Analysis of two reinforced concrete pile caps with embedded sockets in the presence of a locking beam

The present research studies the behavior of reinforced concrete locking beams supported by two capped piles with the socket embedded; used as connections for pre-cast concrete structures. The effect provoked by locking the beam on the pile-caps when supported by the lateral socket walls was evaluated. Three-dimensional numerical analyses using software based on the finite element method (FEM) were developed considering the nonlinear physical behavior of the material. To evaluate the adopted software, a comparative analysis was made using the numerical and experimented results obtained from other software. In the pile caps studied, a variation in the wall thickness, socket interface, strut angle inclination and action on beam. The results show that the presence of a beam does not significantly change pile cap behavior and that the socket wall is able to effectively transfer the force from the beam to the pile caps. By the tensions on the bars of longitudinal reinforcement, it was possible to obtain the force on the tie and the strut angle inclination before the collapse of models. It was found that the angles present more inclinations than those used in the design, which was made based on a strut-and-tie model. More results are available at http://www.set.eesc.usp.br/pdf/download/2009ME_RodrigoBarros.pdf

Optimal synthesis of anaerobic digester networks

The objective of this paper is to develop a mathematical model for the synthesis of anaerobic digester networks based on the optimization of a superstructure that relies on a non-linear programming formulation. The proposed model contains the kinetic and hydraulic equations developed by Pontes and Pinto [Chemical Engineering journal 122 (2006) 65-80] for two types of digesters, namely UASB (Upflow Anaerobic Sludge Blanket) and EGSB (Expanded Granular Sludge Bed) reactors. The objective function minimizes the overall sum of the reactor volumes. The optimization results show that a recycle stream is only effective in case of a reactor with short-circuit, such as the UASB reactor. Sensitivity analysis was performed in the one and two-digester network superstructures, for the following parameters: UASB reactor short-circuit fraction and the EGSB reactor maximum organic load, and the corresponding results vary considerably in terms of digester volumes. Scenarios for three and four-digester network superstructures were optimized and compared with the results from fewer digesters. (C) 2009 Elsevier B.V. All rights reserved.

Mesoporous dye-doped titanium dioxide for micro-optoelectronic applications

Optically transparent, mesostructured titanium dioxide thin films were fabricated using an amphiphilic poly(alkylene oxide) block copolymer template in combination with retarded hydrolysis of a titanium isopropoxide precursor. Prior to calcination, the films displayed a stable hexagonal mesophase and high refractive indices (1.5 to 1.6) relative to mesostructured silica (1.43). After calcination, the hexagonal mesophase was retained with surface areas >300 m2 g-1. The dye Rhodamine 6G (commonly used as a laser dye) was incorporated into the copolymer micelle during the templating process. In this way, novel dye-doped mesostructured titanium dioxide films were synthesised. The copolymer not only directs the film structure, but also provides a solubilizing environment suitable for sustaining a high monomer-to-aggregate ratio at elevated dye concentrations. The dye-doped films displayed optical thresholdlike behaviour characteristic of amplified spontaneous emission. Soft lithography was successfully applied to micropattern the dye-doped films. These results pave the way for the fabrication and demonstration of novel microlaser structures and other active optical structures. This new, high-refractive index, mesostructured, dye-doped material could also find applications in areas such as optical coatings, displays and integrated photonic devices.

(FAB01_091) Book reviews

Leon Battista Alberti, 'On the Art of Building in Ten Books' Translated by Joseph Rykwert, Neil Leach and Robert Tavemor L. A. Zhadova (ed.), 'Tatlin' (Budapest 1984). English translation Helen Ross, 'Just For Living, Aboriginal Perceptions of Housing in North West Australia' Tony Fry, 'Design History Australia: A Source Text in Methods and Resources' Phillip Cox and David Moore, 'The Australian Functional Tradition' Lenore Coltheart and Don Fraser (eds.), 'Lamdmarks in Public Works, Engineers and Their Works in New South Wales 1884-1914' Peter Bridges and Don MacDonald, 'James Barnet, Colonial Architect' Don Watson and Judith McKay, 'A Directory of Queensland Architects to 1940' Russell Walden, 'Voices of Silence: New Zealand's Chapel of Futuna' Jeremy Salmond, 'Old New Zealand Houses 1800-1940' Victoria Middleton, 'The Legend of Green Valley' Dyranda Prevost and Ann Rado, 'Living Places' Mark Jackson and Mark Stiles (directors), 'Universal Provider' Lars Lerup, 'Planned Assaults'

