Supermacroporous Polymer-Based Cryogel Bioreactor for Monoclonal Antibody Production in Continuous Culture Using Hybridoma Cells

Cryogel matrices composed of different polymeric blends were synthesized, yielding a unique combination of hydrophilicity and hydrophobicity with the presence or absence of charged surface. Four such cryogel matrices composed of polyacrylamide-chitosan (PAAC), poly(N-isopropylacrylamide)-chitosan, polyacrylonitrile (PAN), and poly(N-isopropylacrylamide) were tested for growth of different hybridoma cell lines and production of antibody in static culture. All the matrices were capable for the adherence of hybridoma cell lines 6A4D7, B7B10, and H9E10 to the polymeric surfaces as well as for the efficient monoclonal antibody (mAb) production. PAAC proved to be relatively better in terms of both mAb production and cell growth. Further, PAAC cryogel was designed into three different formats, monolith, disks, and beads, and used as packing material for packed-bed bioreactor. Longterm cultivation of 6A4D7 cell line on PAAC cryogel scaffold in all the three formats could be successfully done for a period of 6 weeks under static conditions. Continuous packed-bed bioreactor was setup using 6A4D7 hybridoma cell line in the three reactor formats. The reactors ran continuously for a period of 60 days during which mAb production and metabolism of cells in the bioreactors were monitored periodically. The monolith bioreactor performed most efficiently over a period of 60 days and produced a total of 57.5 mg of antibody in the first 30 days (in 500 mL) with a highest concentration of 115 mu g mL(-1), which is fourfold higher than t-flask culture. The results demonstrate that appropriate chemistry and geometry of the bioreactor matrix for cell growth and immobilization can enhance the reactor productivity. (C) 2010 American Institute of Chemical Engineers Biotechnol. Prog., 27: 170-180, 2011

Dynamics of I-asterisk(P-2(1/2)) production inthe ultraviolet photodissociation of alkyn iodides

The relative quantum yields, phi*, for the production of I*(P-2(1/2)) at 266, 280, and similar to 305 nm are reported for a series of primary alkyl iodides using the technique of two-photon laser-induced fluorescence for the detection of I(P-2(3/2)) and I*(P-2(1/2)) atoms. Results are analyzed by invoking the impulsive energy disposal model, which summarizes the dynamics of dissociation as a single parameter. Comparison of our data with those calculated by a more sophisticated time-dependent quantum mechanical model is also made. Near the red edge of the alkyl iodide A band, absorption contribution from the (3)Q(1) state is important and the dynamics near the (3)Q(0)-(1)Q(1) curve-crossing region seem to be influenced by the kinematics of the dissociation process

Plantlet production from shoot tip cultures of red sandalwood ( Pterocarpus santalinus L.)

Red sandalwood (Pterocarpus santalinus L.), belonging to the family Fabaceae, is one of the most valuable trees, and has limited distribution in India. In view of its high price, restricted distribution and usefulness as a timber tree, there is urgent need to obtain improved lines, in both quality and quantity. We have established a method for production of complete plantlets by tissue culture. We report here the successful development of red sandalwood plantlets by induction of multiple shoots from shoot tips, and successful transfer of micropropagated plants to soil.

Production of Dirac particles due to riccion coupling

It has been noted that at high energy the Ricci scalar is manifested in two different ways, as a matter field as well as a geometrical field (which is its usual nature even at low energy). Here, using the material aspect of the Ricci scalar, its interaction with Dirac spinors is considered in four-dimensional curved spacetime. We find that a large number of fermion-antifermion pairs can be produced by the exponential expansion of the early universe.

The precision of regulation in Dictyostelium discoideum: implications for cell-type proportioning in the absence of spatial pattern

We have made careful counts of the exact number of spore, stalk and basal disc cells in small fruiting bodies of Dictyostelium discoideum (undifferentiated amoebae are found only rarely and on average their fraction is 4.96 x 10(-4)). (i) Within aggregates of a given size, the relative apportioning of amoebae to the main cell types occurs with a remarkable degree of precision. In most cases the coefficient of variation (c.v.) in the mean fraction of cells that form spores is within 4.86%. The contribution of stalk and basal disc cells is highly variable when considered separately (c.v.'s upto 25% and 100%, respectively), but markedly less so when considered together. Calculations based on theoretical models indicate that purely cell-autonomous specification of cell, fate cannot account for die observed accuracy of proportioning. Cell-autonomous determination to a prestalk or prespore condition followed by cell type interconversion, and stabilised by feedbacks, suffices to explain the measured accuracy. (ii) The fraction of amoebae that differentiates into spores increases monotonically with the total number of cells. This fraction rises from an average of 73.6% for total cell numbers below 30 and reaches 86.0% for cell numbers between 170 and 200 (it remains steady thereafter at around 86%). Correspondingly, the fraction of amoebae differentiating into stalk or basal disc decreases viith total size. These trends are in accordance with evolutionary expectations and imply that a mechanism for sensing the overall size of the aggregate also plays an essential role in the determination of cell-type proportions.

