Influences of deep convective cloud systems on tropospheric trace gases and photochemistry over the tropical West Pacific

A numerical model for studying the influences of deep convective cloud systems on photochemistry was developed based on a non-hydrostatic meteorological model and chemistry from a global chemistry transport model. The transport of trace gases, the scavenging of soluble trace gases, and the influences of lightning produced nitrogen oxides (NOx=NO+NO2) on the local ozone-related photochemistry were investigated in a multi-day case study for an oceanic region located in the tropical western Pacific. Model runs considering influences of large scale flows, previously neglected in multi-day cloud resolving and single column model studies of tracer transport, yielded that the influence of the mesoscale subsidence (between clouds) on trace gas transport was considerably overestimated in these studies. The simulated vertical transport and scavenging of highly soluble tracers were found to depend on the initial profiles, reconciling contrasting results from two previous studies. Influences of the modeled uptake of trace gases by hydrometeors in the liquid and the ice phase were studied in some detail for a small number of atmospheric trace gases and novel aspects concerning the role of the retention coefficient (i.e. the fraction of a dissolved trace gas that is retained in the ice phase upon freezing) on the vertical transport of highly soluble gases were illuminated. Including lightning NOx production inside a 500 km 2-D model domain was found to be important for the NOx budget and caused small to moderate changes in the domain averaged ozone concentrations. A number of sensitivity studies yielded that the fraction of lightning associated NOx which was lost through photochemical reactions in the vicinity of the lightning source was considerable, but strongly depended on assumptions about the magnitude and the altitude of the lightning NOx source. In contrast to a suggestion from an earlier study, it was argued that the near zero upper tropospheric ozone mixing ratios which were observed close to the study region were most probably not caused by the formation of NO associated with lightning. Instead, it was argued in agreement with suggestions from other studies that the deep convective transport of ozone-poor air masses from the relatively unpolluted marine boundary layer, which have most likely been advected horizontally over relatively large distances (both before and after encountering deep convection) probably played a role. In particular, it was suggested that the ozone profiles observed during CEPEX (Central Equatorial Pacific Experiment) were strongly influenced by the deep convection and the larger scale flow which are associated with the intra-seasonal oscillation.

Numerical and analytical approaches to strongly correlated electron systems

In this thesis we consider three different models for strongly correlated electrons, namely a multi-band Hubbard model as well as the spinless Falicov-Kimball model, both with a semi-elliptical density of states in the limit of infinite dimensions d, and the attractive Hubbard model on a square lattice in d=2. In the first part, we study a two-band Hubbard model with unequal bandwidths and anisotropic Hund's rule coupling (J_z-model) in the limit of infinite dimensions within the dynamical mean-field theory (DMFT). Here, the DMFT impurity problem is solved with the use of quantum Monte Carlo (QMC) simulations. Our main result is that the J_z-model describes the occurrence of an orbital-selective Mott transition (OSMT), in contrast to earlier findings. We investigate the model with a high-precision DMFT algorithm, which was developed as part of this thesis and which supplements QMC with a high-frequency expansion of the self-energy. The main advantage of this scheme is the extraordinary accuracy of the numerical solutions, which can be obtained already with moderate computational effort, so that studies of multi-orbital systems within the DMFT+QMC are strongly improved. We also found that a suitably defined Falicov-Kimball (FK) model exhibits an OSMT, revealing the close connection of the Falicov-Kimball physics to the J_z-model in the OSM phase. In the second part of this thesis we study the attractive Hubbard model in two spatial dimensions within second-order self-consistent perturbation theory. This model is considered on a square lattice at finite doping and at low temperatures. Our main result is that the predictions of first-order perturbation theory (Hartree-Fock approximation) are renormalized by a factor of the order of unity even at arbitrarily weak interaction (U->0). The renormalization factor q can be evaluated as a function of the filling n for 00, the q-factor vanishes, signaling the divergence of self-consistent perturbation theory in this limit. Thus we present the first asymptotically exact results at weak-coupling for the negative-U Hubbard model in d=2 at finite doping.

The influence of heat treatment on the phase relations in mineral growth systems

ABSTRACT Corundum is one of the most famous gems materials. Different heat treatment methods for enhancement purposes are commonly applied and accepted in the gem market. With this reason, the identification of the natural, unheated corundum is intensively investigated. In this study, aluminium hydroxide minerals and zircon are focused to observe the crystallization and phase change of these minerals during heat treatment procedures. Aluminium hydroxide minerals can be transformed to alumina with the corundum structure by heating. The reaction history of aluminium hydroxide minerals containing corundum was investigated comparing it with diaspore, boehmite, gibbsite and bayerite by TG and DTA methods. These hydroxide minerals were entirely transformed to corundum after heating at 600°C. Zircon inclusions in corundums from Ilakaka, Madagascar, were investigated for the influence of different heat-treatment temperatures on the recovery of their crystalline structure and on possible reactions within and with the host crystals. The host corundum was heated at 500, 800, 1000, 1200, 1400, 1600 and 1800°C. The crystallinity, the trapped pressure, and the decomposition of the zircon inclusions within the host corundum have been investigated by Raman spectroscopy. Radiation-damaged zircon inclusions may be used as an indicator for unheated Ilakaka corundum crystals. They are fully recrystallized after heating at 1000°C influencing the lowering of the 3 Raman band shift, the decreasing of FWHM of the 3 Raman band and the decreasing of the trapped pressure between the inclusion and the host corundum. Under microscopic observation, surface alterations of the inclusions can be firstly seen from transparent into frosted-like appearance at 1400°C. Then, between 1600°C and 1800 °C, the inclusion becomes partly or even completely molten. The decomposition of the zircon inclusion to m-ZrO2 and SiO2-glass phases begins at the rim of the inclusion after heating from 1200°C to 1600°C which can be detected by the surface change, the increase of the 3 Raman band position and the trapped pressure. At 1800°C, the zircon inclusions entirely melt transforming to solid phases during cooling like m-ZrO2 and SiO2-glass accompanied by an increase of pressure between the transformed inclusion and its host.

