An overview of integrated pest management (IPM) in north-eastern Australian grain farming systems: Past, present and future prospects

The authors overview integrated pest management (IPM) in grain crops in north-eastern Australia, which is defined as the area north of latitude 32°S. Major grain crops in this region include the coarse grains (winter and summer cereals), oilseeds and pulses. IPM in these systems is complicated by the diversity of crops, pests, market requirements and cropping environments. In general, the pulse crops are at greatest risk, followed by oilseeds and then by cereal grains. Insecticides remain a key grain pest management tool in north-eastern Australia. IPM in grain crops has benefited considerably through the increased adoption of new, more selective insecticides and biopesticides for many caterpillar pests, in particular Helicoverpa spp. and loopers, and the identification of pest-crop scenarios where spraying is unnecessary (e.g. for most Creontiades spp. populations in soybeans). This has favoured the conservation of natural enemies in north-eastern Australia grain crops, and has arguably assisted in the management of silverleaf whitefly in soybeans in coastal Queensland. However, control of sucking pests and podborers such as Maruca vitrata remains a major challenge for IPM in summer pulses. Because these crops have very low pest-damage tolerances and thresholds, intervention with disruptive insecticides is frequently required, particularly during podfill. The threat posed by silverleaf whitefly demands ongoing multi-pest IPM research, development and extension as this pest can flare under favourable seasonal conditions, especially where disruptive insecticides are used injudiciously. The strong links between researchers and industry have facilitated the adoption of IPM practices in north-eastern Australia and augers well for future pest challenges and for the development and promotion of new and improved IPM tactics.

Factors related to seat belt use : A Turkish case

Seat belts are effective safety devices used to protect car occupants from severe injuries and fatalities during road vehicle accidents. Despite the proven effectiveness of seat belts, seat belt use rates are quite low, especially in developing countries, such as Turkey. The general aim of the present study was to investigate a large variety of factors related to seat belt use among Turkish car occupants using different perspectives and methods and therefore, to contribute to the design of effective seat belt use interventions for increasing seat belt use rates in Turkey. Five sub-studies were conducted within the present study. In the first sub-study, environmental (e.g., road type) and psycho-social factors (e.g., belt use by other car occupants) related to the seat belt use of front-seat occupants were investigated using observation techniques. Being male, of a young age, and traveling on city roads were the main factors negatively related to seat belt use. Furthermore, seat belt use by the drivers and front-seat passengers was highly correlated and a significant predictors of each other. In the second sub-study, the motivations of the car occupants for seat belt use and non-use were investigated using interview techniques. Situational conditions, such as traveling on city roads and for short distances, and not believing in the effectiveness and relevance of seat belt use for safety, were the most frequently reported reasons for not using a seat belt. Safety, habit and avoiding punishment were among the most frequently reported reasons for using a seat belt. In the third sub-study, the Theory of Planned Behavior (TPB) and the Health Belief Model (HBM) were applied to seat belt use using Structural Equation Modeling techniques. The TPB model showed a good fit to the data, whereas the HBM showed a poor fit to the data. Within the TPB model, attitude and subjective norm were significant predictors of intentions to use a seat belt on both urban and rural roads. In the fourth sub-study, seat belt use frequency and motivations for seat belt use among taxi drivers were investigated and compared between free-time and work-time driving using a survey. The results showed that taxi drivers used seat belts more when driving a private car in their free-times compared to when driving a taxi during their work-times. The lack of a legal obligation to use a seat belt in city traffic and fear of being attacked or robbed by the passengers were found as two specific reasons for not using a seat belt when driving a taxi. Lastly, in the fifth sub-study, the relationship of seat belt use to driver and health behaviors was investigated using a survey. Although seat belt use was related both to health and driver behaviors, factor analysis results showed that it grouped with driver behaviors. Based on the results of the sub-studies, a tentative empirical model showing different predictors of seat belt use was proposed. According to the model, safety and normative motivations and perceived physical barriers related to seat belt use are the three important predictors of seat belt use. Keywords: Seat belt use; environmental factors; psycho-social factors; safety and normative motivations; the Theory of Planned Behavior; the Health Belief Model; health behaviors; driver behaviors; front-seat occupants; taxi drivers; Turkey.

