Depositional conditions on an alluvial fan at the turn of the Weichselian to the Holocene – a case study in the Żmigród Basin, southwest Poland

Presented are the results of research into the fluvio-aeolian sedimentary succession at the site of Postolin in the Żmigród Basin, southwest Poland. Based on lithofacies analysis, textural analysis, Thermoluminescence and Infrared-Optical Stimulated Luminescence dating and GIS analysis, three lithofacies units were recognised and their stratigraphic suc- cession identified: 1) the lower unit was deposited during the Pleni-Weichselian within a sand-bed braided river fun- ctioning under permafrost conditions within the central part of the alluvial fan; 2) the middle unit is the result of aeolian deposition and fluvial redeposition on the surface of the fan during long-term permafrost and progressive decrease of humidity of the climate at the turn of the Pleni- to the Late Weichselian; 3) the upper unit accumulated following the development of longitudinal dunes at the turn of the Late Weichselian to the Holocene; the development of dunes was interrupted twice by the form being stabilised by vegetation and soil development.

Highly polymorphic microsatellite markers for the Mediterranean endemic fan mussel Pinna nobilis

Pinna nobilis is an endemic bivalve of the Mediterranean Sea whose populations have decreased in the last decades due to human pressure; as a consequence, it was declared a protected species in 1992. Despite its conservation status, few genetic studies using mitochondrial markers have been published. We report on the isolation and development of 10 microsatellite loci for the fan mussel, Pinna nobilis. All loci (2 di-nucleotide, 5 tri-nucleotide, 2 tetra-nucleotide and 1 penta-nucleotide) are characterized by high levels of polymorphism in 76 individuals tested from two populations in the Balearic Islands (Spain, Western Mediterranean Sea). The number of alleles ranged from 4 to 24 and expected heterozygosity ranged from 0.4269 to 0.9400. These microsatellites could be very useful for the assessment of the genetic diversity and connectivity patterns of P. nobilis and the establishment of new conservation strategies.

Active oxygen by Ce–Pr mixed oxide nanoparticles outperform diesel soot combustion Pt catalysts

A Ce0.5Pr0.5O2 mixed oxide has been prepared with the highest surface area and smallest particle size ever reported (125 m2/g and 7 nm, respectively), also being the most active diesel soot combustion catalyst ever tested under realistic conditions if catalysts forming highly volatile species are ruled out. This Ce–Pr mixed oxide is even more active than a reference platinum-based commercial catalyst. This study provides an example of the efficient participation of oxygen species released by a ceria catalyst in a heterogeneous catalysis reaction where both the catalyst and one of the reactants (soot) are solids. It has been concluded that both the ceria-based catalyst composition (nature and amount of dopant) and the particle size play key roles in the combustion of soot through the active oxygen-based mechanism. The composition determines the production of active oxygen and the particle size the transfer of such active oxygen species from catalyst to soot.

Avaliação térmica dos resíduos da destilação atmosférica das blendas - biodiesel/diesel

The worldwide concern regarding the use of sustainable energy and preserving the environment are determining factors in the search for resources and alternative sources of energy and therefore fuel less aggressive nature. In response to these difficulties Biodiesel has emerged as a good solution because it is produced from renewable sources, produces burns cleaner and is easily reproducible. This work was synthesized with biodiesel oil, sunflower via homogeneous catalysis in the presence of KOH, with and without the use of BHT and subsequently added to the blends BX (a proportion of biodiesel X = 5, 10, 15 and 20 %). Atmospheric distillation of the analysis, performed in blends with and without BHT were collected residue generated by each sample and performed a study heat from the thermogravimetric analysis at a heating rate of 10 °C*min-1, nitrogen atmosphere and heating to 600 °C. According to the specifications of Resolution N 7/2008 for biodiesel, it was found that the synthesized material was in accordance with the specifications. For blends showed that the samples are in accordance with the Resolution of ANP N 42/2009. From the TG / DTG curves of the samples of biodiesel, blends and waste can be seen that these show a single loss of thermal decomposition concerning constituents present in each sample. The blends without BHT with ratios of 5%, 10% and 15% biodiesel showed a lower amount of waste (1,07%; 1,09% e 1,10%) to mineral diesel (1,15%). Therefore, it is concluded that the addition of biodiesel with diesel mineral can improve some physico-chemical parameters, but also, depending on the added amount, decreasing the amount of waste generated. This fact is of great importance because the carbonaceous residue can cause problems in mechanical equipment and parts for vehicles, causing more frequent maintenance, and this is not desirable

