Medidas de propiedades dieléctricas de materiales de construcción mediante elipsometría

A set of measurements of electromagnetic properties of building materials is presented in this work. The method is based on the measurement of the polarization state of the reflected signal from the material under study at a fixed angle of incidence. From the measured data, by using the Fresnel equations, it has been obtained the dielectric constant. Measurements were done by using two horn antennas at the frequency of 9 GHz. The obtained results are compared with the free space reflexion and transmission Fresnel method and other reflection methods based on a conductor waveguide. The method explained in this work can be used for other type of materials and its main advantage is the non-destructive character and the ease implementation.

Estudio sobre la influencia del contenido de humedad de la madera en ensayos no destructivos para Pinus nigra Arn, Pinus radiata D. Don y Pinus sylvestris L.

El presente proyecto se centra en el estudio de la influencia que ejerce el contenido de humedad en la madera sobre mediciones realizadas mediante diversos ensayos no destructivos (NDT – Non Destructive Tests-). El objetivo es encontrar la relación entre el contenido de humedad de la madera de varias especies del género Pinus (Pinus nigra Arn, Pinus radiata D.Don. y Pinus sylvestris Ait.) y los resultados de diferentes NDT (penetrómetro, resistencia al arranque de tornillos y velocidad de propagación de ondas inducidas y ultrasonidos), y en caso de existir, tratar de elaborar un modelo o factor de corrección que nos permita tener en cuenta dicha influencia en futuros NDT.

Estudios de eficiencia en el uso de la luz y estimaciones de biomasa en cultivos energéticos de Salix sp. en Central New York, USA

La productividad es un factor importante que influye en la viabilidad económica de un cultivo energético de sauce y maximizarla se convierte en un tema primordial. Esta investigación está directamente relacionada con dicha característica. La productividad varía según los clones cultivados, que pueden ser mejorados y seleccionados genéticamente. Los programas genéticos requieren de una información previa (productividad media en función del porte y número de los tallos, características de las hojas, resistencia a las plagas, etc.) que ayudará a obtener clones más productivos y resistentes. Por ello, nuestra investigación consta de dos estudios: (1) Evaluación de la eficiencia del uso de la luz o LUE (Light Use Efficiency). El incremento de biomasa y la eficiencia del uso de la luz (LUE) fue estudiado en 15 clones del genero Salix durante los meses de junio a septiembre de 2011 en Belleville (Central New York, USA). Los objetivos de este estudio fueron: (1) Evaluar la eficiencia del uso de la luz en la explicación a la variación en la producción de biomasa y (2) Determinar si existen diferencias significativas entre clones evaluando el índice de área foliar (LAI) y algunos componentes de las hojas (N, P, K,…). Se concluye que la variación de biomasa está relacionada con la cantidad de luz interceptada y con la eficiencia de su uso. Dicha información debe de ser transferida para ayudar a mejorar genéticamente los futuros clones a comercializar, con el fin de maximizar la productividad y aumentar la resistencia a plagas. (2) Estimación de biomasa a través de modelos de regresión. Los estudios de investigación relacionados con la productividad requieren estimaciones no destructivas de la biomasa aérea. Sin embargo, el nivel de precisión requerido y la inversión de tiempo son excesivos para operaciones comerciales con grandes extensiones (plantaciones de 10.000 ha). Por esta razón, se estudia el nivel de especificidad (específico, intermedio y general) en la toma de datos de campo sobre los mismos 15 clones (12 de ellos se pueden agrupar en 5 grupos según su genotipo origen) del genero Salix, empleados en el estudio anterior. Para todos los niveles estudiados se observaron diferencias significativas. Pero desde nuestro punto de vista, las diferencias obtenidas no son relevantes. Para validar los modelos finalmente seleccionados se calcularon los porcentajes de error entre la biomasa estimada por los modelos de regresión calculados y la biomasa real obtenida tras los pesajes de biomasa, todo ello se realizó para cada clon según nivel de especificidad. ABSTRACT Productivity is an important factor in the economic viability of a willow crop´s, therefore, maximize it becomes a major factor. This study is directly related to this feature. Productivity, among other factors, may vary depending on different clones, which can be improved and selected genetically. Genetic programs require prior information (average productivity, size and number of stems, leaf characteristics, resistance to pests, etc.) to help you get more productive clones resistant to local pests. Our research consists of two studies: (1) Evaluation of the efficiency of use of light (LUE, Light Use Efficiency). The increase of biomass and light use efficiency (LUE) was tested on 15 clones of the genus Salix during June and September 2011 in Belleville (Central New York, USA). The objectives of this study were: (1) evaluate the light use efficiency and its relationship with the variation in biomass production and (2) determine whether there are significant differences between clones evaluating the leaf area index (LAI) and some traits of the leaves (N, P, K). We studied the correlation with the light use efficiency. It is concluded that the variation of biomass was related to the amount of light intercepted and its efficiency. Such information must be transferred to help improve future genetically clones to market in order to maximize productivity and increase resistance to pests. (2) Estimation of biomass through regression models. Research studies related to productivity estimates require precision and non destructive biomass. However, the level of accuracy required and the investment of time are excessive for large commercial operations with extensions (plantations of 10,000 ha). Precisely for this reason, we study the level of specificity (specific, intermediate and general) in making field data on the same 15 clones (12 of them can be grouped into five groups according to their genotype origin) of the genus Salix, employees in the previous study. For all levels studied some significant differences were observed. But from our practical standpoint, the differences are not relevant. Finally, to validate the selected models, we calculated the percent of bias between estimated biomass (by the regression models) and real biomass obtained after the weighing of biomass, all this process was done for each clone by level of specificity.

