Numerical and ExperimentalModelling of Gas Flow and Heat Transfer in the Air Gap of An Electric Machine

This work deals with the cooling of high-speed electric machines, such as motors and generators, through an air gap. It consists of numerical and experimental modelling of gas flow and heat transfer in an annular channel. Velocity and temperature profiles are modelled in the air gap of a high-speed testmachine. Local and mean heat transfer coefficients and total friction coefficients are attained for a smooth rotor-stator combination at a large velocity range. The aim is to solve the heat transfer numerically and experimentally. The FINFLO software, developed at Helsinki University of Technology, has been used in the flow solution, and the commercial IGG and Field view programs for the grid generation and post processing. The annular channel is discretized as a sector mesh. Calculation is performed with constant mass flow rate on six rotational speeds. The effect of turbulence is calculated using three turbulence models. The friction coefficient and velocity factor are attained via total friction power. The first part of experimental section consists of finding the proper sensors and calibrating them in a straight pipe. After preliminary tests, a RdF-sensor is glued on the walls of stator and rotor surfaces. Telemetry is needed to be able to measure the heat transfer coefficients at the rotor. The mean heat transfer coefficients are measured in a test machine on four cooling air mass flow rates at a wide Couette Reynolds number range. The calculated values concerning the friction and heat transfer coefficients are compared with measured and semi-empirical data. Heat is transferred from the hotter stator and rotor surfaces to the coolerair flow in the air gap, not from the rotor to the stator via the air gap, althought the stator temperature is lower than the rotor temperature. The calculatedfriction coefficients fits well with the semi-empirical equations and precedingmeasurements. On constant mass flow rate the rotor heat transfer coefficient attains a saturation point at a higher rotational speed, while the heat transfer coefficient of the stator grows uniformly. The magnitudes of the heat transfer coefficients are almost constant with different turbulence models. The calibrationof sensors in a straight pipe is only an advisory step in the selection process. Telemetry is tested in the pipe conditions and compared to the same measurements with a plain sensor. The magnitudes of the measured data and the data from the semi-empirical equation are higher for the heat transfer coefficients than thenumerical data considered on the velocity range. Friction and heat transfer coefficients are presented in a large velocity range in the report. The goals are reached acceptably using numerical and experimental research. The next challenge is to achieve results for grooved stator-rotor combinations. The work contains also results for an air gap with a grooved stator with 36 slots. The velocity field by the numerical method does not match in every respect the estimated flow mode. The absence of secondary Taylor vortices is evident when using time averagednumerical simulation.

Competitor Information andCompetitive Knowledge Management in a Large Industrial Organization

Thisthesis supplements the systematic approach to competitive intelligence and competitor analysis by introducing an information-processing perspective on management of the competitive environment and competitors therein. The cognitive questions connected to the intelligence process and also the means that organizational actors use in sharing information are discussed. The ultimate aim has been to deepen knowledge of the different intraorganizational processes that are used in acorporate organization to manage and exploit the vast amount of competitor information that is received from the environment. Competitor information and competitive knowledge management is examined as a process, where organizational actorsidentify and perceive the competitive environment by using cognitive simplification, make interpretations resulting in learning and finally utilize competitor information and competitive knowledge in their work processes. The sharing of competitive information and competitive knowledge is facilitated by intraorganizational networks that evolve as a means of developing a shared, organizational level knowledge structure and ensuring that the right information is in the right place at the right time. This thesis approaches competitor information and competitive knowledge management both theoretically and empirically. Based on the conceptual framework developed by theoretical elaboration, further understanding of the studied phenomena is sought by an empirical study. The empirical research was carried out in a multinationally operating forest industry company. This thesis makes some preliminary suggestions of improving the competitive intelligence process. It is concluded that managing competitor information and competitive knowledge is not simply a question of managing information flow or improving sophistication of competitor analysis, but the crucial question to be solved is rather, how to improve the cognitive capabilities connected to identifying and making interpretations of the competitive environment and how to increase learning. It is claimed that competitive intelligence can not be treated like an organizational function or assigned solely to a specialized intelligence unit.