Estudo térmico dos resíduos gerados da destilação atmosférica das misturas diesel/biodiesel de dendê

The growing world demand for energy supplied by fossil fuels, a major contributor to the emission of pollutants into the atmosphere and causing environmental problems, has been encouraging governments and international organizations to reflect and encourage the use of alternative renewable sources. Among these new possibilities deserves attention biodiesel, fuel cleaner and easy to reproduce. The study of new technologies involving that source is necessary. From this context, the paper aims at analyzing the thermal stability by thermogravimetric analysis, of the waste generated from atmospheric distillation of mixtures with ratios of 5, 10, 15 and 20% palm biodiesel in diesel with and without addition of BHT antioxidant. It was synthesized biodiesel through palm oil, via homogeneous catalysis in the presence of KOH, with and without the use of BHT and subsequently added to the diesel common indoor type (S1800) from a gas station BR. The diesel was already added with 5% biodiesel, and thus the proportions used for these blends were subtracted from the existing ratio in diesel fuel, resulting in the following proportions palm oil biodiesel: 0% (B5), 5% (B10), 10 % (B15) and 15% (B20). From atmospheric distillation analysis, performed in mixtures with and without BHT were collected residue generated by each sample and performed a thermal study from the thermogravimetric analysis at a heating rate of 10 °C.min-1, nitrogen atmosphere and heating to 600 ° C. According to the specifications of Resolution No. 7/2008 for biodiesel, it was found that the material was synthesized in accordance with the specifications. For mixtures, it was noted that the samples were in accordance with the ANP Resolution No. 42/2009. Given the TG / DTG curves of the samples of waste mixtures with and without BHT antioxidant was able to observe that they showed a single stage of thermal decomposition attributed to decomposition of heavy hydrocarbons and esters and other heavier constituents of the waste sample weighed. The thermal behavior of residues from atmospheric distillation of mixtures of diesel / biodiesel is very important to understand how this affects the proper functioning of the engine. A large amount of waste can generate a high content of particulate material, coke formation and carbonaceous deposits in engine valves, compromising their performance

Development of a 1-D Catalyzed Diesel Particulate Filter Model for Simulation of the Performance and the Oxidation of Particulate Matter and Nitrogen Oxides Using Passive Oxidation and Active Regeneration Engine Experimental Data

Back-pressure on a diesel engine equipped with an aftertreatment system is a function of the pressure drop across the individual components of the aftertreatment system, typically, a diesel oxidation catalyst (DOC), catalyzed particulate filter (CPF) and selective catalytic reduction (SCR) catalyst. Pressure drop across the CPF is a function of the mass flow rate and the temperature of the exhaust flowing through it as well as the mass of particulate matter (PM) retained in the substrate wall and the cake layer that forms on the substrate wall. Therefore, in order to control the back-pressure on the engine at low levels and to minimize the fuel consumption, it is important to control the PM mass retained in the CPF. Chemical reactions involving the oxidation of PM under passive oxidation and active regeneration conditions can be utilized with computer numerical models in the engine control unit (ECU) to control the pressure drop across the CPF. Hence, understanding and predicting the filtration and oxidation of PM in the CPF and the effect of these processes on the pressure drop across the CPF are necessary for developing control strategies for the aftertreatment system to reduce back-pressure on the engine and in turn fuel consumption particularly from active regeneration. Numerical modeling of CPF's has been proven to reduce development time and the cost of aftertreatment systems used in production as well as to facilitate understanding of the internal processes occurring during different operating conditions that the particulate filter is subjected to. A numerical model of the CPF was developed in this research work which was calibrated to data from passive oxidation and active regeneration experiments in order to determine the kinetic parameters for oxidation of PM and nitrogen oxides along with the model filtration parameters. The research results include the comparison between the model and the experimental data for pressure drop, PM mass retained, filtration efficiencies, CPF outlet gas temperatures and species (NO2) concentrations out of the CPF. Comparisons of PM oxidation reaction rates obtained from the model calibration to the data from the experiments for ULSD, 10 and 20% biodiesel-blended fuels are presented.