Clasificación de madera estructural de gran escuadría de Pinus sylvestris l. mediante métodos no destructivos

Esta Tesis Doctoral aborda el estudio de algunas técnicas no destructivas para la clasificación de madera de pino silvestre (Pinus sylvestris L.) de procedencia española y de gruesa escuadría para uso estructural. Para la estimación del módulo de elasticidad y de la resistencia se han aplicado técnicas basadas en la propagación de una onda a través de la madera: onda de ultrasonidos (Sylvatest) o de impacto (Microsecond Timer) en dirección longitudinal, o vibración en dirección longitudinal y transversal (PLG). Para la estimación de la densidad se han utilizado métodos puntuales basados en el penetrómetro (Pilodyn) y en la resistencia al arranque de un tornillo. Las variables obtenidas han sido relacionadas con los resultados de la clasificación visual y con las propiedades de la madera determinadas mediante ensayo mecánico. Además, se ha estudiado la influencia de la humedad de la madera en la velocidad de propagación de la onda para definir factores de corrección a los equipos comerciales utilizados en esta Tesis Doctoral. La muestra de estudio está formada por 244 piezas procedentes de El Espinar, Segovia, con dimensiones nominales 150 x 200 x 4000 mm (218 piezas) y 100 x 150 x 3000 mm (26 piezas). De todas las piezas se tomaron datos de dimensiones, contenido de humedad y clasificación visual según la norma UNE 56544. En las primeras 218 vigas se aplicaron las técnicas de ultrasonidos, onda de impacto y vibraciones, se determinó la densidad de cada pieza completa y se ensayaron según la norma UNE-EN 408 para obtener el módulo de elasticidad global (en todos los casos) y local (en un porcentaje), así como de la tensión de rotura. Se extrajeron tres rebanadas para los ensayos puntuales y para el cálculo de la densidad. En las otras 26 piezas se repitieron los ensayos (transmisión de onda, vibración y clasificación visual) durante el proceso de secado natural, desde que la madera se encontraba húmeda (en torno al 40 %) hasta la humedad de equilibrio higroscópico (en torno al 9%). Respecto a la clasificación visual no se han observado diferencias significativas entre la calidad MEG o las rechazadas. Se han estudiado las consecuencias del secado (principalmente las deformaciones) y no se ha encontrado justificación para que estos defectos penalicen la clasificación. Para la densidad, el mayor R2 obtenido ha sido de un 47% a partir del uso combinado de los dos equipos puntuales (penetrómetro y arranque de tornillo). Para el módulo de elasticidad y la tensión de rotura, la mejor relación se ha obtenido a partir de la técnica de vibración longitudinal, con unos coeficientes de 79% y un 52% respectivamente. Se ha estimado que el aumento de un punto porcentual en el contenido de humedad de la madera produce una pérdida de velocidad de onda del 0,58% para Sylvatest y Microsecond Timer, y del 0,71% para PLG. Estos valores son generalizables para un rango de humedades entre 9 y 25 %. Abstract This Doctoral Thesis approach the study of some non-destructive techniques as a classification method for structural use of Scots pine wood of Spanish origin with large cross section. To estimate the modulus of elasticity and strength have been used techniques based on the propagation of a wave through the timber: ultrasonic wave (Sylvatest) or stress wave (Microsecond Timer) in longitudinal direction, or vibration in longitudinal and transversal direction (PLG). Local probing methods have been applied to estimate the density, based on penetrometer (Pilodyn) and the screw withdrawal resistance meter. The different variables obtained were compared with the results of the visual grading and the values of the properties of the wood determined by the standardized test of the pieces. Furthermore, the influence of the moisture content of the wood on the velocity of propagation of the waves through the timber has been analyzed in order to establish a correction factor for the commercial devices used in this Doctoral Thesis. The sample tested consists of 244 pieces from El Espinar, Segovia, with nominal dimensions 150 x 200 x 4000 mm (218 pieces) and 100 x 150 x 3000 mm (26 pieces). Data collection about dimensions, moisture content and visual grading according to the UNE 56544 standard were carried out on all the pieces. The first 218 pieces were tested by non destructive techniques based on ultrasonic wave, stress wave and vibration, the density was measured on each piece and bending test according to the UNE-EN 408 standard was carried out for calculating the global modulus of elasticity (all the pieces) and the local one (only a representative group), as well as the bending strength. Three slices were removed for implementing the local probing and to calculate the density. In the other 26 pieces the tests (wave transmission, vibration and visual grading) were repeated during the natural drying process, from wet timber (around 40 % moisture content) up to the equilibrium moisture content (around 9%). Regarding the visual grading no significant differences were observed between MEG or rejected pieces. The effects of drying (deformations) have been studied, and justification for the specification hasn't been found. To estimate the density, the greater R2 obtained was 47% by using both penetrometer and screw withdrawal. For the modulus of elasticity and bending strength, the best relationship has been found with the longitudinal vibration, with coefficients of 79% and 52% respectively. It has been estimated that an increase of a point of the moisture content of the wood produces a decrease on the velocity obtained from ultrasonic or stress wave of 0,58%, and 0,71 % for the one obtained from vibration. Those values can be generalized for a range of moisture content from 9 to 25 %.

