Modeling of water/steam circulation in Circulating Fluidized Bed boiler

A distinctive design feature of steam boiler with natural circulation is the presence of the steam drum which plays a role of the separator of vapor from the flow of water-and-steam mixture coming into steam drum from the furnace tubes. Steam drum with unheated downcomer tubes, deducing from it, and riser (screen/furnace tubes) inside the furnace is a closed circulation loop in which movement of water (downcomer tubes) and water-and-steam mixture (riser tubes) is organized. The movement of the working fluid is appears due to occurrence of the natural pressure, determined by the difference in hydrostatic pressure and the mass of water and water-and-steam mixtures in downcomer and riser tubes and called the driving pressure of the natural circulation: S drive = H steam (ρ down + ρ mix) g where: ρ down - density of water in downcomer tubes; ρ mix - density of water in riser tubes; H steam - height of steam content section; g - acceleration of gravity. In steam boilers with natural circulation the circulation rate is usually between 10 and 30. Thus, consumption of water in the circulation circuit “circulation rate times” more than steam output of the boiler. There are two aspects of the design of natural water circulation loops. One is to ensure a sufficient mass flux of circulating water to avoid burnout of evaporator tubes. The other is to avoid tube wall temperature fluctuation and tube vibration due to oscillation of circulation velocity. The design criteria are therefore reduced, in principle, to those of critical heat flux, critical flow rate for burnout, and flow instability. In practical design, however, the circulation velocity and the void fraction at the evaporator tube outlet are used as the design criteria (Seikan I., et. al., 1999). This study has been made with assumption that the heat flux in the furnace of the boiler even all the time. The target of the study was to define the circulation rate of the boiler, thus average heat flux do not change it. I would like to acknowledge professionals from “Foster Wheeler” company for good and comfortable cooperation.

Estimation of standard enthalpy of formation of alkanes in gaseous state by calculating size, structural and electronic parameters in the molecules

A quantitative analysis is made on the correlation ship of thermodynamic property, i.e., standard enthalpy of formation (ΔH fº) with Kier's molecular connectivity index(¹Xv),vander waal's volume (Vw) electrotopological state index (E) and refractotopological state index (R) in gaseous state of alkanes. The regression analysis reveals a significant linear correlation of standard enthalpy of formation (ΔH fº) with ¹Xv, Vw, E and R. The equations obtained by regression analysis may be used to estimate standard enthalpy of formation (ΔH fº) of alkanes in gaseous state.

Jatkuvatoiminen ioninvaihto ja kompleksoituvien metallien sorptio kloridiympäristössä

Työn tarkoituksena oli tutkia kompleksoituvien metallien erotusta kloridiliuoksesta ioninvaihdolla. Kirjallisessa osassa perehdyttiin metallikompleksien muodostumiseen, ja erityisesti hopean, kalsiumin, magnesiumin, lyijyn ja sinkin muodostamiin komplekseihin kloridin ja nitraatin kanssa. Kirjallisessa osassa käsiteltiin myös metallien erottamista kiintopetikolonneissa jatkuvatoimisilla ioninvaihtomenetelmillä. Tässä työssä jatkuvatoimisen ioninvaihdon prosessivaihtoehdot jaoteltiin pyöriviin ja paikallaan pysyviin kolonneihin, sekä tarkasteltiin eri prosessivaihtoehtoja kolonnien kytkentöjen suhteen. Työn kokeellisessa osassa tutkittiin kahdenarvoisten metallien erottamista yhdenarvoisista metalleista sekä luotiin koedataa vastaavanlaisen erotusprosessin simulointiin. Kokeissa käytettiin anioninvaihtohartsia ja kelatoivaa selektiivistä ioninvaihtohartsia. Kahdenarvoisen kalsiumin, magnesiumin, lyijyn ja sinkin adsorptiota hartseihin tutkittiin tasapaino-, kinetiikka- ja kolonnikokeilla. Anioninvaihtohartsilla tehtyjen tasapaino- ja kolonnikokeiden tulokset osoittivat, että hartsi adsorboi tehokkaasti sinkkiä kloridiliuoksista, koska sinkki muodostaa stabiileja anionisia klorokomplekseja. Muiden tutkittujen kahdenarvoisten metallien adsorptio hartsiin oli huomattavasti vähäisempää. Tulosten perusteella tutkittu anioninvaihtohartsi on hyvä vaihtoehto sinkin erottamiseen muista tutkituista kahdenarvoisista metalleista kloridiympäristössä. Kelatoivalla hartsilla tehdyt tasapaino- ja kolonnikokeet osoittivat, että hartsi adsorboi kloridiliuoksista hyvin kahdenarvoista kalsiumia, magnesiumia, lyijyä ja sinkkiä, mutta ei adsorboi yhdenarvoista hopeaa. Tulosten perusteella kahdenarvoisten metallien erottaminen yhdenarvoisista metalleista voidaan toteuttaa kokeissa käytetyllä kelatoivalla ioninvaihtohartsilla.