MODELING OF TRANSFER PATH FOR DETERMINATION OF COMBUSTION AND NOISE METRICS ON DIESEL ENGINES

Determination of combustion metrics for a diesel engine has the potential of providing feedback for closed-loop combustion phasing control to meet current and upcoming emission and fuel consumption regulations. This thesis focused on the estimation of combustion metrics including start of combustion (SOC), crank angle location of 50% cumulative heat release (CA50), peak pressure crank angle location (PPCL), and peak pressure amplitude (PPA), peak apparent heat release rate crank angle location (PACL), mean absolute pressure error (MAPE), and peak apparent heat release rate amplitude (PAA). In-cylinder pressure has been used in the laboratory as the primary mechanism for characterization of combustion rates and more recently in-cylinder pressure has been used in series production vehicles for feedback control. However, the intrusive measurement with the in-cylinder pressure sensor is expensive and requires special mounting process and engine structure modification. As an alternative method, this work investigated block mounted accelerometers to estimate combustion metrics in a 9L I6 diesel engine. So the transfer path between the accelerometer signal and the in-cylinder pressure signal needs to be modeled. Depending on the transfer path, the in-cylinder pressure signal and the combustion metrics can be accurately estimated - recovered from accelerometer signals. The method and applicability for determining the transfer path is critical in utilizing an accelerometer(s) for feedback. Single-input single-output (SISO) frequency response function (FRF) is the most common transfer path model; however, it is shown here to have low robustness for varying engine operating conditions. This thesis examines mechanisms to improve the robustness of FRF for combustion metrics estimation. First, an adaptation process based on the particle swarm optimization algorithm was developed and added to the single-input single-output model. Second, a multiple-input single-output (MISO) FRF model coupled with principal component analysis and an offset compensation process was investigated and applied. Improvement of the FRF robustness was achieved based on these two approaches. Furthermore a neural network as a nonlinear model of the transfer path between the accelerometer signal and the apparent heat release rate was also investigated. Transfer path between the acoustical emissions and the in-cylinder pressure signal was also investigated in this dissertation on a high pressure common rail (HPCR) 1.9L TDI diesel engine. The acoustical emissions are an important factor in the powertrain development process. In this part of the research a transfer path was developed between the two and then used to predict the engine noise level with the measured in-cylinder pressure as the input. Three methods for transfer path modeling were applied and the method based on the cepstral smoothing technique led to the most accurate results with averaged estimation errors of 2 dBA and a root mean square error of 1.5dBA. Finally, a linear model for engine noise level estimation was proposed with the in-cylinder pressure signal and the engine speed as components.

DYNAMIC MODEL BASED STATE ESTIMATION IN A HEAVY DUTY DIESEL AFTERTREATMENT SYSTEM FOR ONBOARD DIAGNOSTICS AND CONTROLS

Estimating un-measurable states is an important component for onboard diagnostics (OBD) and control strategy development in diesel exhaust aftertreatment systems. This research focuses on the development of an Extended Kalman Filter (EKF) based state estimator for two of the main components in a diesel engine aftertreatment system: the Diesel Oxidation Catalyst (DOC) and the Selective Catalytic Reduction (SCR) catalyst. One of the key areas of interest is the performance of these estimators when the catalyzed particulate filter (CPF) is being actively regenerated. In this study, model reduction techniques were developed and used to develop reduced order models from the 1D models used to simulate the DOC and SCR. As a result of order reduction, the number of states in the estimator is reduced from 12 to 1 per element for the DOC and 12 to 2 per element for the SCR. The reduced order models were simulated on the experimental data and compared to the high fidelity model and the experimental data. The results show that the effect of eliminating the heat transfer and mass transfer coefficients are not significant on the performance of the reduced order models. This is shown by an insignificant change in the kinetic parameters between the reduced order and 1D model for simulating the experimental data. An EKF based estimator to estimate the internal states of the DOC and SCR was developed. The DOC and SCR estimators were simulated on the experimental data to show that the estimator provides improved estimation of states compared to a reduced order model. The results showed that using the temperature measurement at the DOC outlet improved the estimates of the CO , NO , NO2 and HC concentrations from the DOC. The SCR estimator was used to evaluate the effect of NH3 and NOX sensors on state estimation quality. Three sensor combinations of NOX sensor only, NH3 sensor only and both NOX and NH3 sensors were evaluated. The NOX only configuration had the worst performance, the NH3 sensor only configuration was in the middle and both the NOX and NH3 sensor combination provided the best performance.