Experimental and Numerical Analysis of Different Volutes in a Centrifugal Compressor

In a centrifugal compressor the flow around the diffuser is collected and led to the pipe system by a spiral-shaped volute. In this study a single-stage centrifugal compressor with three different volutes is investigated. The compressorwas first equipped with the original volute, the cross-section of which was a combination of a rectangle and semi-circle. Next a new volute with a fully circular cross-section was designed and manufactured. Finally, the circular volute wasmodified by rounding the tongue and smoothing the tongue area. The overall performance of the compressor as well as the static pressure distribution after the impeller and on the volute surface were measured. The flow entering the volute was measured using a three-hole Cobra-probe, and flow visualisations were carriedout in the exit cone of the volute. In addition, the radial force acting on theimpeller was measured using magnetic bearings. The complete compressor with thecircular volute (inlet pipe, full impeller, diffuser, volute and outlet pipe) was also modelled using computational fluid dynamics (CFD). A fully 3-D viscous flow was solved using a Navier-Stokes solver, Finflo, developed at Helsinki University of Technology. Chien's k-e model was used to take account of the turbulence. The differences observed in the performance of the different volutes were quite small. The biggest differences were at low speeds and high volume flows,i.e. when the flow entered the volute most radially. In this operating regime the efficiency of the compressor with the modified circular volute was about two percentage points higher than with the other volutes. Also, according to the Cobra-probe measurements and flow visualisations, the modified circular volute performed better than the other volutes in this operating area. The circumferential static pressure distribution in the volute showed increases at low flow, constant distribution at the design flow and decrease at high flow. The non-uniform static pressure distribution of the volute was transmitted backwards across the vaneless diffuser and observed at the impeller exit. At low volume flow a strong two-wave pattern developed into the static pressure distribution at the impeller exit due to the response of the impeller to the non-uniformity of pressure. The radial force of the impeller was the greatest at the choke limit, the smallest atthe design flow, and moderate at low flow. At low flow the force increase was quite mild, whereas the increase at high flow was rapid. Thus, the non-uniformityof pressure and the force related to it are strong especially at high flow. Theforce caused by the modified circular volute was weaker at choke and more symmetric as a function of the volume flow than the force caused by the other volutes.

Theoretical and numerical study of thermomagnetic convection in magnetic fluids

In this thesis, the magnetic field control of convection instabilities and heat and mass transfer processesin magnetic fluids have been investigated by numerical simulations and theoretical considerations. Simulation models based on finite element and finite volume methods have been developed. In addition to standard conservation equations, themagnetic field inside the simulation domain is calculated from Maxwell equations and the necessary terms to take into account for the magnetic body force and magnetic dissipation have been added to the equations governing the fluid motion.Numerical simulations of magnetic fluid convection near the threshold supportedexperimental observations qualitatively. Near the onset of convection the competitive action of thermal and concentration density gradients leads to mostly spatiotemporally chaotic convection with oscillatory and travelling wave regimes, previously observed in binary mixtures and nematic liquid crystals. In many applications of magnetic fluids, the heat and mass transfer processes including the effects of external magnetic fields are of great importance. In addition to magnetic fluids, the concepts and the simulation models used in this study may be applied also to the studies of convective instabilities in ordinary fluids as well as in other binary mixtures and complex fluids.

Project Success through Effective Decisions: Case Studies on Project Goal Setting, Success Evaluation and Managerial Decision Making