Quasi-objects and actors in the web of belief. Formation of a national nuclear waste management system: the case of Finland

Paper presented in ISA RC23 meeting, Gothenburg July 16th 2010

A study of combustion phenomena in circulating fluidized beds by developing and applying experimental and modelling methods for laboratory-scale reactors

The results shown in this thesis are based on selected publications of the 2000s decade. The work was carried out in several national and EC funded public research projects and in close cooperation with industrial partners. The main objective of the thesis was to study and quantify the most important phenomena of circulating fluidized bed combustors by developing and applying proper experimental and modelling methods using laboratory scale equipments. An understanding of the phenomena plays an essential role in the development of combustion and emission performance, and the availability and controls of CFB boilers. Experimental procedures to study fuel combustion behaviour under CFB conditions are presented in the thesis. Steady state and dynamic measurements under well controlled conditions were carried out to produce the data needed for the development of high efficiency, utility scale CFB technology. The importance of combustion control and furnace dynamics is emphasized when CFB boilers are scaled up with a once through steam cycle. Qualitative information on fuel combustion characteristics was obtained directly by comparing flue gas oxygen responses during the impulse change experiments with fuel feed. A one-dimensional, time dependent model was developed to analyse the measurement data Emission formation was studied combined with fuel combustion behaviour. Correlations were developed for NO, N2O, CO and char loading, as a function of temperature and oxygen concentration in the bed area. An online method to characterize char loading under CFB conditions was developed and validated with the pilot scale CFB tests. Finally, a new method to control air and fuel feeds in CFB combustion was introduced. The method is based on models and an analysis of the fluctuation of the flue gas oxygen concentration. The effect of high oxygen concentrations on fuel combustion behaviour was also studied to evaluate the potential of CFB boilers to apply oxygenfiring technology to CCS. In future studies, it will be necessary to go through the whole scale up chain from laboratory phenomena devices through pilot scale test rigs to large scale, commercial boilers in order to validate the applicability and scalability of the, results. This thesis shows the chain between the laboratory scale phenomena test rig (bench scale) and the CFB process test rig (pilot). CFB technology has been scaled up successfully from an industrial scale to a utility scale during the last decade. The work shown in the thesis, for its part, has supported the development by producing new detailed information on combustion under CFB conditions.

Effect of pulps fractionation on formation and strength properties of laboratory hand sheets

The objectives of the work were to study the effect of dewatering time varying on formation properties of papersheets, to determine the role of fines fraction in creation of paper with good formation and strength properties of papersheets, and also to study the effect of charge modification of fibers fractionations on formation properties of handsheets. The paper formation is one of the most important structural properties of paper. This property has effect on physical and optical characteristics of paper. In thi work the effect of formation on tensile strength was determined. The formation properties were analyzed by using the AMBERTEC Beta Formation Tester. The PAM addition as a f;locculant agent did some changes in the formation of paper. Paper sheets were also made from different furnishes of both birch and pine pulps. The fibers particles as a fines have great effect on drainability changes. Fines fraction played important role in papermaking. The two kinds of pulps (pine and birch pulps) were also used in this work for investigation of fines role. As it was expected the fines fraction gave positive effect on paper formation, but when fines fraction was added above initial fines content the formation of paper was deteriorated. The effect of paper formation on tensile strength was also determined. In many cases the poor formation of paper had negative effect on strength properties of paper..