Visual completion in an illusory figure

The visual systems of humans and animals represent physical reality in a modified way, depending on the specific demands that the species in question has for survival. The ability to perceive visual illusions is found in independently evolved visual systems, from honeybees to humans. In humans, the ability emerges early, at the age of four months. Thus the perception of illusion is likely to reflect visual processes of fundamental importance for object perception in natural vision. The experiments reported in this thesis employed various modifications of the Kanizsa triangle, a drawn configuration composed of three black disks with missing sectors on a white background. The sectors appear to form the tips of a triangle. The visual system completes the physically empty area between the disks, generally called inducers, with giving the perception of an illusory triangle. The illusory triangle consists of an illusory surface bounded by illusory contours; the triangle appears brighter than and to lie above the background. If the sectors are coloured, the colour fills the illusory area, a phenomenon known as neon colour spreading . We investigated spatial limitations on the perception of Kanizsa-type illusions and how other stimuli and viewing parameters affected these limitations. We also studied complex configurations thick, bent, mobile and chromatic inducers - to determine whether illusions combining several attributes can be perceived. The results suggest that the visual system is highly effective in completing a percept. The perception of an illusory figure is spatially scale invariant when perceived at threshold. The processing time and the number of fixations modify the percept, making the perception of the illusion more probable in various viewing conditions. Furthermore, the fact that the illusion can be perceived when only one inducer is physically present at any given moment indicates the potential of single inducers. Apparently, modelling illusory figure perception will require a combination of low-level, local processes and higher-level integrative processes. Our studies with stimuli combining several attributes relevant to object perception demonstrate that the perception of an illusory figure is flexible and is maintained also when it contains colour and volume and when shown in movement. All in all, the results confirm the assumed importance of the visual processes related with the perception of illusory figures in everyday viewing. This is indicated by the variety of inducer modifications that can be made without destroying the percept. Furthermore, the illusion can acquire additional attributes from such modifications. Due to individual differences in the perception of illusory figures, universal values for absolute performance are not always meaningful, but stable trends and general relations do exist.

Healthcare users’ experiences of communicating with healthcare professionals about children who have life-limiting conditions: A qualitative systematic review protocol

REVIEW QUESTION / OBJECTIVE The objective of this review is to identify and synthesize the best international qualitative evidence on healthcare users’ experiences of communication with healthcare professionals about children who have life-limiting conditions. For the purposes of this review, “healthcare users” will be taken to include children who have life-limiting conditions and their families. The question to be addressed is: - What are healthcare users’ experiences of communicating with healthcare professionals about children who have life-limiting conditions? INCLUSION CRITERIA - Types of participants: This review will consider all qualitative studies that focus on users of healthcare services for children who have life-limiting conditions. These users are anticipated to include children who have a life-limiting condition and their family members. In instances where children are not under the legal care of one or both parents, service users may also include other types of legal guardians. - Phenomena of interest: This review will consider experiences of communicating with healthcare professionals about children who have life-limiting conditions. - Context: This review will consider studies relating to communication with healthcare professionals about children who have a life-limiting condition, irrespective of whether the healthcare service is based in a hospital, hospice, or community setting. There is no restriction on the country in which a study was conducted.

