Mathematical relationships for metal build-up on urban road surfaces based on traffic and land use characteristics

The study investigated the influence of traffic and land use parameters on metal build-up on urban road surfaces. Mathematical relationships were developed to predict metals originating from fuel combustion and vehicle wear. The analysis undertaken found that nickel and chromium originate from exhaust emissions, lead, copper and zinc from vehicle wear, cadmium from both exhaust and wear and manganese from geogenic sources. Land use does not demonstrate a clear pattern in relation to the metal build-up process, though its inherent characteristics such as traffic activities exert influence. The equation derived for fuel related metal load has high cross-validated coefficient of determination (Q2) and low Standard Error of Cross-Validation (SECV) values indicates that the model is reliable, while the equation derived for wear-related metal load has low Q2 and high SECV values suggesting its use only in preliminary investigations. Relative Prediction Error values for both equations are considered to be well within the error limits for a complex system such as an urban road surface. These equations will be beneficial for developing reliable stormwater treatment strategies in urban areas which specifically focus on mitigation of metal pollution.

Pulmonary embolism in the emergency department : a Singaporean nursing case review

Introduction The presentation of pulmonary embolism to the emergency department (ED) can prove challenging because of the myriad of potential disease processes that mimic its signs and symptoms. The incidence of pulmonary embolism and indeed the mortality associated with it is relatively high. Early diagnosis and treatment is crucial in off-setting the potential deleterious effects associated with this condition. The aim of this article is to present a nursing case review of a patient presenting to the ED with a diagnosis of pulmonary embolism. Method We chose to use a case review to highlight the nursing and medical care that was provided for a patient who presented to the emergency department acutely with dyspnoea, chest pain and pyrexia. The use of case reviews are useful in reporting unusual or rare cases and this format is typically seen more in medicine than in nursing. They can naturally take one of two formats—a single case report or a series of case reports; in this case we opted to report on a single case. Discussion The gentleman in question was an ambulance admissionto the ED with a three day history of chest pain, shortness of breath and one episode of syncope which brought him to the ED. Over the course of his admission a variety of treatment modalities were used successfully to alleviate the problem. More notable from a nursing perspective was the use of diagnostic tools as an interpretation to guide his care and provide a platform from which a deeper understanding and appreciation of the intricacies the critically ill patient often presents. Conclusion We found the use of case review very enlightening in understanding the disease process and the decision-making that accompanies this. Whilst our patient was successfully rehabilitated home, we learnt a lot from the experience which has been most beneficial in supporting our understanding of pulmonary embolism.

Advanced arterial blood gas analysis in septic shock : a Singaporean nursing case review.

Introduction The admission to the Intensive Care Unit with a diagnosis of sepsis and/or septic shock is not uncommon. The aim of this article is to present a nursing case review of a patient admitted to the intensive care unit with a diagnosis of septic shock and the use of bedside acid–base formulae to inform clinical decision making. Method We chose to use a case review. This method is useful in reporting unusual or rare cases and is typically seen more in medicine than in nursing. Discussion The gentleman in question was a self-presentation with a short history of fever and worsening shortness of breath. His condition worsened where he required admission to the intensive care unit. The use of ‘advanced’ acid–base interpretation to guide his nursing care provided a platform from which to advance a deeper understanding of the intricacies the critically ill patient often presents. Conclusion The use of case review is enlightening in understanding the disease process and the decision-making that accompanies this. The lessons learnt are applicable to a wider nursing audience because understanding acid–base physiology is beneficial in supporting and advancing critical care nursing practice.