Production and properties of carbon fibre/particle reinforced cast metal matrix composites

Carbon fibres/particles can be satisfactory reinforcing material in polymer, ceramic and metal matrices. Carbon fibres/particles reinforced polymer matrix composites and ceramic matrix composites are being used extensively in critical areas of application, but carbon fibre - metal matrix composites have not reached that stage yet. This paper discusses the salient aspects of production and specific properties of carbon fibre/particle reinforced cast metal matrix composites. It is envisaged that these materials will find extensive applications where cost, weight and thermal expansion are the key factors.

Production of biosurfactant “Biosur-Pm” by Pseudomonas maltophila CSV89: characterization and role in hydrocarbon uptake

Pseudomonas maltophilia CSV89, a soil bacterium, produces an extracellular biosurfactant, ''Biosur-Pm''. The partially purified product is nondialyzable and chemically composed of 50% protein and 12-15% sugar, which indicates the complex nature of Biosur-Pm. It reduces the surface tension of water from 73 to 53 x 10(-3) N m(-1) and has a critical micellar concentration of 80 mg/l. Compared to aliphatic hydrocarbons, Biosur-Pm shows good activity against aromatic hydrocarbons. The emulsion formed is stable and does not require any metal ions for emulsification. The kinetics of Biosur-Pm production suggest that its synthesis isa growth-associated and pH-dependent process. At pH 7.0, cells produced more Biosur-Pm with less cell surface hydrophobicity. At pH 8.0, however, the cells produced less Biosur-Pm with more cell surface hydrophobicity and showed a twofold higher affinity for aromatic hydrocarbons compared to the cells grown at pH 7.0. The Biosur-Pm showed a pH-dependent release, stimulated growth of the producer strain on mineral salts medium with 1-naphthoic acid when added externally, and facilitated the conversion of salicylate to catechol. All these results suggest that Biosur-Pm is probably a cell-wall component and helps in hydrocarbon assimilation/uptake.

Chopped nonlinear magneto-optic rotation: A technique for precision measurements

We have developed a technique for precise measurement of small magnetic fields using nonlinear magneto-optic rotation (NMOR). The technique relies on the resonant laser beam being chopped. During the on time, the atoms are optically pumped into an aligned ground state (Delta m=2 coherence). During the off time, they freely precess around the magnetic field at the Larmor frequency. If the on-off modulation frequency matches (twice) the Larmor precession frequency, the rotation is resonantly enhanced in every cycle, thereby making the process like a repeated Ramsey measurement of the Larmor frequency. We study chopped-NMOR in a paraffin-coated Cs vapor cell. The out-of-phase demodulated rotation shows a Lorentzian peak of linewidth 85 mu G, corresponding to a sensitivity of 0.15nG/root Hz. We discuss the potential of this technique for the measurement of an atomic electric-dipole moment. Copyright (C) EPLA, 2011

Potential herblayer production and grazing effects in anthropogenic savanna-grasslands in the moist tropical forests of the Western Ghats of India

The moist tropical forests of the Western Ghats of India are pockmarked with savanna-grasslands created and managed by local agricultural communities. A sample of such savanna-grasslands with differing growing conditions was studied in terms of peak above-ground biomass, monthly growth, and cumulative production under different clipping treatments. The herblayer was found to be dominated by perennial C4 grasses, with Eulalia trispicata, Arundinella metzii and Themeda triandra being common to all sites. Peak biomass ranged between 3.3-5.9 t/ha at sites most favourable for grass production. Across these sites, peak biomass was found to be inversely related to the number of rainy days during the growing season, suggesting that growth may be light-limited. This hypothesis is supported by the observation that growth is most rapid immediately after the easing of the monsoon. Single clips early in the growing season had no negative or a slightly positive effect on production, but mid-season single clips or continuous frequent clipping reduced production by as much as 40%. The results suggest that, while indiscriminate grazing may certainly be deleterious, it is possible to obtain sustained high yields from forest lands managed for grass production without totally excluding grazing.

Land availability and biomass production potential in India

In this paper we have assessed the availability of land and the potential for biomass production in India to meet various demands for biomass, including modern bioenergy. This is estimated by considering the various demands on land and its suitability. The biomass production potential of energy plantations is assessed for different agroecological zones. The total woody biomass production is estimated to be 321 Mt, based on biomass productivity in the range 2 to 17 t/ha/yr for the different agro-ecological zones and considering the conservative estimate of 43 Mha land availability for biomass production. A surplus of 231 Mt of biomass (after meeting the increased demand for fuelwood and timber by the year 2010) is estimated to be available for energy, which has an electricity generation potential of 231 TWh. As a first step, only the feasible physical potential of biomass production is assessed, along with an analysis of barriers. The potential costs and benefits of biomass production strategy are not analysed. (C) 1999 Elsevier Science Ltd. All rights reserved.