Oppimisen kohteen ja oppijan vastavuoroinen kehitys : Teleyrityksen asiakaspalvelun työyhteisöjen oppimiskäytäntöjen uudistaminen osana teknologis-taloudellista kumousta

Reciprocal development of the object and subject of learning. The renewal of the learning practices of front-line communities in a telecommunications company as part of the techno-economical paradigm change. Current changes in production have been seen as an indication of a shift from the techno-economical paradigm of a mass-production era to a new paradigm of the information and communication technological era. The rise of knowledge management in the late 1990s can be seen as one aspect of this paradigm shift, as knowledge creation and customer responsiveness were recognized as the prime factors in business competition. However, paradoxical conceptions concerning learning and agency have been presented in the discussion of knowledge management. One prevalent notion in the literature is that learning is based on individuals’ voluntary actions and this has now become incompatible with the growing interest in knowledge-management systems. Furthermore, commonly held view of learning as a general process that is independent of the object of learning contradicts the observation that the current need for new knowledge and new competences are caused by ongoing techno-economic changes. Even though the current view acknowledges that individuals and communities have key roles in knowledge creation, this conception defies the idea of the individuals’ and communities’ agency in developing the practices through which they learn. This research therefore presents a new theoretical interpretation of learning and agency based on Cultural-Historical Activity Theory. This approach overcomes the paradoxes in knowledge-management theory and offers means for understanding and analyzing changes in the ways of learning within work communities. This research is also an evaluation of the Competence-Laboratory method which was developed as part of the study as a special application of Developmental Work Research methodology. The research data comprises the videotaped competence-laboratory processes of four front-line work communities in a telecommunications company. The findings reported in the five articles included in this thesis are based on the analyses of this data. The new theoretical interpretation offered here is based on the assessment that the findings reported in the articles represent one of the front lines of the ongoing historical transformation of work-related learning since the research site represents one of the key industries of the new “knowledge society”. The research can be characterized as elaboration of a hypothesis concerning the development of work related learning. According to the new theoretical interpretation, the object of activity is also the object of distributed learning in work communities. The historical socialization of production has increased the number of actors involved in an activity, which has also increased the number of mutual interdependencies as well as the need for communication. Learning practices and organizational systems of learning are historically developed forms of distributed learning mediated by specific forms of division of labor, specific tools, and specific rules. However, the learning practices of the mass production era become increasingly inadequate to accommodate the conditions in the new economy. This was manifested in the front-line work communities in the research site as an aggravating contradiction between the new objects of learning and the prevailing learning practices. The constituent element of this new theoretical interpretation is the idea of a work community’s learning as part of its collaborative mastery of the developing business activity. The development of the business activity is at the same time a practical and an epistemic object for the community. This kind of changing object cannot be mastered by using learning practices designed for the stable conditions of mass production, because learning has to change along the changes in business. According to the model introduced in this thesis, the transformation of learning proceeds through specific stages: predefined learning tasks are first transformed into learning through re-conceptualizing the object of the activity and of the joint learning and then, as the new object becomes stabilized, into the creation of new kinds of learning practices to master the re-defined object of the activity. This transformation of the form of learning is realized through a stepwise expansion of the work community’s agency. To summarize, the conceptual model developed in this study sets the tool-mediated co-development of the subject and the object of learning as the theoretical starting point for developing new, second-generation knowledge management methods. Key words: knowledge management, learning practice, organizational system of learning, agency

Odour sampling 1: Physical chemistry considerations

The selection of an odour sampling device may influence the composition of the resulting odour sample. Limited comparison of emission rates derived from turbulent and essentially quiescent sampling devices confirms that the emission rates derived from these devices are quite different. There is therefore compelling evidence that current odour sampling practice should have greater regard for fundamental physical and chemical principles, the nature of the odour source and the conditions created by the sampling device. Such consideration may identify the most appropriate situations under which the use of these devices may or may not be correct.

