Estudo numérico do comportamento de muros de arrimo em alvenaria estrutural de blocos vazados

Usually masonry structures has low tension strength, hence the design to flexural efforts can results in high reinforcement ratio, specification of high unit and prism strength, structural members with larger section dimensions and modification in structural arrangement to be possible to use masonry members. The main objective of this study is to evaluate the stiffness, the efforts distribution and the effect of horizontal elements (girders) and vertical elements (counterforts) distribution on the behavior of masonry blocks retaining walls. For this purpose, numerical modeling was performed on typical retaining wall arrangements by varying the amount and placement of horizontal and vertical elements, beyond includes elements simulating the reactions of the soil supporting the foundation of the wall. The numerical modeling also include the macro modeling strategy in which the units, mortar and grout are discretized by a standard volume that represents the masonry elastic behavior. Also, numerical model results were compared with those ones of simplified models usually adopted in bending design of masonry elements. The results show horizontal displacements, principal and shear stresses distribution, and bending moments diagrams. From the analysis it was concluded that quantity and manner of distribution of the girders are both important factors to the panel flexural behavior, the inclusion of the foundation changed significantly the behavior of the wall, especially the horizontal displacements, and has been proposed a new way of considering the flanges section of the counterforts

Desempenho de argamassas produzidas com agregados reciclados oriundos do resíduo de construção e demolição da Grande Natal-RN

The construction industry is responsible for generating a lot of waste because of their activities. Consequently, it is noticeable the occurrence of environmental problems in terms of its disposal in inappropriate places. Faced with this problem, some studies have been conducted with the aim of developing technologies and alternatives for recycling construction and demolition waste (CDW), motivated by the scarcity of natural resources and reduction of environmental problems generated. The research aims to characterize the recycled aggregates derived from construction and demolition waste (CDW) produced in the Greater Natal-RN and analyze the performance of mortar coating produced with recycled aggregates. The study includes the chemical , physical and microstructural characterization of recycled aggregates , as well as conducting microscopic analysis and laboratory tests in the fresh state (consistency index , water retention , bulk density and content of entrained air ) and in the hardened state ( compressive strength , tensile strength in bending , water absorption by immersion and capillary , mass density and void ratio ) for mortars produced from different levels of substitution of aggregates ( 0, 20 %, 40 %, 60 %, 80 % and 100 %). The results were satisfactory, providing mortars produced with recycled aggregates, smaller mass density and dynamic modulus values as well as an increase in the rates of absorption and porosity. The tensile strength in bending and compression for TP1 (1:2:8) trait were lower for mortars produced with recycled aggregates and the best result was 20% for replacement. For the TP2 (1:8) mapping, there was an increase in resistance to traction and compression and the best result was for 100% replacement of natural aggregates by recycled. The experiments led to the conclusion that the technical and economic point of view that the mortars produced with recycled aggregates can be used in construction, only if there is an effective control in production processes of recycled aggregate and at the dosage of mortars

Agentes Inteligentes com Foco de Atenção Afetivo em Simulações Baseadas em Agentes

Simulations based on cognitively rich agents can become a very intensive computing task, especially when the simulated environment represents a complex system. This situation becomes worse when time constraints are present. This kind of simulations would benefit from a mechanism that improves the way agents perceive and react to changes in these types of environments. In other worlds, an approach to improve the efficiency (performance and accuracy) in the decision process of autonomous agents in a simulation would be useful. In complex environments, and full of variables, it is possible that not every information available to the agent is necessary for its decision-making process, depending indeed, on the task being performed. Then, the agent would need to filter the coming perceptions in the same as we do with our attentions focus. By using a focus of attention, only the information that really matters to the agent running context are perceived (cognitively processed), which can improve the decision making process. The architecture proposed herein presents a structure for cognitive agents divided into two parts: 1) the main part contains the reasoning / planning process, knowledge and affective state of the agent, and 2) a set of behaviors that are triggered by planning in order to achieve the agent s goals. Each of these behaviors has a runtime dynamically adjustable focus of attention, adjusted according to the variation of the agent s affective state. The focus of each behavior is divided into a qualitative focus, which is responsible for the quality of the perceived data, and a quantitative focus, which is responsible for the quantity of the perceived data. Thus, the behavior will be able to filter the information sent by the agent sensors, and build a list of perceived elements containing only the information necessary to the agent, according to the context of the behavior that is currently running. Based on the human attention focus, the agent is also dotted of a affective state. The agent s affective state is based on theories of human emotion, mood and personality. This model serves as a basis for the mechanism of continuous adjustment of the agent s attention focus, both the qualitative and the quantative focus. With this mechanism, the agent can adjust its focus of attention during the execution of the behavior, in order to become more efficient in the face of environmental changes. The proposed architecture can be used in a very flexibly way. The focus of attention can work in a fixed way (neither the qualitative focus nor the quantitaive focus one changes), as well as using different combinations for the qualitative and quantitative foci variation. The architecture was built on a platform for BDI agents, but its design allows it to be used in any other type of agents, since the implementation is made only in the perception level layer of the agent. In order to evaluate the contribution proposed in this work, an extensive series of experiments were conducted on an agent-based simulation over a fire-growing scenario. In the simulations, the agents using the architecture proposed in this work are compared with similar agents (with the same reasoning model), but able to process all the information sent by the environment. Intuitively, it is expected that the omniscient agent would be more efficient, since they can handle all the possible option before taking a decision. However, the experiments showed that attention-focus based agents can be as efficient as the omniscient ones, with the advantage of being able to solve the same problems in a significantly reduced time. Thus, the experiments indicate the efficiency of the proposed architecture