The objective of the thesis is to structure and model the factors that contribute to and can be used in evaluating project success. The purpose of this thesis is to enhance the understanding of three research topics. The goal setting process, success evaluation and decision-making process are studied in the context of a project, business unitand its business environment. To achieve the objective three research questionsare posed. These are 1) how to set measurable project goals, 2) how to evaluateproject success and 3) how to affect project success with managerial decisions.The main theoretical contribution comes from deriving a synthesis of these research topics which have mostly been discussed apart from each other in prior research. The research strategy of the study has features from at least the constructive, nomothetical, and decision-oriented research approaches. This strategy guides the theoretical and empirical part of the study. Relevant concepts and a framework are composed on the basis of the prior research contributions within the problem area. A literature review is used to derive constructs of factors withinthe framework. They are related to project goal setting, success evaluation, and decision making. On the basis of this, the case study method is applied to complement the framework. The empirical data includes one product development program, three construction projects, as well as one organization development, hardware/software, and marketing project in their contexts. In two of the case studiesthe analytic hierarchy process is used to formulate a hierarchical model that returns a numerical evaluation of the degree of project success. It has its origin in the solution idea which in turn has its foundation in the notion of projectsuccess. The achieved results are condensed in the form of a process model thatintegrates project goal setting, success evaluation and decision making. The process of project goal setting is analysed as a part of an open system that includes a project, the business unit and its competitive environment. Four main constructs of factors are suggested. First, the project characteristics and requirements are clarified. The second and the third construct comprise the components of client/market segment attractiveness and sources of competitive advantage. Together they determine the competitive position of a business unit. Fourth, the relevant goals and the situation of a business unit are clarified to stress their contribution to the project goals. Empirical evidence is gained on the exploitation of increased knowledge and on the reaction to changes in the business environment during a project to ensure project success. The relevance of a successful project to a company or a business unit tends to increase the higher the reference level of project goals is set. However, normal performance or sometimes performance below this normal level is intentionally accepted. Success measures make project success quantifiable. There are result-oriented, process-oriented and resource-oriented success measures. The study also links result measurements to enablers that portray the key processes. The success measures can be classified into success domains determining the areas on which success is assessed. Empiricalevidence is gained on six success domains: strategy, project implementation, product, stakeholder relationships, learning situation and company functions. However, some project goals, like safety, can be assessed using success measures that belong to two success domains. For example a safety index is used for assessing occupational safety during a project, which is related to project implementation. Product safety requirements, in turn, are connected to the product characteristics and thus to the product-related success domain. Strategic success measures can be used to weave the project phases together. Empirical evidence on their static nature is gained. In order-oriented projects the project phases are oftencontractually divided into different suppliers or contractors. A project from the supplier's perspective can represent only a part of the ¿whole project¿ viewed from the client's perspective. Therefore static success measures are mostly used within the contractually agreed project scope and duration. Proof is also acquired on the dynamic use of operational success measures. They help to focus on the key issues during each project phase. Furthermore, it is shown that the original success domains and success measures, their weights and target values can change dynamically. New success measures can replace the old ones to correspond better with the emphasis of the particular project phase. This adjustment concentrates on the key decision milestones. As a conclusion, the study suggests a combination of static and dynamic success measures. Their linkage to an incentive system can make the project management proactive, enable fast feedback and enhancethe motivation of the personnel. It is argued that the sequence of effective decisions is closely linked to the dynamic control of project success. According to the used definition, effective decisions aim at adequate decision quality and decision implementation. The findings support that project managers construct and use a chain of key decision milestones to evaluate and affect success during aproject. These milestones can be seen as a part of the business processes. Different managers prioritise the key decision milestones to a varying degree. Divergent managerial perspectives, power, responsibilities and involvement during a project offer some explanation for this. Finally, the study introduces the use ofHard Gate and Soft Gate decision milestones. The managers may use the former milestones to provide decision support on result measurements and ad hoc critical conditions. In the latter milestones they may make intermediate success evaluation also on the basis of other types of success measures, like process and resource measures.

Selective catalytic reduction of nitrogen oxides with ammonia in forced unsteady state reactors - Case based reasoning and mathematical model simulation reasoning