Sustainable Energy Production in the United States: Life Cycle Assessment of Biofuels and Bioenergy

The United States of America is making great efforts to transform the renewable and abundant biomass resources into cost-competitive, high-performance biofuels, bioproducts, and biopower. This is the key to increase domestic production of transportation fuels and renewable energy, and reduce greenhouse gas and other pollutant emissions. This dissertation focuses specifically on assessing the life cycle environmental impacts of biofuels and bioenergy produced from renewable feedstocks, such as lignocellulosic biomass, renewable oils and fats. The first part of the dissertation presents the life cycle greenhouse gas (GHG) emissions and energy demands of renewable diesel (RD) and hydroprocessed jet fuels (HRJ). The feedstocks include soybean, camelina, field pennycress, jatropha, algae, tallow and etc. Results show that RD and HRJ produced from these feedstocks reduce GHG emissions by over 50% compared to comparably performing petroleum fuels. Fossil energy requirements are also significantly reduced. The second part of this dissertation discusses the life cycle GHG emissions, energy demands and other environmental aspects of pyrolysis oil as well as pyrolysis oil derived biofuels and bioenergy. The feedstocks include waste materials such as sawmill residues, logging residues, sugarcane bagasse and corn stover, and short rotation forestry feedstocks such as hybrid poplar and willow. These LCA results show that as much as 98% GHG emission savings is possible relative to a petroleum heavy fuel oil. Life cycle GHG savings of 77 to 99% were estimated for power generation from pyrolysis oil combustion relative to fossil fuels combustion for electricity, depending on the biomass feedstock and combustion technologies used. Transportation fuels hydroprocessed from pyrolysis oil show over 60% of GHG reductions compared to petroleum gasoline and diesel. The energy required to produce pyrolysis oil and pyrolysis oil derived biofuels and bioelectricity are mainly from renewable biomass, as opposed to fossil energy. Other environmental benefits include human health, ecosystem quality and fossil resources. The third part of the dissertation addresses the direct land use change (dLUC) impact of forest based biofuels and bioenergy. An intensive harvest of aspen in Michigan is investigated to understand the GHG mitigation with biofuels and bioenergy production. The study shows that the intensive harvest of aspen in MI compared to business as usual (BAU) harvesting can produce 18.5 billion gallons of ethanol to blend with gasoline for the transport sector over the next 250 years, or 32.2 billion gallons of bio-oil by the fast pyrolysis process, which can be combusted to generate electricity or upgraded to gasoline and diesel. Intensive harvesting of these forests can result in carbon loss initially in the aspen forest, but eventually accumulates more carbon in the ecosystem, which translates to a CO2 credit from the dLUC impact. Time required for the forest-based biofuels to reach carbon neutrality is approximately 60 years. The last part of the dissertation describes the use of depolymerization model as a tool to understand the kinetic behavior of hemicellulose hydrolysis under dilute acid conditions. Experiments are carried out to measure the concentrations of xylose and xylooligomers during dilute acid hydrolysis of aspen. The experiment data are used to fine tune the parameters of the depolymerization model. The results show that the depolymerization model successfully predicts the xylose monomer profile in the reaction, however, it overestimates the concentrations of xylooligomers.

