Shock-Induced Near-Wall Two-Phase Flow Structure Over a Micron-Sized Particles Bed

The present paper studies numerical modelling of near-wall two-phase flows induced by a normal shock wave moving at a constant speed, over a micronsized particles bed. In this two-fluid model, the possibility of particle trajectory intersection is considered and a full Lagrangian formulation of the dispersed phase is introduced. The finiteness of the Reynolds and Mach numbers of the flow around a particle as well as the fineness of the particle sizes are taken into account in describing the interactions between the carrier- and dispersed- phases. For the small mass-loading ratio case, the numerical simulation of flow structure of the two phases is implemented and the profiles of the particle number density are obtained under the constant-flux condition on the wall. The effects of the shock Mach number and the particle size and material density on particle entrainment motion are discussed in detail.The obtained results indicate that interphase non-equilibrium in the velocity and temperature is a common feature for this type of flows and a local particle accumulation zone may form near the envelope of the particle trajectory family.

冲击剪切载荷下SiC_P_6151Al复合材料变形局部化及增强颗粒尺寸效

利用特殊设计的“hat shape”试样,在分离式Hopkinson压杆和MTS通用材料试验机上实验研究了颗粒尺寸和应变率对颗粒增强金属基复合材料(SiC/6151Al)变形局部化行为的影响。结果表明：颗粒尺寸对复合材料的变形强化与变形局部化行为有显著影响。具体表现为：颗粒越小,复合材料流动应力越高,即强化效果越好；另一方面,对受载试样的微观检测发现,颗粒越小,复合材料剪切变形局部化越明显。同时发现,冲击载荷（高应变率）下复合材料更容易发生变形局部化。

Modeling of Ammonothermal Growth of Nitrides

Bulk single crystals of GaN and AlN can be grown from supercritical fluids using the ammonothermal method, which utilizes ammonia as fluid rather than water as in the hydrothermal process. In this process, a mineralizer such as amide, imide or nitride is used to attack a bulk nitride feedstock at temperatures from 200°C to 500°C and pressures from 1 to 4 kbar. Ammonothermal systems have been modeled here using fluid dynamics, thermodynamics and heat transfer models. The nutrient is considered as a porous media bed and the fluid flow is simulated using the Darcy-Brinkman-Forchheimer model. The resulting governing equations are solved using the finite volume method. The effects of particle size on flow pattern and temperature distribution in an autoclave are analyzed.

Laboratory-scale fluidized bed rig for high-temperature tube wastage studies

As part of a study of the wear of candidate heat exchanger tube materials for use in fluidized bed combustors, two similar laboratory-scale rigs have been built and characterized. Specimens of selected alloys are carried on counter-rotating rotors immersed in a fluidized bed, and are exposed to particle impact velocities of up to approximately 3 ms-1 at temperatures up to 1000°C. The performance of this design of apparatus has been investigated in detail. The effects of several experimental variables have been studied, including angle of particle impact, specimen speed, position of the rotor within the fluidized bed, duration of exposure, bed material particle size, degradation of the bed material, degree of fluidization of the bed, and size of specimen. In many cases the results obtained with steel specimens at elevated temperatures are similar to those observed with polymeric specimens at low temperatures.

Uplift resistance of buried pipelines at low cover-diameter ratios

Reliable estimates for the maximum available uplift resistance from the backfill soil are essential to prevent upheaval buckling of buried pipelines. The current design code DNV RP F110 does not offer guidance on how to predict the uplift resistance when the cover:pipe diameter (H/D) ratio is less than 2. Hence the current industry practice is to discount the shear contribution from uplift resitance for design scenarios with H/D ratios less than 1. The necessity of this extra conservatism is assessed through a series of full-scale and centrifuge tests, 21 in total, at the Schofield Centre, University of Cambridge. Backfill types include saturated loose sand, saturated dense sand and dry gravel. Data revealed that the Vertical Slip Surface Model remains applicable for design scenarios in loose sand, dense sand and gravel with H/D ratios less than 1, and that there is no evidence that the contribution from shear should be ignored at these low H/D ratios. For uplift events in gravel, the shear component seems reliable if the cover is more than 1-2 times the average particle size (D50), and more research effort is currenty being carried out to verify this conclusion. Strain analysis from the Particle Image Velocimetry (PIV) technique proves that the Vertical Slip Surface Model is a good representation of the true uplift deformation mechanism in loose sand at H/D ratios between 0.5 and 3.5. At very low H/D ratios (H/D < 0.5), the deformation mechanism is more wedge-like, but the increased contribution from soil weight is likely to be compensated by the reduced shear contributions. Hence the design equation based on the Vertical Slip Surface Model still produces good estimates for the maximum available uplift resistance. The evolution of shear strain field from PIV analysis provides useful insight into how uplift resistance is mobilized as the uplift event progresses. Copyright 2010, Offshore Technology Conference.

