Adsorption isotherm studies of Cd (II), Pb (II) and Zn (II) ions bioremediation from aqueous solution using unmodified and EDTA-modified maize cob

The need to clean-up heavy metal contaminated environment can not be over emphasized. This paper describes the adsorption isotherm studies of Cd (II), Pb (II) and Zn (II) ions from aqueous solution using unmodified and EDTA-modified maize cob. Maize cob was found to be an excellent adsorbent for the removal of these metal ions. The amount of metal ions adsorbed increased as the initial concentration increased. Also, EDTA - modification enhanced the adsorption capacity of maize cob probably due to the chelating ability of EDTA. Among the three adsorption isotherm tested, Dubinin-Radushkevich gave the best fit with R² value ranging from 0.9539 to 0.9973 and an average value of 0.9819. This is followed by Freundlich isotherm (Ave. 0.9783) and then the Langmuir isotherm (Ave. 0.7637). The sorption process was found to be a physiosorption process as seen from the apparent energy of adsorption which ranged from 2.05KJ\mol to 4.56KJ\mol. Therefore, this study demonstrates that maize cob which is an environmental pollutant could be used to adsorb heavy metals and achieve cleanliness thereby abating environmental nuisance caused by the maize cob.

A fluorescence probe study of gemini surfactants in aqueous solution: a comparison between n-2-n and n-6-n series of the alkanediyl-a,w-bis (dimethylalkylammonium bromides)

Two series of alkanediyl-a,w-bis (dimethylalkylammonium bromide (n-2-n and n-6-n; n=8, 10,12, and 16) have been synthesized and their micelles properties studied in aqueous solution using pyrene, pyrenecarboxaldehyde (PCA) and 1,8 anilinonaphtalene sulfonic acid sodium salt (ANS) as fluorescent probes. The micelles from these surfactants have been characterized on the basis of the information provided by micelle-solubilized fluorescent probes. The obtained results indicated that the surfactant concentration at which a marked decrease in l max parameter of pyrenecarboxaldehyde (PCA) occurs corresponds to the CMC determined by conductimetric measurements. Changes in the emission spectra of ANS and PCA observed in the submicellar range for both surfactants series (n-2-n and n-6-n) were interpreted as formation of pre-aggregates. It was found that the dimeric surfactants with long spacer (s= 6) form more hydrated aggregates when compared with those formed by the n-2-n and CnTAB surfactants series. This was attributed to a more difficult packing of n-6-n surfactant molecules to form micelles.

Spectrophotometric flow injection procedure to indirect determination of paracetamol in pharmaceutical formulations using o-tolidine as reagent

A spectrophotometric flow injection method for the determination of paracetamol in pharmaceutical formulations is proposed. The procedure was based on the oxidation of paracetamol by sodium hypochloride and the determination of the excess of this oxidant using o-tolidine dichloride as chromogenic reagent at 430 nm. The analytical curve was linear in the paracetamol concentration range from 8.50 x 10-6 to 2.51 x 10-4 mol L-1 with a detection limit of 5.0 x 10-6 mol L-1. The relative standard deviation was smaller than 1.2% for 1.20 x 10-4 mol L-1 paracetamol solution (n = 10). The results obtained for paracetamol in pharmaceutical formulations using the proposed flow injection method and those obtained using a USP Pharmacopoeia method are in agreement at the 95% confidence level.

Thermal behavior of corn starch granules modified by acid treatment at 30 and 50°C

Unprocessed native starches are structurally too weak and functionally too restricted for application in today's advanced food technologies. Processing is necessary to engender a range of functionality. Naturals or natives starches can be modified by using several methods physical, chemical, enzymatic or combined, according industrial purposes. In this work, native corn starch was hydrolyzed by hydrochloric acid solution and investigated by using thermoanalytical techniques (thermogravimetry - TG, differential thermal analysis - DTA and differential scanning calorimetry - DSC), as well as optical microscopy and X-ray diffractometry. After acid treatment at 30 and 50°C, a decrease of gelatinization enthalpy (ΔHgel) was verified. Optical microscopy and X-ray diffractometry allowed us to verify the granules contorn and rugosity typical of cereal starches.

