Gestão da segurança e saúde no trabalho em trabalhos de beneficiação rodoviária: perfil de autoestrada e a aplicação dos princípios gerais da prevenção à fase de execução da obra

Mestrado em Segurança e Higiene no Trabalho

Air pollution from traffic emissions in Oporto, Portugal: health and environmental implications

Air pollution represents a serious risk not only to environment and human health, but also to historical heritage. In this study, air pollution of the Oporto Metropolitan Area and its main impacts were characterized. The results showed that levels of CO, PM10 and SO2 have been continuously decreasing in the respective metropolitan area while levels of NOx and NO2 have not changed significantly. Traffic emissions were the main source of the determined polycyclic aromatic hydrocarbons (PAHs; 16 PAHs considered by U.S. EPA as priority pollutants, dibenzo[a,l]pyrene and benzo[j]fluoranthene) in air of the respective metropolitan area. The mean concentration of 18 PAHs in air was 69.9±39.7 ng m−3 with 3–4 rings PAHs accounting for 75% of the total ΣPAHs. The health risk analysis of PAHs in air showed that the estimated values of lifetime lung cancer risks considerably exceeded the health-based guideline level. Analytical results also confirm that historical monuments in urban areas act as passive repositories for air pollutants present in the surrounding atmosphere. FTIR and EDX analyses showed that gypsum was the most important constituent of black crusts of the characterized historical monument Monastery of Serra do Pilar classified as “UNESCO World Cultural Heritage”. In black crusts, 4–6 rings compounds accounted approximately for 85% of ΣPAHs. The diagnostic ratios confirmed that traffic emissions were the major source of PAHs in black crusts; PAH composition profiles were very similar for crusts and PM10 and PM2.5.

Perceção dos riscos ocupacionais em laboratórios de ortoprotesia na região de Lisboa e Vale do Tejo

Mestrado em Gestão e Avaliação de Tecnologias em Saúde

Persisting problems related to race and ethnicity in public health and epidemiology research

A recent and comprehensive review of the use of race and ethnicity in research that address health disparities in epidemiology and public health is provided. First it is described the theoretical basis upon which race and ethnicity differ drawing from previous work in anthropology, social science and public health. Second, it is presented a review of 280 articles published in high impacts factor journals in regards to public health and epidemiology from 2009-2011. An analytical grid enabled the examination of conceptual, theoretical and methodological questions related to the use of both concepts. The majority of articles reviewed were grounded in a theoretical framework and provided interpretations from various models. However, key problems identified include a) a failure from researchers to differentiate between the concepts of race and ethnicity; b) an inappropriate use of racial categories to ascribe ethnicity; c) a lack of transparency in the methods used to assess both concepts; and d) failure to address limits associated with the construction of racial or ethnic taxonomies and their use. In conclusion, future studies examining health disparities should clearly establish the distinction between race and ethnicity, develop theoretically driven research and address specific questions about the relationships between race, ethnicity and health. One argue that one way to think about ethnicity, race and health is to dichotomize research into two sets of questions about the relationship between human diversity and health.

Noise management at work

Every single day millions of European workers are exposed to noise at work. One in five of European’s workers have to raise his voice to be heard for at least half of the time that there are at work and 7% suffer from work-related hearing impairment. In Europe noise-induced hearing loss is the most common reported occupational disease. This paper deals with issues related with noise management at work, especially regarding the compliance with the new noise European Directive, (2003/10/EC).

A survey of technologies and applications for climbing robots locomotion and adhesion