Ottimizzazione di una testata per un motore diesel aeronautico

In questo elaborato di tesi ci si è occupati di riprogettare la testata del motore bicilindrico Twin Air del gruppo Fiat. La testata viene ridisegnata al fine di poter destinare questo motore, particolarmente leggero flessibile e dai bassi consumi, ad un uso aeronautico. In questa tesi si è appunto realizzata una nuova testata inserendovi 3 valvole, due di aspirazione e una di scarico, e 2 iniettori per cilinrdo. Una volta completato il disegno sono stati realizzati diversi test attraverso un software di simulazione. In particolare ci si è accertati che la camera di combustione realizzata possa resistere alle alte pressioni e temperature in gioco e che i fluidi scorrano al meglio all'interno dei condotti. Si sono utilizzati i risultati ottenuti per riprogettare iterattivamente la testa ed arrivare a un risultato finale soddisfacente.

Sperimentazione di un EGR HP Mixer e di un Oil Cooler con Bypass in un motore V6 Diesel con l’obiettivo di ridurre la CO2

Lo scopo di questa tesi è stato sperimentare componenti prototipali su un motore V6 Diesel all’interno di un banco dinamico con il fine di valutarne la riduzione di CO2 in cicli di omologazione NEDC e WLTC. In particolare si sono studiati un nuovo EGR HP Mixer e un Oil Cooler dotato di Bypass: il primo componente per migliorare l’EGR distribution da cilindro a cilindro, mentre il secondo componente per ottenere un’ottimizzazione energetica della pompa dell’olio sfruttando il nuovo bypass del cooler. L’Oil Cooler è dotato di due cartucce intercambiabili che cambiano le fasi di bypass a seconda della temperatura dell’olio: la prima cartuccia, a 2 stadi, parte dalla condizione di bypass e chiude a una certa temperatura per proteggere il motore; la seconda, a 3 stadi, sfrutta il bypass solo in un range di temperatura ottimizzato con il calcolo CFD. La riduzione di consumi di gasolio è stata valutata confrontando i diversi consumi a pari emissioni di NOx; in questo modo si è registrata una riduzione di consumi con l’EGR HP Mixer dell’1.7% nel ciclo NEDC e dello 0.5% nel ciclo WLTC. Con lo stesso metodo si è registrato che l’Oil Cooler Bypass determina nel ciclo NEDC una riduzione dello 0.6 % con la valvola a 3 Stadi e una riduzione dello 0.37 % con la valvola a 2 Stadi. Nel ciclo WLTC si è invece ottenuta una riduzione dello 0.1 % con la valvola a 3 Stadi e un aumento dello 0.33 % con la valvola a 2 Stadi. Di ogni componente è stato fatto uno studio stazionario per indagarne a fondo i comportamenti.

Biobased Poli (dietilene furanoato) vs Poli (butilene furanoato): effetto degli atomi di ossigeno etereo sulle proprietà finali del materiale

Il presente lavoro di Tesi Magistrale nasce dall’esigenza di trovare soluzioni alle problematiche legate alla produzione e smaltimento delle plastiche, prevalentemente provenienti dal packaging alimentare. Una delle strategie maggiormente utilizzate in alternativa all’accumulo in discarica, è il riciclo. Questa soluzione ha però alcuni limiti: basse performance rispetto al materiale vergine e costi di processo troppo elevati a causa dei problemi di contaminazione e delle strutture multistrato. Alla luce di ciò, la ricerca scientifica si è orientata verso nuovi approcci come la sintesi di bioplastiche compostabili. Il poli(butilene furanoato) (PBF), è un buon candidato come materiale plastico per il packaging alimentare, ma possiede scarse caratteristiche di biodegradabilità e proprietà meccaniche non adeguate all’imballaggio flessibile. Per superare tali limitazioni, è stata messa a punto la sintesi di un nuovo poliestere, il poli(dietilene furanoato) (PDEF), un polimero biobased che si differenzia dal PBF per la presenza di un atomo di ossigeno etereo nella sub-unità glicolica. I due polimeri sono stati sottoposti ad una completa caratterizzazione chimico-fisica, con lo scopo di valutare l’effetto dell’introduzione di ossigeni eterei lungo la catena polimerica sulle proprietà finali del materiale. Oltre alla caratterizzazione molecolare e strutturale, è stato studiato anche il comportamento termico, la risposta meccanica e la permeabilità a diversi tipi di gas oltre che le caratteristiche di compostabilità. I risultati ottenuti hanno mostrato come nel PDEF vi sia un netto miglioramento delle proprietà non idonee per applicazioni nel packaging flessibile del PBF, in particolare quelle meccaniche, insieme a un ulteriore potenziamento delle già buone proprietà barriera. Inoltre, aspetto di fondamentale importanza nell’ottica della realizzazione di un materiale ecosostenibile, il PDEF mostra una velocità di degradazione in compost eccezionalmente elevata.

