Performance Improvement of Centrifugal Compressor Stage with Pinched Geometry or Vaned Diffuser

Centrifugal compressors are widely used for example in refrigeration processes, the oil and gas industry, superchargers, and waste water treatment. In this work, five different vaneless diffusers and six different vaned diffusers are investigated numerically. The vaneless diffusers vary only by their diffuser width, so that four of the geometries have pinch implemented to them. Pinch means a decrease in the diffuser width. Four of the vaned diffusers have the same vane turning angle and a different number of vanes, and two have different vane turning angles. The flow solver used to solve the flow fields is Finflo, which is a Navier-Stokes solver. All the cases are modeled with the Chien's k – έ- turbulence model, and selected cases are modeled also with the k – ώ-SST turbulence model. All five vaneless diffusers and three vaned diffusers are investigated also experimentally. For each construction, the compressor operating map is measured according to relevant standards. In addition to this, the flow fields before and after the diffuser are measured with static and total pressure, flow angle and total temperature measurements. When comparing the computational results to the measured results, it is evident that the k – ώ-SST turbulence model predicts the flow fields better. The simulation results indicate that it is possible to improve the efficiency with the pinch, and according to the numerical results, the two best geometries are the ones with most pinch at the shroud. These geometries have approximately 4 percentage points higher efficiency than the unpinched vaneless diffusers. The hub pinch does not seem to have any major benefits. In general, the pinches make the flow fields before and after the diffuser more uniform. The pinch also seems to improve the impeller efficiency. This is down to two reasons. The major reason is that the pinch decreases the size of slow flow and possible backflow region located near the shroud after the impeller. Secondly, the pinches decrease the flow velocity in the tip clearance, leading to a smaller tip leakage flow and therefore slightly better impeller efficiency. Also some of the vaned diffusers improve the efficiency, the increment being 1...3 percentage points, when compared to the vaneless unpinched geometry. The measurement results confirm that the pinch is beneficial to the performance of the compressor. The flow fields are more uniform with the pinched cases, and the slow flow regions are smaller. The peak efficiency is approximately 2 percentage points and the design point efficiency approximately 4 percentage points higher with the pinched geometries than with the un- pinched geometry. According to the measurements, the two best geometries are the ones with the most pinch at the shroud, the case with the pinch only at the shroud being slightly better of the two. The vaned diffusers also have better efficiency than the vaneless unpinched geometries. However, the pinched cases have even better efficiencies. The vaned diffusers narrow the operating range considerably, whilst the pinch has no significant effect on the operating range.

Marcos da história da radioatividade e tendências atuais

The first days of radioactivity, the discoveries of X-rays, radioactivity, of alpha- and beta- particles and gamma- radiation, of new radioactive elements, of artificial radioactivity, the neutron and positron and nuclear fission are reviewed as well as several adverse historical marks, such as the Manhattan project and some nuclear and radiological accidents. Nuclear energy generation in Brazil and the world, as an alternative to minimize environmental problems, is discussed, as are the medicinal, industrial and food applications of ionizing radiation. The text leads the reader to reflect on the subject and to consider its various aspects with scientific and technological maturity.

Descrições estruturais cristalinas de zeólitos

Crystalline structures of zeolites can be studied using different representations: the internal symmetry obtained by X-Ray or neutron diffraction crystallography techniques or a systematic analysis of the basic structural units which can be arranged to build the geometries of each kind of zeolite. In this work the basic concepts of three building units, SBU (Secondary Building Units), SSU (Structural SubUnits) and PBU (Periodic Building Units) are presented. The properties of the resulting crystalline structures are discussed (pores, cavities, channels), describing the influence of each one of these properties in processes of physical-chemical interest. Representative case studies of known zeolite crystalline structures are also discussed in terms of their space group classification.

Composição elementar do material particulado presente no aerossol atmosférico do município de Sete Lagoas, Minas Gerais

The main objective of this study was the identification of sources generating particulate matter in the atmospheric aerosols of Sete Lagoas, Minas Gerais. The measurement of the mineral composition was accomplished by X-ray diffractometry and the elemental concentration by neutron activation analysis. The results showed that Al, Cl, Cu, Fe, K, Mg and Na are the predominant chemical elements in the total suspended particles (TPS). The presence of Na, Ba, Cl, Cu, Eu, Fe and Sm in those particles with aerodynamic diameter smaller than 10 µm (PM10), indicates that soil dust and ceramic and pig iron industries are the main sources of air quality degradation in the region.