Habitat dynamics in the bed sediments of an intermittent upland stream

The effects of the hydrological regime on temporal changes to physical characteristics of substratum habitat, sediment texture of surface sediments (<10 cm), were investigated in a sub-tropical headwater stream over four years. Surface discharge was measured together with vertical hydraulic gradient and groundwater depth in order to explore features of sediment habitat that extend beyond the streambed surface. Whilst the typical discharge pattern was one of intermittent base flows and infrequent flow events associated with monsoonal rain patterns, the study period also encompassed a drought and a one-in-a-hundred-year flood. Rainfall and discharge did not necessarily reflect the actual conditions in the stream. Although surface waters were persistent long after discharge ceased, the streambed was completely dry on several occasions. Shallow groundwater was present at variable depths throughout the study period, being absent only at the height of the drought. The streambed sediments were mainly gravels, sand and clay. Finer sediment fractions showed a marked change in grain size over time, although bedload movement was limited to a single high discharge event. In response to a low discharge regimen (drought), sediments characteristically showed non-normal distributions and were dominated by finer materials. A high-energy discharge event produced a coarsening of sands and a diminished clay fraction in the streambed. Particulate organic matter from sediments showed trends of build-up and decline with the high and low discharge regimes, respectively. Within the surface sediment intersticies three potential categories of invertebrate habitat were recognised, each with dynamic spatial and temporal boundaries.

Assessment of permeable covers for odour reduction in piggery effluent ponds. 2. Field-scale trials

The efficacy of supported covers was investigated under field conditions using a series of prototypes deployed on an anaerobic pond treating typical piggery waste. Research focused on identifying effective cover support materials and deployment methods, quantifying odour reduction, and estimating the life expectancy of various permeable cover materials. Over a 10-month period, median odour emission rates were five to eight times lower from supported straw cover surfaces and a non-woven, spun fibre polypropylene weed control material than from the adjacent uncovered pond surface. While the straw covers visually appeared to degrade very rapidly, they continued to reduce odour emissions effectively. The polypropylene cover appeared to offer advantages from the perspectives of cost, reduced maintenance and ease of manufacture.

Survey of dental clinic patients: Smoking and preferences for cessation support

Background: Smoking cessation interventions delivered by dental practitioners can be as effective as those delivered by general medical practitioners. However, concern that addressing smoking may cause offence to their patients is a reason cited by dental practitioners for not regularly addressing patient smoking behaviours, despite believing they should play a role in smoking cessation. This study aimed to elicit the smoking behaviour and smoking cessation preferences of dental patients to determine if these concerns accurately reflect patient attitudes. Methods: We surveyed 726 adult dental patients attending the University of Queensland’s School of Dentistry Dental Clinics, Brisbane Dental Hospital, and four private dental practices in South East Queensland. Results: Most (80%) current daily smokers had tried to quit smoking. Smokers and non-smokers both agreed that dentists should screen for smoking behaviour and are qualified to offer smoking cessation advice (99% and 96% respectively). Almost all participants (96%) said they would be comfortable with their dentist asking about their smoking and that if their smoking was affecting their oral health their dentist should advise them to quit. Conclusions: Patients are receptive to dental practitioners inquiring about smoking behaviour and offering advice on quitting. Smoking patients showed considerable motivation and interest in quitting smoking, particularly in the context of health problems related to smoking being identified. These results should encourage dentists to raise the issue with their patients.

Systematic analysis of changes in cannabis use among participants in control conditions of randomised controlled trials

Introduction Cannabis remains the most used illegal substance across the globe, and negative outcomes and disorders are common. A spotlight therefore falls on reductions in cannabis use in people with cannabis use disorder. Current estimates of unassisted cessation or reduction in cannabis use rely on community surveys, and few studies focus on individuals with disorder. A key interest of services and researchers is to estimate effect size of reductions in consumption among treatment seekers who do not obtain treatment. Effects within waiting list or information-only control conditions of randomised controlled trials offer an opportunity to study this question. Method This paper examines the extent of reductions in days of cannabis use in the control groups of randomised controlled trials on treatment of cannabis use disorders. A systematic literature search was performed to identify trials that reported days of cannabis use in the previous 30 (or equivalent). Results Since all but one of the eight identified studies had delayed treatment controls, results could only be summarised across 2–4 months. Average weighted days of use in the previous 30 days fell from 24.5 to 19.9, and a meta-analysis using a random effects model showed an average reduction of 0.442 SD. However, every study had at least one significant methodological issue. Conclusions While further high-quality data is needed to confirm the observed effects, these results provide a baseline from which researchers and practitioners can estimate the extent of change required to detect effects of cannabis treatments in services or treatment trials.