Formation of polyelectrolyte multilayers and polyelectrolyte complexes in dual polymer treatment of papermaking pulp

The goal of this study was to find a new approach to modify chemically the properties of paper by improving fiber quality. This Master’s thesis includes the multiple polymer treatment in general and themeasurement methods with which the formation of multilayers and complexes can be noticed. The treatment by an oppositely charged dual polymer system is a good approach to increase paper strength. In this work, starch, a cationic polymer, and carboxymethyl cellulose (CMC), an anionic polymer, were used step-by-step to improve paper strength. The adsorption of cationic starch and CMC on cellulose fibers were analyzed via polyelectrolyte titration. The results showed that paper strength was enhanced slightly with a layer-by-layer assembly of the polymers. However, if the washing stage, which was required for layer-by-layer assembly, was eliminated, the starch/CMC complex was deposited on fibers more efficiently, and the paper strength was improved more significantly.

Model development for circulating fluidized bed boiler operation

Comprehensive understanding of the heat transfer processes that take place during circulating fluidized bed (CFB) combustion is one of the most important issues in CFB technology development. This leads to possibility of predicting, evaluation and proper design of combustion and heat transfer mechanisms. The aim of this thesis is to develop a model for circulating fluidized bed boiler operation. Empirical correlations are used for determining heat transfer coefficients in each part of the furnace. The proposed model is used both in design and offdesign conditions. During off-design simulations fuel moisture content and boiler load effects on boiler operation have been investigated. In theoretical part of the thesis, fuel properties of most typical classes of biomass are widely reviewed. Various schemes of biomass utilization are presented and, especially, concerning circulating fluidized bed boilers. In addition, possible negative effects of biomass usage in boilers are briefly discussed.

In vitro ectomycorrhiza formation by monokaryotic and dikaryotic isolates of Pisolithus microcarpus in Eucalyptus grandis

The formation of ectomycorrhizas by monokaryotic and dikaryotic isolates of Pisolithus microcarpus (Cooke & Massee) G. Cunn. in Eucalyptus grandis W. Hill ex Maid. was studied by in vitro synthesis in Petri dishes. The formation of ectomycorrhizas was observed for all strains tested. Ectomycorrhizas formed by the monokaryotic strains presented a sheath of hyphae around the roots and a Hartig net limited to the epidermis layer, typical of the angiosperm ectomycorrhizas. Colonization rates, a measure of the number of ectomycorrhizas in relation to the total number of lateral root tips, varied from 23 to 62%. Some monokaryotic strains stimulated the formation of lateral roots, promoting increases of up to 109% above the control. The presence of some of the isolates in the in vitro synthesis medium stimulated the production of thicker lateral root tips. The dimensions of the lateral roots tips and ectomycorrhizas varied from one isolate to the next, indicating a variation in their capacity to provoke morphological changes in the host plant roots. The dikaryotic strain M5M11 presented higher values for lateral root yield, number of ectomycorrhizas, and colonization percentage than the corresponding monokaryotic strains, M5 and M11. This indicated the possibility of selecting compatible performing monokaryotic isolates for the yield of superior dikaryotic strains. The set of monokaryotic strains tested varied greatly in their ability to colonize E. grandis roots and cause secondary metabolism-related morphological changes in roots, providing a wealth of model systems for the study of genetic, physiological, and morphogenetic processes involved in Pisolithus-Eucalyptus ectomycorrhiza formation.