Teores de nitrato (NO3-) e amônio (NH4+) nas águas do aqüífero Barreiras nos bairros do Reduto, Nazaré e Umarizal - Belém/PA

This paper evaluates the occurrence of nitrate and ammonium in the Barreiras aquifer in the metropolitan area of Belém, Pará State, Brazil. The results show that some wells display ammonium and nitrate concentrations above or close to the limits of water potability regulations. The main cause of the pollution of these waters is related the local disposal of domestic effluents and/or leakage from pipes of old sewage systems.

Efeitos da poluição atmosférica (litorânea e industrial) em isoladores da rede elétrica da região metropolitana de Salvador

The performances of eight kinds of insulators from electrical distribution lines in Salvador-BA, Brazil, were evaluated considering the chemical and physical local environmental pollution. The parameters that were chosen as characteristic for the insulators' properties were leakage current and partial electrical discharge. A data storage processing system and a communication link to the lab were built for data acquisition. The results show that the main contribution to the poor performance of the insulators is settleable magnetite particulate matter on the insulator in addition to the long term wetness time, t4.

Concentrated Winding Multiphase Permanent Magnet Machine Design and Electromagnetic Properties – Case Axial Flux Machine

Concentrated winding permanent magnet machines and their electromagnetic properties are studied in this doctoral thesis. The thesis includes a number of main tasks related to the application of permanent magnets in concentrated winding open slot machines. Suitable analytical methods are required for the first design calculations of a new machine. Concentrated winding machines differ from conventional integral slot winding machines in such a way that adapted analytical calculation methods are needed. A simple analytical model for calculating the concentrated winding axial flux machines is provided. The next three main design tasks are discussed in more detail in the thesis. The magnetic length of the rotor surface magnet machines is studied, and it is shown that the traditional methods have to be modified also in this respect. An important topic in this study has been to evaluate and minimize the rotor permanent magnet Joule losses by using segmented magnets in the calculations and experiments. Determination of the magnetizing and leakage inductances for a concentrated winding machine and the torque production capability of concentrated winding machines with different pole pair numbers are studied, and the results are compared with the corresponding properties of integral slot winding machines. The thesis introduces a new practical permanent magnet motor type for industrial use. The special features of the machine are based on the option of using concentrated winding open slot constructions of permanent magnet synchronous machines in the normal speed ranges of industrial motors, for instance up to 3000 min-1, without excessive rotor losses. By applying the analytical equations and methods introduced in the thesis, a 37 kW 2400 min-1 12-slot 10-pole axial flux machine with rotor-surfacemounted magnets is designed. The performance of the designed motor is determined by experimental measurements and finite element calculations.

Determinação de paládio em amostras biológicas aplicando técnicas analíticas nucleares

This study presents Pd determinations in bovine tissue samples containing palladium prepared in the laboratory, and CCQM-P63 automotive catalyst materials of the Proficiency Test, using instrumental thermal and epithermal neutron activation analysis and energy dispersive X-ray fluorescence techniques. Solvent extraction and solid phase extraction procedures were also applied to separate Pd from interfering elements before the irradiation in the nuclear reactor. The results obtained by different techniques were compared against each other to examine sensitivity, precision and accuracy.

Avaliação da biodegradação de matrizes porosas à base de hidroxiapatita para aplicação como fontes radioativas em braquiterapia

Porous ceramic materials based on calcium phosphate compounds (CPC) have been studied aiming at different biomedical applications such as implants, drug delivery systems and radioactive sources for brachytherapy. Two kinds of hydroxyapatite (HAp) powders and their ceramic bodies were characterized by a combination of different techniques (XRF, BET method, SEM, ICP/AES and neutron activation analysis - NAA) to evaluate their physico-chemical and microstructural characteristics in terms of chemical composition, segregated phases, microstructure, porosity, chemical and thermal stability, biodegradation and incorporation of substances in their structures. The results revealed that these systems presented potential for use as porous biodegradable radioactive sources able to be loaded with a wide range of radionuclides for cancer treatment by the brachytherapy technique.

Núcleos exóticos e síntese dos elementos químicos

We have around ninety chemical elements available in nature, which were produced mainly by nuclear reactions inside stars. The fusion reactions are the main synthesis process which generates the light and intermediate masses elements. The synthesis begins with the hydrogen burning reaching the region of iron mass nuclei. Heavier elements are synthesized by neutron capture processes, forming exotic nuclei with large neutron excess. These systems present characteristics very different from nuclei inside of stable atoms; they only occur in particular astrophysical environments or are produced artificially in special laboratory conditions. This work discusses some properties of the exotic nuclei and how they participate in the synthesis of elements.