Evaluation of a remote drafting system for regulating sheep access to supplement

Remote drafting technology now available for sheep makes possible targeted supplementation of individuals within a grazing flock. This system was evaluated by using 68 Merino wethers grazing dry-season, native Mitchell grass pasture (predominantly Astrebla spp.) as a group and receiving access to lupin grain through a remote drafter 0, 1, 2, 4 or 7 days/week for 8 weeks. The sole paddock watering point was separately fenced and access was via a one-way flow gate. Sheep exited the watering point through a remote drafter operated by solar power and were drafted by radio frequency identification (RFID) tag, according to treatment, either back into the paddock or into a common supplement yard where lupins were provided ad libitum in a self-feeder. Sheep were drafted into the supplement yard on only their first time through the drafter during the prescribed 24-h period and exited the supplement yard via one-way flow gates in their own time. The remote drafter operated with a high accuracy, with only 2.1% incorrect drafts recorded during the experimental period out of a total of 7027 sheep passes through the remote drafter. The actual number of accesses to supplement for each treatment group, in order, were generally less than that intended, i.e. 0.02, 0.69, 1.98, 3.35 and 6.04 days/week. Deviations from the intended number of accesses to supplement were mainly due to sheep not coming through to water on their allocated day of treatment access, although some instances were due to incorrect drafts. There was a non-linear response in growth rate to increased frequency of access to lupins with the growth rate response plateauing at similar to 3 actual accesses per week, corresponding to a growth rate of 72.5 g/head. day. This experiment has demonstrated the application of the remote drafting supplementation system for the first time under grazing conditions and with the drafter operated completely from solar power. The experiment demonstrates a growth response to increasing frequency of access to supplement and provides a starting point with which to begin to develop feeding strategies to achieve sheep weight-change targets.

The relationship between the determinants of rental housing satisfaction and considering moving in Finland

Purpose The purpose of this paper is to discuss the relation between dissatisfaction with housing conditions and considering moving among residents of Finnish rental multifamily buildings. The paper examines physical attributes, socioeconomic factors, and subjective opinions related to housing conditions and satisfaction with housing. Design/methodology/approach Logistic regression analysis is used to examine survey data to analyse which factors contribute to dissatisfaction with the housing unit and the apartment building and whether dissatisfaction is related to consideration of moving. Findings The findings indicate that dissatisfaction with the building and individual housing unit are associated with greater probability of considering moving. Satisfaction with kitchen, living room, storage, and building age are the most important indicators of satisfaction with the housing unit, and satisfaction with living room, bathroom, storage, and building age are associated with satisfaction with the apartment building. These are the areas in which landlords could invest in renovations to increase satisfaction in an attempt to reduce turnover. Research limitations/implications The study is conducted with Finnish data only. The sample is not a representative sample of the Finnish population. A longitudinal study would be needed to determine whether dissatisfied residents indending to move actually change residence. Originality/value This study is the first of its kind in the Finnish housing market. It tests a general model that has been suggested to be customized to local conditions. In addition, much of the research on this topic is more than 20 years old. Examination of the model under current housing and socioeconomic conditions is necessary to determine if relationships have changed over time.

Development and testing of an evaluation procedure for commercial manure additive products.

