Validation of the CFD code NEPTUNE for a full scale simulator for decay heat removal systems with in-pool heat exchangers

In the present work, a multi physics simulation of an innovative safety system for light water nuclear reactor is performed, with the aim to increase the reliability of its main decay heat removal system. The system studied, denoted by the acronym PERSEO (in Pool Energy Removal System for Emergency Operation) is able to remove the decay power from the primary side of the light water nuclear reactor through a heat suppression pool. The experimental facility, located at SIET laboratories (PIACENZA), is an evolution of the Thermal Valve concept where the triggering valve is installed liquid side, on a line connecting two pools at the bottom. During the normal operation, the valve is closed, while in emergency conditions it opens, the heat exchanger is flooded with consequent heat transfer from the primary side to the pool side. In order to verify the correct system behavior during long term accidental transient, two main experimental PERSEO tests are analyzed. For this purpose, a coupling between the mono dimensional system code CATHARE, which reproduces the system scale behavior, with a three-dimensional CFD code NEPTUNE CFD, allowing a full investigation of the pools and the injector, is implemented. The coupling between the two codes is realized through the boundary conditions. In a first analysis, the facility is simulated by the system code CATHARE V2.5 to validate the results with the experimental data. The comparison of the numerical results obtained shows a different void distribution during the boiling conditions inside the heat suppression pool for the two cases of single nodalization and three volume nodalization scheme of the pool. Finaly, to improve the investigation capability of the void distribution inside the pool and the temperature stratification phenomena below the injector, a two and three dimensional CFD models with a simplified geometry of the system are adopted.

Measurement of the oscillation frequency of B s mesons in the hadronic decay mode B s pi D s (phi pi) X with the D0 detector at the Fermilab Tevatron collider

The standard model (SM) of particle physics is a theory, describing three out of four fundamental forces. In this model the Cabibbo-Kobayashi-Maskawa (CKM) matrix describes the transformation between the mass and weak eigenstates of quarks. The matrix properties can be visualized as triangles in the complex plane. A precise measurement of all triangle parameters can be used to verify the validity of the SM. The least precisely measured parameter of the triangle is related to the CKM element |Vtd|, accessible through the mixing frequency (oscillation) of neutral B mesons, where mixing is the transition of a neutral meson into its anti-particle and vice versa. It is possible to calculate the CKM element |Vtd| and a related element |Vts| by measuring the mass differences Dmd (Dms ) between neutral Bd and bar{Bd} (Bs and bar{Bs}) meson mass eigenstates. This measurement is accomplished by tagging the initial and final state of decaying B mesons and determining their lifetime. Currently the Fermilab Tevatron Collider (providing pbar{p} collisions at sqrt{s}=1.96 TeV) is the only place, where Bs oscillations can be studied. The first selection of the "golden", fully hadronic decay mode Bs->Ds pi(phi pi)X at DØ is presented in this thesis. All data, taken between April 2002 and August 2007 with the DØ detector, corresponding to an integrated luminosity of int{L}dt=2.8/fb is used. The oscillation frequency Dms and the ratio |Vtd|/|Vts| are determined as Dms = (16.6 +0.5-0.4(stat) +0.4-0.3(sys)) 1/ps, |Vtd|/|Vts| = 0.213 +0.004-0.003(exp)pm 0.008(theor). These results are consistent with the standard model expectations and no evidence for new physics is observable.

The electron antineutrino angular correlation coefficient a in free neutron decay: Testing the standard model with the aSPECT-spectrometer

The beta-decay of free neutrons is a strongly over-determined process in the Standard Model (SM) of Particle Physics and is described by a multitude of observables. Some of those observables are sensitive to physics beyond the SM. For example, the correlation coefficients of the involved particles belong to them. The spectrometer aSPECT was designed to measure precisely the shape of the proton energy spectrum and to extract from it the electron anti-neutrino angular correlation coefficient "a". A first test period (2005/ 2006) showed the “proof-of-principles”. The limiting influence of uncontrollable background conditions in the spectrometer made it impossible to extract a reliable value for the coefficient "a" (publication: Baessler et al., 2008, Europhys. Journ. A, 38, p.17-26). A second measurement cycle (2007/ 2008) aimed to under-run the relative accuracy of previous experiments (Stratowa et al. (1978), Byrne et al. (2002)) da/a =5%. I performed the analysis of the data taken there which is the emphasis of this doctoral thesis. A central point are background studies. The systematic impact of background on a was reduced to da/a(syst.)=0.61 %. The statistical accuracy of the analyzed measurements is da/a(stat.)=1.4 %. Besides, saturation effects of the detector electronics were investigated which were initially observed. These turned out not to be correctable on a sufficient level. An applicable idea how to avoid the saturation effects will be discussed in the last chapter.