Thermodynamic quantities of solvation and dilution for some acetanilide derivatives in octanol and water mutually saturateds

Based on published thermodynamic quantities for solution, partitioning and sublimation of acetanilide (ACN), acetaminophen (ACP) and Phenacetin (PNC), the thermodynamic quantities for drugs solvation in octanol-saturated water (W(ROH)) and water-saturated octanol (ROH(W)) as well as the drugs dilution in ROH(W) were calculated. The Gibbs energies of solvation were favourable in all cases. The respective enthalpies and entropies were negative indicating an enthalpy-driving for the solvation process in all cases. On the other hand, the Gibbs energies of dilution were favourable for ACP and PNC but unfavourable for ACN, whereas the respective enthalpies and entropies were negative for ACP and PNC but positive for ACN indicating enthalpy-driving for the dilution process in the case of the former drugs and entropy-driving for the latter. From the obtained values for the transfer processes, an interpretation based on solute-solvent interactions was developed.

Evaluating the Advantages of Implementing a CRM solution

CRM-järjestelmän avulla pyritään yleisesti tehostamaan liiketoimintaprosesseja. Yrityksestä, kuin myös toimialasta riippuen hyödyt sekä tavoitteet vaihtelevat jonkin verran. Usein CRM-järjestelmän avulla saavutettavien hyötyjen mittaaminen ja arviointi organisaatiossa koetaan hankalaksi ja täten todellinen hyötyjen arviointi jää suppeaksi. Tämän tutkimuksen tavoitteena oli kartoittaa etuja, joita CRM-järjestelmän käyttöönotto on todellisuudessa tuonut yrityksille. Tutkimus kulminoituu laskentamalliin, jonka avulla CRM käytön hyödyt konvertoidaan konkreettiseksi rahasummaksi. Tutkimuksessa pyritään vastaamaan seuraaviin tutkimuskysymyksiin: 1. Kun yritys suunnitteli CRM-sovelluksen käyttöönottoa, mitkä olivat järjestelmälle asetetut tavoitteet? 2. Onko yritys saavuttanut CRM-järjestelmälle asetetut tavoitteet? 3. Onko yritys saavuttanut odottamattomia hyötyjä CRM-järjestelmän käytön avulla? 4. Mitkä ovat CRM-järjestelmän tärkeimmät kehityskohteet käyttökokemusten perusteella? Tutkimus perustuu CRM-kirjallisuuden avulla luotuun teoriaviitekehykseen. Teoriaviitekehyksen pohjalta luotiin ideaalimalli ja mallin pohjalta web-survey -kysely. Kyselyn tulosten perusteella toteutettiin haastatteluja, joilla pyrittiin saamaan tutkimustuloksiin syvyyttä.

Potential of utilization of rain water excess for irrigation of green roofs in Mato Grosso, Brasil

The aim of this study was to identify the relation between the evapotranspirometer demand and the supply of water from local rainfall, evaluating the possibility of using water excess for irrigation of Green Roofs in the State of Mato Grosso, in Brazil. The study was done using a series of historical data provided by the National Institute of Meteorology (INMET - Instituto Nacional de Meteorologia) which has official climatological stations in 12 cities and regions of the State. The evapotranspiration values were obtained by the Penman-Monteith method and by the Climatic Water Balance (CWB) by the Thornthwaite and Mather method using Available Water Capacity (AWC) of 12mm. With the CWB the excess and deficit were calculated, which were used for the estimative of the volume and area of a reservoir as a function of a collector area of a roof of 100m² and the volume of supplementary water for irrigation. With the obtained results, it was found that in most investigated regions of the State the use of green roofs is not compromised by the water deficiency. On the other hand, the use of a reservoir to accumulate the rain water excess may be impractical, because it requires a considerable area for installation and also because of the high cost of the land.