Expression profiling und rationale Expressionsoptimierung am Beispiel eines prokaryontischen Wirt-,Vektor-Systems

Durch globale Expressionsprofil-Analysen auf Transkriptom-, Proteom- oder Metabolom-Ebene können biotechnologische Produktionsprozesse besser verstanden und die Erkenntnisse für die zielgerichtete, rationale Optimierung von Expressionssystemen genutzt werden. In der vorliegenden Arbeit wurde die Überexpression einer Glukose-Dehydrogenase (EC 1.1.5.2), die von der Roche Diagnostics GmbH für die diagnostische Anwendung optimiert worden war, in Escherichia coli untersucht. Die Enzymvariante unterscheidet sich in sieben ihrer 455 Aminosäuren vom Wildtyp-Enzym und wird im sonst isogenen Wirt-/Vektor-System in signifikant geringeren Mengen (Faktor 5) gebildet. Das prokaryontische Expressionssystem wurde auf Proteom-Ebene charakterisiert. Die 2-dimensionale differenzielle Gelelektrophorese (DIGE) wurde zuvor unter statistischen Aspekten untersucht. Unter Berücksichtigung von technischen und biologischen Variationen, falsch-positiven (α-) und falsch-negativen (β-) Fehlern sowie einem daraus abgeleiteten Versuchsdesign konnten Expressionsunterschiede als signifikant quantifiziert werden, wenn sie um den Faktor ≥ 1,4 differierten. Durch eine Hauptkomponenten-Analyse wurde gezeigt, dass die DIGE-Technologie für die Expressionsprofil-Analyse des Modellsystems geeignet ist. Der Expressionsstamm für die Enzymvariante zeichnete sich durch eine höhere Variabilität an Enzymen für den Zuckerabbau und die Nukleinsäure-Synthese aus. Im Expressionssystem für das Wildtyp-Enzym wurde eine unerwartet erhöhte Plasmidkopienzahl nachgewiesen. Als potenzieller Engpass in der Expression der rekombinanten Glukose-Dehydrogenase wurde die Löslichkeitsvermittlung identifiziert. Im Expressionsstamm für das Wildtyp-Enzym wurden viele Proteine für die Biogenese der äußeren Membran verstärkt exprimiert. Als Folge dessen wurde ein sog. envelope stress ausgelöst und die Zellen gingen in die stationäre Wuchsphase über. Die Ergebnisse der Proteomanalyse wurden weiterführend dazu genutzt, die Produktionsleistung für die Enzymvariante zu verbessern. Durch den Austausch des Replikationsursprungs im Expressionsvektor wurde die Plasmidkopienzahl erhöht und die zelluläre Expressionsleistung für die diagnostisch interessantere Enzymvariante um Faktor 7 - 9 gesteigert. Um die Löslichkeitsvermittlung während der Expression zu verbessern, wurde die Plasmidkopienzahl gesenkt und die Coexpression von Chaperonen initiiert. Die Ausbeuten aktiver Glukose-Dehydrogenase wurden durch die Renaturierung inaktiven Produkts aus dem optimierten Expressionssystem insgesamt um einen Faktor von 4,5 erhöht. Somit führte im Rahmen dieser Arbeit eine proteombasierte Expressionsprofil-Analyse zur zielgerichteten, rationalen Expressionsoptimierung eines prokaryontischen Modellsystems.

Effect of drug physicochemical properties on the release from liposomal systems in vitro and in vivo

Liposomes were discovered about 40 years ago by A. Bangham and since then they became very versatile tools in biology, biochemistry and medicine. Liposomes are the smallest artificial vesicles of spherical shape that can be produced from natural untoxic phospholipids and cholesterol. Liposome vesicles can be used as drug carriers and become loaded with a great variety of molecules, such as small drug molecules, proteins, nucleotides and even plasmids. Due to the variability of liposomal compositions they can be used for a large number of applications. In this thesis the β-adrenoceptor antagonists propranolol, metoprolol, atenolol and pindolol, glucose, 18F-Fluorodeoxyglucose (FDG) and Er-DTPA were used for encapsulation in liposomes, characterization and in vitro release studies. Multilamellar vesicles (MLV), large unilamellar vesicles (LUV) and smaller unilamellar vesicles (SUV) were prepared using one of the following lipids: 1,2-Dimyristoyl-sn-Glycero-3-Phosphocholine (DMPC), 1,2-Distearoyl-sn-Glycero-3-Phosphocholine (DSPC), Phospholipone 90H (Ph90H) or a mixture of DSPC and DMPC (1:1). The freeze thawing method was used for preparation of liposomes because it has three advantages (1) avoiding the use of chloroform, which is used in other methods and causes toxicity (2) it is a simple method and (3) it gives high entrapping efficiency. The percentage of entrapping efficiencies (EE) was different depending on the type and phase transition temperature (Tc) of the lipid used. The average particle size and particle size distribution of the prepared liposomes were determined using both dynamic light scattering (DLS) and laser diffraction analyzer (LDA). The average particle size of the prepared liposomes differs according to both liposomal type and lipid type. Dispersion and dialysis techniques were used for the study of the in vitro release of β-adrenoceptor antagonists. The in vitro release rate of β-adrenoceptor antagonists was increased from MLV to LUV to SUV. Regarding the lipid type, β-adrenoceptor antagonists exhibited different in vitro release pattern from one lipid to another. Two different concentrations (50 and 100mg/ml) of Ph90H were used for studying the effect of lipid concentration on the in vitro release of β-adrenoceptor antagonists. It was found that liposomes made from 50 mg/ml Ph90H exhibited higher release rates than liposomes made at 100 mg/ml Ph90H. Also glucose was encapsulated in MLV, LUV and SUV using 1,2-Dimyristoyl-sn-Glycero-3-Phosphocholine (DMPC), 1,2-Distearoyl-sn-Glycero-3-Phosphocholine (DSPC), Phospholipone 90H (Ph90H), soybean lipid (Syb) or a mixture of DSPC and DMPC (1:1). The average particle size and size distribution were determined using laser diffraction analysis. It was found that both EE and average particle size differ depending on both lipid and liposomal types. The in vitro release of glucose from different types of liposomes was performed using a dispersion method. It was found that the in vitro release of glucose from different liposomes is dependent on the lipid type. 18F-FDG was encapsulated in MLV 1,2-Dimyristoyl-sn-Glycero-3-Phosphocholine (DMPC), 1,2-Distearoyl-sn-Glycero-3-Phosphocholine (DSPC), Phospholipone 90H (Ph90H), soybean lipid (Syb) or a mixture of DSPC and DMPC (1:1). FDG-containing LUV and SUV were prepared using Ph90H lipid. The in vitro release of FDG from the different types of lipids was accomplished using a dispersion method. Results similar to that of glucose release were obtained. In vivo imaging of FDG in both uncapsulated FDG and FDG-containing MLV was performed in the brain and the whole body of rats using PET scanner. It was found that the release of FDG from FDG-containing MLV was sustained. In vitro-In vivo correlation was studied using the in vitro release data of FDG from liposomes and in vivo absorption data of FDG from injected liposomes using microPET. Erbium, which is a lanthanide metal, was used as a chelate with DTPA for encapsulation in SUV liposomes for the indirect radiation therapy of cancer. The liposomes were prepared using three different concentrations of soybean lipid (30, 50 and 70 mg/ml). The stability of Er-DTPA SUV liposomes was carried out by storage of the prepared liposomes at three different temperatures (4, 25 and 37 °C). It was found that the release of Er-DTPA complex is temperature dependent, the higher the temperature, the higher the release. There was an inverse relationship between the release of the Er-DTPA complex and the concentration of lipid.