Innovation as a Meta-Attribute for Graduate Engineers

This paper reviews the attitudes, skills and knowledge that engineering innovators should possess. It critically analyses and compares sets of graduate attributes from the USA, Australia and Malaysia in terms of which of these relate to the ability to innovate. Innovation can be described as an integrative, meta attribute that overarches most of the other graduate attributes. Due to the “graduate attribute paradox”, it is shown how meeting the stated attributes of graduates by industry does not necessarily satisfy the requirements of industry. It is argued that the culture of the engineering school is an important influence on fostering innovation in engineers.

Eco-efficiency for the Dairy Processing Industry

This manual has been developed to help the Australian dairy processing industry increase its competitiveness through increased awareness and uptake of eco-efficiency. The manual seeks to consolidate and build on existing knowledge, accumulated through projects and initiatives that the industry has previously undertaken to improve its use of raw materials and resources and reduce the generation of wastes. Where there is an existing comprehensive report or publication, the manual refers to this for further information. Eco-efficiency is about improving environmental performance to become more efficient and profitable. It is about producing more with less. It involves applying strategies that will not only ensure efficient use of resources and reduction in waste, but will also reduce costs. This chapter outlines the environmental challenges faced by Australian dairy processors. The manual explores opportunities for reducing environmental impacts in relation to water, energy, product yield, solid and liquid waste reduction and chemical use.

Superior electric double layer capacitors using ordered mesoporous carbons

This paper reports for the first time superior electric double layer capacitive properties of ordered mesoporous carbon (OMCs) with varying ordered pore symmetries and mesopore structure. Compared to commercially used activated carbon electrode, Maxsorb, these OMC carbons have superior capacitive behavior, power output and high-frequency performance in EDLCs due to the unique structure of their mesopore network, which is more favorable for fast ionic transport than the pore networks in disordered microporous carbons. As evidenced by N-2 sorption, cyclic voltammetry and frequency response measurements, OMC carbons with large mesopores, and especially with 2-D pore symmetry, show superior capacitive behaviors (exhibiting a high capacitance of over 180 F/g even at very high sweep rate of 50 mV/s, as compared to much reduced capacitance of 73 F/g for Maxsorb at the same sweep rate). OMC carbons can provide much higher power density while still maintaining good energy density. OMC carbons demonstrate excellent high-frequency performances due to its higher surface area in pores larger than 3 nm. Such ordered mesoporous carbons (OMCs) offer a great potential in EDLC capacitors, particularly for applications where high power output and good high-frequency capacitive performances are required. (C) 2005 Elsevier Ltd. All rights reserved.

Analysis of Piezoelectric sensor to detect flexural waves

The electromechanical transfer characteristics of adhesively bonded piezoelectric sensors are investigated. By the use of dynamic piezoelectricity theory, Mindlin plate theory for flexural wave propagation, and a multiple integral transform method, the frequency-response functions of piezoelectric sensors with and without backing materials are developed and the pressure-voltage transduction functions of the sensors calculated. The corresponding simulation results show that the sensitivity of the sensors is not only dependent on the sensors' inherent features, such as piezoelectric properties and geometry, but also on local characteristics of the tested structures and the admittance and impedance of the attached electrical circuit. It is also demonstrated that the simplified rigid mass sensor model can be used to analyze successfully the sensitivity of the sensor at low frequencies, but that the dynamic piezoelectric continuum model has to be used for higher frequencies, especially around the resonance frequency of the coupled sensor-structure vibration system.

From aesthetic principles to collective sentiments: The logics of everyday judgements of taste

Contemporary research into the sociology of taste has, following Bourdieu (1984), primarily emphasised the role of social position, or more broadly as implicated int he reproduction of social inequality. We argue that although important, such a preoccupation with the social distribution of objectified tastes--for example in music, literature, and art--has been at the expense of investigating the everyday perceptual schemes and resources used by actors to accomplish a judgement of taste. Our argument is traced using a range of classical and contemporary literature which deals with the personal/collective tension in taste, aesthetics and fashion. We use data from a recent national survey to investigate how a sample of ordinary fashion. We use data from a recent national survey to investigate how a sample of ordinary actors understand the categories of 'good' and 'bad' taste. The analysis shows a strong collective strand in everyday definitions of taste, often linked to moral codes of interpersonal conduct. Also, taste is largely defined by people as a strategy for managing relations with others, and as a mode of self-discipline which relies on the mastery of a number of general principles that are resources for people to position their own tastes within an imagined social sphere. This paper proposes a schematic model which accounts for the range of discriminatory resources used to make judgements of taste.