Application of photoreflectance to advanced multilayer structures for photovoltaics

Photoreflectance (PR) is a convenient characterization tool able to reveal optoelectronic properties of semiconductor materials and structures. It is a simple non-destructive and contactless technique which can be used in air at room temperature. We will present experimental results of the characterization carried out by means of PR on different types of advanced photovoltaic (PV) structures, including quantum-dot-based prototypes of intermediate band solar cells, quantum-well structures, highly mismatched alloys, and III?V-based multi-junction devices, thereby demonstrating the suitability of PR as a powerful diagnostic tool. Examples will be given to illustrate the value of this spectroscopic technique for PV including (i) the analysis of the PR spectra in search of critical points associated to absorption onsets; (ii) distinguishing signatures related to quantum confinement from those originating from delocalized band states; (iii) determining the intensity of the electric field related to built-in potentials at interfaces according to the Franz?Keldysh (FK) theory; and (v) determining the nature of different oscillatory PR signals among those ascribed to FK-oscillations, interferometric and photorefractive effects. The aim is to attract the interest of researchers in the field of PV to modulation spectroscopies, as they can be helpful in the analysis of their devices.

Relationship between solar radiation on watercore on apple fruit assessed with MRI

This work is a preliminary studio of the possibility of assess a relationship between solar radiation and watercore development on apple fruit, during maturation, using a non destructive method such as Magnetic Resonance Imaging (MRI). For such purpose, several low cost solar radiation sensors were designed for the trial and placed at 2 different heights (1.5 and 2.5 m) on 6 adult ?Esperiega? apple trees, in a commercial orchard in Ademuz (Valencia). Sensors were connected along 27 days, during the end of the growth period and start of the fruit maturation process, and radiation measurements of the a-Si sensors were recorded every 1 minute. At the end of this period, fruits from the upper and the lower part of the canopy of each tree were harvested. In all, 152 apples were collected and images with MRI. A Principal Component Analysis, perfomed over the histograms of the images, as well as segmentation methods were performed on the MR images in order to find a pattern involving solar radiation and watercore incidence.