The application of forced unsteady-state reactors in case of selective catalytic reduction of nitrogen oxides (NOx) with ammonia (NH3) is sustained by the fact that favorable temperature and composition distributions which cannot be achieved in any steady-state regime can be obtained by means of unsteady-state operations. In a normal way of operation the low exothermicity of the selective catalytic reduction (SCR) reaction (usually carried out in the range of 280-350°C) is not enough to maintain by itself the chemical reaction. A normal mode of operation usually requires supply of supplementary heat increasing in this way the overall process operation cost. Through forced unsteady-state operation, the main advantage that can be obtained when exothermic reactions take place is the possibility of trapping, beside the ammonia, the moving heat wave inside the catalytic bed. The unsteady state-operation enables the exploitation of the thermal storage capacity of the catalyticbed. The catalytic bed acts as a regenerative heat exchanger allowing auto-thermal behaviour when the adiabatic temperature rise is low. Finding the optimum reactor configuration, employing the most suitable operation model and identifying the reactor behavior are highly important steps in order to configure a proper device for industrial applications. The Reverse Flow Reactor (RFR) - a forced unsteady state reactor - corresponds to the above mentioned characteristics and may be employed as an efficient device for the treatment of dilute pollutant mixtures. As a main disadvantage, beside its advantages, the RFR presents the 'wash out' phenomena. This phenomenon represents emissions of unconverted reactants at every switch of the flow direction. As a consequence our attention was focused on finding an alternative reactor configuration for RFR which is not affected by the incontrollable emissions of unconverted reactants. In this respect the Reactor Network (RN) was investigated. Its configuration consists of several reactors connected in a closed sequence, simulating a moving bed by changing the reactants feeding position. In the RN the flow direction is maintained in the same way ensuring uniformcatalyst exploitation and in the same time the 'wash out' phenomena is annulated. The simulated moving bed (SMB) can operate in transient mode giving practically constant exit concentration and high conversion levels. The main advantage of the reactor network operation is emphasizedby the possibility to obtain auto-thermal behavior with nearly uniformcatalyst utilization. However, the reactor network presents only a small range of switching times which allow to reach and to maintain an ignited state. Even so a proper study of the complex behavior of the RN may give the necessary information to overcome all the difficulties that can appear in the RN operation. The unsteady-state reactors complexity arises from the fact that these reactor types are characterized by short contact times and complex interaction between heat and mass transportphenomena. Such complex interactions can give rise to a remarkable complex dynamic behavior characterized by a set of spatial-temporal patterns, chaotic changes in concentration and traveling waves of heat or chemical reactivity. The main efforts of the current research studies concern the improvement of contact modalities between reactants, the possibility of thermal wave storage inside the reactor and the improvement of the kinetic activity of the catalyst used. Paying attention to the above mentioned aspects is important when higher activity even at low feeding temperatures and low emissions of unconverted reactants are the main operation concerns. Also, the prediction of the reactor pseudo or steady-state performance (regarding the conversion, selectivity and thermal behavior) and the dynamicreactor response during exploitation are important aspects in finding the optimal control strategy for the forced unsteady state catalytic tubular reactors. The design of an adapted reactor requires knowledge about the influence of its operating conditions on the overall process performance and a precise evaluation of the operating parameters rage for which a sustained dynamic behavior is obtained. An apriori estimation of the system parameters result in diminution of the computational efforts. Usually the convergence of unsteady state reactor systems requires integration over hundreds of cycles depending on the initial guess of the parameter values. The investigation of various operation models and thermal transfer strategies give reliable means to obtain recuperative and regenerative devices which are capable to maintain an auto-thermal behavior in case of low exothermic reactions. In the present research work a gradual analysis of the SCR of NOx with ammonia process in forced unsteady-state reactors was realized. The investigation covers the presentationof the general problematic related to the effect of noxious emissions in the environment, the analysis of the suitable catalysts types for the process, the mathematical analysis approach for modeling and finding the system solutions and the experimental investigation of the device found to be more suitable for the present process. In order to gain information about the forced unsteady state reactor design, operation, important system parameters and their values, mathematical description, mathematicalmethod for solving systems of partial differential equations and other specific aspects, in a fast and easy way, and a case based reasoning (CBR) approach has been used. This approach, using the experience of past similarproblems and their adapted solutions, may provide a method for gaining informations and solutions for new problems related to the forced unsteady state reactors technology. As a consequence a CBR system was implemented and a corresponding tool was developed. Further on, grooving up the hypothesis of isothermal operation, the investigation by means of numerical simulation of the feasibility of the SCR of NOx with ammonia in the RFRand in the RN with variable feeding position was realized. The hypothesis of non-isothermal operation was taken into account because in our opinion ifa commercial catalyst is considered, is not possible to modify the chemical activity and its adsorptive capacity to improve the operation butis possible to change the operation regime. In order to identify the most suitable device for the unsteady state reduction of NOx with ammonia, considering the perspective of recuperative and regenerative devices, a comparative analysis of the above mentioned two devices performance was realized. The assumption of isothermal conditions in the beginningof the forced unsteadystate investigation allowed the simplification of the analysis enabling to focus on the impact of the conditions and mode of operation on the dynamic features caused by the trapping of one reactant in the reactor, without considering the impact of thermal effect on overall reactor performance. The non-isothermal system approach has been investigated in order to point out the important influence of the thermal effect on overall reactor performance, studying the possibility of RFR and RN utilization as recuperative and regenerative devices and the possibility of achieving a sustained auto-thermal behavior in case of lowexothermic reaction of SCR of NOx with ammonia and low temperature gasfeeding. Beside the influence of the thermal effect, the influence of the principal operating parameters, as switching time, inlet flow rate and initial catalyst temperature have been stressed. This analysis is important not only because it allows a comparison between the two devices and optimisation of the operation, but also the switching time is the main operating parameter. An appropriate choice of this parameter enables the fulfilment of the process constraints. The level of the conversions achieved, the more uniform temperature profiles, the uniformity ofcatalyst exploitation and the much simpler mode of operation imposed the RN as a much more suitable device for SCR of NOx with ammonia, in usual operation and also in the perspective of control strategy implementation. Theoretical simplified models have also been proposed in order to describe the forced unsteady state reactors performance and to estimate their internal temperature and concentration profiles. The general idea was to extend the study of catalytic reactor dynamics taking into account the perspectives that haven't been analyzed yet. The experimental investigation ofRN revealed a good agreement between the data obtained by model simulation and the ones obtained experimentally.