Aircraft-based in-situ aerosol mass spectrometry: Chemical characterization and source identification of submicron particulate matter in the free and upper troposphere and lower stratosphere

The composition of the atmosphere is frequently perturbed by the emission of gaseous and particulate matter from natural as well as anthropogenic sources. While the impact of trace gases on the radiative forcing of the climate is relatively well understood the role of aerosol is far more uncertain. Therefore, the study of the vertical distribution of particulate matter in the atmosphere and its chemical composition contribute valuable information to bridge this gap of knowledge. The chemical composition of aerosol reveals information on properties such as radiative behavior and hygroscopicity and therefore cloud condensation or ice nucleus potential. rnThis thesis focuses on aerosol pollution plumes observed in 2008 during the POLARCAT (Polar Study using Aircraft, Remote Sensing, Surface Measurements and Models, of Climate, Chemistry, Aerosols, and Transport) campaign over Greenland in June/July and CONCERT (Contrail and Cirrus Experiment) campaign over Central and Western Europe in October/November. Measurements were performed with an Aerodyne compact time-of-flight aerosol mass spectrometer (AMS) capable of online size-resolved chemical characterization of non-refractory submicron particles. In addition, the origins of pollution plumes were determined by means of modeling tools. The characterized pollution episodes originated from a large variety of sources and were encountered at distinct altitudes. They included pure natural emissions from two volcanic eruptions in 2008. By the time of detection over Western Europe between 10 and 12 km altitude the plume was about 3 months old and composed to 71 % of particulate sulfate and 21 % of carbonaceous compounds. Also, biomass burning (BB) plumes were observed over Greenland between 4 and 7 km altitude (free troposphere) originating from Canada and East Siberia. The long-range transport took roughly one and two weeks, respectively. The aerosol was composed of 78 % organic matter and 22 % particulate sulfate. Some Canadian and all Siberian BB plumes were mixed with anthropogenic emissions from fossil fuel combustion (FF) in North America and East Asia. It was found that the contribution of particulate sulfate increased with growing influences from anthropogenic activity and Asia reaching up to 37 % after more than two weeks of transport time. The most exclusively anthropogenic emission source probed in the upper troposphere was engine exhaust from commercial aircraft liners over Germany. However, in-situ characterization of this aerosol type during aircraft chasing was not possible. All long-range transport aerosol was found to have an O:C ratio close to or greater than 1 implying that low-volatility oxygenated organic aerosol was present in each case despite the variety of origins and the large range in age from 3 to 100 days. This leads to the conclusion that organic particulate matter reaches a final and uniform state of oxygenation after at least 3 days in the free troposphere. rnExcept for aircraft exhaust all emission sources mentioned above are surface-bound and thus rely on different types of vertical transport mechanisms, such as direct high altitude injection in the case of a volcanic eruption, or severe BB, or uplift by convection, to reach higher altitudes where particles can travel long distances before removal mainly caused by cloud scavenging. A lifetime for North American mixed BB and FF aerosol of 7 to 11 days was derived. This in consequence means that emission from surface point sources, e.g. volcanoes, or regions, e.g. East Asia, do not only have a relevant impact on the immediate surroundings but rather on a hemispheric scale including such climate sensitive zones as the tropopause or the Arctic.