Assessment of watercore development in apples with MRI: Effect offruit location in the canopy

tWatercore distribution inside apple fruit (block or radial), and its incidence (% of tissue) were relatedto the effect of solar radiation inside the canopy as measured by a set of low-cost irradiation sensors.221 samples were harvested in two seasons from the top and the bottom of the canopy and submittedto the non-invasive and non-destructive technique of magnetic resonance imaging (MRI) in order toobtain 20 inner tomography slices from each fruit and analyze the damaged areas using an interactive3D segmentation method. The number of fruit corresponding to each type of damage and the relevantpercentage were calculated and it was found that apples from the top of the tree were mainly of the radialtype (84%) and had more watercore (approx. 5% more) than apples from the bottom (65% radial). From theimage segmentation, the Euler number, a morphometric parameter, was extracted from the segmentedimages and related to the type of watercore symptoms. Apples with block watercore were grouped inEuler numbers between −400 and 400 with a small evolution. For apples with radial development, theEuler number was highly negative: up to −1439. Significant differences were also found regarding sugarcomposition, with higher fructose and total sugar contents in apples from the upper canopy, compared tothose in the lower canopy location. In the seasons studied (2011 and 2012), significantly higher sorbitoland lower sucrose and fructose contents were found in watercore-affected tissue compared to the healthytissue of affected apples and also compared to healthy apples.

Effect of impacting radius of curvature on firmness sensing of fruits in a sorting system.

Fruits of two varieties of both apples and pear were tested to measure their response to small energy impact applied by a impact tester with two spherical tips of different radious of curvature ( RA = 2.48 cm and RB = 0.98 cm) and equal mass were used. In the four varieties studied, the size of bruise was smaller with a spherical tip RA than with tip RB . The non-destructive impact test would cause less damage with a spherical impactor with a radious bigger than 0.98 cm.

Mealiness assessment in fruits using MRI techniques.

Mealiness is a sensory attribute that cannot be defined by a single parameter but through a combination of variables (multidimensional structure). Previous studies propose the definition of mealiness as the lack of crispiness, of hardness and of juiciness. Current aims are focused on establishing non destructive tests for mealiness assessment. MultiSliceMultiEcho Magnetic resonance images (MRI, 64*64pixels) have been taken corresponding to a 3ms of Echo time. Small samples of Top Red apples stored 6 months at controlled atmosphere (expected to be non mealy) and 2°C (expected to be mealy) have been used for MRI imaging. Three out of four apples corresponding to the sample maintained at controlled atmosphere did not develop mealiness while three out of four fruits corresponding to the sample stored at 2°C became mealy after 6 month of storage. The minimum T2 values/image obtained for the mealy apples shows to be significantly lower when compared with non mealy apples pointing that a more dis-aggregated structure leads to a quicker loss of signal Also, there is a significant linear correlation (r=-0.76) between the number of pixels with a T2 value below 35ms within a fruit image and the deformation parameter registered during the Magness-Taylor firmness test. Finally, all the T2 images of the mealy apples show a regional variation of contrast which is not shown for non mealy apples. This variation of contrast is similar to the MRI images of water-cored apples indicating that in these cases there is a differential water movement that may precede the internal browning.

New version of a laboratory impact device for firmness sensing of fruits.

Results of previous studies conducted by different researchers have shown that impact techniques can be used to evaluate firmness (Delwiche et al., 1989; Delwiche et al.;1996; Jaren et al., 1992; Ruiz Altisent et al., 1996). To impact the fruit with a small spherical impactor of known mass and radius of curvature and measure the acceleration of the impactor is a technique described by Chen et al. (1985) and used by several researchers for sensing fruit firmness (Jaren et al., 1992; Correa et al.; 1992). The advantages of this method vs. a force sensor that measures the force as a function of time is that the measured impact-acceleration response is independent of the fruit mass and is less sensitive to the variation in the radius of curvature of the fruit (Chen et al., 1996). Ruiz Altisent et al. (1993) developed and used a 50 g impactor with a 19 mm diameter spherical tip, dropping from different height for fruits (apples, pears, avocados, melons, peaches ...). Another impact device for firmness sensing of fruits was developed by Chen and Ruiz Altisent (1996). They designed and fabricated an experimental low-mass impact sensor for high-speed sensing of fruit firmness. The impactor consisted of a semi-spherical impacting tip attached to the end (near the centre of percussion) of a pivoting arm. Impact is done by swinging the impactor to collide with the fruit. It has been implemented for on-line use. In both devices a small accelerometer is mounted behind the impacting tip. Lateral impactor and vertical impactor have been used in laboratory and the results from non-destructive impact tests have contributed to standardise methods to measure fruit firmness: Barreiro (1992) compared impact parameters and results of Magness-Taylor penetration tests for apples, pears, apricots [and peaches; Agulheiro (1994) studied the behaviour of the impact parameters during seven weeks of cold storage of two melon varieties; Ortiz (1998) used low energy impact and NIR procedures to segregate non crispy, non firm and soft peaches. Steinmetz (1996) compared various non-destructive firmness sensors, based on sound, impact and micro-deformation.