Manure additive products can be used to reduce odour emissions (OE) from livestock farms. The standardised evaluation of these manure additive products under specific farm conditions is important. In this study, the efficacy of a manure additive (WonderTreat(TM), CKLS, Inc., Hong-Kong) was assessed under Australian conditions utilising a combination of laboratory and field-scale evaluation techniques. As a first step, the efficacy of the manure additive was assessed in a laboratory-scale trial using a series of uniformly managed digesters and standard odour, liquor ammonia and hydrogen sulphide concentration measurement procedures. This showed that the addition of WonderTreat(TM) at the 'low dose rate' (LDR) (102.6 g m-2) used during the trial significantly, but only marginally (30%; P = 0.02) reduced the OE rate (mean 13.9 OU m-2 s-1) of anaerobic pig liquor relative to an untreated control (UC) (19.9 OU m-2 s-1). However, the 'high dose rate' (HDR) (205.3 g m-2) also assessed during the trial preformed similarly (19.7 OU m-2 s-1) to the UC. No statistically significant difference in the concentrations of a range of measured water quality variables at the 5% level was observed between the treatments or controls digesters. As a second step, a field-scale assessment of the manure additive was undertaken at a commercial piggery. Two piggery manure lagoons (each with approximately 2500 m2 surface area) were included in the study; one was treated with WonderTreat(TM) while the other was used as control. The efficacy of the treatment was assessed using olfactometric evaluation of odour samples collected from the surface of the pond using a dynamic wind tunnel and ancillary equipment. No statistically significant reduction in OE rate could be demonstrated (P = 0.35), partially due to the limited number of samples taken during the assessment. However, there was a numerical reduction in the average OE rate of the treatment pond (29 OU m-2 s-1 at 1 m s-1) compared to the control lagoon (38 OU m-2 s-1 at 1 m s-1).

Heat transfer with solid liquid phase change initiating at a point in a semi infinite mold

Short-time analytical solutions of temperature and moving boundary in two-dimensional two-phase freezing due to a cold spot are presented in this paper. The melt occupies a semi-infinite region. Although the method of solution is valid for various other types of boundary conditions, the results in this paper are given only for the prescribed flux boundary conditions which could be space and time dependent. The freezing front propagations along the interior of the melt region exhibit well known behaviours but the propagations along the surface are of new type. The freezing front always depends on material parameters. Several interesting results can be obtained as particular cases of the general results.

Inter-seasonal population dynamics and pest status of Bemisia tabaci (Gennadius) biotype B in an Australian cropping system

Bemisia tabaci, biotype B, commonly known as the silverleaf whitefly (SLW) is an alien species that invaded Australia in the mid-90s. This paper reports on the invasion ecology of SLW and the factors that are likely to have contributed to the first outbreak of this major pest in an Australian cotton cropping system, population dynamics of SLW within whitefly-susceptible crop (cotton and cucurbit) and non-crop vegetation (sowthistle, Sonchus spp.) components of the cropping system were investigated over four consecutive growing seasons (September-June) 2001/02-2004/05 in the Emerald Irrigation Area (EIA) of Queensland, Australia. Based on fixed geo-referenced sampling sites, variation in spatial and temporal abundance of SLW within each system component was quantified to provide baseline data for the development of ecologically sustainable pest management strategies. Parasitism of large (3rd and 4th instars) SLW nymphs by native aphelinid wasps was quantified to determine the potential for natural control of SLW populations. Following the initial outbreak in 2001/02, SLW abundance declined and stabilised over the next three seasons. The population dynamics of SLW is characterised by inter-seasonal population cycling between the non-crop (weed) and cotton components of the EIA cropping system. Cotton was the largest sink for and source of SLW during the study period. Over-wintering populations dispersed from weed host plant sources to cotton in spring followed by a reverse dispersal in late summer and autumn to broad-leaved crops and weeds. A basic spatial source-sink analysis showed that SLW adult and nymph densities were higher in cotton fields that were closer to over-wintering weed sources throughout spring than in fields that were further away. Cucurbit fields were not significant sources of SLW and did not appear to contribute significantly to the regional population dynamics of the pest. Substantial parasitism of nymphal stages throughout the study period indicates that native parasitoid species and other natural enemies are important sources of SLW mortality in Australian cotton production systems. Weather conditions and use of broad-spectrum insecticides for pest control are implicated in the initial outbreak and on-going pest status of SLW in the region.