The interest in the development of climbing robots has grown rapidly in the last years. Climbing robots are useful devices that can be adopted in a variety of applications, such as maintenance and inspection in the process and construction industries. These systems are mainly adopted in places where direct access by a human operator is very expensive, because of the need for scaffolding, or very dangerous, due to the presence of an hostile environment. The main motivations are to increase the operation efficiency, by eliminating the costly assembly of scaffolding, or to protect human health and safety in hazardous tasks. Several climbing robots have already been developed, and other are under development, for applications ranging from cleaning to inspection of difficult to reach constructions. A wall climbing robot should not only be light, but also have large payload, so that it may reduce excessive adhesion forces and carry instrumentations during navigation. These machines should be capable of travelling over different types of surfaces, with different inclinations, such as floors, walls, or ceilings, and to walk between such surfaces (Elliot et al. (2006); Sattar et al. (2002)). Furthermore, they should be able of adapting and reconfiguring for various environment conditions and to be self-contained. Up to now, considerable research was devoted to these machines and various types of experimental models were already proposed (according to Chen et al. (2006), over 200 prototypes aimed at such applications had been developed in the world by the year 2006). However, we have to notice that the application of climbing robots is still limited. Apart from a couple successful industrialized products, most are only prototypes and few of them can be found in common use due to unsatisfactory performance in on-site tests (regarding aspects such as their speed, cost and reliability). Chen et al. (2006) present the main design problems affecting the system performance of climbing robots and also suggest solutions to these problems. The major two issues in the design of wall climbing robots are their locomotion and adhesion methods. With respect to the locomotion type, four types are often considered: the crawler, the wheeled, the legged and the propulsion robots. Although the crawler type is able to move relatively faster, it is not adequate to be applied in rough environments. On the other hand, the legged type easily copes with obstacles found in the environment, whereas generally its speed is lower and requires complex control systems. Regarding the adhesion to the surface, the robots should be able to produce a secure gripping force using a light-weight mechanism. The adhesion method is generally classified into four groups: suction force, magnetic, gripping to the surface and thrust force type. Nevertheless, recently new methods for assuring the adhesion, based in biological findings, were proposed. The vacuum type principle is light and easy to control though it presents the problem of supplying compressed air. An alternative, with costs in terms of weight, is the adoption of a vacuum pump. The magnetic type principle implies heavy actuators and is used only for ferromagnetic surfaces. The thrust force type robots make use of the forces developed by thrusters to adhere to the surfaces, but are used in very restricted and specific applications. Bearing these facts in mind, this chapter presents a survey of different applications and technologies adopted for the implementation of climbing robots locomotion and adhesion to surfaces, focusing on the new technologies that are recently being developed to fulfill these objectives. The chapter is organized as follows. Section two presents several applications of climbing robots. Sections three and four present the main locomotion principles, and the main "conventional" technologies for adhering to surfaces, respectively. Section five describes recent biological inspired technologies for robot adhesion to surfaces. Section six introduces several new architectures for climbing robots. Finally, section seven outlines the main conclusions.

Development of biocompatible and “smart” porous structures using CO2-assisted processes

Dissertação apresentada para a obtenção do grau de Doutor em Engenharia Química, especialidade Engenharia da Reacção Química, pela Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

Maternal mental health and nutritional status of six-month-old infants

ABSTRACT OBJECTIVE To analyze if maternal mental health is associated with infant nutritional status at six month of age. METHODS A cross-sectional study with 228 six-month-old infants who used primary health care units of the city of Rio de Janeiro, Southeastern Brazil. Mean weight-for-length and mean weight-for-age were expressed in z-scores considering the 2006 World Health Organization reference curves. Maternal mental health was measured by the 12-item General Health Questionnaire. The following cutoff points were used: ≥ 3 for common mental disorders, ≥ 5 for more severe mental disorders, and ≥ 9 for depression. The statistical analysis employed adjusted linear regression models. RESULTS The prevalence of common mental disorders, more severe mental disorders and depression was 39.9%, 23.7%, and 8.3%, respectively. Children of women with more severe mental disorders had, on average, a weight-for-length 0.37 z-scores lower than children of women without this health harm (p = 0.026). We also observed that the weight-for-length indicator of children of depressed mothers was, on average, 0.67 z-scores lower than that of children of nondepressed women (p = 0.010). Maternal depression was associated with lower mean values of weight-for-age z-scores (p = 0.041). CONCLUSIONS Maternal mental health is positively related to the inadequacy of the nutritional status of infants at six months.