Concentration of injetion solution and its effects on soil and on yield of fertirrigated banana cv. Terra Maranhão

The Fertigation is the combined application of water and nutrients to a crop. It can be adapted to all types of agricultural crops. The objective of this study was to evaluate the effect of urea concentration in irrigation water on electrical conductivity of the soil solution and saturation extract along the first cycle of banana cv. Terra Maranhão. The experiment followed a completely randomized design with six treatments and ten replications. Treatments regarded for using three urea concentrations (1.0; 2.5 and 4.0 g L-1) in irrigation water applied by two micro irrigation systems (microsprinkler and drip). Results showed that there was a linear elevation of electrical conductivity of saturation extract and soil solution with the increase on concentration of urea in the injection solution. Urea should be used under concentrations up to 2.5 g L-1 in irrigation water without causing increase on electric conductivity of soil solution and saturation extract, considering 1.1 dS m-1 as the tolerated value for the crop. Nitrate in the soil solution increased significantly with the increase of urea concentration in the injection solution. The maximum concentration of nitrate in the soil occurred for 4,0 g L-1 concentration of the injection solution.

Induction of labor with titrated oral misoprostol solution versus oxytocin in term pregnancy: randomized controlled trial

PURPOSE: To evaluate the effectiveness and the safety of orally administered misoprostol in comparison to intravenously infused oxytocin for labor induction in term pregnant women. METHODS: Between 2008 and 2010, a total of 285 term pregnant women whom were candidate for vaginal delivery were assessed for eligibility to enter the study. Twenty five patients were excluded for different reasons; and 260 included women were randomly assigned to one of the two groups according to the method of treatment, misoprostol or oxytocin. The misoprostol group received 25 µg every 2 hours for up to 24 hours for induction. The oxytocin group received an infusion of 10 IU which was gradually increased. The time from induction to delivery and induction to the beginning of the active phase and successful inductions within 12, 18, and 24 hours were recorded. The trial is registered at irct.ir, number IRCT2012061910068N1. RESULTS: Failure of induction, leading to caesarean section was around 38.3% in the oxytocin group and significantly higher than that of the misoprostol group (20.3%) (p<0.001). Despite the more prevalent failure in the oxytocin group, the mean time intervals from induction to active phase and labor of this group were both significantly less than the misoprostol group (10.1±6.1 and 13.2±7.7 versus 12.9±5.4 and 15.6±5.1 hours respectively, both p-values were <0.05). Maternal and fetal complications were comparable between groups except gastrointestinal symptoms which were encountered more frequently in the misoprostol (10.9 versus 3.9%, p=0.03). CONCLUSIONS: Misoprostol is a safe and effective drug with low complications for the induction of labor. Failure is seen less with misoprostol and caesarean sections are less frequently indicated as compared to oxytocin.

From network pictures to network insight in solution business – the role of internal communication

Operating in business-to-business markets requires an in-depth understanding on business networks. Actions and reactions made to compete in markets are fundamentally based on managers‘ subjective perceptions of the network. However, an amalgamation of these individual perceptions, termed a network picture, to a common company level shared understanding on that network, known as network insight, is found to be a substantial challenge for companies. A company‘s capability to enhance common network insight is even argued to lead competitive advantage. Especially companies with value creating logics that require wide comprehension of and collaborating in networks, such as solution business, are necessitated to develop advanced network insight. According to the extant literature, dispersed pieces of atomized network pictures can be unified to a common network insight through a process of amalgamation that comprises barriers/drivers of multilateral exchange, manifold rationality, and recursive time. However, the extant body of literature appears to lack an understanding on the role of internal communication in the development of network insight. Nonetheless, the extant understanding on the amalgamation process indicates that internal communication plays a substantial role in the development of company level network insight. The purpose of the present thesis is to enhance understanding on internal communication in the amalgamation of network pictures to develop network insight in the solution business setting, which was chosen to represent business-to-business value creating logic that emphasizes the capability to understand and utilize networks. Thus, in solution business the role of succeeding in the amalgamation process is expected to emphasize. The study combines qualitative and quantitative research by means of various analytical methods including multiple case analysis, simulation, and social network analysis. Approaching the nascent research topic with differing perspectives and means provides a broader insight on the phenomenon. The study provides empirical evidence from Finnish business-to-business companies which operate globally. The empirical data comprise interviews (n=28) with managers of three case companies. In addition the data includes a questionnaire (n=23) collected mainly for the purpose of social network analysis. In addition, the thesis includes a simulation study more specifically achieved by means of agent based modeling. The findings of the thesis shed light on the role of internal communication in the amalgamation process, contributing to the emergent discussion of network insights and thus to the industrial marketing research. In addition, the thesis increases understanding on internal communication in the change process to solution business, a supplier‘s internal communication in its matrix organization structure during a project sales process, key barriers and drivers that influence internal communication in project sales networks, perceived power within industrial project sales, and the revisioning of network pictures. According to the findings, internal communication is found to play a substantial role in the amalgamation process. First, it is suggested that internal communication is a base of multilateral exchange. Second, it is suggested that internal communication intensifies and maintains manifold rationality. Third, internal communication is needed to explicate the usually differing time perspectives of others and thus it is suggested that internal communication has role as the explicator of recursive time. Furthermore, the role of an efficient amalgamation process is found to be emphasized in solutions business as it requires a more advanced network insight for cross-functional collaboration. Finally, the thesis offers several managerial implications for industrial suppliers to enhance the amalgamation process when operating in solution business.