Fishery of the Goliath grouper, Epinephelus itajara (Teleostei: Epinephelidae) based on local ecological knowledge and fishery records in Yucatan, Mexico

The Goliath grouper, Epinephelus itajara, a large-bodied (similar to 2.5 m TL, > 400 kg) and critically endangered fish (Epinephelidae), is highly Vulnerable to overfishing. Although protected from fishing in many countries, its exploitation in Mexico is unregulated; a situation that puts its populations at risk. Fishery records of E. itajara are scarce, which prevents determination of its fishery status. This work aimed to elucidate the E itajara fishery in the northern Yucatan Peninsula by 1) analyzing available catch records and 2) interviewing veteran fishermen (local ecological knowledge) from two traditional landing sites: Dzilam de Bravo and Puerto Progreso. Historic fishery records from two fishing cooperatives were analyzed in order to elucidate the current situation and offer viable alternatives for conservation and management. Catches have decreased severely. Local knowledge obtained from fishermen represented a very important source of information for reconstructing the fisheries history of this species. Conservation measures that incorporate regional and international regulations on critically endangered fish species are suggested

Impacts of upland open drains upon runoff generation: a numerical assessment of catchment-scale impacts

Shallow upland drains, grips, have been hypothesized as responsible for increased downstream flow magnitudes. Observations provide counterfactual evidence, often relating to the difficulty of inferring conclusions from statistical correlation and paired catchment comparisons, and the complexity of designing field experiments to test grip impacts at the catchment scale. Drainage should provide drier antecedent moisture conditions, providing more storage at the start of an event; however, grips have higher flow velocities than overland flow, thus potentially delivering flow more rapidly to the drainage network. We develop and apply a model for assessing the impacts of grips on flow hydrographs. The model was calibrated on the gripped case, and then the gripped case was compared with the intact case by removing all grips. This comparison showed that even given parameter uncertainty, the intact case had significantly higher flood peaks and lower baseflows, mirroring field observations of the hydrological response of intact peat. The simulations suggest that this is because delivery effects may not translate into catchment-scale impacts for three reasons. First, in our case, the proportions of flow path lengths that were hillslope were not changed significantly by gripping. Second, the structure of the grip network as compared with the structure of the drainage basin mitigated against grip-related increases in the concentration of runoff in the drainage network, although it did marginally reduce the mean timing of that concentration at the catchment outlet. Third, the effect of the latter upon downstream flow magnitudes can only be assessed by reference to the peak timing of other tributary basins, emphasizing that drain effects are both relative and scale dependent. However, given the importance of hillslope flow paths, we show that if upland drainage causes significant changes in surface roughness on hillslopes, then critical and important feedbacks may impact upon the speed of hydrological response. Copyright (c) 2012 John Wiley & Sons, Ltd.