Experimental assessment of environmental decay effects in masonry via non destructive diagnostic techniques and mechanical tests

Environmental decay in porous masonry materials, such as brick and mortar, is a widespread problem concerning both new and historic masonry structures. The decay mechanisms are quite complex dependng upon several interconnected parameters and from the interaction with the specific micro-climate. Materials undergo aesthetical and substantial changes in character but while many studies have been carried out, the mechanical aspect has been largely understudied while it bears true importance from the structural viewpoint. A quantitative assessment of the masonry material degradation and how it affects the load-bearing capacity of masonry structures appears missing. The research work carried out, limiting the attention to brick masonry addresses this issue through an experimental laboratory approach via different integrated testing procedures, both non-destructive and mechanical, together with monitoring methods. Attention was focused on transport of moisture and salts and on the damaging effects caused by the crystallization of two different salts, sodium chloride and sodium sulphate. Many series of masonry specimens, very different in size and purposes were used to track the damage process since its beginning and to monitor its evolution over a number of years Athe same time suitable testing techniques, non-destructive, mini-invasive, analytical, of monitoring, were validated for these purposes. The specimens were exposed to different aggressive agents (in terms of type of salt, of brine concentration, of artificial vs. open-air natural ageing, …), tested by different means (qualitative vs. quantitative, non destructive vs. mechanical testing, punctual vs. wide areas, …), and had different size (1-, 2-, 3-header thick walls, full-scale walls vs. small size specimens, brick columns and triplets vs. small walls, masonry specimens vs. single units of brick and mortar prisms, …). Different advanced testing methods and novel monitoring techniques were applied in an integrated holistic approach, for quantitative assessment of masonry health state.

Measurement of the proton recoil spectrum in neutron beta decay with the spectrometer aSPECT : study of systematic effects

Precision measurements of observables in neutron beta decay address important open questions of particle physics and cosmology. In this thesis, a measurement of the proton recoil spectrum with the spectrometer aSPECT is described. From this spectrum the antineutrino-electron angular correlation coefficient a can be derived. In our first beam time at the FRM II in Munich, background instabilities prevented us from presenting a new value for a. In the latest beam time at the ILL in Grenoble, the background has been reduced sufficiently. As a result of the data analysis, we identified and fixed a problem in the detector electronics which caused a significant systematic error. The aim of the latest beam time was a new value for a with an error well below the present literature value of 4%. A statistical accuracy of about 1.4% was reached, but we could only set upper limits on the correction of the problem in the detector electronics, too high to determine a meaningful result. This thesis focused on the investigation of different systematic effects. With the knowledge of the systematics gained in this thesis, we are able to improve aSPECT to perform a 1% measurement of a in a further beam time.

Measurement of the pair production of b-jets in proton-proton collisions at root out s = 7 TeV with the ATLAS detector

In hadronischen Kollisionen entstehen bei einem Großteil der Ereignisse mit einem hohen Impulsübertrag Paare aus hochenergetischen Jets. Deren Produktion und Eigenschaften können mit hoher Genauigkeit durch die Störungstheorie in der Quantenchromodynamik (QCD) vorhergesagt werden. Die Produktion von \textit{bottom}-Quarks in solchen Kollisionen kann als Maßstab genutzt werden, um die Vorhersagen der QCD zu testen, da diese Quarks die Dynamik des Produktionsprozesses bei Skalen wieder spiegelt, in der eine Störungsrechnung ohne Einschränkungen möglich ist. Auf Grund der hohen Masse von Teilchen, die ein \textit{bottom}-Quark enthalten, erhält der gemessene, hadronische Zustand den größten Teil der Information von dem Produktionsprozess der Quarks. Weil sie eine große Produktionsrate besitzen, spielen sie und ihre Zerfallsprodukte eine wichtige Rolle als Untergrund in vielen Analysen, insbesondere in Suchen nach neuer Physik. In ihrer herausragenden Stellung in der dritten Quark-Generation könnten sich vermehrt Zeichen im Vergleich zu den leichteren Quarks für neue Phänomene zeigen. Daher ist die Untersuchung des Verhältnisses zwischen der Produktion von Jets, die solche \textit{bottom}-Quarks enthalten, auch bekannt als $b$-Jets, und aller nachgewiesener Jets ein wichtiger Indikator für neue massive Objekte. In dieser Arbeit werden die Produktionsrate und die Korrelationen von Paaren aus $b$-Jets bestimmt und nach ersten Hinweisen eines neuen massiven Teilchens, das bisher nicht im Standard-Modell enthalten ist, in dem invarianten Massenspektrum der $b$-Jets gesucht. Am Large Hadron Collider (LHC) kollidieren zwei Protonenstrahlen bei einer Schwerpunktsenergie von $\sqrt s = 7$ TeV, und es werden viele solcher Paare aus $b$-Jets produziert. Diese Analyse benutzt die aufgezeichneten Kollisionen des ATLAS-Detektors. Die integrierte Luminosität der verwendbaren Daten beläuft sich auf 34~pb$^{-1}$. $b$-Jets werden mit Hilfe ihrer langen Lebensdauer und den rekonstruierten, geladenen Zerfallsprodukten identifiziert. Für diese Analyse müssen insbesondere die Unterschiede im Verhalten von Jets, die aus leichten Objekten wie Gluonen und leichten Quarks hervorgehen, zu diesen $b$-Jets beachtet werden. Die Energieskala dieser $b$-Jets wird untersucht und die zusätzlichen Unsicherheit in der Energiemessung der Jets bestimmt. Effekte bei der Jet-Rekonstruktion im Detektor, die einzigartig für $b$-Jets sind, werden studiert, um letztlich diese Messung unabhängig vom Detektor und auf Niveau der Hadronen auswerten zu können. Hiernach wird die Messung zu Vorhersagen auf nächst-zu-führender Ordnung verglichen. Dabei stellt sich heraus, dass die Vorhersagen in Übereinstimmung zu den aufgenommenen Daten sind. Daraus lässt sich schließen, dass der zugrunde liegende Produktionsmechanismus auch in diesem neu erschlossenen Energiebereich am LHC gültig ist. Jedoch werden auch erste Hinweise auf Mängel in der Beschreibung der Eigenschaften dieser Ereignisse gefunden. Weiterhin können keine Anhaltspunkte für eine neue Resonanz, die in Paare aus $b$-Jets zerfällt, in dem invarianten Massenspektrum bis etwa 1.7~TeV gefunden werden. Für das Auftreten einer solchen Resonanz mit einer Gauß-förmigen Massenverteilung werden modell-unabhängige Grenzen berechnet.

