Características geológicas y geotécnicas de los lodos de flotación de la Sierra Minera de Cartagena-La Unión (SE España)

We present the results of a geological and geotechnical characterization of the metallurgic waste from the Sierra Minera de Cartagena-La Union. We have studied eight tailings dams from which we collected and analysed 42 samples of metallurgic waste. We measured grainsize distribution, the specific gravity of solid particles, plasticity index, permeability, both in situ and in the laboratory, direct shear characteristicsand moisture content. According to size distribution the tailings can be classified as sandy silt. Their plasticity index ranges from medium to nil. The internal friction angle varies between 28 and 42 degrees. Cohesion is between 0 and 2.2 t/m2. The specific gravity of the solid particles ranges widely from 1.8 to 4 g/cm3. The saturated hydraulic conductivity values vary between 1.3x 10-5 and 3.2x 10-9 m/s.The water content measured in situ shows that the degree of saturation remains relatively high despite low rainfall and high evaporation rates. Several tailings dams have failed. The leading causes of tailings-dam failure are: 1) slope instability; 2) overflow; 3) erosion; and 4) subsidence or collapse. The main factor leading to dam failure is that the tailings stored in the ponds are highly saturated

Reflexiones sobre el diseño por competencias en el trabajo de campo en Geología

Learning activities outside the classroom in Earth Sciences are considered fundamental to achieve an adequate level of knowledge. New pedagogical perspectives, structured in competency-based activities, provide a useful tool to improve the effectiveness of field geology classes. In this paper, we point out some general educational aspects, and we propose a curriculum design focused on accomplishing the competencies that go with fieldtrips in Geology courses

Quantitative analysis of crystal/grain sizes and their distributions in 2D and 3D

We review methods to estimate the average crystal (grain) size and the crystal (grain) size distribution in solid rocks. Average grain sizes often provide the base for stress estimates or rheological calculations requiring the quantification of grain sizes in a rock's microstructure. The primary data for grain size data are either 1D (i.e. line intercept methods), 2D (area analysis) or 3D (e.g., computed tomography, serial sectioning). These data have been used for different data treatments over the years, whereas several studies assume a certain probability function (e.g., logarithm, square root) to calculate statistical parameters as the mean, median, mode or the skewness of a crystal size distribution. The finally calculated average grain sizes have to be compatible between the different grain size estimation approaches in order to be properly applied, for example, in paleo-piezometers or grain size sensitive flow laws. Such compatibility is tested for different data treatments using one- and two-dimensional measurements. We propose an empirical conversion matrix for different datasets. These conversion factors provide the option to make different datasets compatible with each other, although the primary calculations were obtained in different ways. In order to present an average grain size, we propose to use the area-weighted and volume-weighted mean in the case of unimodal grain size distributions, respectively, for 2D and 3D measurements. The shape of the crystal size distribution is important for studies of nucleation and growth of minerals. The shape of the crystal size distribution of garnet populations is compared between different 2D and 3D measurements, which are serial sectioning and computed tomography. The comparison of different direct measured 3D data; stereological data and direct presented 20 data show the problems of the quality of the smallest grain sizes and the overestimation of small grain sizes in stereological tools, depending on the type of CSD. (C) 2011 Published by Elsevier Ltd.

Globally aligned photomosaic of the Lucky Strike hydrothermal vent field (Mid-Atlantic Ridge, 37°18.5’N): Release of georeferenced data, mosaic construction, and viewing software

We present a georeferenced photomosaic of the Lucky Strike hydrothermal vent field (Mid-Atlantic Ridge, 37°18’N). The photomosaic was generated from digital photographs acquired using the ARGO II seafloor imaging system during the 1996 LUSTRE cruise, which surveyed a ~1 km2 zone and provided a coverage of ~20% of the seafloor. The photomosaic has a pixel resolution of 15 mm and encloses the areas with known active hydrothermal venting. The final mosaic is generated after an optimization that includes the automatic detection of the same benthic features across different images (feature-matching), followed by a global alignment of images based on the vehicle navigation. We also provide software to construct mosaics from large sets of images for which georeferencing information exists (location, attitude, and altitude per image), to visualize them, and to extract data. Georeferencing information can be provided by the raw navigation data (collected during the survey) or result from the optimization obtained from imatge matching. Mosaics based solely on navigation can be readily generated by any user but the optimization and global alignment of the mosaic requires a case-by-case approach for which no universally software is available. The Lucky Strike photomosaics (optimized and navigated-only) are publicly available through the Marine Geoscience Data System (MGDS, http://www.marine-geo.org). The mosaic-generating and viewing software is available through the Computer Vision and Robotics Group Web page at the University of Girona (http://eia.udg.es/_rafa/mosaicviewer.html)