Biodegradable systems for the development of functional materials

This PhD work was aimed to design, develop, and characterize gelatin-based scaffolds, for the repair of defects in the muscle-skeletal system. Gelatin is a biopolymer widely used for pharmaceutical and medical applications, thanks to its biodegradability and biocompatibility. It is obtained from collagen via thermal denaturation or chemical-physical degradation. Despite its high potential as biomaterial, gelatin exhibits poor mechanical properties and a low resistance in aqueous environment. Crosslinking treatment and enrichment with reinforcement materials are thus required for biomedical applications. In this work, gelatin based scaffolds were prepared following three different strategies: films were prepared through the solvent casting method, electrospinning technique was applied for the preparation of porous mats, and 3D porous scaffolds were prepared through freeze-drying. The results obtained on films put into evidence the influence of pH, crosslinking and reinforcement with montmorillonite (MMT), on the structure, stability and mechanical properties of gelatin and MMT/gelatin composites. The information acquired on the effect of crosslinking in different conditions was utilized to optimize the preparation procedure of electrospun and freeze-dried scaffolds. A successful method was developed to prepare gelatin nanofibrous scaffolds electrospun from acetic acid/water solution and stabilized with a non-toxic crosslinking agent, genipin, able to preserve their original morphology after exposure to water. Moreover, the co-electrospinning technique was used to prepare nanofibrous scaffolds at variable content of gelatin and polylactic acid. Preliminary in vitro tests indicated that the scaffolds are suitable for cartilage tissue engineering, and that their potential applications can be extended to cartilage-bone interface tissue engineering. Finally, 3D porous gelatin scaffolds, enriched with calcium phosphate, were prepared with the freeze-drying method. The results indicated that the crystallinity of the inorganic phase influences porosity, interconnectivity and mechanical properties. Preliminary in vitro tests show good osteoblast response in terms of proliferation and adhesion on all the scaffolds.

Amphiphile Kammpolymere von Poly(2,7-carbazol)

Die vorliegende Dissertation beschreibt die Verschmelzung der Konzepte von konjugierten Polyelektrolyten und amphiphilen Kammpolymeren in Form von konjugierten, Poly(2,7-carbazol)-basierenden Polyelektrolytkammpolymeren mit Poly(L-lysin)seitenketten sowie Alkyl- oder Polyethylenglykolsubstituenten. Die Synthese wurde durch die Suzuki-Polykondensation von monodispersen Makromonomeren erreicht. Hierbei fand die Precursor-Synthesestrategie Anwendung. In diesem Ansatz war die ε-Aminofunktion des Lysins mit einer Benzoyloxycarbonylschutzgruppe geschützt. Der Aufbau der benötigten monodispersen Makromonomere erfolgte durch die Kupplung von Poly(L-lysin)ketten an den Carbazolbaustein mittels eines aktivierten Esters. Eine Besonderheit der hergestellten Kammpolymere lag in den konformativen Eigenschaften seiner einzelnen Komponenten. Dabei konnte die Konformation der Poly(L-lysin)seitenketten infolge ihres Polyelektrolyt- und Peptidcharakters gezielt mit Hilfe des pH-Wertes und der Ionenstärke variiert werden, wohingegen das konjugierte Rückgrat seine steife Konformation beibehielt. Infolge des Polyelektrolytcharakters zeigte sich zudem, dass die Polymere in sauren und neutralen, wässrigen Lösungen zu großen Teilen in Form von Domänenstrukturen auftraten, während im Basischen eine sofortige Aggregation eintrat. Ein weiteres Merkmal der vorgestellten Polyelektrolytkammpolymere war ihr amphiphiler Charakter. Diese Amphiphilie der in dieser Arbeit vorgestellten Polyelektrolytkammpolymere beeinflusste dabei maßgeblich ihre unstrukturierte Anordnung in Lösung, in der festen Phase sowie an Oberflächen.

