Aerodynamic design of high end wall angle turbine stages- part II: Experimental verification

An experimental investigation of a turbine stage featuring very high end wall angles is presented. The initial turbine design did not achieve a satisfactory performance and the difference between the design predictions and the test results was traced to a large separated region on the rear suction-surface. To improve the agreement between computational fluid dynamics (CFD) and experiment, it was found necessary to modify the turbulence modeling employed. The modified CFD code was then used to redesign the vane, and the changes made are described. When tested, the performance of the redesigned vane was found to have much closer agreement with the predictions than the initial vane. Finally, the flowfield and performance of the redesigned stage are compared to a similar turbine, designed to perform the same duty, which lies in an annulus of moderate end wall angles. A reduction in stage efficiency of at least 2.4% was estimated for the very high end wall angle design. © 2014 by ASME.

Comparison of moment-curvature models for fiber-reinforced polymer plate-end debonding studies using global energy balance approach

This paper compares a number of different moment-curvature models for cracked concrete sections that contain both steel and external fiber-reinforced polymer (FRP) reinforcement. The question of whether to use a whole-section analysis or one that considers the FRP separately is discussed. Five existing and three new models are compared with test data for moment-curvature or load deflection behavior, and five models are compared with test results for plate-end debonding using a global energy balance approach (GEBA). A proposal is made for the use of one of the simplified models. The availability of a simplified model opens the way to the production of design aids so that the GEBA can be made available to practicing engineers through design guides and parametric studies. Copyright © 2014, American Concrete Institute.

Is the genus Digramma synonymous to the genus Ligula (Cestoda : Pseudophyllidea)? Evidence from ITS and 5 ' end 28S rDNA sequences

The genus Digramma (Cestoda: Pseudophyllidea) described by Cholodkovsky in 1915 differs from the genus Ligula only by the number of the reproductive organs per proglottis. However, the occurrence of transitional forms in Digramma raises much confusion concerning its generic validity. In the present study, cestodes previously designated as Digramma and Ligula were collected from lakes in the lower and middle reaches of the Yangtze River, and also from Qinghai Lake on Qingzang plateau, China. The entire internal transcribed spacer of the ribosomal DNA (ITS rDNA) and 5' end of 28S rDNA were compared between the Digramma and Ligula specimens. The low level of nucleotide variation between the two genera may imply that cestodes in the genus Digramma are paraphyletic to the Ligula genus, and Digramma is a synonym of Ligula. However, whether previously identified Digramma cestodes represent different species in the genus Ligula requires further investigation.

Fabrication and optical optimization of spot-size converters with strong cladding layers

A silicon-on-insulator (SOI) optical fiber-to-waveguide spot-size converter (SSC) overlaid with specially treated silica is investigated for integrated optical circuits. Unlike the conventional process of simply depositing the hot silica on silicon waveguides, two successive layers of silicon dioxide were grown on etched SSC structures by PECVD (plasma-enhanced chemical vapor deposition). The two layers have 0.8% index contrast and supply stronger cladding for an incident light beam. Additionally, this process is able to reduce the effective refractive index of the input mode to less than 1.47 (extremely close to that of the fiber), substantially weakening the unwanted back reflection. Exploiting this technology, it was demonstrated that the SSC showed a theoretical low mode mismatch loss of 1.23 dB for a TE-like mode and has an experimental coupling efficiency of 66%.

Analog-digital and digital-analog converters using single-electron and MOS transistors

This paper proposes two kinds of novel single-electron analog-digital conversion (ADC) and digital-analog conversion (DAC) circuits that consist of single-electron transistors (SETs) and metal-oxide-semiconductor (MOS) transistors. The SET/MOS hybrid ADC and DAC circuits possess the merits of the SET circuit and the MOS circuit. We obtain the SPICE macro-modeling code of the SET transistor by studying and fitting the characteristics of the SET with SPICE simulation and Monte Carlo simulation methods. The SPICE macro-modeling code is used for the simulation of the SET/MOS hybrid ADC and DAC circuits. We simulate the performances of the SET/MOS hybrid 3-b ADC and 2-b DAC circuits by using the H-SPICE simulator. The simulation results demonstrate that the hybrid circuits can perform analog-digital and digital-analog data conversion well at room temperature. The hybrid ADC and DAC circuits have advantages as-follows: 1) compared with conventional circuits, the architectures of the circuits are simpler; 2) compared with single electron transistor circuits, the circuits have much larger load capability; 3) the power dissipation of the circuits are lower than uW; 4) the data conversion rate of the circuits can exceed 100 MHz; and 5) the resolution of the ADC and DAC circuits can be increased by the pipeline architectures.

Lossless electroabsorption modulator monolithically rntegrated with a semiconductor optical amplifier and dual-wavegulde spot-size converters

Semiconductor optical amplifier and electroabsorption modulator monolithically integrated with dual-waveguide spot-size converters at the input and output ports is demonstrated by means of selective area growth, quantum-well intermixing, and asymmetric twin waveguide technologies. At the wavelength range of 1550 similar to 1600 nm, lossless operation with extinction ratios of 25-dB dc and 11.8-dB radio frequency and more than 10-GHz 3-dB modulation bandwidth is successfully achieved. The output beam divergence angles of the device in the horizontal and vertical directions are as small as 7.3 degrees x 10.6 degrees, respectively, resulting in 3.0-dB coupling loss with cleaved single-mode optical fiber.