Regulation of an 8-kDa peptide involved in testosterone production by luteinizing hormone in rat Leydig cells

Results of Western blot analysis carried out with an interstitial cell extract from male guinea pig and ovarian extract from immature female rats administered equine chorionic gonadotropin (eCG) provide supportive evidence to our earlier suggestion that an 8-kDa peptide is involved in acquisition of steroidogenic capacity by the rat Leydig cells. It was found that though the signal was observed in other tissues such as liver, kidney and lung which do not produce gonadal hormones, the peptide was modulated only by lutenizing hormone (LH) in the rat Leydig cells.

I*(P-2(1/2)) production from CH3I photodissociation at 236 nm

The quantum yield of I*((2)p(1/2)) production from CH3I photolysis at 236 nm in the gas phase has been measured as 0.69 +/- 0.03. The implication is that direct excitation to the (1)Q(1) excited state is significant at this wavelength. The dynamics of I* formation at other excitation energies covering the entire A-band of absorption of CH3I has been discussed in the light of this measurement.

The production of AlN-rich matrix composites by the reactive infiltration of Al alloys in nitrogen

Aluminium nitride (AlN)-Al matrices reinforced with Al2O3 particulate have been fabricated by reactive infiltration of Al-2% Mg alloy into Al2O3 preforms in N-2 in the temperature range of 900-1075 degreesC. The growth of composites of useful thickness was facilitated by the presence of a Mg-rich external getter, in the absence of which composite growth is self-limiting and terminates prematurely. Successful growth of composites has been attributed to the reduction in residual oxygen partial pressure brought about by the reaction with oxygen of highly volatile Mg in the getter alloy. The microstructure of the matrix consists of AlN-rich regions contiguous with the particulate with metal-rich channels in-between, thereby suggesting that nitridation initiates by preferential wicking of alloy along the particle surfaces. The increase in nitride content of the matrix with temperature is consistent with hardness values that vary between similar to3 and 10 GPa. (C) 2002 Acta Materialia Inc. Published by Elsevier Science Ltd. All rights reserved.

Sustainable biomass production for energy in selected Asian countries

This paper presents a synthesis of assessment of sustainable biomass production potential in six Asian countries-China, India, Malaysia, Philippines, Sri Lanka and Thailand, and is based on the detailed studies carried out in these countries under the Asian Regional Research Programme in Energy, Environment and Climate (ARRPEEC). National level studies were undertaken to estimate land availability for biomass production, identify and evaluate the biomass production options in terms of yield per hectare and financial viability, estimate sustainable biomass production for energy, and estimate the energy potential of biomass production in the six Asian countries. Sustainable biomass production from plantation is estimated to be in the range of 182.5-210.5, 62-310, 0.4-1.7, 3.7-20.4, 2.0-9.9 and 11.6-106.6 Mt yr(-1) for China, India, Malaysia, Philippines, Sri Lanka and Thailand, respectively. The maximum annual electricity generation potential, using advanced technologies, from the sustainable biomass production is estimated to be about 27, 114, 4.5, 79, 254 and 195 percentage of the total electricity generation in year 2000 in China, India, Malaysia, Philippines, Sri Lanka and Thailand, respectively. Investment cost for bioenergy production varies from US$381 to 1842 ha(-1) in the countries considered in this study; investment cost for production of biomass varies from US$5.1 to 23 t(-1). (C) 2003 Elsevier Ltd. All rights reserved.

New Ventures’ influence on the Growth of SME Employment, Production and Exports in India: Does Institutional Credit matter?

New ventures are considered to be a major source of small firm growth. In Indian context the contribution of new ventures in terms of new employment, production and exports has largely remained unexplored. It is equally important and unexplored, the significance of the contribution of bank credit to the growth of new ventures in India. This paper is an attempt to throw light on these two aspects. The research is based on secondary data of the liberalized period provided by Ministry of Micro, Small and Medium Enterprises, Government of India and Reserve Bank of India. To analyze the influence of bank credit growth on new ventures and the influence of new ventures on growth of additional employment, additional production and additional exports, we used a Bi-Variate Vector Auto Regression. Based on the model generated, Granger causality tests are conducted to obtain the results. The study found that rate of growth of bank credit causes the number of new ventures, implying any increase in the rate of growth of bank credit will be beneficial to the growth of new ventures. The study also concluded that new ventures are not causing the growth of additional employment or additional production. However new ventures cause the growth of additional exports. This is reasonable as entrepreneurs start their new ventures with minimum possible employment and relatively low rate of capacity utilization and they come up to take advantage of the process of globalization by catering to the international market.