The supportive care needs of men with prostate cancer (2000)

The diagnosis and subsequent treatment of prostate cancer is followed by a range of significant disease specific and iatrogenic sequelae. However, the supportive care needs of men with prostate cancer are not well described in the literature. The present study assesses the supportive care needs of men with prostate cancer who are members of prostate cancer self-help groups in Queensland, Australia. In all, 206 men aged between 48 and 85 years (mean = 68) completed the Supportive Care Needs Survey (SCNS) (62% response). The SCNS is a validated measure assessing perceived need in the domains of psychological needs, health system and information needs, physical and daily living needs, patient care and support, and sexuality. Items assessing need for access to services and resources were also included. One third of the sample reported a moderate to high need for help for multiple items in the sexuality, psychological and health system and information domains. Younger men reported greater need in the sexuality domain; living in major urban centres was predictive of greater psychological need; being closer to the time of diagnosis was related to greater need for help in the physical and daily living domain; having prostate cancer that is not in remission, having received radiation therapy, and lower levels of education were predictive of greater need for help in patient care and support. Of the total sample, 55% of men had used alternative cancer treatments in the past 12 months, with younger and more educated men more likely to use alternative therapies. Interventions in sexuality, psychological concerns and informational support are priorities for men with prostate cancer. Copyright (C) 2001 John Wiley & Sons, Ltd.

A beam-forming network for a circular switched-beam phased array antenna

This paper reports on the design and development of a dividing/phasing network for a compact switched-beam array antenna for Land-vehicle mobile satellite communications, The device is formed by a switched radial divider/combiner and 1-bit phase shifters and generates a sufficient number of beams for the proper satellite tracking.

On the fast approximation of Green's functions in MPIE formulations for planar layered media

The numerical implementation of the complex image approach for the Green's function of a mixed-potential integralequation formulation is examined and is found to be limited to low values of k(0) rho (in this context k(0) rho = 2 pirho/ lambda(0), where rho is the distance between the source and the field points of the Green's function and lambda(0) is the free space wavelength). This is a clear limitation for problems of large dimension or high frequency where this limit is easily exceeded. This paper examines the various strategies and proposes a hybrid method whereby most of the above problems can be avoided. An efficient integral method that is valid for large k(0) rho is combined with the complex image method in order to take advantage of the relative merits of both schemes. It is found that a wide overlapping region exists between the two techniques allowing a very efficient and consistent approach for accurately calculating the Green's functions. In this paper, the method developed for the computation of the Green's function is used for planar structures containing both lossless and lossy media.

An inverse design of an open, head/neck RF coil for MRI

Radio-frequency (RF) coils are a necessary component of magnetic resonance imaging (MRI) systems. When used in transmit operation, they act to generate a homogeneous RF magnetic field within a volume of interest and when in receive operation, they act to receive the nuclear magnetic resonance signal from the RF-excited specimen. This paper outlines a procedure for the design of open RF coils using the time-harmonic inverse method. This method entails the calculation of an ideal current density on a multipaned planar surface that would generate a specified magnetic field within the volume of interest. Because of the averaging effect of the regularization technique in the matrix solution, the specified magnetic field is shaped within an iterative procedure until the generated magnetic field matches the desired magnetic field. The stream-function technique is used to ascertain conductor positions and a method of moments package is then used to finalize the design. An open head/neck coil was designed to operate in a clinical 2T MRI system and the presented results prove the efficacy of this design methodology.

Ellipsoidal harmonic (Lame) MRI shims

Ellipsoidal harmonics are presented as a basis function set for the design of shim coils for magnetic resonance imaging (MRI) or spectroscopy. MR shim coils may be either superconductive or resistive. Ellipsoidal harmonics form an orthogonal set over an ellipsoid and hence are appropriate in circumstances where the imaging or spectroscopic region of a magnet more closely conforms to an ellipsoid rather than a sphere. This is often the case in practice. The Cartesian form of ellipsoidal harmonics is discussed. A method for the design of streamline coil designs is detailed and patterns for third-order ellipsoidal (Lame) shims wound on a cylindrical surface are presented.