Remote sensing of LAI, chlorophyll and leaf nitrogen pools of crop- and grasslands in five European landscapes.

Leaf nitrogen and leaf surface area influence the exchange of gases between terrestrial ecosystems and the atmosphere, and play a significant role in the global cycles of carbon, nitrogen and water. The purpose of this study is to use field-based and satellite remote-sensing-based methods to assess leaf nitrogen pools in five diverse European agricultural landscapes located in Denmark, Scotland (United Kingdom), Poland, the Netherlands and Italy. REGFLEC (REGularized canopy reFLECtance) is an advanced image-based inverse canopy radiative transfer modelling system which has shown proficiency for regional mapping of leaf area index (LAI) and leaf chlorophyll (CHLl) using remote sensing data. In this study, high spatial resolution (10–20 m) remote sensing images acquired from the multispectral sensors aboard the SPOT (Satellite For Observation of Earth) satellites were used to assess the capability of REGFLEC for mapping spatial variations in LAI, CHLland the relation to leaf nitrogen (Nl) data in five diverse European agricultural landscapes. REGFLEC is based on physical laws and includes an automatic model parameterization scheme which makes the tool independent of field data for model calibration. In this study, REGFLEC performance was evaluated using LAI measurements and non-destructive measurements (using a SPAD meter) of leaf-scale CHLl and Nl concentrations in 93 fields representing crop- and grasslands of the five landscapes. Furthermore, empirical relationships between field measurements (LAI, CHLl and Nl and five spectral vegetation indices (the Normalized Difference Vegetation Index, the Simple Ratio, the Enhanced Vegetation Index-2, the Green Normalized Difference Vegetation Index, and the green chlorophyll index) were used to assess field data coherence and to serve as a comparison basis for assessing REGFLEC model performance. The field measurements showed strong vertical CHLl gradient profiles in 26% of fields which affected REGFLEC performance as well as the relationships between spectral vegetation indices (SVIs) and field measurements. When the range of surface types increased, the REGFLEC results were in better agreement with field data than the empirical SVI regression models. Selecting only homogeneous canopies with uniform CHLl distributions as reference data for evaluation, REGFLEC was able to explain 69% of LAI observations (rmse = 0.76), 46% of measured canopy chlorophyll contents (rmse = 719 mg m−2) and 51% of measured canopy nitrogen contents (rmse = 2.7 g m−2). Better results were obtained for individual landscapes, except for Italy, where REGFLEC performed poorly due to a lack of dense vegetation canopies at the time of satellite recording. Presence of vegetation is needed to parameterize the REGFLEC model. Combining REGFLEC- and SVI-based model results to minimize errors for a "snap-shot" assessment of total leaf nitrogen pools in the five landscapes, results varied from 0.6 to 4.0 t km−2. Differences in leaf nitrogen pools between landscapes are attributed to seasonal variations, extents of agricultural area, species variations, and spatial variations in nutrient availability. In order to facilitate a substantial assessment of variations in Nl pools and their relation to landscape based nitrogen and carbon cycling processes, time series of satellite data are needed. The upcoming Sentinel-2 satellite mission will provide new multiple narrowband data opportunities at high spatio-temporal resolution which are expected to further improve remote sensing capabilities for mapping LAI, CHLl and Nl.

Estudio metrológico de un sensor de impacto no destructivo para la determinación de firmeza de frutas en líneas de confección.

A non destructive impact sensor to measure fruit firmness has been installed on the sizer chain of an experimental fruit packing line. The sensor measures the fruit firmness related to the acceleration-time curve supplied by an accelerometer attached to an impacting arm. The sensor works correctly at a speed of 5 to 7 fruits per second. Ratio A/t (maximum acceleration value divided by its corresponding time), mean, and maximum slopes of the curves supplied by the accelerometer, were well correlated with the firmness data obtained in laboratory with the load-unload test. The accelerometer signal allows the classification of the fruit in three levels of firmness, by means of a specific software.