Avaliação de riscos ambientais e profissionais na indústria metalomecânica

A preservação e proteção do ambiente são, cada vez mais, de elevada importância. Para fazer face ao grande consumo de bens, que se verifica nos dias de hoje, a atividade industrial tem aumentado, assim como os resíduos, as emissões, os efluentes e ainda os resíduos de produtos em fim de vida, provocando impactes no meio ambiente, com alterações significativas que se manifestam a nível das condições climáticas e, consequentemente, afetam a qualidade de vida das pessoas a sua segurança e saúde, bem como a fauna e a flora. O presente estudo tem por objetivo identificar as principais atividades desenvolvidas na indústria metalomecânica, identificar os principais aspetos e impactes ambientais, bem como os perigos e riscos profissionais associados às atividades deste setor, identificar a principal legislação em vigor em matéria ambiental e de segurança e saúde no trabalho, selecionar e analisar metodologias de avaliação de riscos ambientais e profissionais e aplicar estas metodologias num estudo de caso numa empresa metalomecânica, tendo em vista comparar os resultados das avaliações, por duas metodologias diferentes, dos riscos ambientais e profissionais e daí tirar conclusões. A vantagem da aplicação de duas metodologias diferentes na avaliação de riscos ambientais e profissionais é a de poder aferir se os resultados são idênticos independentemente da metodologia utilizada. Após a aplicação das duas metodologias, com critérios de avaliação diferentes, selecionadas para avaliação dos riscos ambientais, concluiu-se que as metodologias apresentam resultados semelhantes, o mesmo aconteceu com as duas metodologias, com critérios de avaliação, também, diferentes, selecionadas para avaliação dos riscos profissionais em que as duas metodologias apresentaram os mesmos resultados.

Climbing robots: a survey of technologies and applications

The interest in the development of climbing robots is growing rapidly. Motivations are typically to increase the operation efficiency by obviating the costly assembly of scaffolding or to protect human health and safety in hazardous tasks. Climbing robots are starting to be developed for applications ranging from cleaning to inspection of difficult to reach constructions. These robots should be capable of travelling on different types of surfaces, with varying inclinations, such as floors, walls, ceilings, and to walk between such surfaces. Furthermore, these machines should be capable of adapting and reconfiguring for various environment conditions and to be self-contained. Regarding the adhesion to the surface, they should be able to produce a secure gripping force using a light-weight mechanism. This paper presents a survey of different applications and technologies proposed for the implementation of climbing robots.

Chronic disease prevention and health promotion. Public policies and social network analysis of the hospitals services and oyhers health and social organizations to support joint action for children with diabetes

Comunicação apresentada na 18th Conference International of Health Promotion Hospitals & Health Services "Tackling causes and consequences of inequalities in health: contributions of health services and the HPH network", em Manchester de 14-16 de april de 2010

Validação de tecnologias de informação e comunicação no suporte a um sistema integrado de gestão orientado para o setor agroalimentar

Dissertação de Mestrado em Gestão Integrada da Qualidade, Ambiente e Segurança

Implementação de um Sistema Integrado de Gestão da Qualidade e Segurança e Saúde do Trabalho

Dissertação de Mestrado em Gestão Integrada Qualidade, ambiente e Segurança

Sistema de Gestão Integrado da Qualidade e Segurança do trabalho numa IPSS

Dissertação de Mestrado em Gestão Integrada da Qualidade, Ambiente e Segurança

Effects of Exercise on Physical and Mental Health, and Cognitive and Brain Functions in Schizophrenia: Clinical and Experimental Evidence

Exercise promotes several health benefits, such as cardiovascular, musculoskeletal and cardiorespiratory improvements. It is believed that the practice of exercise in individuals with psychiatric disorders, e.g. schizophrenia, can cause significant changes. Schizophrenic patients have problematic lifestyle habits compared with general population; this may cause a high mortality rate, mainly caused by cardiovascular and metabolic diseases. Thus, the aim of this study is to investigate changes in physical and mental health, cognitive and brain functioning due to the practice of exercise in patients with schizophrenia. Although still little is known about the benefits of exercise on mental health, cognitive and brain functioning of schizophrenic patients, exercise training has been shown to be a beneficial intervention in the control and reduction of disease severity. Type of training, form of execution, duration and intensity need to be better studied as the effects on physical and mental health, cognition and brain activity depend exclusively of interconnected factors, such as the combination of exercise and medication. However, one should understand that exercise is not only an effective nondrug alternative, but also acts as a supporting linking up interventions to promote improvements in process performance optimization. In general, the positive effects on mental health, cognition and brain activity as a result of an exercise program are quite evident. Few studies have been published correlating effects of exercise in patients with schizophrenia, but there is increasing evidence that positive and negative symptoms can be improved. Therefore, it is important that further studies be undertaken to expand the knowledge of physical exercise on mental health in people with schizophrenia, as well as its dose-response and the most effective type of exercise.