Quantum dot-dye hybrid systems for energy transfer applications

In this thesis, we focus on the preparation of energy transfer-based quantum dot (QD)-dye hybrid systems. Two kinds of QD-dye hybrid systems have been successfully synthesized: QD-silica-dye and QD-dye hybrid systems.rn rnIn the QD-silica-dye hybrid system, multishell CdSe/CdS/ZnS QDs were adsorbed onto monodisperse Stöber silica particles with an outer silica shell of thickness 2 - 24 nm containing organic dye molecules (Texas Red). The thickness of this dye layer has a strong effect on the total sensitized acceptor emission, which is explained by the increase in the number of dye molecules homogeneously distributed within the silica shell, in combination with an enhanced surface adsorption of QDs with increasing dye amount. Our conclusions were underlined by comparison of the experimental results with Monte-Carlo simulations, and by control experiments confirming attractive interactions between QDs and Texas Red freely dissolved in solution. rnrnNew QD-dye hybrid system consisting of multishell QDs and organic perylene dyes have been synthesized. We developed a versatile approach to assemble extraordinarily stable QD-dye hybrids, which uses dicarboxylate anchors to bind rylene dyes to QD. This system yields a good basis to study the energy transfer between QD and dye because of its simple and compact design: there is no third kind of molecule linking QD and dye; no spacer; and the affinity of the functional group to the QD surface is strong. The FRET signal was measured for these complexes as a function of both dye to QD ratio and center-to-center distance between QD and dye by controlling number of covered ZnS layers. Data showed that fluorescence resonance energy transfer (FRET) was the dominant mechanism of the energy transfer in our QD-dye hybrid system. FRET efficiency can be controlled by not only adjusting the number of dyes on the QD surface or the QD to dye distance, but also properly choosing different dye and QD components. Due to the strong stability, our QD-dye complexes can also be easily transferred into water. Our approach can apply to not only dye molecules but also other organic molecules. As an example, the QDs have been complexed with calixarene molecules and the QD-calixarene complexes also have potential for QD-based energy transfer study. rn

Structure property relations in complex copolymer systems

A thorough investigation was made of the structure-property relation of well-defined statistical, gradient and block copolymers of various compositions. Among the copolymers studied were those which were synthesized using isobornyl acrylate (IBA) and n-butyl acrylate (nBA) monomer units. The copolymers exhibited several unique properties that make them suitable materials for a range of applications. The thermomechanical properties of these new materials were compared to acrylate homopolymers. By the proper choice of the IBA/nBA monomer ratio, it was possible to tune the glass transition temperature of the statistical P(IBA-co-nBA) copolymers. The measured Tg’s of the copolymers with different IBA/nBA monomer ratios followed a trend that fitted well with the Fox equation prediction. While statistical copolymers showed a single glass transition (Tg between -50 and 90 ºC depending on composition), DSC block copolymers showed two Tg’s and the gradient copolymer showed a single, but very broad, glass transition. PMBL-PBA-PMBL triblock copolymers of different composition ratios were also studied and revealed a microphase separated morphology of mostly cylindrical PMBL domains hexagonally arranged in the PBA matrix. DMA studies confirmed the phase separated morphology of the copolymers. Tensile studies showed the linear PMBL-PBA-PMBL triblock copolymers having a relatively low elongation at break that was increased by replacing the PMBL hard blocks with the less brittle random PMBL-r-PMMA blocks. The 10- and 20-arm PBA-PMBL copolymers which were studied revealed even more unique properties. SAXS results showed a mixture of cylindrical PMBL domains hexagonally arranged in the PBA matrix, as well as lamellar. Despite PMBL’s brittleness, the triblock and multi-arm PBA-PMBL copolymers could become suitable materials for high temperature applications due to PMBL’s high glass transition temperature and high thermal stability. The structure-property relation of multi-arm star PBA-PMMA block copolymers was also investigated. Small-angle X-ray scattering revealed a phase separated morphology of cylindrical PMMA domains hexagonally arranged in the PBA matrix. DMA studies found that these materials possess typical elastomeric behavior in a broad range of service temperatures up to at least 250°C. The ultimate tensile strength and the elastic modulus of the 10- and 20-arm star PBA-PMMA block copolymers are significantly higher than those of their 3-arm or linear ABA type counterparts with similar composition, indicating a strong effect of the number of arms on the tensile properties. Siloxane-based copolymers were also studied and one of the main objectives here was to examine the possibility to synthesize trifluoropropyl-containing siloxane copolymers of gradient distribution of trifluoropropyl groups along the chain. DMA results of the PDMS-PMTFPS siloxane copolymers synthesized via simultaneous copolymerization showed that due to the large difference in reactivity rates of 2,4,6-tris(3,3,3-trifluoropropyl)-2,4,6-trimethylcyclotrisiloxane (F) and hexamethylcyclotrisiloxane (D), a copolymer of almost block structure containing only a narrow intermediate fragment with gradient distribution of the component units was obtained. A more dispersed distribution of the trifluoropropyl groups was obtained by the semi-batch copolymerization process, as the DMA results revealed more ‘‘pure gradient type’’ features for the siloxane copolymers which were synthesized by adding F at a controlled rate to the polymerization of the less reactive D. As with trifluoropropyl-containing siloxane copolymers, vinyl-containing polysiloxanes may be converted to a variety of useful polysiloxane materials by chemical modification. But much like the trifluoropropyl-containing siloxane copolymers, as a result of so much difference in the reactivities between the component units 2,4,6-trivinyl-2,4,6-trimethylcyclotrisiloxane (V) and hexamethylcyclotrisiloxane (D), thermal and mechanical properties of the PDMS-PMVS copolymers obtained by simultaneous copolymerization was similar to those of block copolymers. Only the copolymers obtained by semi-batch method showed properties typical for gradient copolymers.

