1000 resultados para Impulsos de terras
Resumo:
A stir bar sorptive extraction with liquid desorption followed by large volume injection coupled to gas chromatography–quadrupole mass spectrometry (SBSE-LD/LVI-GC–qMS) was evaluated for the simultaneous determination of higher alcohol acetates (HAA), isoamyl esters (IsoE) and ethyl esters (EE) of fatty acids. The method performance was assessed and compared with other solventless technique, the solid-phase microextraction (SPME) in headspace mode (HS). For both techniques, influential experimental parameters were optimised to provide sensitive and robust methods. The SBSE-LD/LVI methodology was previously optimised in terms of extraction time, influence of ethanol in the matrix, liquid desorption (LD) conditions and instrumental settings. Higher extraction efficiency was obtained using 60 min of extraction time, 10% ethanol content, n-pentane as desorption solvent, 15 min for the back-extraction period, 10 mL min−1 for the solvent vent flow rate and 10 °C for the inlet temperature. For HS-SPME, the fibre coated with 50/30 μm divinylbenzene/carboxen/polydimethylsiloxane (DVB/CAR/PDMS) afforded highest extraction efficiency, providing the best sensitivity for the target volatiles, particularly when the samples were extracted at 25 °C for 60 min under continuous stirring in the presence of sodium chloride (10% (w/v)). Both methodologies showed good linearity over the concentration range tested, with correlation coefficients higher than 0.984 for HS-SPME and 0.982 for SBES-LD approach, for all analytes. A good reproducibility was attained and low detection limits were achieved using both SBSE-LD (0.03–28.96 μg L−1) and HS-SPME (0.02–20.29 μg L−1) methodologies. The quantification limits for SBSE-LD approach ranging from 0.11 to 96.56 μg L−and from 0.06 to 67.63 μg L−1 for HS-SPME. Using the HS-SPME approach an average recovery of about 70% was obtained whilst by using SBSE-LD obtained average recovery were close to 80%. The analytical and procedural advantages and disadvantages of these two methods have been compared. Both analytical methods were used to determine the HAA, IsoE and EE fatty acids content in “Terras Madeirenses” table wines. A total of 16 esters were identified and quantified from the wine extracts by HS-SPME whereas by SBSE-LD technique were found 25 esters which include 2 higher alcohol acetates, 4 isoamyl esters and 19 ethyl esters of fatty acids. Generally SBSE-LD provided higher sensitivity with decreased analysis time.
Resumo:
É na primeira infância que as crianças aprendem a rotular as emoções, mas só muito mais tarde aprendem a distinguir as manifestações emocionais comportamentais. Se por um lado, umas ainda não conseguem controlar os seus impulsos quando estão a tentar resolver os conflitos entre pares, outras dependem exclusivamente do adulto para tudo o que fazem, há outras, que são tímidas por natureza e não interagem com os colegas (Katz & McClellan, 2001). O estudo foi operacionalizado numa instituição particular na Ilha da Madeira, foi realizada uma amostragem por conveniência, constituída por 27 crianças do jardim-deinfância, com idades compreendidas entre os 3 e os 5 anos. A recolha de dados foi feita através de um questionário de dados sociodemográficos, entrevista semiestruturada e de um teste de avaliação psicológica (TEC - Test of Emotion Comprehension). Os resultados indicam que as crianças apresentam dificuldades em identificar situações de conflito e no que concerne à capacidade de compreensão das emoções, a maioria das crianças que participaram no estudo apresentaram resultados positivos na compreensão emocional, nomeadamente no reconhecimento das emoções e na compreensão das causas externas das emoções.
Resumo:
MELO, D. M. A. et al. Synthesis and charactezarion of lanthanum and yttrium doped Fe2O3 pigments. Cerâmica, São Paulo, v. 53, p. 79-82, 2007.