UDP-N-acetilglicosamina enolpiruvil transferase: determinação dos estados de protonação de resíduos de aminoácidos do sítio ativo pelo método PM6

UDP-N-acetylglucosamine-enolpyruvyl transferase (MurA) catalyzes the reaction between phosphoenol pyruvate and UDP-N-acetylglucosamine. We present a theoretical approach using the semiempirical PM6 method for defining protonation state of three active site residues, K22, H125, and K160. Prior comparison with neutron diffraction data showed that PM6 accurately predicted protonation states of active site residues of b-trypsin and D-xylose isomerase. Using the same methodology with MurA crystallographic data, we conclude that when reaction intermediate is located at the active site, H125 and K22 are in protonated form and K160 in neutral form.

CÉLULAS SOLARES SENSIBILIZADAS POR CORANTES NATURAIS: UM EXPERIMENTO INTRODUTÓRIO SOBRE ENERGIA RENOVÁVEL PARA ALUNOS DE GRADUAÇÃO

An interesting practical experiment about the preparation of dye–sensitized solar cells (DSSC) using natural dyes were carried out by the undergraduate students in the chemistry course at UNICAMP . Natural dyes were extracted from blueberries (Vaccinium myrtillus L.), jabuticabas (Myrciaria cauliflora), raw and cooked beets (Beta vulgaris L.), and annattos (Bixa orellana L.), which were used to sensitize TiO2 films that composed the photoanode in the DSSC. A polymer electrolyte containing an iodide/triiodide redox couple was used in lieu of the use of liquid solutions to prevent any leakage in the devices. A maximum solar-to-electric energy conversion of 0.26 ± 0.02% was obtained for the solar cell prepared with annatto extracts. This experiment was an effective way to illustrate to the undergraduate students how to apply some of the chemical concepts that they learned during their chemistry course to produce electric energy from a clean and renewable energy source. Teachers could also exploit the basics of the electronic transitions in inorganic and organic compounds (e.g., metal-to-ligand charge transfer and ϖ-ϖ* transitions), thermodynamics (e.g., Gibbs free energy), acid–base reactions in the oxide solid surface and electrolyte, and band theory (i.e., the importance of the Fermi level energy).

Teollisuuden jäähdytysjärjestelmät. Case: Kaasunerotuslaitteiston evaluointi

Teollisuuden jäähdytysjärjestelmiä tarvitaan prosessien lämpötilan ja paineen hal-litsemiseen. Vesi on käytetyin lämmönsiirtoaine hyvän saatavuutensa, halvan hin-nan ja korkean lämmönsiirtokyvyn ansiosta. Jäähdytysjärjestelmät jaetaan kolmeen päätyyppiin, joita ovat läpivirtausjäähdytys, suljettu ja avoin kiertojäähdytys. Kullakin järjestelmätyypillä on tyypilliset alatyyppinsä. Avoimella kiertojär-jestelmällä on eniten alatyyppejä, joista yleisin on jäähdytystorni. Jäähdytystorneja on kolmea tyyppiä: märkä-, kuiva ja hybriditorni. Kullakin järjestelmätyypillä on ominaiset piirteensä käyttökohteiden, ympäristövaikutusten, ohjattavuuden, investointi- ja käyttökulujen suhteen, joita tässä työssä esitellään. Työssä tutkitaan teollisuuden jäähdytysjärjestelmien esittelyn lisäksi erään ali-painekaasunpoistimen soveltuvuutta suljetun kiertojäähdytysjärjestelmän kaasun-poistoon. Suljettuun kiertojäähdytysjärjestelmään jää ilmaa täyttövaiheessa ja kul-keutuu liuenneena käytettävän jäähdytysveden mukana. Muodostuva ylikylläinen seos synnyttää veden sekaan ilmakuplia, jotka aiheuttavat korroosiota kemiallisesti ja kuluttamalla. Lisäksi kaasukuplat vievät tilavuutta nesteeltä. Tämä pienentää järjestelmän jäähdytystehoa merkittävästi, koska kaasun lämmönsiirtokyky verrat-tuna veden lämmönsiirtokykyyn on pieni. Työssä esitellään myös muita mahdolli-sia suljetun järjestelmän kaasulähteitä ja niiden aiheuttamia ongelmia. Alipainekaasunpoistimen kaasunerotustehokkuutta mitattiin jäähdytysvesinäyttei-den selkeytymisnopeudella ja lämmönsiirtimien tehon paranemisella. Kahden viikon tarkastelujaksolla selkeytymisajat paranivat 36–60 % eri mittauspaikoissa ja lämmönsiirtimien tehot paranivat 6–29 %. Järjestelmään kuitenkin jäi merkittävä määrä kaasua, vaikka laitteen käyttöä jatkettiin tarkastelujakson jälkeen, joten tavoitteisiin ei päästy. Tutkitun alipainekaasunpoistolaitteen ei todettu soveltuvan tehdasympäristöön kestämättömyyden, hankalakäyttöisyyden ja tehottomuuden takia. Tulokset kuitenkin osoittavat, että kaasunerotuksella on merkittävä vaikutus suljetun jäähdytysjärjestelmän toimivuuteen ja saavutettavaan jäähdytystehoon.