Patterns in and kinetics of phase separation in binary mixtures

This work focused mainly on two aspects of kinetics of phase separation in binary mixtures. In the first part, we studied the interplay of hydrodynamics and the phase separation of binary mixtures. A considerably flat container (a laterally extended geometry), at an aspect ratio of 14:1 (diameter: height) was chosen, so that any hydrodynamic instabilities, if they arise, could be tracked. Two binary mixtures were studied. One was a mixture of methanol and hexane, doped with 5% ethanol, which phase separated under cooling. The second was a mixture of butoxyethanol and water, doped with 2% decane, which phase separated under heating. The dopants were added to bring down the phase transition temperature around room temperature.rnrnAlthough much work has been done already on classical hydrodynamic instabilities, not much has been done in the understanding of the coupling between phase separation and hydrodynamic instabilities. This work aimed at understanding the influence of phase separation in initiating any hydrodynamic instability, and also vice versa. Another aim was to understand the influence of the applied temperature protocol on the emergence of patterns characteristic to hydrodynamic instabilities. rnrnOn slowly cooling the system continuously, at specific cooling rates, patterns were observed in the first mixture, at the start of phase separation. They resembled the patterns observed in classical Rayleigh-Bénard instability, which arises when a liquid continuously is heated from below. To suppress this classical convection, the cooling setup was tuned such that the lower side of the sample always remained cooler by a few millikelvins, relative to the top. We found that the nature of patterns changed with different cooling rates, with stable patterns appearing for a specific cooling rate (1K/h). On the basis of the cooling protocol, we estimated a modified Rayleigh number for our system. We found that the estimated modified Rayleigh number is near the critical value for instability, for cooling rates between 0.5K/h and 1K/h. This is consistent with our experimental findings. rnrnThe origin of the patterns, in spite of the lower side being relatively colder with respect to the top, points to two possible reasons. 1) During phase separation droplets of either phases are formed, which releases a latent heat. Our microcalorimetry measurements show that the rise in temperature during the first phase separation is in the order of 10-20millikelvins, which in some cases is enough to reverse the applied temperature bias. Thus phase separation in itself initiates a hydrodynamic instability. 2) The second reason comes from the cooling protocol itself. The sample was cooled from above and below. At sufficiently high cooling rates, there are situations where the interior of the sample is relatively hotter than both top and bottom of the sample. This is sufficient to create an instability within the cell. Our experiments at higher cooling rates (5K/h and above) show complex patterns, which hints that there is enough convection even before phase separation occurs. Infact, theoretical work done by Dr.Hayase show that patterns could arise in a system without latent heat, with symmetrical cooling from top and bottom. The simulations also show that the patterns do not span the entire height of the sample cell. This is again consistent with the cell sizes measured in our experiment.rnrnThe second mixture also showed patterns at specific heating rates, when it was continuously heated inducing phase separation. In this case though, the sample was turbid for a long time until patterns appeared. A meniscus was most probably formed before the patterns emerged. We attribute the reason of patterns in this case to Marangoni convection, which is present in systems with an interface, where local differences in surface tension give rise to an instability. Our estimates for the Rayleigh number also show a significantly lower number than that's required for RB-type instability.rnrnIn the first part of the work, therefore, we identify two different kinds of hydrodynamic instabilities in two different mixtures. Both are observed during, or after the first phase separation. Our patterns compare with the classical convection patterns, but here the origins are from phase separation and the cooling protocol.rnrnIn the second part of the work, we focused on the kinetics of phase separation in a polymer solution (polystyrene and methylcyclohexane), which is cooled continuously far down into the two phase region. Oscillations in turbidity, denoting material exchange between the phases are seen. Three processes contribute to the phase separation: Nucleation of droplets, their growth and coalescence, and their subsequent sedimentation. Experiments in low molecular binary mixtures had led to models of oscillation [43] which considered sedimentation time scales much faster than the time scales of nucleation and growth. The size and shape of the sample therefore did not matter in such situations. The oscillations in turbidity were volume-dominated. The present work aimed at understanding the influence of sedimentation time scales for polymer mixtures. Three heights of the sample with same composition were studied side by side. We found that periods increased with the sample height, thus showing that sedimentation time determines the period of oscillations in the polymer solutions. We experimented with different cooling rates and different compositions of the mixture, and we found that periods are still determined by the sample height, and therefore by sedimentation time. rnrnWe also see that turbidity emerges in two ways; either from the interface, or throughout the sample. We suggest that oscillations starting from the interface are due to satellite droplets that are formed on droplet coalescence at the interface. These satellite droplets are then advected to the top of the sample, and they grow, coalesce and sediment. This type of an oscillation wouldn't require the system to pass the energy barrier required for homogenous nucleation throughout the sample. This mechanism would work best in sample where the droplets could be effectively advected throughout the sample. In our experiments, we see more interface dominated oscillations in the smaller cells and lower cooling rates, where droplet advection is favourable. In larger samples and higher cooling rates, we mostly see that the whole sample becomes turbid homogenously, which requires the system to pass the energy barrier for homogenous nucleation.rnrnOscillations, in principle, occur since the system needs to pass an energy barrier for nucleation. The height of the barrier decreases with increasing supersaturation, which in turn is from the temperature ramp applied. This gives rise to a period where the system is clear, in between the turbid periods. At certain specific cooling rates, the system can follow a path such that the start of a turbid period coincides with the vanishing of the last turbid period, thus eliminating the clear periods. This means suppressions of oscillations altogether. In fact we experimentally present a case where, at a certain cooling rate, oscillations indeed vanish. rnrnThus we find through this work that the kinetics of phase separation in polymer solution is different from that of a low molecular system; sedimentation time scales become relevant, and therefore so does the shape and size of the sample. The role of interface in initiating turbid periods also become much more prominent in this system compared to that in low molecular mixtures.rnrnIn summary, some fundamental properties in the kinetics of phase separation in binary mixtures were studied. While the first part of the work described the close interplay of the first phase separation with hydrodynamic instabilities, the second part investigated the nature and determining factors of oscillations, when the system was cooled deep into the two phase region. Both cases show how the geometry of the cell can affect the kinetics of phase separation. This study leads to further fundamental understandings of the factors contributing to the kinetics of phase separation, and to the understandings of what can be controlled and tuned in practical cases. rn

Electron spectroscopy of novel charge transfer systems based on polycyclic aromatic hydrocarbons