Demanda energética na subsolagem realizada antes e depois de diferentes sistemas de preparo periódico do solo

A subsolagem é uma das operações mecanizadas de elevado custo e demanda energética por área, tradicionalmente utilizada pelos agricultores antes do preparo do solo na descompactação de camadas adensadas. Este trabalho teve como objetivo avaliar a demanda energética na operação de subsolagem realizada antes e depois de diferentes sistemas de preparo periódico num solo classificado como Nitossolo Vermelho Distroférrico. Os sistemas de preparo periódico foram: aração com discos; aração com discos mais uma gradagem de nivelamento; grade aradora; grade aradora mais gradagem de nivelamento e escarificação. O trator utilizado como fonte de potência no experimento foi um Valmet 128 (4x2tda). A demanda energética por área foi menor na subsolagem realizada depois do preparo periódico do solo, proporcionando uma economia de 21,9%. A realização da subsolagem depois do preparo periódico do solo resultou numa diminuição da exigência de força de tração em 21,1% e da potência disponível na barra de tração em 15%.

Consumo de combustível na operação de subsolagem realizada antes e depois de diferentes sistemas de preparo periódico do solo

A subsolagem tem aumentado nos últimos anos de forma indiscriminada, faltando estudos que norteiem os melhores procedimentos para que novos problemas não sejam acrescentados devido a subsolagens inadequadas ou mesmo em solos onde a operação é desnecessária, e principalmente buscar redução no consumo de combustível. Dessa forma, este trabalho teve o objetivo de avaliar o consumo de combustível na operação de subsolagem efetuada antes e depois de diferentes sistemas de preparo periódico do solo, classificado como Nitossolo Vermelho distroférrico. Os preparos foram realizados com arado de discos, arado de discos mais uma gradagem de nivelamento, grade pesada, grade pesada mais gradagem de nivelamento e escarificador. A realização da subsolagem depois dos sistemas de preparo periódico requereu 15% menos de potência na barra de tração. A subsolagem depois dos diferentes sistemas de preparo economizou 16,5% de combustível por área. O deslizamento das rodas motrizes e a velocidade média operacional obtiveram melhor desempenho quando se realizou a subsolagem depois do preparo do solo.

Semeadura direta de milho com dois tipos de sulcadores de adubo, em nível e no sentido do declive do terreno

O presente estudo teve como objetivo avaliar parâmetros operacionais de um conjunto mecanizado envolvendo trator e semeadora, assim como o rendimento da cultura do milho semeada nas diferentes configurações das máquinas e combinações com o ambiente de produção. Os tratamentos consistiram de tipos de sulcadores (discos duplos e hastes), os quais foram avaliados em experimentos em que a operação de semeadura direta do milho foi efetuada transversalmente ao declive (em nível) e em aclive e declive. A semeadura contra o declive e o uso de haste sulcadora implicaram maior demanda de esforço de tração, patinagem do trator e consumo de combustível por área trabalhada e não influenciaram o volume de solo mobilizado, a população de plantas e a produtividade de grãos do milho, em relação à operação realizada em declive e uso de sulcador de discos duplos, respectivamente. A utilização de sulcador do tipo haste resultou em menor número de plantas acamadas e quebradas, em relação ao uso de discos duplos, independentemente do sentido da operação. A principal diferença entre semear em nível ou em declive é a formação de sulcos orientados no sentido do terreno, pela ação de sulcadores do tipo haste e elevada patinagem dos rodados do trator, já que o consumo de combustível por área trabalhada e capacidade operacional não foram afetados por aquelas variáveis.