Monitoring natural hazards

Few subjects have caught the attention of the entire world as much as those dealing with natural hazards. The first decade of this new millennium provides a litany of tragic examples of various hazards that turned into disasters affecting millions of individuals around the globe. The human losses (some 225,000 people) associated with the 2004 Indian Ocean earthquake and tsunami, the economic costs (approximately 200 billion USD) of the 2011 Tohoku Japan earthquake, tsunami and reactor event, and the collective social impacts of human tragedies experienced during Hurricane Katrina in 2005 all provide repetitive reminders that we humans are temporary guests occupying a very active and angry planet. Any examples may have been cited here to stress the point that natural events on Earth may, and often do, lead to disasters and catastrophes when humans place themselves into situations of high risk. Few subjects share the true interdisciplinary dependency that characterizes the field of natural hazards. From geology and geophysics to engineering and emergency response to social psychology and economics, the study of natural hazards draws input from an impressive suite of unique and previously independent specializations. Natural hazards provide a common platform to reduce disciplinary boundaries and facilitate a beneficial synergy in the provision of timely and useful information and action on this critical subject matter. As social norms change regarding the concept of acceptable risk and human migration leads to an explosion in the number of megacities, coastal over-crowding and unmanaged habitation in precarious environments such as mountainous slopes, the vulnerability of people and their susceptibility to natural hazards increases dramatically. Coupled with the concerns of changing climates, escalating recovery costs, a growing divergence between more developed and less developed countries, the subject of natural hazards remains on the forefront of issues that affect all people, nations, and environments all the time.This treatise provides a compendium of critical, timely and very detailed information and essential facts regarding the basic attributes of natural hazards and concomitant disasters. The Encyclopedia of Natural Hazards effectively captures and integrates contributions from an international portfolio of almost 300 specialists whose range of expertise addresses over 330 topics pertinent to the field of natural hazards. Disciplinary barriers are overcome in this comprehensive treatment of the subject matter. Clear illustrations and numerous color images enhance the primary aim to communicate and educate. The inclusion of a series of unique ?classic case study? events interspersed throughout the volume provides tangible examples linking concepts, issues, outcomes and solutions. These case studies illustrate different but notable recent, historic and prehistoric events that have shaped the world as we now know it. They provide excellent focal points linking the remaining terms in the volume to the primary field of study. This Encyclopedia of Natural Hazards will remain a standard reference of choice for many years.

Application of K-feldspar-jadeite-quartz barometry to eclogite facies metagranites and metapelites in the Sesia Lanzo Zone (Western Alps, Italy)

The eclogite facies assemblage K-feldspar-jadeite-quartz in metagranites and metapelites from the Sesia-Lanzo Zone (Western Alps, Italy) records the equilibration pressure by dilution of the reaction jadeite + quartz = albite. The metapelites show partial transformation from a pre-Alpine assemblage of garnet (Alm(63)Prp(26)Grs(10))-K-feldspar-plagioclase-biotite +/- sillimanite to the Eo-Alpine high-pressure assemblage garnet (Alm(50)Prp(14)Grs(35))-jadeite (Jd(80-97)Di(0-4)Hd(0-8)Acm(0-7))=zoisite-phengite. Plagioclase is replaced by jadeite-zoisite-kyanite-K-feldspar-quartz and biotite is replaced by garnet-phengite or omphacite-kyanite-phengite. Equilibrium was attained only in local domains in the metapelites and therefore the K-feldspar-jadeite-quartz (KJQ) barometer was applied only to the plagioclase pseudomorphs and K-feldspar domains. The albite content of K-feldspar ranges from 4 to 11 mol% in less equilibrated assemblages from Val Savenca and from 4 to 7 mol% in the partially equilibrated samples from Monte Mucrone and the equilibrated samples from Montestrutto and Tavagnasco. Thermodynamic calculations on the stability of the assemblage K-feldspar-jadeite-quartz using available mixing data for K-feldspar and pyroxene indicate pressures of 15-21 kbar (+/- 1.6-1.9 kbar) at 550 +/- 50 degrees C. This barometer yields direct pressure estimates in high-pressure rocks where pressures are seldom otherwise fixed, although it is sensitive to analytical precision and the choice of thermodynamic mixing model for K-feldspar. Moreover, the KJQ barometer is independent of the ratio P-H2O/P-T. The inferred limiting a(H2O) for the assemblage jadeite-kyanite in the metapelites from Val Savenca is low and varies from 0.2 to 0.6.