Recovery and refining of manganese as by-product from hydrometallurgical processes

The consumption of manganese is increasing, but huge amounts of manganese still end up in waste in hydrometallurgical processes. The recovery of manganese from multi-metal solutions at low concentrations may not be economical. In addition, poor iron control typically prevents the production of high purity manganese. Separation of iron from manganese can be done with chemical precipitation or solvent extraction methods. Combined carbonate precipitation with air oxidation is a feasible method to separate iron and manganese due to the fast kinetics, good controllability and economical reagents. In addition the leaching of manganese carbonate is easier and less acid consuming than that of hydroxide or sulfide precipitates. Selective iron removal with great efficiency from MnSO4 solution is achieved by combined oxygen or air oxidation and CaCO3 precipitation at pH > 5.8 and at a redox potential of > 200 mV. In order to avoid gypsum formation, soda ash should be used instead of limestone. In such case, however, extra attention needs to be paid on the reagents mole ratios in order to avoid manganese coprecipitation. After iron removal, pure MnSO4 solution was obtained by solvent extraction using organophosphorus reagents, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and bis(2,4,4- trimethylpentyl)phosphinic acid (CYANEX 272). The Mn/Ca and Mn/Mg selectivities can be increased by decreasing the temperature from the commonly used temperatures (40 –60oC) to 5oC. The extraction order of D2EHPA (Ca before Mn) at low temperature remains unchanged but the lowering of temperature causes an increase in viscosity and slower phase separation. Of these regents, CYANEX 272 is selective for Mn over Ca and, therefore, it would be the better choice if there is Ca present in solution. A three-stage Mn extraction followed by a two-stage scrubbing and two-stage sulfuric acid stripping is an effective method of producing a very pure MnSO4 intermediate solution for further processing. From the intermediate MnSO4 some special Mn- products for ion exchange applications were synthesized and studied. Three types of octahedrally coordinated manganese oxide materials as an alternative final product for manganese were chosen for synthesis: layer structured Nabirnessite, tunnel structured Mg-todorokite and K-kryptomelane. As an alternative source of pure MnSO4 intermediate, kryptomelane was synthesized by using a synthetic hydrometallurgical tailings. The results show that the studied OMS materials adsorb selectively Cu, Ni, Cd and K in the presence of Ca and Mg. It was also found that the exchange rates were reasonably high due to the small particle dimensions. Materials are stable in the studied conditions and their maximum Cu uptake capacity was 1.3 mmol/g. Competitive uptake of metals and acid was studied using equilibrium, batch kinetic and fixed-bed measurements. The experimental data was correlated with a dynamic model, which also accounts for the dissolution of the framework manganese. Manganese oxide micro-crystals were also bound onto silica to prepare a composite material having a particle size large enough to be used in column separation experiments. The MnOx/SiO2 ratio was found to affect significantly the properties of the composite. The higher the ratio, the lower is the specific surface area, the pore volume and the pore size. On the other hand, higher amount of silica binder gives composites better mechanical properties. Birnesite and todorokite can be aggregated successfully with colloidal silica at pH 4 and with MnO2/SiO2 weight ratio of 0.7. The best gelation and drying temperature was 110oC and sufficiently strong composites were obtained by additional heat-treatment at 250oC for 2 h. The results show that silica–supported MnO2 materials can be utilized to separate copper from nickel and cadmium. The behavior of the composites can be explained reasonably well with the presented model and the parameters estimated from the data of the unsupported oxides. The metal uptake capacities of the prepared materials were quite small. For example, the final copper loading was 0.14 mmol/gMnO2. According to the results the special MnO2 materials are potential for a specific environmental application to uptake harmful metal ions.

Modeling of electrolyte sorption – from phase equilibria to dynamic separation systems