Public sector project delay : the Malaysian perspective and the way forward

Construction delay has been a protracted problem for the Malaysian construction industry. Recent report showed that 80% of public sector projects are behind schedule. This underachieving time performance has led to many problems including public complaints, loss of reputation and revenue for the government and a slump in the industry’s GDP contribution. Research in the area of project delay has mushroomed worldwide with attempts to place mitigation plans, but delay remains a global phenomenon. There is now an urgent need for revolutionizing construction practices and past research, backed up with few successful cases suggests that Supply Chain Management (SCM) could prove beneficial to reduce or eliminate delays in construction. SCM which originated from the automotive manufacturing industry promotes a more collaborative approach to construction management and has recently gained attention of the construction industry. However every country, including Malaysia, would certainly have disparities of their own compared to others being it from the cultural point of view, nature of problems, locality or improvements needed. Therefore, this paper will present part of a Ph.D. research which aims at illustrating the Malaysian construction industry experts’ perception of the Malaysian public sector project delay, provide insight into these dilemmas, highlights the problems with current practices, its effects and the improvements needed. Subsequently, this paper would propose ratification to the problems using SCM. A semi-structured interview has been conducted to practitioners with at least 20 years’ experience in the industry. The findings showed that Malaysia may be unique compared to other countries and that by considering a number of additional factors, SCM could prove beneficial to increase efficiency of the Malaysian public sector projects.

Consolidation of business process model collections

This thesis presents novel techniques for addressing the problems of continuous change and inconsistencies in large process model collections. The developed techniques treat process models as a collection of fragments and facilitate version control, standardization and automated process model discovery using fragment-based concepts. Experimental results show that the presented techniques are beneficial in consolidating large process model collections, specifically when there is a high degree of redundancy.

Status of the world's remaining closed forests : an assessment using satellite data and policy options

Historically, it appears that some of the WRCF have survived because i) they lack sufficient quantity of commercially valuable species; ii) they are located in remote or inaccessible areas; or iii) they have been protected as national parks and sanctuaries. Forests will be protected when people who are deciding the fate of forests conclude than the conservation of forests is more beneficial, e.g. generates higher incomes or has cultural or social values, than their clearance. If this is not the case, forests will continue to be cleared and converted. In the future, the WRCF may be protected only by focused attention. The future policy options may include strategies for strong protection measures, the raising of public awareness about the value of forests, and concerted actions for reducing pressure on forest lands by providing alternatives to forest exploitation to meet the growing demands of forest products. Many areas with low population densities offer an opportunity for conservation if appropriate steps are taken now by the national governments and international community. This opportunity must be founded upon the increased public and government awareness that forests have vast importance to the welfare of humans and ecosystems' services such as biodiversity, watershed protection, and carbon balance. Also paramount to this opportunity is the increased scientific understanding of forest dynamics and technical capability to install global observation and assessment systems. High-resolution satellite data such as Landsat 7 and other technologically advanced satellite programs will provide unprecedented monitoring options for governing authorities. Technological innovation can contribute to the way forests are protected. The use of satellite imagery for regular monitoring and Internet for information dissemination provide effective tools for raising worldwide awareness about the significance of forests and intrinsic value of nature.

Insect mitochondrial genomics : implications for evolution and phylogeny

The mitochondrial (mt) genome is, to date, the most extensively studied genomic system in insects, outnumbering nuclear genomes tenfold and representing all orders versus very few. Phylogenomic analysis methods have been tested extensively, identifying compositional bias and rate variation, both within and between lineages, as the principal issues confronting accurate analyses. Major studies at both inter- and intraordinal levels have contributed to our understanding of phylogenetic relationships within many groups. Genome rearrangements are an additional data type for defining relationships, with rearrangement synapomorphies identified across multiple orders and at many different taxonomic levels. Hymenoptera and Psocodea have greatly elevated rates of rearrangement offering both opportunities and pitfalls for identifying rearrangement synapomorphies in each group. Finally, insects are model systems for studying aberrant mt genomes, including truncated tRNAs and multichromosomal genomes. Greater integration of nuclear and mt genomic studies is necessary to further our understanding of insect genomic evolution.