Desempenho operacional de uma semeadora-adubadora de precisão, em função do preparo do solo e do manejo da cobertura de inverno

Avaliou-se o desempenho operacional de campo de uma semeadora-adubadora de precisão, equipada com seis linhas espaçadas de 550 mm, em um solo muito argiloso, classificado como Nitossolo Vermelho Distrófico Latossólico, na semeadura do feijoeiro (Phaseolus vulgaris L.). Os tratamentos consistiram de três métodos de preparo do solo: a) convencional (uma aração com arado de discos e duas gradagens niveladoras); b) escarificação (uma passagem de escarificador conjugado com rolo destorroador), e c) semeadura direta. Esses procedimentos foram combinados com quatro condições de cobertura do solo no inverno (consórcio aveia-preta + nabo forrageiro manejados com rolo-faca, triturador de palhas, herbicida e solo em pousio). Os métodos de preparo do solo e os manejos da cobertura foram repetidos por três anos consecutivos. Os valores de força e pico de força de tração na barra, patinagem dos rodados motrizes e consumo de combustível foram maiores no preparo com escarificador em relação aos obtidos no preparo convencional e na semeadura direta. A capacidade de campo efetiva foi maior na semeadura direta em relação aos outros tratamentos. Os manejos efetuados nas coberturas vegetais e o solo mantido em pousio não influenciaram em nenhuma das variáveis.

Evaluation of tractive performance of four agricultural tractors in laterally inclined terrain

O presente trabalho teve como objetivo avaliar o desempenho operacional de quatro tratores agrícolas com tração dianteira auxiliar, em função de seis inclinações laterais, em uma pista lateral de ensaios, pertencente à Faculdade de Ciências Agronômicas da Universidade Estadual Paulista, Câmpus de Botucatu. As inclinações laterais foram 0; 5; 10; 15; 20 e 25 graus. em todas estas situações, os tratores operaram com carga predeterminada de tração imposta ao trator tracionado de 40 kN na inclinação de 0 grau. Portanto, foi utilizado um delineamento em blocos casualizados (DBC), sendo seis inclinações e quatro tratores, e com três repetições para cada tratamento. As variáveis analisadas foram patinhagem, força de tração, consumo horário de combustível e velocidade de deslocamento. Concluiu-se que a configuração dos rodados pneumáticos influenciaram no desempenho operacional dos tratores, conforme aumentaram as inclinações laterais do terreno.

Adição de geomanta e tecido não tecido de polipropileno em cimentos geopoliméricos de pega rápida

Geopolymers are cementing materials that depict a number of advantages compared to Portland cement. Contrary to the latter, geopolymers are synthesized at room temperature, thus significantly reducing the emission of CO2 to the atmosphere. Moreover, the composition and synthesis reactions can be tailored to adjust the setting time of the material as well as its compressive mechanical strength. It is then possible to produce geopolymeric cements with short setting times and high compressive strength, although relatively brittle. The objective of the present study was to produce and characterize composite materials by reinforcing fastsetting geopolymeric matrixes with polypropylene geosynthetics (geomats and geotextiles) in an attempt to improve the toughness and tensile strength of the cementing material. Geosynthetics have been increasingly used to reinforce engineering structures, providing higher strength and better toughness. In particular, polypropylene nonwoven and geomats depict other attractive properties such as low density, durability, impact absorption and resistance to abrasion. Fast-setting geopolymers were then synthesized and reinforced with polypropylene nonwoven and geomats. The mechanical strength of the materials, reinforced or not, was characterized. The results showed that relatively short setting times and adequate flowing behavior were achieved by adjusting the composition of the geopolymer. In addition, it is possible to improve the fracture resistance of geopolymeric cements by adding polypropylene geosynthetics. The best results were achieved by reinforcing geopolymer with polypropylene TNT