Análisis del discurso colaborativo en el entorno Knowledge Forum: categorización de los mensajes

El objetivo de esta investigación es conocer la tipología de aportaciones, que se producen en el entorno virtual colaborativo Knowledge Forum y comprobar si está teniendo lugar un aprendizaje colaborativo a través del ordenador (CSCL). Las contribuciones a los diferentes 30 foros han sido analizados y categorizados usando un esquema de codificación en base a las scaffolds o andamiajes que dicho entorno proporciona. Los resultados muestran que en conjunto los 308 estudiantes universitarios aportan nueva información y opinan, pero hay escasez de mensajes con diferentes opiniones que lleven a la discusión y a intercambios de puntos de vista distintos.

Analysing knowledge building: usages, achievements and limits of forums at university

This paper aims to explore asynchronous communication in computer supported collaborative learning (CSCL). Thirty virtual forums are analysed in both a quantitative and a qualitative way. Quantitatively, the number of messages written, message threads and original and answer messages are counted. Qualitatively, the content of the notes is analysed, cataloguing these into two different levels: on the one hand, as a set of knowledge building process categories, and on the other hand, following the scaffolds that Knowledge Forum offers. The results show that both an exchange of information and a collaborative work take place. Nevertheless, the construction of knowledge is superficial.

Evaluation of the Development of Metacognitive Knowledge Supported by the KnowCat System

The aim of this study was to examine the development of the metacognitive knowledge of a group of higher education students who participated actively in an experiment based on a Computer Supported Collaborative Learning environment called KnowCat. Eighteen university students participated in a 12-month learning project during which the KnowCat learning environment was used to support scaffolding process among equals during problem-solving tasks. After using KnowCat, the students were interviewed over their work in this shared workspace. Qualitative analysis revealed that the educational application of KnowCat can favour and improve the development of metacognitive knowledge.