Integrated studies for the evaluation of conservation treatments on buildings materials from archaeological sites: application to the case of Merida (Spain)

The application of conservation treatments, such as consolidation and protection ones, has been demonstrated ineffective in many cases, and even harmful. Evaluation studies should be a mandatory task, ideally before and after the intervention, but both tasks are complex and unusual in the case of archaeological heritage. This study is mainly focused on analyzing changes in petrophysical properties of stone material from archaeological sites of Merida (Spain), evaluating, both on site and in laboratory, effects derived from different conservation treatments applied in past interventions, throughout the integration of different non-destructive techniques (NDT) and portable devices of analysis available at the Institute of Geosciences (CSIC,UCM). These techniques allow, not only assessment of effectiveness and alteration processes, but also monitoring durability of treatments, focused mainly on 1996 intervention in the case of Roman Theater, as well as different punctual interventions from the 90?s until date in the House of Mitreo. Studies carried out on archaeological sites of Merida permit us to compare outcomes and also check limitations in the use of those equipments. In this paper we discuss about the use of some techniques, their integration and limits, for the assessment of conservation treatments, showing some examples of Merida?s case study.

Comparison of different pre-treatments to improve accuracy of total soluble solids.

The applicability of a portable NIR spectrometer for estimating the °Brix content of grapes by non-destructive measurement has been analysed in field. The NIR spectrometer AOTF-NIR Luminar 5030, from Brimrose, was used. The spectrometer worked with a spectral range from 1100 to 2300 nm. A total of 600 samples of Cabernet Sauvignon grapes, belonging to two vintages, were measured in a non-destructive way. The specific objective of this research is to analyse the influence of the statistical treatment of the spectra information in the development of °Brix estimation models. Different data pretreatments have been tested before applying multivariate analysis techniques to generate estimation models. The calibration using PLS regression applied to spectra data pretreated with the MSC method (multiplicative scatter correction) has been the procedure with better results. Considering the models developed with data corresponding to the first campaign, errors near to 1.35 °Brix for calibration (SEC = 1.36) and, about 1.50 °Brix for validation (SECV = 1.52) were obtained. The coefficients of determination were R2 = 0.78 for the calibration, and R2 = 0.77 for the validation. In addition, the great variability in the data of the °Brix content for the tested plots was analysed. The variation of °Brix on the plots was up to 4 °Brix, for all varieties. This deviation was always superior to the calculated errors in the generated models. Therefore, the generated models can be considered to be valid for its application in field. Models were validated with data corresponding to the second campaign. In this sense, the validation results were worse than those obtained in the first campaign. It is possible to conclude in the need to realize an adjustment of the spectrometer for each season, and to develop specific predictive models for every vineyard.

Propiedades de materiales mediante análisis de radiación aleatoria

Las técnicas de speckle tienen un gran interés científico e ingenieril, ya que son métodos de ejecución rápida y no destructiva, con base en el análisis de las fluctuaciones de intensidad de la radiación producida cuando la luz coherente de un haz láser es esparcida por un material dado. En este caso se produce un patrón aleatorio de interferencia y difracción donde la suma de las componentes desfasadas dará lugar a máximos y mínimos de intensidad en distintos puntos del espacio. Éste, pese a tratarse de un ruido nocivo en multitud de áreas tales como la transmisión de señales o la holografía, tiene importantes propiedades físicas que lo caracterizan y lo hacen útil como medio para analizar sistemas reales de muy diversa índole. En el presente estudio, se ha llevado a cabo un análisis polarimétrico de la radiación aleatoria esparcida por una serie de muestras metálicas y dieléctricas con el objetivo de establecer una base comparativa que nos permita poder distinguir unas de otras. Para este fin se han comparado los parámetros de polarización de Stokes, el grado de polarización de la luz, las distribuciones de intensidad y el tamaño medio del speckle registrado en los distintos patrones de intensidad. Además, se analizará la dependencia de la rugosidad en el grado de polarización de la luz para los distintos medios sometidos a estudio. Abstract Speckle techniques have a great scientific and engineering interest as they are methods of rapid and non-destructive execution, based on the analysis of the fluctuations of intensity of the radiation produced when coherent light of a laser beam is scattered by a material given. In this case, a random pattern of interference and diffraction occurs where the sum of phase shifted components will result in maximum or minimum of intensity at different points in space. This, despite being a harmful noise in many areas such as signal transmission or holography, has important physical properties that characterize it and make it useful as a means to analyze real systems of various kinds. In the present study, we have conducted a polarimetric analysis of the random radiation scattered by a series of metal and dielectric samples in order to establish a comparative basis to allow us to distinguish one from another. To this end we have compared, the stokes polarization parameters, the degree of polarization (DOP), the intensity distributions and the average size of the speckle registered in the different intensity patterns. Furthermore, dependence of roughness in the DOP of light for the different means under study will be analyzed.