Estro: Rebirth of senses. Redesign di un fan coil attraverso un approccio sinestetico

L’attività di tesi ha come oggetto l’ipotesi di restyling del fan coil appartenente alla gamma Estro. Il progetto è nato durante il percorso di tirocinio curricolare ed è poi proseguito durante quello per tesi presso la Galletti s.p.a. Quando parliamo di restyling si intende inizialmente un intervento sulla parte estetica del prodotto, per poi arrivare ad un’analisi critica ed un ripensamento relativo alle funzionalità ed alle peculiarità che deve avere questo tipo di prodotto. Ciò si rende necessario perché il progetto della gamma Estro è ormai datato e nel corso degli anni le esigenze impiantistiche e le tendenze progettuali si sono notevolmente modificate, ad esempio si è passati da una prevalenza di modelli dotati di mobile di copertura, poiché installati a vista, ad una percentuale crescente di unità desinate ad essere installate a scomparsa ed incasso nei contro soffitti o in vani tecnici. Per l’ipotesi di redesign di Estro si è partiti col ripensare l’estetica del prodotto e affiancare tale cambiamento a nuove funzionalità da implementare attraverso un approccio sinestetico, rendendo così il fan coil capace di interfacciarsi con la sfera sensoriale della persona. Una prima ricerca si è focalizzata infatti sull’approfondimento di quella che la sfera sensoriale delle persone, andando ad individuare e studiare quelli che sono i sensi e gli organi di senso. Si è poi studiato come questa percezione simultanea di sensi avviene e quanto incida sul benessere indoor dell’utente, migliorandone le prestazioni psico-fisiche e aiutando le persone a sentirsi concentrate ed in forma. Infine si è deciso di implementare Estro facendolo interagire con i sensi, scegliendone le modalità adatte, il tutto affiancato anche dallo studio della nuova forma che va ad integrarsi con le nuove funzionalità che mirano al benessere dell’utente.

Modellazione grafica di elicotteri per la simulazione del volo

L'obiettivo di questo elaborato di tesi è la modellazione grafica delle cabine di pilotaggio di due elicotteri civili: si prevede una futura implementazione del modello di volo completo sul simulatore FlightGear. I due velivoli presi in considerazione sono stati sviluppati dall'azienda AgustaWestland e sono denominati AW109 e AW139. I modelli di volo sono composti da una parte grafica e dal modello dinamico del volo. La presente tesi si occupa del primo aspetto. Il lavoro di tesi è iniziato con una fase preliminare di ricerca che ha richiesto lo studio di come i modelli dinamici di volo siano implementati nel simulatore FlightGear; è stato, inoltre, approfondito l'utilizzo del linguaggio di markup XML necessario a descrivere il funzionamento e le caratteristiche dei velivoli in FlightGear. Ha fatto seguito la fase di scrittura dei file XML, facendo riferimento a modelli di elicotteri preesistenti e all'effettiva modellazione degli strumenti di bordo, attraverso il programma CAD Blender. Nella fase finale sono stati studiati e posizionati i vari strumenti principali di bordo, consultando i manuali degli elicotteri e ottenendo delle cabine di pilotaggio del tutto simili a quelle reali dei velivoli considerati. Gli sviluppi futuri di questo lavoro prevedono l'integrazione dei modelli grafici qui implementati nel modello di volo completo dei due elicotteri presi in considerazione.