The role of indigenous people in national development processes: Participation and marginalisation of indigenous Bedouin in South Sinai tourism development

The Bedouin of South Sinai have been significantly affected by the politics of external powers for a long time. However, never had the interest of external powers in Sinai been so strong as since the Israeli-Egyptian wars in the second half of the 20th century when Bedouin interests started to collide with Egypt’s plans for a development of luxury tourism in South Sinai. rnrnThe tourism boom that has started in the 1980s has brought economic and infrastructure development to the Bedouin and tourism has become the most important source of income for the Bedouin. However, while the absolute increase of tourists to Sinai has trickled down to the Bedouin to some extent, the participation of Bedouin in the overall tourism development is under-proportionate. Moreover, the Bedouin have become increasingly dependent on monetary income and consequently from tourism as the only significant source of income while at the same time they have lost much of their land as well as their self-determination.rnrnIn this context, the Bedouin livelihoods have become very vulnerable due to repeated depressions in the tourism industry as well as marginalization. Major marginalization processes the Bedouin are facing are the loss of land, barriers to market entry, especially increasingly strict rules and regulations in the tourism industry, as well as discrimination by the authorities. Social differentiation and Bedouin preferences are identified as further factors in Bedouin marginalization.rnrnThe strategies Bedouin have developed in response to all these problems are coping strategies, which try to deal with the present problem at the individual level. Basically no strategies have been developed at the collective level that would aim to actively shape the Bedouin’s present and future. Collective action has been hampered by a variety of factors, such as the speed of the developments, the distribution of power or the decay of tribal structures.rnWhile some Bedouin might be able to continue their tourism activities, a large number of informal jobs will not be feasible anymore. The majority of the previously mostly self-employed Bedouin will probably be forced to work as day-laborers who will have lost much of their pride, dignity, sovereignty and freedom. Moreover, with a return to subsistence being impossible for the majority of the Bedouin, it is likely that an increasing number of marginalized Bedouin will turn to illegal income generating activities such as smuggling or drug cultivation. This in turn will lead to further repression and discrimination and could escalate in a serious violent conflict between the Bedouin and the government.rnrnDevelopment plans and projects should address the general lack of civil rights, local participation and protection of minorities in Egypt and promote Bedouin community development and the consideration of Bedouin interests in tourism development.rnrnWether the political upheavals and the resignation of president Mubarak at the beginning of 2011 will have a positive effect on the situation of the Bedouin remains to be seen.rn