Kuituvuoto reikäsihdillä massan syöttövaiheessa

Diplomityön tarkoituksena oli kehittää tutkimuslaite, jolla pystyttäisiin tutkimaan sellumassan syöttötapahtumaa reikäsihdillä ja tarkastelemaan syöttöhetkellä tapahtuvaa kuituhäviötä. Laitteen suunnittelun ja valmistuksen tavoitteena oli myös saada tutkimuslaite mahdollisim-man modifioitavaksi (syöttöaukon koko, muoto ja erityyppiset reikäsihdit ja näiden vaikutukset sellukuitujen hävikkiin). Haluttiin myös mahdollisuus syöttötapahtuman kuvaamiseen esim. suurnopeuskameroin, joka otettiinkin huomioon laiteosia valittaessa (läpinäkyvä akryyli). Tutkimuslaitteen kestävyyttä erilaisissa prosessiolosuhteissa haluttiin korostaa (voidaan operoida laajalla pH ja lämpötila-alueilla, sekä syöttöpainetta voidaan muunnella). Diplomityön kirjallisuusosassa käsitellään kuituvuodon aiheuttamia haittoja, joista tärkein on taloudellinen menetys. Näiden lisäksi kirjallisuusosassa tarkastellaan pääpirteittäin pesume-netelmiä ja käydään läpi kuitusulpun suotautumiseen vaikuttavia tekijöitä. Diplomityöhön sisältyi tutkimuslaitteen suunnittelun ja valmistuksen lisäksi myös laitteen toi-mivuuden testaus. Testit suoritettiin pohjoismaisella koivusellulla. Koivusellu otettiin happi-vaiheen jälkeisen pesurin poistosta. Massalle suoritettiin KAPPA-luvun, SR-luvun, viskositee-tin ja syrjäytys -määritykset, sekä kuituanalyysi. Laitteella suoritettiin 7 %, 10 % ja 12 % sakeuksisten massojen koeajotestit. Suodokset otettiin talteen jatkotutkimuksiin, jossa niistä mitattiin kuituvuoto. 10 % suodokselle suoritettiin myös kuituanalyysi. Tuloksista nähtiin, että 7 % sakeuksinen massa antoi lähes nelinkertaisen kuituvuotomäärän 10 % sakeuksiseen massan syöttöön nähden.

Design Aspects of Megawatt-Range Direct-Driven Permanent MagnetWind Generators

Direct-driven permanent magnet synchronous generator is one of the most promising topologies for megawatt-range wind power applications. The rotational speed of the direct-driven generator is very low compared with the traditional electrical machines. The low rotational speed requires high torque to produce megawatt-range power. The special features of the direct-driven generators caused by the low speed and high torque are discussed in this doctoral thesis. Low speed and high torque set high demands on the torque quality. The cogging torque and the load torque ripple must be as low as possible to prevent mechanical failures. In this doctoral thesis, various methods to improve the torque quality are compared with each other. The rotor surface shaping, magnet skew, magnet shaping, and the asymmetrical placement of magnets and stator slots are studied not only by means of torque quality, but also the effects on the electromagnetic performance and manufacturability of the machine are discussed. The heat transfer of the direct-driven generator must be designed to handle the copper losses of the stator winding carrying high current density and to keep the temperature of the magnets low enough. The cooling system of the direct-driven generator applying the doubly radial air cooling with numerous radial cooling ducts was modeled with a lumped-parameter-based thermal network. The performance of the cooling system was discussed during the steady and transient states. The effect of the number and width of radial cooling ducts was explored. The large number of radial cooling ducts drastically increases the impact of the stack end area effects, because the stator stack consists of numerous substacks. The effects of the radial cooling ducts on the effective axial length of the machine were studied by analyzing the crosssection of the machine in the axial direction. The method to compensate the magnet end area leakage was considered. The effect of the cooling ducts and the stack end area effects on the no-load voltages and inductances of the machine were explored by using numerical analysis tools based on the three-dimensional finite element method. The electrical efficiency of the permanent magnet machine with different control methods was estimated analytically over the whole speed and torque range. The electrical efficiencies achieved with the most common control methods were compared with each other. The stator voltage increase caused by the armature reaction was analyzed. The effect of inductance saturation as a function of load current was implemented to the analytical efficiency calculation.