Deformation behavior and microstructure effect in 2124Al/SiCp composite

Dynamic compression tests were performed by means of a Split Hopkinson Pressure Bar (SHPB). Test materials were 2124Al alloys reinforced with 17% volume fraction of 3, 13 and 37 μm SiC particles, respectively. Under strain rate ε = 2100 l/s, SiC particles have a strong effect on σ_0.2 of the composites and the σ_0.2 increases with different SiC particle size in the following order: 2124Al-alloy → 124Al/SiC_p (37 μm) → 2124Al/SiC_p (13 μm) → 2124Al/SiC_p (3 μm), and the strain hardening of the composites depends mainly on the strain hardening of matrix, 2124A1 alloy. The results of dimensional analysis present that the flow stress of these composites not only depends on the property of reinforcement and matrix but also relates to the microstructure scale, matrix grain size, reinforcement size, the distance between reinforcements and dislocations in matrix. The normalized flow stress here is a function of inverse power of the edge-edge particle spacing, dislocation density and matrix grain size. Close-up observation shows that, in the composite containing SiC particles (3 μm), localized deformation formed readily comparing with other materials under the same loading condition. Microscopic observations indicate that different plastic flow patterns occur within the matrix due to the presence of hard particles with different sizes.

Evolution of thermoplastic shear localization and related microstructures in Awl/SiCp composites under dynamic compression

The localized shear deformation in the 2024 and 2124 Al matrix composites reinforced with SiC particles was investigated with a split Hopkinson pressure bar (SHPB) at a strain rate of about 2.0x10(3) s(-1). The results showed that the occurrence of localized shear deformation is sensitive to the size of SiC particles. It was found that the critical strain, at which the shear localization occurs, strongly depends on the size and volume fraction of SiC particles. The smaller the particle size, the lower the critical strain required for the shear localization. TEM examinations revealed that Al/SiCp interfaces are the main sources of dislocations. The dislocation density near the interface was found to be high and it decreases with the distance from the particles. The Al matrix in shear bands was highly deformed and severely elongated at low angle boundaries. The Al/SiCp interfaces, particularly the sharp corners of SiC particles, provide the sites for microcrack initiation. Eventual fracture is caused by the growth and coalescence of microcracks along the shear bands. It is proposed that the distortion free equiaxed grains with low dislocation density observed in the center of shear band result from recrystallization during dynamic deformation.

Toward an understanding of the turbidity measurement of fleterocoagulation rate constants of dispersions containing particles of different sizes

Our previous studies have shown that the determination of coagulation rate constants by turbidity measurement becomes impossible for a certain operating wavelength (that is, its blind point) because at this wavelength the change in the turbidity of a dispersion completely loses its response to the coagulation process. Therefore, performing the turbidity measurement in the wavelength range near the blind point should be avoided. In this article, we demonstrate that the turbidity measurement of the rate constant for coagulation of a binary dispersion containing particles of two different sizes (heterocoagulation) presents special difficulties because the blind point shifts with not only particle size but also with the component fraction. Some important aspects of the turbidity measurement for the heterocoagulation rate constant are discussed and experimentally tested. It is emphasized that the T-matrix method can be used to correctly evaluate extinction cross sections of doublets formed during the heterocoagulation process, which is the key data determining the rate constant from the turbidity measurement, and choosing the appropriate operating wavelength and component fraction are important to achieving a more accurate rate constant. Finally, a simple scheme in experimentally determining the sensitivity of the turbidity changes with coagulation over a wavelength range is proposed.

Ocean currents-induced pipeline lateral stability on sandy seabed

Unlike previous mechanical actuator loading methods, in this study, a hydrodynamic loading method was employed in a flow flume for simulating ocean currents induced submarine pipeline stability on a sandy seabed. It has been observed that, in the process of pipeline losing lateral stability in currents, there usually exist three characteristic times: (1) onset of sand scour; (2) slight lateral displacement of pipeline; and (3) breakout of pipeline. An empirical linear relationship is established between the dimensionless submerged weight of pipeline and Froude number for describing pipeline lateral stability in currents, in which the current-pipe-soil coupling effects are reflected. Scale effects are examined with the method of "modeling of models," and the sand particle size effects on pipeline stability are also discussed. Moreover, the pipeline stability in currents is compared with that in waves, which indicates that the pipeline laid directly upon the sandy seabed is more laterally stable in currents than in waves.