Compósitos híbridos: desenvolvimento de configuração e efeitos de umidificação

The advantage in using vegetable fibres in place of synthetic fibres such as glass fibre, for reinforcements in composites are: biodegradability, low cost, low density, good tenacity, good thermal properties, low energy content and reduced use of instruments for its treatment or processing. Even though, problems related to low mechanical performance of some of the natural fibres, has caused difficulty in their direct application in structural elements. The use of alternative materials like hybrid composites has been encouraged, thus trying to better the structural performance of the composites with natural fibres. This work presents a comparative study of the strength and stiffness of hybrid composites with orthopthalic polyester matrix reinforced with E-fibre glass, jute and curauá. The experimental part includes uniaxial tension and three point bending tests to determine the mechanical properties of the final product. The hybrid composite was manufactured in a local industry and was in the form of laminates. All the samples were projected to withstand the possible structural applications as reservoirs and pipes. CH (laminated hybrid composite with glass and curauá fibres). The results obtained show clearly the influence of the hybridization in all the types tested and indicate a good mechanical performance of the composite with glass/curauá fibres in relation to the composite with glass fibres. Aspects in relation to the interfaces glass/curauá composites besides the fracture characteristics for all loading types were also analysed

Efeitos do envelhecimento ambiental acelerado em compósitos poliméricos

The advantages of the use of vegetable fibers on the synthetic fibers, such as glass fibers, in the reinforcements in composites are: low cost, low density, good tenacity, good thermal properties and reduced use of instruments for their treatment or processing. However, problems related to poor performance of some mechanical natural fibers, have hindered its direct use in structural elements. In this sense, the emergence of alternative materials such as hybrids composites, involving natural and synthetic fibers, has been encouraged by seeking to improve the performance of structural composites based only on natural fibers. The differences between the physical, chemical and mechanical properties of these fibers, especially facing the adverse environmental conditions such as the presence of moisture and ultraviolet radiation, is also becoming a concern in the final response of these composites. This piece of research presents a comparative study of the strength and stiffness between two composite, both of ortoftalic polyester matrix, one reinforced with fibers of glass-E (CV) and other hybrid reinforced with natural fibers of curauá and fiberglass-E (CH). All the comparative study is based on the influence of exposure to UV rays and steam heated water in composites, simulating the aging environment. The conditions for the tests are accelerated through the use of the aging chamber. The composites will be evaluated through tests of uniaxial static mechanical traction and bending on three points. The composite of glass fiber and hybrid manufacturing industry are using the rolling manual (hand lay-up) and have been developed in the form of composites. All were designed to meet possible structural applications such as tanks and pipes. The reinforcements used in composites were in the forms of short fiber glass-E quilts (450g/m2 - 5cm) of continuous wires and fuses (whose title was of 0.9 dtex) for the curauá fibers. The results clearly show the influence of aging on the environmental mechanical performance of the composite CV and CH. The issues concerning the final characteristics of the fracture for all types of cargoes studied were also analyzed

Fibras de licuri: um reforço vegetal alternativo de compósitos poliméricos

This research is based, at first, on the seeking of alternatives naturals reinforced in place of polymeric composites, also named reinforced plastics. Therein, this work starts with a whole licuri fiber micro structural characterization, as alternative proposal to polymeric composites. Licuri fiber is abundant on the Bahia state flora, native from a palm tree called Syagrus Coronata (Martius) Beccari. After, it was done only licuri fiber laminar composite developing studies, in order to know its behavior when impregnated with thermofix resin. The composite was developed in laminar structure shape (plate with a single layer of reinforcement) and produced industrially. The layer of reinforcement is a fabric-fiber unidirectional of licuri up in a manual loom. Their structure was made of polyester resin ortofitálica (unsaturated) only reinforced with licuri fibers. Fiber characterization studies were based on physical chemistry properties and their constitution. It was made by tension, scanning electron microscopy (SEM), x-ray diffraction (RDX) and thermal analyses (TG and DTA) tests, besides fiber chemistry analyses. Relating their mechanical properties of strength and hardness testing, they were determined through unit axial tension test and flexion in three points. A study in order to know fiber/matrix interface effects, in the final composites results, was required. To better understand the mechanical behavior of the composite, macroscopic and microscopic optical analysis of the fracture was performed

Níveis de adubação para a cultura do milho Safrinha

The objective of this research was to evaluate the effect two hybrids of maize, cultivated on "safrinha" conditions, in different rates of 08-28-16 formula. The treatments consisted of two hybrids of maize (DKB747 e CO32) cultivated in no-tillage system (SPD) and five rates of fertilizer 08-28-16 (100, 200, 300, 400 e 500 kg ha(-1)). The randomized block design was used, with subdivided splots and four replications. The maize was sowed on 02/03/2006 using seeder pneumatic of mechanics traction, with four individual lines, spaced of 0.45 m During maize flowering period, morphologic components were evaluated; the harvest occurred on 150 days after the sowing, when the production components were evaluated. The hybrid of maize DKB747 showed greater efficiency, while the hybrid of maize CO32 was more responsive to rates used. NPK rates on 08-28-16 fomula above 300 kg ha(-1) are not necessary to the hybrid CO32 cultivated on "safrinha" conditions, in Botucatu region, state of São Paulo.

