors possible diameters are used that guarantee the limit of maximum speed and the requirements of minimum pressures. The piezometric quota of headboard is raised to guarantee these requirements. In the second stage of the Granados Method, an iterative process is used and it objective is to reduce the quota of headboard gradually, considering the substitution of stretches of the network pipes for the subsequent diameters, considering a minimum addition of the network cost. The diameter change is made in the optimal stretch that presents the lesser Exchange Gradient. The process is locked up when the headboard quota of desired is reached. The optimized network s material costs are calculated, and is made the analysis of the same ones, through the comparison with the conventional network s costs

Atributos polarimétricos de imagem radar na inferência de parâmetros morfológicos de macrófitas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)