Diode-end-pumped passively mode-locked ceramic Nd : YAG Laser with a semiconductor saturable mirror

We report on a diode- pumped CW passively mode locked ceramic Nd: YAG laser with SESAM ( semiconductor saturable absorber mirror), wavelength 1064nm. At a pump power of 7.6w, the pulse width was estimated to be similar to 8.3ps with repetition rate similar to 130MHz and the average output power was 1.59w. To our knowledge, this was the first demonstration that ceramic Nd: YAG was used for diode pumped CW passively mode locking. (C) 2005 Optical Society of America.

Passive mode locking of diode-end-pumped Nd : GdVO4 laser with an In0.25Ga0.75As output coupler

Passive mode locking of a diode-pumped Nd:GdVO4 laser was demonstrated using In0.25Ga0.75As as saturable absorber as well as output coupler. The pulse width was measured to be about 16 ps with a repetition rate of 146 MHz. The average output power was 120 mW with pump power of 6 W. To our knowledge, this is the first demonstration on a passively mode-locked Nd:GdVO4 laser by using an In0.25Ga0.75As output coupler. (C) 2004 Elsevier B.V. All rights reserved.

Electroabsorption-Modulated DFB laser Integrated.With dual-core spot-size converters

A 1.55-mu m single shallow ridge electroabsorptionmodulated distributed feedback laser that is monolithically integrated with a buried-ridge-stripe dual-core spot-size converter (SSC) at the input and output ports was fabricated by combining selective area growth, quantum-well intermixing, and dual-core integration techniques simultaneously. These devices exhibit a threshold current of 34 mA, a side mode suppression ratio of 38.0 dB, a 3-dB modulation bandwidth of 11.0 GHz, and a modulator extinction ratio of 25.0 dB dc. The output beam divergence angles of the SSC in the horizontal and vertical directions are as small as 7.3 degrees x 18 degrees, respectively, resulting in 3.2-dB coupling loss with a cleaved single-mode optical fiber.

Diode-end-pumped passively CW mode-locked Nd : YLF laser by the LT-In0.25Ga0.75As absorber

We have demonstrated a self-staring passively continuous-wave mode-locked diode end-pumped Nd:YLF laser with a semiconductor saturable absorber mirror of single-quantum-well (In0.25Ga0.75As) grown by metal-organic chemical-vapor deposition technique at low temperature. The saturable absorber was used as nonlinear absorber and output coupler simultaneously. Stable pulse duration of 3 ps has been achieved at the repetition rate of 98 MHz. The average output power was 530 mW at 1053 nm under the incident pump power of 10 W, corresponding to the peak power of 1.8 kW and pulse energy of 5.4 nJ.

End-pumped continuous-wave passively modelocked Nd : YVO4 laser with low pump power

A simple cw mode-locked solid-state laser, which is end-pumped by a low-power laser diode, was demonstrated by optimizing the laser-mode size inside the gain medium. The optimum ratio between mode and pump spot sizes inside the laser crystal was estimated for a cw mode-locked laser, taking into account the input pump power. Calculation and experiment have shown that the optimum ratio was about 3 when the pump power is 2 W, which is different from the value regularly used in passively mode-locked solid-state lasers. This conclusion is also helpful in increasing the efficiency of high-power ultrashort lasers. (C) 2006 Society of Photo-Optical Instrumentation Engineers.

Electroabsorption modulated semiconductor optical amplifier monolithically integrated with spot-size converters

We have demonstrated an electroabsorption modulator (EAM) and semiconductor optical amplifier (SOA) monolithically integrated with novel dual-waveguide spot-size converters (SSCs) at the input and output ports for low-loss coupling to planar light-guide circuit silica waveguide or cleaved single-mode optical fiber. The device is fabricated by means of selective-area MOVPE growth (SAG), quantum well intermixing (QWI) and asymmetric twin waveguide (ATG) technologies with only three steps low-pressure MOVPE growth. For the device structure, in SOA/EAM section, double ridge structure was employed to reduce the EAM capacitances and enable high bit-rate operation. In the SSC sections, buried ridge stripe (BRS) were incorporated. Such a combination of ridge, ATG and BRS structure is reported for the first time in which it can take advantage of both easy processing of ridge structure and the excellent mode characteristic of BRS. At the wavelength range of 1550-1600 nm, lossless operation with extinction ratios of 25 dB DC and more than 10 GHz 3-dB bandwidth is successfully achieved. The beam divergence angles of the input and output ports of the device are as small as 8.0 degrees x 12.6 degrees, resulting in 3.0 dB coupling loss with cleaved single-mode optical fiber. (c) 2005 Elsevier B.V. All rights reserved.

A passively mode-locked diode-end-pumped Nd : YAG laser with a semiconductor saturable absorber mirror grown by metal organic chemical vapour deposition

We report the experimental results of a mode-locked diode-end-pumped Nd:YAG laser with a semiconductor saturable absorber mirror (SESAM) from which we achieved a 10 ps pulse duration at 150 MHz repetition rate. The SESAM was grown by metal organic chemical vapour deposition at low temperature. The recovery time was measured to be 0.5 ps, indicating the potential pulse compression to sub-picoseconds.