Eletrofiação e caracterização de membranas biopoliméricas a base de quitosana extraídas dos exoesqueletos de crustáceos

Chitin and chitosan are nontoxic, biodegradable and biocompatible polymers produced by renewable natural sources with applications in diverse areas such as: agriculture, textile, pharmaceutical, cosmetics and biomaterials, such as gels, films and other polymeric membranes. Both have attracted greater interest of scientists and researchers as functional polymeric materials. In this context, the objective of this study was to take advantage of the waste of shrimp (Litopenaeus vannamei and Aristeus antennatus) and crabs (Ucides cordatus) from fairs, beach huts and restaurant in Natal/RN for the extraction of chitin and chitosan for the production of membranes by electrospinning process. The extraction was made through demineralization, deproteinization, deodorization and deacetylation. Morphological analyzes (SEM and XRD), Thermal analysis (TG and DTG), Spectroscopy in the Region of the Infrared with Transformed of Fourier (FTIR) analysis Calorimetry Differential Scanning (DSC) and mechanical tests for traction were performed. In (XRD) the semicrystalline structure of chitosan can be verified while the chitin had higher crystallinity. In the thermal analysis showed a dehydration process followed by decomposition, with similar behavior of carbonized material. Chitosan showed temperature of maximum degradation lower than chitin. In the analysis by Differential Scanning Calorimetry (DSC) the curves were coherent to the thermal events of the chitosan membranes. The results obtained with (DD) for chitosan extracted from Litopenaeus vannamei and Aristeus antennatus shrimp were (80.36 and 71.00%) and Ucides cordatus crabs was 74.65%. It can be observed that, with 70:30 solutions (v/v) (TFA/DCM), 60 and 90% CH3COOH, occurred better facilitate the formation of membranes, while 100:00 (v/v) (TFA/DCM) had formation of agglomerates. In relation to the monofilaments diameters of the chitosan membranes, it was noted that the capillary-collector distance of 10 cm and tensions of 25 and 30 kV contributed to the reduction of the diameters of membranes. It was found that the Young s modulus decreases with increasing concentration of chitosan in the membranes. 90% CH3COOH contributed to the increase in the deformation resulting in more flexible material. The membranes with 5% chitosan 70:30 (v/v) (TFA/DCM) had higher tensile strength

Envelhecimento ambiental acelerado em PRF a base de tecidos híbridos kevlar/vidro: propriedades e instabilidade estrutural

There are a number of damaging mechanisms that various materials can suffer in service. However, when working with polymer composite materials, this is something that requires analysis, especially when exposed to adverse environmental conditions. Thus, the objective of the present thesis is the study of the direct influence of environmental aging and the form of hybridization of the reinforcement woven on the structural stability, surfacedegradation and fracture process of polymer composites laminates. For this, the development of two polymer composite laminates was necessary, where one of them was reinforced with a bi-directional woven with hybrid strandsofkevlar-49/glass-Efibers, and the other also with a bi-directionalwoven, however with weft and warpformed of alternating strandsof Kevlar-49 fibers and glass-E fiber The reinforcementwoven are industrially manufactured. Both laminates use a polyester resin as a matrixand are made up of four layers each. All laminates were industrially prepared by the hand lay-up method of manufacturing. To do this, test specimens were manufactured of the respective laminates and submitted to environmental aging accelerated through the aging chamber. They were exposed to alternating cycles of UV radiation and moisture (heated steam) for a standard defined period. At the end of the exposure period the specimens were subjected to mechanical tests of uniaxial tensile and bending in three points and to the characterizationsof the fracture and surface deterioration. In addition, they were submitted to a structural degradation assessment by the measurement of mass variation technique (MMVT) and the measurement of thickness variation technique (MTVT), this last technique being developed in this thesis. At the end of the analysis it was observed that the form of hybridization of the reinforcement woven and the aging process directly influence with losses or gain in mechanical properties, with losses in the structural degradation and in the formation and propagation of damage mechanism of the developedcomposite laminates