Exploring relationship between marketing and sales - a case study of B2B ICT solution sales

Following the current trend of companies in changing and developing their businesses from transactional approach to relationship and solution oriented approach has set new requirements to internal cooperation of companies too. The relationship between marketing and sales has been identified to be critical to company's success here, but surprisingly little is known about it. The purpose of this study was to deepen understanding of the relationship between sales and marketing in business-to-business sales from operative sales employees' perspectives in solution selling context. The aim was to develop an explorative analytical construction and framework of the interface. The study was conducted as a literature review and an empirical qualitative explorative single case study. The data was collected by conducting six thematic interviews with sales employees of the case company. Observing sales and marketing, written documents and other materials used in sales were used as secondary source of information. The data was analyzed using qualitative case study analysis methods. The findings of the study support previous research findings of the interface between marketing and sales but also bring new propositions as analytical framework to construct the interface. As such, the interface was found to be a multi-dimensional and complex dynamic construction. As results of this study, there was an exploratory framework constructed. The construction consists of three explorative contexts of the interface: internal context, relationship emphasizing context and solution selling context. These contexts are further divided into lower levels as an outcome of the analysis. In addition the identified contexts, there are also conceptual domains identified, which are common to all the contexts. The role of mutual, cross-functional knowledge creation was found to be central in the interface.

Algorithm to determine the intersection curves between bezier surfaces by the solution of multivariable polynomial system and the differential marching method

The determination of the intersection curve between Bézier Surfaces may be seen as the composition of two separated problems: determining initial points and tracing the intersection curve from these points. The Bézier Surface is represented by a parametric function (polynomial with two variables) that maps a point in the tridimensional space from the bidimensional parametric space. In this article, it is proposed an algorithm to determine the initial points of the intersection curve of Bézier Surfaces, based on the solution of polynomial systems with the Projected Polyhedral Method, followed by a method for tracing the intersection curves (Marching Method with differential equations). In order to allow the use of the Projected Polyhedral Method, the equations of the system must be represented in terms of the Bernstein basis, and towards this goal it is proposed a robust and reliable algorithm to exactly transform a multivariable polynomial in terms of power basis to a polynomial written in terms of Bernstein basis .

Solution of aerospace problems using structured and unstructured strategies

Products developed at industries, institutes and research centers are expected to have high level of quality and performance, having a minimum waste, which require efficient and robust tools to numerically simulate stringent project conditions with great reliability. In this context, Computational Fluid Dynamics (CFD) plays an important role and the present work shows two numerical algorithms that are used in the CFD community to solve the Euler and Navier-Stokes equations applied to typical aerospace and aeronautical problems. Particularly, unstructured discretization of the spatial domain has gained special attention by the international community due to its ease in discretizing complex spatial domains. This work has the main objective of illustrating some advantages and disadvantages of numerical algorithms using structured and unstructured spatial discretization of the flow governing equations. Numerical methods include a finite volume formulation and the Euler and Navier-Stokes equations are applied to solve a transonic nozzle problem, a low supersonic airfoil problem and a hypersonic inlet problem. In a structured context, these problems are solved using MacCormack’s implicit algorithm with Steger and Warming’s flux vector splitting technique, while, in an unstructured context, Jameson and Mavriplis’ explicit algorithm is used. Convergence acceleration is obtained using a spatially variable time stepping procedure.