Analisi delle prestazioni di un codice di calcolo open-source per l'elaborazione dati GNSS in modalità cinematica finalizzata al monitoraggio di strutture e applicazione di filtri sequenziali

Il presente lavoro di tesi si pone come obbiettivo l’elaborazione di dati GNSS in modalità cinematica post-processing per il monitoraggio strutturale e, in una seconda fase, lo studio delle precisioni raggiungibili delle soluzioni ottenute utilizzando algoritmi di post-elaborazione del dato. L’oggetto di studio è la torre Garisenda, situata in piazza Ravegnana, accanto alla torre Asinelli, nel centro storico di Bologna, da tempo oggetto di studi e monitoraggi per via della sua inclinazione particolarmente critica. Per lo studio è stato utilizzato un data set di quindici giorni, dal 15/12/2013 al 29/12/2013 compresi. Per l’elaborazione dei dati è stato utilizzato un software open source realizzato da ricercatori del Politecnico di Milano, goGPS. Quest'ultimo, essendo un codice nuovo, è stato necessario testarlo al fine di poter ottenere dei risultati validi. Nella prima fase della tesi si è quindi affrontato l’aspetto della calibrazione dei parametri che forniscono le soluzioni più precise per le finalità di monitoraggio considerando le possibili scelte offerte dal codice goGPS. In particolare sono stati imposti dei movimenti calibrati e si è osservata la soluzione al variare dei parametri selezionati scegliendo poi quella migliore, ossia il miglior compromesso tra la capacità di individuare i movimenti e il rumore della serie. Nella seconda fase, allo scopo di poter migliorare le precisioni delle soluzioni si sono valutati metodi di correzione delle soluzioni basati sull'uso di filtri sequenziali e sono state condotte analisi sull'incremento di precisione derivante dall'applicazione di tali correzioni.

Source of funding in experimental studies of mobile phone use on health: Update of systematic review

A previous review showed that among 59 studies published in 1995–2005, industry-funded studies were least likely to report effects of controlled exposure to mobile phone radiation on health-related outcomes. We updated literature searches in 2005–2009 and extracted data on funding, conflicts of interest and results. Of 75 additional studies 12% were industry-funded, 44% had public and 19% mixed funding; funding was unclear in 25%. Previous findings were confirmed: industry-sponsored studies were least likely to report results suggesting effects. Interestingly, the proportion of studies indicating effects declined in 1995–2009, regardless of funding source. Source of funding and conflicts of interest are important in this field of research.

Habitat-specific demography and source-sink dynamics in a population of Siberian jays

P>1. There are a number of models describing population structure, many of which have the capacity to incorporate spatial habitat effects. One such model is the source-sink model, that describes a system where some habitats have a natality that is higher than mortality (source) and others have a mortality that exceeds natality (sink). A source can be maintained in the absence of migration, whereas a sink will go extinct. 2. However, the interaction between population dynamics and habitat quality is complex, and concerns have been raised about the validity of published empirical studies addressing source-sink dynamics. In particular, some of these studies fail to provide data on survival, a significant component in disentangling a sink from a low quality source. Moreover, failing to account for a density-dependent increase in mortality, or decrease in fecundity, can result in a territory being falsely assigned as a sink, when in fact, this density-dependent suppression only decreases the population size to a lower level, hence indicating a 'pseudo-sink'. 3. In this study, we investigate a long-term data set for key components of territory-specific demography (mortality and reproduction) and their relationship to habitat characteristics in the territorial, group-living Siberian jay (Perisoreus infaustus). We also assess territory-specific population growth rates (r), to test whether spatial population dynamics are consistent with the ideas of source-sink dynamics. 4. Although average mortality did not differ between sexes, habitat-specific mortality did. Female mortality was higher in older forests, a pattern not observed in males. Male mortality only increased with an increasing amount of open areas. Moreover, reproductive success was higher further away from human settlement, indicating a strong effect of human-associated nest predators. 5. Averaged over all years, 76% of the territories were sources. These territories generally consisted of less open areas, and were located further away from human settlement. 6. The source-sink model provides a tool for modelling demography in distinct habitat patches of different quality, which can aid in identifying key habitats within the landscape, and thus, reduce the risk of implementing unsound management decisions.