Determinación de la longitud de la falla y velocidad de ruptura para terremotos de magnitud media

En el proceso de inversión de la función de directividad para la obtención de la longitud de falla y velocidad de mptura, en el caso de terremotos de magnitud media, es muy dificil obtener ambos parámetros independientemente y deben hacerse hipótesis sobre uno de los dos parámetros. Proponemos una solución a este problema mediante un proceso iterativo, que iniciamos con un valor hipotético de la velocidad de ruptura. El resultado final resulta ser independiente del valor de partida. Mediante este proceso hemos obtenido la longitud de falla y velocidad de ruptura de dos terremotos, el del 18-nov-1970, ocurrido en la Dorsal Oriental del Pacifico, y el del 4-jul-1966, ocurrido en la Dorsal Centro-Atlántica. Para el sismo del 18-nov-1970 los valores obtenidos en la b = (18 4- 1) km v = (2.3 f 0.1) kmls y para el sismo del 4-jul-1966 b = (19 f 2) km, v = (2.1 i 0.1) kmls. Las desviaciones tipicas de estos parámetros, del orden del 5-10 %, son inferiores a las obtenidas en trabajos previos.

Archaeology on the Road, July 2010

Not only are we excited that Team Archaeology is back for our third ride, we are energized to be part of a “Human and Natural History” partnership that allows us expanded opportunities to share the story of Iowa’s amazing past. Once again there will be archaeologists along for the ride, as well as at Expo and this year at roadside locations Day One, Five and Six. Don’t hesitate to ask about the history of the first people to travel this landscape as well as the stories of each generation that has contributed to what we know of ourselves today. We will also feature information about the landscape and natural resources of Iowa you will encounter along the route through our partnering colleagues specializing in geology, hydrology, and other earth sciences. Enjoy using this booklet as your guide to the week’s activities and please help yourself to free materials from our outreach booth about our shared past and the natural world we depend on. Ride smart, be safe, and when you get home, be sure to tell your friends and neighbors about Iowa archaeology!

Metallogenic model of the Trepca Pb-Zn-Ag skarn deposit, Kosovo: Evidence from fluid inclusions, Rare Earth Elements, and stable isotope data

The Trepca Pb-Zn-Ag skarn deposit (29 Mt of ore at 3.45% Pb, 2.30% Zn, and 80 g/t Ag) is located in the Kopaonik block of the western Vardar zone, Kosovo. The mineralization, hosted by recrystallized limestone of Upper Triassic age, was structurally and lithologically controlled. Ore deposition is spatially and temporally related with the postcollisional magmatism of Oligocene age (23-26 Ma). The deposit was formed during two distinct mineralization stages: an early prograde closed-system and a later retrograde open-system stage. The prograde mineralization consisting mainly of pyroxenes (Hd(54-100)Jo(0-45)Di(0-45)) resulted from the interaction of magmatic fluids associated with Oligocene (23-26 Ma) postcollisional magmatism. Whereas there is no direct contact between magmatic rocks and the mineralization, the deposit is classified as a distal Pb-Zn-Ag skarn. Abundant pyroxene reflects low oxygen fugacity (<10(-31) bar) and anhydrous environment. Fluid inclusion data and mineral assemblage limit the prograde stage within a temperature range between 390 degrees and 475 degrees C. Formation pressure is estimated below 900 bars. Isotopic composition of aqueous fluid, inclusions hosted by hedenbergite (delta D = -108 to -130 parts per thousand; delta O-18 = 7.5-8.0 parts per thousand), Mn-enriched mineralogy and high REE content of the host carbonates at the contact with the skarn mineralization suggest that a magmatic fluid was modified during its infiltration through the country rocks. The retrograde mineral assemblage comprises ilvaite, magnetite, arsenopyrite, pyrrhotite, marcasite, pyrite, quartz, and various carbonates. Increases in oxygen and sulfur fugacities, as well as a hydrous character of mineralization, require an open-system model. The opening of the system is related to phreatomagmatic explosion and formation of the breccia. Arsenopyrite geothermometer limits the retrograde stage within the temperature range between 350 degrees and 380 degrees C and sulfur fugacity between 10(-8.8) and 10(-7.2) bars. The principal ore minerals, galena, sphalerite, pyrite, and minor chalcopyrite, were deposited from a moderately saline Ca-Na chloride fluid at around 350 degrees C. According to the isotopic composition of fluid inclusions hosted by sphalerite (delta D = -55 to -74 parts per thousand; delta O-18 = -9.6 to -13.6 parts per thousand), the fluid responsible for ore deposition was dominantly meteoric in origin. The delta S-31 values of the sulfides spanning between -5.5 and +10 parts per thousand point to a magmatic origin of sulfur. Ore deposition appears to have been largely contemporaneous with the retrograde stage of the skarn development. Postore stage accompanied the precipitation of significant amount of carbonates including the travertine deposits at the deposit surface. Mineralogical composition of travertine varies from calcite to siderite and all carbonates contain significant amounts of Mn. Decreased formation temperature and depletion in the REE content point to an influence of pH-neutralized cold ground water and dying magmatic system.