Resumo:
Research with indigenous in urban context are gaining steam in recent years, particularly with the intensification of migration resulting from problems such as lack of land for subsistence. However, in relation to Terena, subjects in this study, the contemporary anthropological research aimed at residents in cities still are not privileged, especially to youth. Thus, the dissertation has as main objective the discussion around some axes, among them indigenous youth Terena ethnicity politics, - indigenous movement - and racism. These themes appeared during fieldwork where privileged six trajectories of young Terena who migrated to Campo Grande (MS) and have different ways to mean the city and experiencing everyday life
Resumo:
Tanto no contexto acadêmico quanto no artístico e mercadológico, é crescente a discussão sobre o espaço de conceituação da dança contemporânea e suas fissuras, que deixam de abarcar esta ou aquela manifestação artística ou mesmo acaba por abarcar aquelas manifestações que não se encaixam em outros espaços de conceituação. No presente trabalho objetivamos a investigar, a Dança na Contemporaneidade, para além do que se entende por dança contemporânea, em sua capacidade de atravessar os espaços de conceituação já estabelecidos, para implicar em uma pluralidade de fazeres. Objetivamos também pensar a potência que a Dança imprime no corpo do artista criador, pensando também como este se comporta no espaço de entre linguagens . A dissertação que aqui se apresenta encontrou enquanto estratégia metodológica o recurso da metáfora, partindo das ideias de travessia, cartografia e cidades invisíveis para a construção do pensamento sobre o corpo do artista e suas relações com as diferentes linguagens artísticas, tomando por base uma retomada das experiências estéticas e artísticas de sua proponente. Dialogando experiências práticas e referenciais teóricos, inicialmente tratamos da dança contemporânea em seus problemas de classificação que apontam para a necessidade de um pensamento contemporâneo em dança, que pense as manifestações artísticas em seus pontos convergentes, e não nos divergentes que as situam sob diversas nomenclaturas. No capítulo seguinte discutimos a possibilidade de contaminação entre as linguagens artísticas a partir do próprio corpo-artista. Discorremos também sobre a dança enquanto agenciamento e resposta aos impulsos resultantes da relação com o espaço e outros corpos, pensando como o corpo do vivente se organiza nesta relação de compartilhamento de experiências. Mostrando uma potência do corpo artista criador que se dedica à transvaloração das fronteiras entre as linguagens para a organização do seu fazer. Por fim, apontamos para a diversidade na metodologia de processos de criação que variam de acordo com as possibilidades técnicas e necessidades estéticas de cada artista criador
Resumo:
Nickel-based catalysts supported on alumina have been widely used in various reactions to obtain synthesis gas or hydrogen. Usually, higher conversion levels are obtained by these catalysts, however, the deactivation by coke formation and sintering of metal particles are still problems to be solved. Several approaches have been employed in order to minimize these problems, among which stands out in recent years the use of additives such as oxides of alkali metals and rare earths. Similarly, the use of methodologies for the synthesis faster, easier, applicable on an industrial scale and to allow control of the microstructural characteristics of these catalysts, can together provide the solution to this problem. In this work, oxides with spinel type structure AB2O4, where A represents divalent cation and B represents trivalent cations are an important class of ceramic materials investigated worldwide in different fields of applications. The nickel cobaltite (NiCo2O4) was oxides of spinel type which has attracted considerable interest due to its applicability in several areas, such as chemical sensors, flat panel displays, optical limiters, electrode materials, pigments, electrocatalysis, electronic ceramics, among others. The catalyst precursor NiCo2O4 was prepared by a new chemical synthesis route using gelatine as directing agent. The polymer resin obtained was calcined at 350°C. The samples were calcined at different temperatures (550, 750 and 950°C) and characterized by X ray diffraction, measurements of specific surface area, temperature programmed reduction and scanning electron microscopy. The materials heat treated at 550 and 750°C were tested in the partial oxidation of methane. The set of techniques revealed, for solid preparations, the presence of the phase of spinel-type structure with the NiCo2O4 NixCo1-xO solid solution. This solid solution was identified by Rietveld refinement at all temperatures of heat treatment. The catalyst precursors calcined at 550 and 750°C showed conversion levels around 25 and 75%, respectively. The reason H2/CO was around 2 to the precursor treated at 750°C, proposed reason for the reaction of partial oxidation of methane, one can conclude that this material can be shown to produce synthesis gas suitable for use in the synthesis Fischer-Tropsch process
Resumo:
Given the environmental concern over global warming that occurs mainly by emission of CO2 from the combustion of petroleum, coal and natural gas research focused on alternative and clean energy generation has been intensified. Among these, the highlight the solid oxide fuel cell intermediate temperature (IT-SOFC). For application as electrolyte of the devices doped based CeO2 with rare earth ions (TR+ 3) have been quite promising because they have good ionic conductivity and operate at relatively low temperatures (500-800 ° C). In this work, studied the Ce1-xEuxO2-δ (x = 0,1, 0,2 and 0,3), solid solutions synthesized by the polymeric precursor method to be used as solid electrolyte. It was also studied the processing steps of these powders (milling, compaction and two step sintering) in order to obtain dense sintered pellets with reduced grain size and homogeneous microstructure. For this, the powders were characterized by thermal analysis, X-ray diffraction, particle size distribution and scanning electrons microscopy, since the sintered samples were characterized by dilatometry, scanning electrons microscopy, density and grain size measurements. By x-ray diffraction, it was verified the formation of the solid solution for all compositions. Crystallites in the nanometric scale were found for both sintering routes but the two step sintering presented significant reduction in the average grain size
Resumo:
The mixed metal oxides constitute an important class of catalytic materials widely investigated in different fields of applications. Studies of rare earth nickelates have been carried by several researchers in order to investigate the structural stability afforded by oxide formed and the existence of catalytic properties at room temperature. So, this study aims synthesize the nanosized catalyst of nickelate of lanthanum doped with strontium (La(1-x)SrxNiO4-d; x = 0,2 and 0,3), through the Pechini method and your characterization for subsequent application in the desulfurization of thiophene reaction. The precursor solutions were calcined at 300ºC/2h for pyrolysis of polyester and later calcinations occurred at temperatures of 500 - 1000°C. The resulting powders were characterized by thermogravimetric analysis (TG / DTG), surface area for adsorption of N2 by BET method, X-ray diffraction (XRD), scanning electron microscopy (HR_SEM) and spectrometry dispersive energy (EDS). The results of XRD had show that the perovskites obtained consist of two phases (LSN and NiO) and from 700ºC have crystalline structure. The results of SEM evidenced the obtainment of nanometric powders. The results of BET show that the powders have surface area within the range used in catalysis (5-50m2/g). The characterization of active sites was performed by reaction of desulfurization of thiophene at room temperature and 200ºC, the relation F/W equal to 0,7 mol h-1mcat -1. The products of the reaction were separated by gas chromatography and identified by the selective detection PFPD sulfur. All samples had presented conversion above 95%
Resumo:
Fuel cells are electrochemical devices that convert chemical energy into electricity. Due to the development of new materials, fuel cells are emerging as generating clean energy generator. Among the types of fuel cells, categorized according to the electrode type, the solid oxide fuel cells (SOFC) stand out due to be the only device entirely made of solid particles. Beyond that, their operation temperature is relatively high (between 500 and 1000 °C), allowing them to operate with high efficiency. Another aspect that promotes the use of SOFC over other cells is their ability to operate with different fuels. The CeO2 based materials doped with rare earth (TR+3) may be used as alternatives to traditional NiO-YSZ anodes as they have higher ionic conductivity and smaller ohmic losses compared to YSZ, and can operate at lower temperatures (500-800°C). In the composition of the anode, the concentration of NiO, acting as a catalyst in YSZ provides high electrical conductivity and high electrochemical activity of reactions, providing internal reform in the cell. In this work compounds of NiO - Ce1-xEuxO2-δ (x = 0.1, 0.2 and 0.3) were synthesized from polymeric precursor, Pechini, method of combustion and also by microwave-assisted hydrothermal method. The materials were characterized by the techniques of TG, TPR, XRD and FEG-SEM. The refinement of data obtained by X-ray diffraction showed that all powders of NiO - Cex-1EuxO2-δ crystallized in a cubic phase with fluorite structure, and also the presence of Ni. Through the characterizations can be proved that all routes of preparation used were effective for producing ceramics with characteristics suitable for application as SOFC anodes, but the microwave-assisted hydrothermal method showed a significant reduction in the average grain size and improved control of the compositions of the phases
Resumo:
Alternative and clean energy generation research has been intensified in last decades. Among the alternatives, fuel cells are one of the most important. There are different types of fuel cells, among which stands out intermediate temperature solid oxide fuel cell (IT-SOFC) matter of the present work. For application as cathode on this type of devices, the ceramic Ba0.5Sr0.5C0.8Fe0.2O3-δ doped with rare earth ions (Nd, Sm) have been quite promising because they show good ionic conductivity and operate at relatively low temperatures (500 - 800°C). In this work, Ba0.5Sr0.5Co0.8Fe0.2O3-δ, (BaSr)0.5Sm0.5Co0.8Fe0.2O3-δ and (BaSr)0.5Nd0.5C0.8Fe0.2O3-δ were obtained by modified Pechini method, making use of gelatin as polymerizing agent. The powders were characterized by X-Ray Diffraction (XRD), Temperature Programmed Reduction (TPR) and Scanning Electron Microscopy (SEM). The perovskite phase was observed in all X-ray patterns for the materials Ba0.5Sr0.5C0.8Fe0.2O3-δ doped with rare earth ions (Nd, Sm). The SEM images showed that the materials have a characteristics porous, with very uniform pore distribution, which are favorable for application as cathodes. Subsequently, screen-printed assymmetrical cells were studied by impedance spectroscopy, to assess the kinetics of the cathode for the reduction reaction of oxygen. The best resistance to the specific area was found for the cathode BSSCF sintered at 1050 °C for 4 hours with around 0.15 Ω.cm2 at 750 °C as well as cathodes BSNCF and BSCF obtained resistances specific area of 0.2 and 0.73 Ω.cm2, respectively, for the same conditions. The polarization curves showed similar behavior to the best cathodes BSSCF and BSNCF, such combination of properties indicates that the film potentially depict good performance as IT-SOFC cathodes