In this thesis, general approach is devised to model electrolyte sorption from aqueous solutions on solid materials. Electrolyte sorption is often considered as unwanted phenomenon in ion exchange and its potential as an independent separation method has not been fully explored. The solid sorbents studied here are porous and non-porous organic or inorganic materials with or without specific functional groups attached on the solid matrix. Accordingly, the sorption mechanisms include physical adsorption, chemisorption on the functional groups and partition restricted by electrostatic or steric factors. The model is tested in four Cases Studies dealing with chelating adsorption of transition metal mixtures, physical adsorption of metal and metalloid complexes from chloride solutions, size exclusion of electrolytes in nano-porous materials and electrolyte exclusion of electrolyte/non-electrolyte mixtures. The model parameters are estimated using experimental data from equilibrium and batch kinetic measurements, and they are used to simulate actual single-column fixed-bed separations. Phase equilibrium between the solution and solid phases is described using thermodynamic Gibbs-Donnan model and various adsorption models depending on the properties of the sorbent. The 3-dimensional thermodynamic approach is used for volume sorption in gel-type ion exchangers and in nano-porous adsorbents, and satisfactory correlation is obtained provided that both mixing and exclusion effects are adequately taken into account. 2-Dimensional surface adsorption models are successfully applied to physical adsorption of complex species and to chelating adsorption of transition metal salts. In the latter case, comparison is also made with complex formation models. Results of the mass transport studies show that uptake rates even in a competitive high-affinity system can be described by constant diffusion coefficients, when the adsorbent structure and the phase equilibrium conditions are adequately included in the model. Furthermore, a simplified solution based on the linear driving force approximation and the shrinking-core model is developed for very non-linear adsorption systems. In each Case Study, the actual separation is carried out batch-wise in fixed-beds and the experimental data are simulated/correlated using the parameters derived from equilibrium and kinetic data. Good agreement between the calculated and experimental break-through curves is usually obtained indicating that the proposed approach is useful in systems, which at first sight are very different. For example, the important improvement in copper separation from concentrated zinc sulfate solution at elevated temperatures can be correctly predicted by the model. In some cases, however, re-adjustment of model parameters is needed due to e.g. high solution viscosity.

TEMPERATURE AND SUBSTRATE INFLUENCES ON SEED GERMINATION AND SEEDLING FORMATION IN Callisthene fasciculata Mart. (VOCHYSIACEAE) IN THE LABORATORY1

ABSTRACTCallisthene fasciculata Mart. is a tree belonging to the Vochysiaceae family. Its wood is moderately heavy and resistant and used to make poles, beams, and other structures. The aim of this work was to evaluate seed germination and the initial growth of seedlings of C. fasciculata at different temperatures and in different substrates. Seeds were collected from fruits in the Pantanal de Miranda, Mato Grosso do Sul state, Brazil. In one experiment, the seeds were subjected to constant temperatures of 20, 25, 30 and 35 °C and to alternating temperatures of 20-30 and 25-35 °C (on paper substrate). In another experiment, the seeds were subjected to temperatures of 20 and 25 °C on three substrates (sand, vermiculite and between paper) in a germinator. The experiment had a randomized design, with four replicates of 25 seeds per treatment. The F-values obtained for germination indicated no significant effect of substrate or temperature on the final germination percentage. The analyses revealed no effect of a treatment interaction (temperature x substrate) on either germination or average germination time; however, a treatment interaction effect was observed on the germination speed index. The treatment combinations yielding the best performance were between paper substrate at 20 °C and sand substrate at 25 °C. There was a significant effect of the interaction between temperature and substrate on seedling growth, with increased root growth observed in the between paper substrate at 25 °C and increased aerial component growth in both sand at 20 °C and vermiculite at 25 °C. The between paper treatment at 25 °C yielded the greatest final seedling size. Between paper is the most recommended substrate for the production of seedlings due to its ease of handling and lower probability of contamination.

Modeling study of limestone reactions in fluidized bed conditions

Traditionally limestone has been used for the flue gas desulfurization in fluidized bed combustion. Recently, several studies have been carried out to examine the use of limestone in applications which enable the removal of carbon dioxide from the combustion gases, such as calcium looping technology and oxy-fuel combustion. In these processes interlinked limestone reactions occur but the reaction mechanisms and kinetics are not yet fully understood. To examine these phenomena, analytical and numerical models have been created. In this work, the limestone reactions were studied with aid of one-dimensional numerical particle model. The model describes a single limestone particle in the process as a function of time, the progress of the reactions and the mass and energy transfer in the particle. The model-based results were compared with experimental laboratory scale BFB results. It was observed that by increasing the temperature from 850 °C to 950 °C the calcination was enhanced but the sulfate conversion was no more improved. A higher sulfur dioxide concentration accelerated the sulfation reaction and based on the modeling, the sulfation is first order with respect to SO2. The reaction order of O2 seems to become zero at high oxygen concentrations.