Gas sensing of ruthenium implanted tungsten oxide thin films

Different amounts of Ru were implanted into thermally evaporated WO3 thin films by ion implantation. The films were subsequently annealed at 600oC for 2 hours in air to remove defects generated during the ion implantation. The Ru concentrations of four samples have been quantified by Rutherford Backscattering Spectrometry as 0.8, 5.5, 9 and 11.5 at%. The un-implanted WO3 films were highly porous but the porosity decreased significantly after ion implantation as observed by Transmission Electron Microscopy and Scanning Electron Microscopy. The thickness of the films also decreased with increasing Ru-ion dose, which is mainly due to densification of the porous films during ion implantation. From Raman spectroscopy two peaks at 408 and 451 cm-1 (in addition to the typical vibrational peaks of the monoclinic WO3 phase) associated with Ru were observed. Their intensity increased with increasing Ru concentration. X-Ray Photoelectron Spectroscopy showed a metallic state of Ru with binding energy of Ru 3d5/2 at 280.1 eV. This peak position remained almost unchanged with increasing Ru concentration. The resistances of the Ru-implanted films were found to increase in the presence of NO2 and NO with higher sensor response to NO2. The effect of Ru concentration on the sensing performance of the films was not explicitly observed due to reduced film thickness and porosity with increasing Ru concentration. However, the results indicate that the implantation of Ru into WO3 films with sufficient film porosity and film thickness can be beneficial for NO2 sensing at temperatures in the range of 250°C to 350°C.

Bauxite residue neutralisation precipitate stability in acidic environments

This investigation used a combination of techniques, such as X-ray diffraction, inductively coupled plasma optical emission spectroscopy and infrared spectroscopy, to determine the dissolution mechanisms of the Bayer precipitate and the associated rate of dissolution in acetic, citric and oxalic acid environments. The Bayer precipitate is a mixture of hydrotalcite, calcium carbonate and sodium chloride that forms during the seawater neutralisation of Bayer liquors (waste residue of the alumina industry). The dissolution rate of a Bayer precipitate is found to be dependent on (1) the strength of the organic acid and (2) the number of donating H+ ions. The dissolution mechanism for a Bayer precipitate consists of several steps involving: (1) the dissolution of CaCO3, (2) formation of whewellite (calcium oxalate) when oxalic acid is used and (3) multiple dissolution steps for hydrotalcite that are highly dependent on the pH of solution. The decomposition of the Al–OH hydrotalcite layers resulted in the immediate formation of Al(OH)3, which is stable until the pH decreases below 5.5. This investigation has found that the Bayer precipitate is stable across a wide pH range in the presence of common organic acids found in the rhizosphere, and that initial decomposition steps are likely to be beneficial in supporting plant growth through the release of nutrients such as Ca2þ and Mg2þ.

Privacy enhancements for hardware-based security modules

The increasing growth in the use of Hardware Security Modules (HSMs) towards identification and authentication of a security endpoint have raised numerous privacy and security concerns. HSMs have the ability to tie a system or an object, along with its users to the physical world. However, this enables tracking of the user and/or an object associated with the HSM. Current systems do not adequately address the privacy needs and as such are susceptible to various attacks. In this work, we analyse various security and privacy concerns that arise when deploying such hardware security modules and propose a system that allow users to create pseudonyms from a trusted master public-secret key pair. The proposed system is based on the intractability of factoring and finding square roots of a quadratic residue modulo a composite number, where the composite number is a product of two large primes. Along with the standard notion of protecting privacy of an user, the proposed system offers colligation between seemingly independent pseudonyms. This new property when combined with HSMs that store the master secret key is extremely beneficial to a user, as it offers a convenient way to generate a large number of pseudonyms using relatively small storage requirements.

Certified pseudonyms colligated with master secret key

A pseudonym provides anonymity by protecting the identity of a legitimate user. A user with a pseudonym can interact with an unknown entity and be confident that his/her identity is secret even if the other entity is dishonest. In this work, we present a system that allows users to create pseudonyms from a trusted master public-secret key pair. The proposed system is based on the intractability of factoring and finding square roots of a quadratic residue modulo a composite number, where the composite number is a product of two large primes. Our proposal is different from previously published pseudonym systems, as in addition to standard notion of protecting privacy of an user, our system offers colligation between seemingly independent pseudonyms. This new property when combined with a trusted platform that stores a master secret key is extremely beneficial to an user as it offers a convenient way to generate a large number of pseudonyms using relatively small storage.