Organische Ladungstransfersysteme weisen eine Vielfalt von konkurrierenden Wechselwirkungen zwischen Ladungs-, Spin- und Gitterfreiheitsgraden auf. Dies führt zu interessanten physikalischen Eigenschaften, wie metallische Leitfähigkeit, Supraleitung und Magnetismus. Diese Dissertation beschäftigt sich mit der elektronischen Struktur von organischen Ladungstransfersalzen aus drei Material-Familien. Dabei kamen unterschiedliche Photoemissions- und Röntgenspektroskopietechniken zum Einsatz. Die untersuchten Moleküle wurden z.T. im MPI für Polymerforschung synthetisiert. Sie stammen aus der Familie der Coronene (Donor Hexamethoxycoronen HMC und Akzeptor Coronen-hexaon COHON) und Pyrene (Donor Tetra- und Hexamethoxypyren TMP und HMP) im Komplex mit dem klassischen starken Akzeptor Tetracyanoquinodimethan (TCNQ). Als dritte Familie wurden Ladungstransfersalze der k-(BEDT-TTF)2X Familie (X ist ein monovalentes Anion) untersucht. Diese Materialien liegen nahe bei einem Bandbreite-kontrollierten Mottübergang im Phasendiagramm.rnFür Untersuchungen mittels Ultraviolett-Photoelektronenspektroskopie (UPS) wurden UHV-deponierte dünne Filme erzeugt. Dabei kam ein neuer Doppelverdampfer zum Einsatz, welcher speziell für Milligramm-Materialmengen entwickelt wurde. Diese Methode wies im Ladungstransferkomplex im Vergleich mit der reinen Donor- und Akzeptorspezies energetische Verschiebungen von Valenzzuständen im Bereich weniger 100meV nach. Ein wichtiger Aspekt der UPS-Messungen lag im direkten Vergleich mit ab-initio Rechnungen.rnDas Problem der unvermeidbaren Oberflächenverunreinigungen von lösungsgezüchteten 3D-Kristallen wurde durch die Methode Hard-X-ray Photoelectron Spectroscopy (HAXPES) bei Photonenenergien um 6 keV (am Elektronenspeicherring PETRA III in Hamburg) überwunden. Die große mittlere freie Weglänge der Photoelektronen im Bereich von 15 nm resultiert in echter Volumensensitivität. Die ersten HAXPES Experimente an Ladungstransferkomplexen weltweit zeigten große chemische Verschiebungen (mehrere eV). In der Verbindung HMPx-TCNQy ist die N1s-Linie ein Fingerabdruck der Cyanogruppe im TCNQ und zeigt eine Aufspaltung und einen Shift zu höheren Bindungsenergien von bis zu 6 eV mit zunehmendem HMP-Gehalt. Umgekehrt ist die O1s-Linie ein Fingerabdruck der Methoxygruppe in HMP und zeigt eine markante Aufspaltung und eine Verschiebung zu geringeren Bindungsenergien (bis zu etwa 2,5eV chemischer Verschiebung), d.h. eine Größenordnung größer als die im Valenzbereich.rnAls weitere synchrotronstrahlungsbasierte Technik wurde Near-Edge-X-ray-Absorption Fine Structure (NEXAFS) Spektroskopie am Speicherring ANKA Karlsruhe intensiv genutzt. Die mittlere freie Weglänge der niederenergetischen Sekundärelektronen (um 5 nm). Starke Intensitätsvariationen von bestimmten Vorkanten-Resonanzen (als Signatur der unbesetzte Zustandsdichte) zeigen unmittelbar die Änderung der Besetzungszahlen der beteiligten Orbitale in der unmittelbaren Umgebung des angeregten Atoms. Damit war es möglich, präzise die Beteiligung spezifischer Orbitale im Ladungstransfermechanismus nachzuweisen. Im genannten Komplex wird Ladung von den Methoxy-Orbitalen 2e(Pi*) und 6a1(σ*) zu den Cyano-Orbitalen b3g und au(Pi*) und – in geringerem Maße – zum b1g und b2u(σ*) der Cyanogruppe transferiert. Zusätzlich treten kleine energetische Shifts mit unterschiedlichem Vorzeichen für die Donor- und Akzeptor-Resonanzen auf, vergleichbar mit den in UPS beobachteten Shifts.rn

Evolution of the structural and fracture design of the ISS payloads due to the new launchers, specifically applied to Biolab IEC-2 projects

The relatively young discipline of astronautics represents one of the scientifically most fascinating and technologically advanced achievements of our time. The human exploration in space does not offer only extraordinary research possibilities but also demands high requirements from man and technology. The space environment provides a lot of attractive experimental tools towards the understanding of fundamental mechanism in natural sciences. It has been shown that especially reduced gravity and elevated radiation, two distinctive factors in space, influence the behavior of biological systems significantly. For this reason one of the key objectives on board of an earth orbiting laboratory is the research in the field of life sciences, covering the broad range from botany, human physiology and crew health up to biotechnology. The Columbus Module is the only European low gravity platform that allows researchers to perform ambitious experiments in a continuous time frame up to several months. Biolab is part of the initial outfitting of the Columbus Laboratory; it is a multi-user facility supporting research in the field of biology, e.g. effect of microgravity and space radiation on cell cultures, micro-organisms, small plants and small invertebrates. The Biolab IEC are projects designed to work in the automatic part of Biolab. In this moment in the TO-53 department of Airbus Defence & Space (formerly Astrium) there are two experiments that are in phase C/D of the development and they are the subject of this thesis: CELLRAD and CYTOSKELETON. They will be launched in soft configuration, that means packed inside a block of foam that has the task to reduce the launch loads on the payload. Until 10 years ago the payloads which were launched in soft configuration were supposed to be structural safe by themselves and a specific structural analysis could be waived on them; with the opening of the launchers market to private companies (that are not under the direct control of the international space agencies), the requirements on the verifications of payloads are changed and they have become much more conservative. In 2012 a new random environment has been introduced due to the new Space-X launch specification that results to be particularly challenging for the soft launched payloads. The last ESA specification requires to perform structural analysis on the payload for combined loads (random vibration, quasi-steady acceleration and pressure). The aim of this thesis is to create FEM models able to reproduce the launch configuration and to verify that all the margins of safety are positive and to show how they change because of the new Space-X random environment. In case the results are negative, improved design solution are implemented. Based on the FEM result a study of the joins has been carried out and, when needed, a crack growth analysis has been performed.