Resumo:
Recent studies are investigating a new class of inorganic materials which arise as a promising option for high performance applications in the field of photoluminescence. Highlight for rare earth (TR +3 ) doped, which have a high luminous efficiency, long decay time and being able to emit radiation in the visible range, specific to each element. In this study, we synthesized ZrO2: Tb +3 , Eu +3 , Tm +3 nanoparticles complex polymerization method (CPM). We investigated the influences caused by the heat treatment temperature and the content of dopants in zirconia photoluminescent behavior. The particles were calcined at temperature of 400, 500 and 600 ° C for two hours and ranged in concentration of dopants 1, 2, 4 and 8 mol% TR +3 . The samples were characterized by thermal analysis, X-ray diffraction, photoluminescence of measurements and uv-visible of spectroscopies. The results of X-ray diffraction confirmed the formation of the tetragonal and cubic phases in accordance with the content of dopants. The photoluminescence spectra show emission in the region corresponding simultaneous to blue (450 nm), green (550 nm) and red (615 nm). According to the results, ZrO2 particles co-doped with rare earth ions is a promising material white emission with a potential application in the field of photoluminescence
Resumo:
Fuel cells are considered one of the most promising ways of converting electrical energy due to its high yield and by using hydrogen (as fuel) which is considered one of the most important source of clean energy for the future. Rare earths doped ceria has been widely investigated as an alternative material for the electrolyte of solid oxide fuel cells (SOFCs) due to its high ionic conductivity at low operating temperatures compared with the traditional electrolytes based on stabilized zirconia. This work investigates the effect of gallium oxide (Gallia) as a sintering aid in Eu doped ceria ceramic electrolytes since this effect has already been investigated for Gd, Sm and Y doped ceria electrolytes. The desired goal with the use of a sintering aid is to reduce the sintering temperature aiming to produce dense ceramics. In this study we investigated the effects on densification, microstructure and ionic conduction caused by different molar fraction of the dopants europium (10, 15 and 20%) and gallium oxide (0.3, 0.6 and 0.9%) in samples sintered at 1300, 1350 and 1450 0 C. Samaria (10 and 20%) doped ceria samples sintered between 1350 and 1450 °C were used as reference. Samples were synthesized using the cation complexation method. The ceramics powders were characterized by XRF, XRD and SEM, while the sintered samples were investigated by its relative density, SEM and impedance spectroscopy. It was showed that gallia contents up to 0.6% act as excellent sintering aids in Eu doped ceria. Above this aid content, gallia addition does not promote significant increase in density of the ceramics. In Ga free samples the larger densification were accomplished with Eu 15% molar, effect expressed in the microstructure with higher grain growth although reduced and surrounded by many open pores. Relative densities greater than 95 % were obtained by sintering between 1300 and 1350 °C against the usual range 1500 - 1600 0 C. Samples containing 10% of Sm and 0.9% of Ga reached 96% of theoretical density by sintering at 1350 0 C for 3h, a gain compared to 97% achieved with 20% of Sm and 1% of Ga co-doped cerias sintered at 1450 0 C for 24 h as described in the literature. It is found that the addition of gallia in the Eu doped ceria has a positive effect on the grain conductivity and a negative one in the grain boundary conductivity resulting in a small decrease in the total conductivity which will not compromise its application as sintering aids in ceria based electrolytes. Typical total conductivity values at 600 and 700 °C, around 10 and 30 mS.cm -1 respectively were reached in this study. Samples with 15% of Eu and 0.9 % of Ga sintered at 1300 and 1350 °C showed relative densities greater than 96% and total conductivity (measured at 700 °C) between 20 and 33 mS.cm -1 . The simultaneous sintering of the electrolyte with the anode is one of the goals of research in materials for SOFCs. The results obtained in this study suggest that dense Eu and Ga co-doped ceria electrolytes with good ionic conductivity can be sintered simultaneously with the anode at temperatures below 1350 °C, the usual temperature for firing porous anode materials
Resumo:
This work presents the results of a survey in oil-producing region of the Macau City, northern coast of Rio Grande do Norte. All work was performed under the Project for Monitoring Environmental Change and the Influence of Hydrodynamic forcing on Morphology Beach Grass Fields, Serra Potiguar in Macau, with the support of the Laboratory of Geoprocessing, linked to PRH22 - Training Program in Geology Geophysics and Information Technology Oil and Gas - Department of Geology/CCET/UFRN and the Post-Graduation in Science and Engineering Oil/PPGCEP/UFRN. Within the economic-ecological context, this paper assesses the importance of mangrove ecosystem in the region of Macau and its surroundings as well as in the following investigative exploration of potential areas for projects involving reforestation and / or Environmental Restoration. At first it was confirmed the ecological potential of mangrove forests, with primary functions: (i) protection and stabilization of the shoreline, (ii) nursery of marine life, and (iii) source of organic matter to aquatic ecosystems, (iv) refuge of species, among others. In the second phase, using Landsat imagery and techniques of Digital Image Processing (DIP), I came across about 18,000 acres of land that can be worked on environmental projects, being inserted in the rules signed the Kyoto Protocol to the market carbon. The results also revealed a total area of 14,723.75 hectares of activity of shrimp production and salting that can be harnessed for the social, economic and environmental potential of the region, considering that over 60% of this area, ie, 8,800 acres, may be used in the planting of the genus Avicennia considered by the literature that the species best sequesters atmospheric carbon, reaching a mean value of 59.79 tons / ha of mangrove
Resumo:
This research proposed to question the development of what was defined as historical practices (commercial, social and political institutions), of the economic activity of the real estate brokerage in the Rio Grande do Norte from the progressive institutionalization of economic agents - individuals (realtors) and legal (real estate) - based on two main approaches: a) the development of economic activity as an integral segment of a fraction of capital (POULANTZAs, 1985; LESSA, 1981). This work set out from a socio-historical approach of the historical practices development the of real estate brokerage in Brazil started in the Southeast, especially in the cities of Rio de Janeiro and São Paulo as a result of the "expansion of capitalist relations by the housing sector" (RIBEIRO , 1996). especially the real estate capital ; b) the historical development of relations between labor and capital within the activity, in other words, the development of the relationship between realtors and Real Estate in relation to "group of interests" and their "collective actions" (OFFE, 1984). These historical practices are defined in this research as: 1) mercantile practices, times when there was no distinction between the activity of real estate brokerage and other forms of mercantile capital; 2) social practices, which began in the 1930s, when agents of real estate are to be distinguished from each other within the activity through Taylorist division of labor between workers realtors and developers of real estate; 3) political and institutional practices, initiated in 1962, characterized by State action, in the individualization and distinction of the agents of real estate brokerage as socioprofessional category regulated throughout Brazil by Law 4.116/62 and 6.530/78. The results achieved by the present study showed that in Rio Grande do Norte, due to the specifics as to the peripheral processes of urbanization of the constitution of the land market, as well as the process of conservative modernization of the oligarchic State from the 1960s (CLEMENTINE, 1995; FERREIRA, 1996, 2010, TRINDADE, 2004), the State was led to the development of a late manifestation of the historical practices of real estate brokerage. In other words, it was a process in which historical practices, in particular social practices, not fully developed, mitigating, thus the perception of realtors from his position in the process of exploitation of labor by the Real Estate. And, as a result, of their collective interests front of them.
Resumo:
This dissertation aims to understand the importance of the National School Feeding as a strategy for ensuring the promotion of food and nutrition security in the municipality of Macaíba / RN, taking into account the implementation of the Law School Feeding, 11,947, 2009. The program was extended to all public basic education, youth and adults, in addition to ensuring that 30% of transfers from FNDE, were intended for the purchase of products from family farms. The survey was conducted with 160 students from public schools and farmers nesting Quilombo dos Palmares II, who produce on their land vegetables, fruits and cereals for their own consumption, for sale in local markets, in addition to providing for PNAE. The reciprocity between neighbors, such as mutual aid and sharing of common goods was noticeable in this group of farmers, since it was necessary to meet weekly deliveries of products to schools. As students, we applied a test of acceptability in two schools located in rural and in urban areas, to learn the opinion of ourselves in relation to school food consumed. It was concluded that to be most effective program in the region, there must be a better match in school menus, so that it can be attractive to students and to ensure greater use of fresh food, the main ingredient of same, practice of nutrition education in schools, to teach students the importance of food to health. In relation to local management, noted the need for adjustments bureaucratic as hiring staff for the departments, in order to be more agile in releasing payments to farmers, in addition to hiring assistants general services for schools, one Since the cooks exert dual role, the cooking while being responsible for cleaning the entire school environment. Government investments in the rural sector would be extremely valuable for farmers, since they need financial resources to purchase inputs, irrigation projects for gardens, availability of land for planting, transportation to facilitate the delivery of its products to schools and technical assistance more frequently