Hybrid genetic algorithm for elimination of severe stress concentration in railhead ends

This paper presents a computational method for eliminating severe stress concentration at the unsupported railhead ends in rail joints through innovative shape optimization of the contact zone, which is complex due to near field nonlinear contact. With a view to minimizing the computational efforts, hybrid genetic algorithm method coupled with parametric finite element has been developed and compared with the traditional genetic algorithm (GA). The shape of railhead top surface where the wheel contacts nonlinearly was optimized using the hybridized GA method. Comparative study of the optimal result and the search efficiency between the traditional and hybrid GA methods has shown that the hybridized GA provides the optimal shape in fewer computational cycles without losing accuracy. The method will be beneficial to solving complex engineering problems involving contact nonlinearity.

Safety climate : recent developments and future implications

Safety climate is a current interest to construction practitioners and researchers. The concept of safety climate has been actively explored in the field of Industrial and Organizational (I/O) psychology but yet in the construction industry. This paper aims to review the literature of safety climate in a systematic manner and highlight future directions for safety research and development of safety practices in the construction industry. The value of safety climate lies on its ability to predict safety behavior. Safety climate, as a mediator, unfolds the relationship between organizational variables and safety behavior. It, as a moderator, affects the effectiveness of any safety initiatives to improve safety performance. Future research directions would be likely to look at relationship between organizational factors and safety climate using multi-level analysis. To the construction industry, safety climate measurement is a good indicator to assess safety performance. Empirical studies show that frontline supervisor would be the best conduit to create a positive safety climate at workgroup level. It is believed that this paper is beneficial to researchers interested in behavioral aspect of construction safety and industry practitioners striving for safety on site.

Amateur-to-amateur

Copyright, it is commonly said, matters in society because it encourages the production of socially beneficial, culturally significant expressive content. Our focus on copyright's recent history, however, blinds us to the social information practices that have always existed. In this Article, we examine these social information practices, and query copyright's role within them. We posit a functional model of what is necessary for creative content to move from creator to user. These are the functions dealing with the creation, selection, production, dissemination, promotion, sale, and use of expressive content. We demonstrate how centralized commercial control of information content has been the driving force behind copyright's expansion. All of the functions that copyright industries once controlled, however, are undergoing revolutionary decentralization and disintermediation. Different aspects of information technology, notably the digitization of information, widespread computer ownership, the rise of the Internet, and the development of social software, threaten the viability and desirability of centralized control over every one of the content functions. These functions are increasingly being performed by individuals and disaggregated groups. This raises an issue for copyright as the main regulatory force in information practices: copyright assumes a central control requirement that no longer applies for the development of expressive content. We examine the normative implications of this shift for our information policy in this new post-copyright era. Most notably, we conclude that copyright law needs to be adjusted in order to recognize the opportunity and desirability of decentralized content, and the expanded marketplace of ideas it promises.

Gambling on gambling in Baccarat : financial implications of raising bet limits and table differentials

The house advantage for Baccarat is known, hence the theoretical win can be determined. What is impractical to theoretically determine is the frequency and financial implications of extreme events, for example, prolonged winning streaks coupled with various betting patterns. The simulation herein provides such granularity. We explore the effect of following the „hot hand‟, that is, rapidly escalating bets when players are on a winning streak. To minimize their exposure, casino management sets a table bet maximum as well as a table differential. These figures can and do serve as a means to differentiate one casino from another. As the allowable bet maximum increases so does the total amount bet, which increases the theoretical winnings, thus suggesting that a high bet limit and differential is beneficial for the house. However, the greater are these amounts, the greater the number of shoes that end with players losing relative to a constant betting scenario (the number of times a player wins at all can drop from ~47% of the time to less than a quarter); but there will, on occasion, be more extreme payouts to players. This simulation is therefore intended to help casino managers set betting limits that maximize total winnings while bearing in mind both the likelihood and magnitude of negative outcomes to the casino.