Using sulfur isotope fractionation to understand the atmospheric oxidation of SO 2

Sulfate aerosol plays an important but uncertain role in cloud formation and radiative forcing of the climate, and is also important for acid deposition and human health. The oxidation of SO2 to sulfate is a key reaction in determining the impact of sulfate in the environment through its effect on aerosol size distribution and composition. This thesis presents a laboratory investigation of sulfur isotope fractionation during SO2 oxidation by the most important gas-phase and heterogeneous pathways occurring in the atmosphere. The fractionation factors are then used to examine the role of sulfate formation in cloud processing of aerosol particles during the HCCT campaign in Thuringia, central Germany. The fractionation factor for the oxidation of SO2 by ·OH radicals was measured by reacting SO2 gas, with a known initial isotopic composition, with ·OH radicals generated from the photolysis of water at -25, 0, 19 and 40°C (Chapter 2). The product sulfate and the residual SO2 were collected as BaSO4 and the sulfur isotopic compositions measured with the Cameca NanoSIMS 50. The measured fractionation factor for 34S/32S during gas phase oxidation is αOH = (1.0089 ± 0.0007) − ((4 ± 5) × 10−5 )T (°C). Fractionation during oxidation by major aqueous pathways was measured by bubbling the SO2 gas through a solution of H2 O2

Geological and hydrogeological features affecting migration, multi-phase partitioning and degradation of chlorinated hydrocarbons through unconsolidated porous media.

Chlorinated solvents are the most ubiquitous organic contaminants found in groundwater since the last five decades. They generally reach groundwater as Dense Non-Aqueous Phase Liquid (DNAPL). This phase can migrate through aquifers, and also through aquitards, in ways that aqueous contaminants cannot. The complex phase partitioning to which chlorinated solvent DNAPLs can undergo (i.e. to the dissolved, vapor or sorbed phase), as well as their transformations (e.g. degradation), depend on the physico-chemical properties of the contaminants themselves and on features of the hydrogeological system. The main goal of the thesis is to provide new knowledge for the future investigations of sites contaminated by DNAPLs in alluvial settings, proposing innovative investigative approaches and emphasizing some of the key issues and main criticalities of this kind of contaminants in such a setting. To achieve this goal, the hydrogeologic setting below the city of Ferrara (Po plain, northern Italy), which is affected by scattered contamination by chlorinated solvents, has been investigated at different scales (regional and site specific), both from an intrinsic (i.e. groundwater flow systems) and specific (i.e. chlorinated solvent DNAPL behavior) point of view. Detailed investigations were carried out in particular in one selected test-site, known as “Caretti site”, where high-resolution vertical profiling of different kind of data were collected by means of multilevel monitoring systems and other innovative sampling and analytical techniques. This allowed to achieve a deep geological and hydrogeological knowledge of the system and to reconstruct in detail the architecture of contaminants in relationship to the features of the hosting porous medium. The results achieved in this thesis are useful not only at local scale, e.g. employable to interpret the origin of contamination in other sites of the Ferrara area, but also at global scale, in order to address future remediation and protection actions of similar hydrogeologic settings.

Einfluss verschiedener nanopartikulärer Systeme auf die zelluläre Aufnahme und Zytotoxizität