Mineralogical, K-Ar, stable and Sr isotope systematics of K-white micas during very low-grade metamorphism of limestones (Helvetic nappes, Western Switzerland)

Mineralogical, K-Ar, Rb-Sr and stable isotope analyses have been carried out on K-white micas from Helvetic Malm limestones in order to examine their evolution during very low- to low-grade Alpine metamorphism, associated with intense ductile deformation. Metamorphic temperatures were estimated al approximately 300-degrees-C from stable isotopes (quartz-calcite thermometry), occurrence of chloritoid, and `'epizonal'' illite crystallinity index. K-white micas consist of variable mixtures of 2M, phengite and muscovite, as revealed by detailed X-ray diffraction analyses using peak decomposition of the (060, 331) spectra. K-Ar apparent ages display a strong grain-size dependence in which mainly fine-grained size fractions (< 2 mum) record Alpine ages (37-15 Ma). However, these ages provide a relative rather than an absolute chronology of the diachronous Alpine metamorphic evolution of the Helvetic nappes. The resetting of the K-Ar isotopic system of K-white micas to Alpine metamorphic conditions reflects an apparent combination of crystallization/recrystallization and radiogenic Ar-40 diffusion loss. The oxygen isotope compositions of micas (+ 15 to + 22 parts per thousand) are intermediate between detrital and O-18-enriched values expected for micas neoformed within an abundant marine carbonate matrix. No isotopic equilibrium has been reached between calcite and micas. The variable depletion of hydrogen isotope compositions (- 126 to - 82 parts per thousand) is influenced by the interaction with organic matter under closed-system conditions. Organic matter, if not removed, may also represent a serious source of error in K-Ar age determination, by introducing radiogenic Ar-40 contamination. Sr-87/Sr-86 isotope ratios of micas range from 0.70879 to 0.70902 with one outlier at 0.71794. The low values reflect Sr exchange with calcite occurring during crystallization/recrystallization of micas under closed-system conditions.

Late Jurassic continental flood basalt doleritic dykes in northwestern Cuba: remnants of the Gulf of Mexico opening

Accreted terranes, comprising a wide variety of Late Jurassic and Early Cretaceous igneous and sedimentary rocks are an important feature of Cuban geology. Their characterization is helpful for understanding Caribbean paleogeography. The Guaniguanico terrane (western Cuba) is formed by upper Jurassic platform sediments intruded by microgranular dolerite dykes. The geochemical characteristics of the dolerite whole rock samples and their minerals (augitic clinopyroxene, labradorite and andesine) are consistent with a tholeiitic affinity. Major and trace element concentrations as well as Nd, Sr and Pb isotopes show that these rocks also have a continental affinity. Sample chemistry indicates that these lavas are similar to a low Ti-P2O5 (LTi) variety of continental flood basalts (CFB) similar to the dolerites of Ferrar (Tasmania). They derived from mixing of a lithospheric mantle Source and an asthenopheric component similar to E-MORB with minor markers of crustal contamination and sediment assimilation. However, the small quantity of Cuban magmatic rocks, similarly to Tasmania, Antarctica and Siberia differs from other volumetrically important CFB occurrences Such as Parana and Deccan. These dolerites are dated as 165-150 Ma and were emplaced during the separation of the Yucatan block from South America. They could in fact be part of the Yucatan-South America margin through which the intrusive system was emplaced and which was later accreted to the Cretaceous arc of central Cuba and to the Palaeogene arc of eastern Cuba. These samples could therefore reflect the pre-rift stage between North and South America and the opening of the gulf of Mexico.