Evaluation of influence of multiple scattering effect in light-scattering-based applications

The extinction cross sections of a system containing two particles are calculated by the T-matrix method, and the results are compared with those of two single particles with single-scattering approximation. The necessity of the correction of the refractive indices of water and polystyrene for different incident wavelengths is particularly addressed in the calculation. By this means, the volume fractions allowed for certain accuracy requirements of single-scattering approximation in the light scattering experiment can be evaluated. The volume fractions calculated with corrected refractive indices are compared with those obtained with fixed refractive indices which have been rather commonly used, showing that fixed refractive indices may cause significant error in evaluating multiple scattering effect. The results also give a simple criterion for selecting the incident wavelength and particle size to avoid the 'blind zone' in the turbidity measurement, where the turbidity change is insensitive to aggregation of two particles.

SiC_p/6151Al复合材料的微结构效应

利用分离式Hopkinson压杆和MTS通用材料试验机研究了SiC_p/6151Al颗粒增强复合材料在不同应变率下的变形行为和增强颗粒的尺寸对复合材料微结构及变形行为的影响。结果表明，对于在不同应变率下的SiC_p/6151Al复合材料，增强颗粒尺寸大小的流动应力高于增强颗粒尺寸的流动应力。根据位错强化理论中的Hall-Petch关系对这个结果进行了解释。首次在实验上观测到增强颗粒对复合材料微损伤-微带形成的影响，并根据微带（microband）形成的双位错墙理论（double dislocation walls）, 分析了增强颗粒对复合材料微带损伤及力学性能影响的微结构效应。

冲击剪切载荷下SiC_P/6151Al复合材料变形局部化及增强颗粒尺寸效应

利用特殊设计的“hat shape”试样，在分离式Hopkinson压杆和MTS通用材料试验机上实验研究了颗粒尺寸和应变率对颗粒增强金属基复合材料（SiC_P/6151Al）变形局部化行为的影响。结果表明：颗粒尺寸对复合材料的变形强化与变形局部化行为有显著影响。具体表现为：颗粒越小，复合材料流动应力越高，即强化效果越好；另一方面，对受载试样的微观检测发现，颗粒越小，复合材料剪切变形局部分越明显。同时发现，冲击载荷（高应变率）下复合材料更容易发生变形局部化。

A Synoptic View of a Coastal Plain Estuary.

During October, 1972 the Patuxent River Estuary was monitored intensively and synoptically over two tidal cycles to determine the spatial and temporal patterns of various hydrodynamic, chemical and biological features. Forty-one depths at eleven stations along nine transects were sampled simultaneously at hourly intervals for salinity, temperature, dissolved oxygen, chlorohyll a, particulate nitrogen, nitrate, nitrite, total kjeldahl nitrogen, ammonia, particulate carbohydrate, dissolved organic carbon, total hydrolizable phosphorous, dissolved inorganic phosphorous, suspended sediment, particle size distribution, and zooplankton. Tidal velocity was continuously monitored at each depth by recording current meters. Riverine input and meteorological conditions were relatively stable for two weeks preceeding the deployment. This communication describes the calculation of the intrinsic rates of change of the observed variables from their measured distributions in the Estuary. The steady-state, one-dimensional equation of species continuity is employed to separate the advection and tidal dispersion of a hydrodynamically passive substance frbm its intrinsic rate of change at point. A new spatial transform is introduced for the purpose of interpolation and extrapolation of data.The intrinsic rate of change profiles reveal a region of heavy bloom activity in the upper estuary and a secondary bloom near the point in the River that most of the suspended material settles out. The changes in ammonia and nitrates are highly correlated to the productivity patterns. Phosphorous rates are less closely correlated to productivity. The perturbations that the Chalk Point steam electric power plant have on the heat and oxygen balances are easily discernible.

Experimental Study of Pipeline Stability on Sandy Seabed under the Influence of Ocean Currents

Ocean-current-induced pipeline stability on sandy seabed was simulated physically in a flow flume. The process of pipeline losing onbottom stability in currents was recorded and analyzed. Experimental data show that, for a pipeline directly laid on sandy seabed, there exists a linear relationship between the dimensionless submerged weight of pipeline and Froude number, in which the current-pipe-soil coupling effects are reflected. The sand-particle size effects on pipeline onbottom stability are further discussed. The new established empirical relationship may provide a guide for the engineering practice of current-induced on-bottom stability design of a submarine pipeline.

Shock-Induced Dust Cloud Over a Deposit Layer of Fine Particles

The present paper investigates particle density pro les of a dust cloud induced by a normal shock wave moving at a constant speed along a at surface deposited with ne particles. In shock-fixxed coordinates, numerical simulation of ow structures of the carrier- and dispersed- phases was performed for the M = 2 case. The neness and non-uniformity of the particle size are taken into account and their effcts on the dust cloud are discussed in detail.