Die vorliegende Dissertation untersucht Nanopartikel und Nanokapseln aus verschiedenen Materialien mit verschiedenen Modifikationen für einen zielgerichteten Medikamententransport (Drug Targeting). Obwohl bisher zahlreiche Nanopartikel und -kapseln synthetisiert wurden, besteht nach wie vor hinsichtlich der zellulären Verträglichkeit, Biokompatibilität und Aufnahme kein allumfassendes Verständnis. Mit Hilfe der in dieser Arbeit vorgestellten Untersuchungen und Ergebnissen soll ein Beitrag zur Schließung dieser Lücke geleistet werden.rnIm Rahmen der vorliegenden Dissertation wurde der Einfluss der Herstellungsmaterialien PS, PLLA, PMMA, Biomakromoleküle (BSA, DNA), ggf. stabilisiert durch HPMA-LMA-Copolymere und neu-synthetisierte Surfmere, der Formmodifikationen Streckung und Kristallisierung, der Oberflächenmodifikationen mittels verschiedener Tenside und PEG auf die zelluläre Aufnahme und Verträglichkeit hin untersucht.rnZusammenfassend lässt sich die Aussage treffen, dass zahlreiche Materialien zur Herstellung von Trägersystemen geeignet sind und sich als biokompatibel und nicht-zytotoxisch erwiesen haben, sich jedoch stark hinsichtlich der Aufnahmeeffizienz in verschiedene Zelllinien unterscheiden. rnIm ersten Abschnitt (Kapitel 5.1) wurden in der ersten und zweiten Untersuchung auf allgemeine Parameter, die die Aufnahme von Nanopartikeln beeinflussen, eingegangen. Hier wurde der Einfluss des Alters von PLLA-Partikeln auf die zelluläre Aufnahme und Toxizität untersucht. Es konnte gezeigt werden, dass mit zunehmender Materialalterung die zelluläre Aufnahme abnimmt. Eine Zytotoxizität konnte nicht gezeigt werden.rnWeiterhin wurde der Einfluss des FCS-Gehalts des Zell-Mediums auf die zelluläre Aufnahme von PMMA-Partikeln untersucht. Es konnte gezeigt werden, dass mit einer steigenden FCS-Konzentration eine Abnahme der zellulären Aufnahme von PMMA-Partikeln einhergeht. Die höchste zelluläre Aufnahme konnte bei einem FCS-Gehalt des Zellmediums von 0,05% verzeichnet werden. rnIm zweiten Abschnitt (Kapitel 5.2) wurde die Stabilisierung von Nanopartikeln mittels neusynthetisierter Tenside und deren Einfluss auf die Zelle-Nanopartikel-Interaktionen untersucht. Dazu wurde zum einen die Oberflächenfunktionalisierung von Nanopartikeln mit Hilfe neu-synthetisierter „Surfmere“ und deren Einfluss auf die zelluläre Aufnahme und Toxizität untersucht. Die hergestellten Surfmere bewirken gleichzeitig eine Stabilisierung und Funktionalisierung der Nanopartikeloberfläche mit Phosphonatgruppen. Hier wurden kovalente „Surfmer“ stabilisierte Nanopartikel mit Tensid- (SDP) stabilisierten Nanopartikeln verglichen. Zudem wurden dialysierte Nanopartikel mit nicht-dialysierten verglichen. Bezüglich der zellulären Aufnahme konnte für die mittels Dialyse gereinigten Nanopartikel eine gute Aufnahme ohne Unterschiede zwischen den kovalent und nicht-kovalent Phosphonat-funktionalisierten Partikeln beobachtet werden. Die ungereinigten, SDP-stabilisierte, nicht-kovalent gebundene Nanopartikel zeigten hingegen eine bis zu 30% stärkere Aufnahme in die HeLa-Zellen und hMSCs.rnWeiterhin der Einsatz von mit HPMA-LMA-Copolymeren stabilisierte Polystyrol- und PLLA-Partikel, die den Einsatz von Tensiden während des Miniemulsionsprozesses überflüssig machen, untersucht. Auch hier konnte keine Zytotoxizität nachgewiesen werden. Die Aufnahme in HeLa-Zellen scheint mehr von der Größe der Nanopartikel als vom verwendeten Material und in hMSCs mehr von den Oberflächeneigenschaften der Nanopartikel abzuhängen.rnIm dritten Abschnitt (Kapitel 5.3) wird auf die Möglichkeit der Formmodifikation von Polystyrol-Partikeln und deren Einfluss auf die Nanopartikel-Zelle-Interaktionen eingegangen. Es geht dabei um die Aufnahme und Zytotoxizität von verstreckten (elongierten) Polystyrol-Partikeln im Vergleich zu sphärischen Nanopartikeln, sowie die Aufnahme und Zytotoxizität von kristallinen Polystyrol-Partikeln in verschiedene Zelllinien. Bei den verstreckten Partikeln nimmt die Aufnahme-Effizienz in HeLa-Zellen und hMSCs mit zunehmender Verstreckung ab. Eine Zytotoxizität konnte für keinen der erwähnten Nanopartikel nachgewiesen werden. Bei den Polystyrol-Partikeln unterschiedlicher Taktizität zeigen die kristallierten Polystyrol-Partikel eine geringfügig besser Aufnahme-Rate als die nicht-kristallierten Polystyrol-Partikel. Dabei zeigen die nach dem Herstellungsprozess mittels der Lösemittelverdampfungstechnik der wässrigen Phase entnommenen Partikel eine bessere Aufnahme als die nach der Verdampfung des Chloroforms verfügbaren Partikel. Insgesamt konnte jedoch für alle Polystyrol-Partikel trotz der unterschiedlichen Taktizitäten nach der Aufnahme in HeLa-Zellen und hMSCs mittels Durchflusszytometrie hohe Fluoreszenz-Intensitäten verzeichnet werden. Setzt man hohe Fluoreszenz-Intensitäten bei in Zellen aufgenommenen Partikeln mit guten Aufnahmeraten gleich, sind die hier dargestellten Aufnahmeraten als sehr gut zu bezeichnen. rnAuf Nanosysteme mit einer reduzierten zellulären Aufnahme wird im letzten Abschnitt (Kapitel 5.4) eingegangen. Dabei wird zum einen die unterschiedliche Oberflächenmodifikation von Polystyrol-Partikeln mit dem Co-Monomer PEG-MA und den Tensiden SDS und Lutensol AT50 untersucht. Von PEG-MA wurden zudem verschiedene Molekulargewichte (Mn=300 g•mol-1 und Mn=2080 g•mol-1) und verschiedene Konzentrationen (1,5%, 5%, 10%) eingesetzt. Ein Teil der Partikel wurde mit SDS und der andere Teil mit Lutensol AT50 hergestellt. In einem weiteren Schritt wurde das jeweilig gegenteilige Tensid (statt SDS Lutensol AT50 und umgekehrt) eingesetzt, um zu überprüfen, ob sich der zuvor beobachtete Effekt umkehren lässt. Anschließend wurde ein erst mit SDS stabilisierter Nanopartikel (BR01) mit verschiedenen Lutensol AT50-Anteilen (5%, 10%, 25%, 50%, 100%) redispergiert. Die effizienteste Aufnahme zeigte der unmodifizierte, mit SDS stabilisierte Nanopartikel BR01, die niedrigste der ebenfalls unmodifizierte, mit Lutensol AT50 stabilisierte Nanopartikel BR02. Eine steigende Konzentration des PEG-MA Mn=300 g•mol-1 hemmt die Aufnahme von mit SDS stabilisierten Partikeln konstant. Für PEG-MA Mn=2080 g•mol-1 konnte hingegen kein Einfluss nachgewiesen werden. Für die mit Lutensol AT50 stabilisierten Partikel konnte kein Einfluss von PEG-MA nachgewiesen werden. Daraus resultiert, dass der Einsatz von physikalisch adsorbiertem Lutensol AT50 die zelluläre Aufnahme effektiver hemmt als der Einsatz von kovalent gebundenem PEG-MA unterschiedlicher Kettenlänge.rnDer Einsatz von mit Biomakromolekülen hergestellten Nanokapseln, die mit zwei verschiedenen Tensiden (SDS und Lutensol AT50) stabilisiert wurden, wurde im Weiteren näher untersucht. Bei den mit SDS stabilisierten Kapseln erwiesen sich die mit ssDNA hergestellten Kapseln BN-54 und BN-55 als leicht toxisch für die HeLa-Zellen. Dagegen sind alle eingesetzten, mit Lutensol AT50 redispergierten Nanokapseln sowohl für HeLa-Zellen als auch für hMSCs zytotoxisch. Hier ist die toxische Wirkung auf das nicht-ionische Tensid Lutensol AT50 zurückzuführen. Eine zelluläre Aufnahme konnte für keine mit Biomakromolekülen hergestellten Nanokapsel nachgewiesen werden.rnDen Abschluss der Untersuchungen bildet die vergleichende Analyse der in dieser Arbeit mit dem Fluoreszenzfarbstoff PMI versehenen Partikeln hinsichtlich deren Aufnahme in HeLa-Zellen und hMSCs und deren zytotoxische Auswirkungen. In der vergleichenden Analyse werden die zuvor vorgestellten Ergebnisse für PMI-Partikeln nochmal im Kontext betrachtet. Dabei erwies sich sowohl für die HeLa-Zellen als auch für die hMSCs, dass die meisten Partikel eine geringe bis keine zelluläre Aufnahme zeigen. Eine gute Aufnahme konnte nur für wenige Nanopartikel (vor allem für die kristallinen Nanopartikel) verzeichnet werden. Eine Korrelation zwischen der Aufnahmeeffizienz und der Zytotoxizität konnte nicht nachgewiesen werden. rn