Informe d'Autors UOC a ISI Web of Knowledge. Juny 2014

UOC

Informe d'Autors UOC a ISI Web of Knowledge. Juliol 2014

UOC

Exploring transparent approaches to the authentication of signatures on artwork

This thesis is composed of three main parts. The first consists of a state of the art of the different notions that are significant to understand the elements surrounding art authentication in general, and of signatures in particular, and that the author deemed them necessary to fully grasp the microcosm that makes up this particular market. Individuals with a solid knowledge of the art and expertise area, and that are particularly interested in the present study are advised to advance directly to the fourth Chapter. The expertise of the signature, it's reliability, and the factors impacting the expert's conclusions are brought forward. The final aim of the state of the art is to offer a general list of recommendations based on an exhaustive review of the current literature and given in light of all of the exposed issues. These guidelines are specifically formulated for the expertise of signatures on paintings, but can also be applied to wider themes in the area of signature examination. The second part of this thesis covers the experimental stages of the research. It consists of the method developed to authenticate painted signatures on works of art. This method is articulated around several main objectives: defining measurable features on painted signatures and defining their relevance in order to establish the separation capacities between groups of authentic and simulated signatures. For the first time, numerical analyses of painted signatures have been obtained and are used to attribute their authorship to given artists. An in-depth discussion of the developed method constitutes the third and final part of this study. It evaluates the opportunities and constraints when applied by signature and handwriting experts in forensic science. A brief summary covering each chapter allows a rapid overview of the study and summarizes the aims and main themes of each chapter. These outlines presented below summarize the aims and main themes addressed in each chapter. Part I - Theory Chapter 1 exposes legal aspects surrounding the authentication of works of art by art experts. The definition of what is legally authentic, the quality and types of the experts that can express an opinion concerning the authorship of a specific painting, and standard deontological rules are addressed. The practices applied in Switzerland will be specifically dealt with. Chapter 2 presents an overview of the different scientific analyses that can be carried out on paintings (from the canvas to the top coat). Scientific examinations of works of art have become more common, as more and more museums equip themselves with laboratories, thus an understanding of their role in the art authentication process is vital. The added value that a signature expertise can have in comparison to other scientific techniques is also addressed. Chapter 3 provides a historical overview of the signature on paintings throughout the ages, in order to offer the reader an understanding of the origin of the signature on works of art and its evolution through time. An explanation is given on the transitions that the signature went through from the 15th century on and how it progressively took on its widely known modern form. Both this chapter and chapter 2 are presented to show the reader the rich sources of information that can be provided to describe a painting, and how the signature is one of these sources. Chapter 4 focuses on the different hypotheses the FHE must keep in mind when examining a painted signature, since a number of scenarios can be encountered when dealing with signatures on works of art. The different forms of signatures, as well as the variables that may have an influence on the painted signatures, are also presented. Finally, the current state of knowledge of the examination procedure of signatures in forensic science in general, and in particular for painted signatures, is exposed. The state of the art of the assessment of the authorship of signatures on paintings is established and discussed in light of the theoretical facets mentioned previously. Chapter 5 considers key elements that can have an impact on the FHE during his or her2 examinations. This includes a discussion on elements such as the skill, confidence and competence of an expert, as well as the potential bias effects he might encounter. A better understanding of elements surrounding handwriting examinations, to, in turn, better communicate results and conclusions to an audience, is also undertaken. Chapter 6 reviews the judicial acceptance of signature analysis in Courts and closes the state of the art section of this thesis. This chapter brings forward the current issues pertaining to the appreciation of this expertise by the non- forensic community, and will discuss the increasing number of claims of the unscientific nature of signature authentication. The necessity to aim for more scientific, comprehensive and transparent authentication methods will be discussed. The theoretical part of this thesis is concluded by a series of general recommendations for forensic handwriting examiners in forensic science, specifically for the expertise of signatures on paintings. These recommendations stem from the exhaustive review of the literature and the issues exposed from this review and can also be applied to the traditional examination of signatures (on paper). Part II - Experimental part Chapter 7 describes and defines the sampling, extraction and analysis phases of the research. The sampling stage of artists' signatures and their respective simulations are presented, followed by the steps that were undertaken to extract and determine sets of characteristics, specific to each artist, that describe their signatures. The method is based on a study of five artists and a group of individuals acting as forgers for the sake of this study. Finally, the analysis procedure of these characteristics to assess of the strength of evidence, and based on a Bayesian reasoning process, is presented. Chapter 8 outlines the results concerning both the artist and simulation corpuses after their optical observation, followed by the results of the analysis phase of the research. The feature selection process and the likelihood ratio evaluation are the main themes that are addressed. The discrimination power between both corpuses is illustrated through multivariate analysis. Part III - Discussion Chapter 9 discusses the materials, the methods, and the obtained results of the research. The opportunities, but also constraints and limits, of the developed method are exposed. Future works that can be carried out subsequent to the results of the study are also presented. Chapter 10, the last chapter of this thesis, proposes a strategy to incorporate the model developed in the last chapters into the traditional signature expertise procedures. Thus, the strength of this expertise is discussed in conjunction with the traditional conclusions reached by forensic handwriting examiners in forensic science. Finally, this chapter summarizes and advocates a list of formal recommendations for good practices for handwriting examiners. In conclusion, the research highlights the interdisciplinary aspect of signature examination of signatures on paintings. The current state of knowledge of the judicial quality of art experts, along with the scientific and historical analysis of paintings and signatures, are overviewed to give the reader a feel of the different factors that have an impact on this particular subject. The temperamental acceptance of forensic signature analysis in court, also presented in the state of the art, explicitly demonstrates the necessity of a better recognition of signature expertise by courts of law. This general acceptance, however, can only be achieved by producing high quality results through a well-defined examination process. This research offers an original approach to attribute a painted signature to a certain artist: for the first time, a probabilistic model used to measure the discriminative potential between authentic and simulated painted signatures is studied. The opportunities and limits that lie within this method of scientifically establishing the authorship of signatures on works of art are thus presented. In addition, the second key contribution of this work proposes a procedure to combine the developed method into that used traditionally signature experts in forensic science. Such an implementation into the holistic traditional signature examination casework is a large step providing the forensic, judicial and art communities with a solid-based reasoning framework for the examination of signatures on paintings. The framework and preliminary results associated with this research have been published (Montani, 2009a) and presented at international forensic science conferences (Montani, 2009b; Montani, 2012).