Qualitative air flow modelling and analysis of data centre air conditioning as multiple jet array

This work identifies the importance of plenum pressure on the performance of the data centre. The present methodology followed in the industry considers the pressure drop across the tile as a dependant variable, but it is shown in this work that this is the only one independent variable that is responsible for the entire flow dynamics in the data centre, and any design or assessment procedure must consider the pressure difference across the tile as the primary independent variable. This concept is further explained by the studies on the effect of dampers on the flow characteristics. The dampers have found to introduce an additional pressure drop there by reducing the effective pressure drop across the tile. The effect of damper is to change the flow both in quantitative and qualitative aspects. But the effect of damper on the flow in the quantitative aspect is only considered while using the damper as an aid for capacity control. Results from the present study suggest that the use of dampers must be avoided in data centre and well designed tiles which give required flow rates must be used in the appropriate locations. In the present study the effect of hot air recirculation is studied with suitable assumptions. It identifies that, the pressure drop across the tile is a dominant parameter which governs the recirculation. The rack suction pressure of the hardware along with the pressure drop across the tile determines the point of recirculation in the cold aisle. The positioning of hardware in the racks play an important role in controlling the recirculation point. The present study is thus helpful in the design of data centre air flow, based on the theory of jets. The air flow can be modelled both quantitatively and qualitatively based on the results.

Socio economic factors influencing the persistence and control of filariasis in Kerala-A case study of malayan filariasis in Cherthala

In general the behavioural sciences have contributed very little to filariasis research.Man's actions in creating vector breeding sites have been noted and discussed frequently inthe frlariasis literature. but virtually no systematic studies of these fonns of behavior have been undertaken (Dunn. 1979). Human behavioural observations and inquires into values and attitudes atfecting behavior that inhibits or promotes vector breeding are essential if any progress is to be made in developing self help programmes of vector control. Therefore, a systematic study on the socio-economic aspect of the community is warranted before undertaking any control programme against filariasis. In view of this the present study has been carried out which reveals the knowledge, attitude and practice concerning the causation, transmission, treatment and control of the disease. Socio economic factors that influence the creation and maintenance of vector breeding habitats were identified. characterization and ranking of these sociological factors will be helpful in identifying the determinants of human behavioural changes towards the containment of the disease- Information on the existing indigenous perception of the disease and the factors that hinder the control will be useful in developing a sound strategy from the human angle, which can be put to practical use.

Photoacoustic and photothermal deflection studies on certain selected photonic materials“

The emergence of lasers in the early sixties has not only revolutionized the field of optics and communication but also paved new ways in the field of material characterization. Material studies using photothermal techniques possess certain unique characteristics and advantages over conventional methods. The most important aspect of photothennal techniques is their ability to perform noncontact and nondestructive measurement. Photoacoustics, photothermal deflection, thermal lens, photothermal radiometry and photopyroelectric methods are some of the commonly used and powerful techniques for the thermal and optical characterization of materials using lasers. In this thesis the applications of photoacoustic and photothermal deflection techniques for the thermal and optical characterization of different photonic materials, namely, semiconductors, liquid crystals and dye-doped polymers are discussed

Inter- State Variations in Productivity trends and Technological Change in Indian industry

The present study entitled ‘Inter-State Variations in Manufacturing Productivity and Technological Changes in India’ covers a period of 38 years from l960 tol998-99. The study is mainly based on ASI data. The study starts with a discussion of the major facilitating factors of industrialization, namely, historical forces, public policy and infrastructure facilities. These are discussed in greater details in the context of our discussion on Perrox’s (1998) ‘growth pole’ and ‘development pole’, Hirschman’s (1958) ‘industrial centers’ and Myrdal’s ‘spread effect’ Most of the existing literature more or less agrees that the process of industrialization has not been unifonn in all Indian states. There has been a decline in inter-state industrial disparities over time. This aspect is dealt at some length in the third chapter. An important element that deserves detailed attention is the intra-regional differences in industrialisation. Regional industrialisation implies the emergence of a few focal points and industrial regions. Calcutta, Bombay and Madras were the initial focal points. Later other centers like Bangalore, Amritsar, Ahemedabad etc. emerged as nodal points in other states. All major states account for focal points. The analysis made in the third chapter shows that industrial activities generally converge to one or two focal points and industrial regions have emerged out of the focal points in almost all states. One of the general features of these complexes and regions is that they approximately accommodate 50 to 75 percent of the total industrial units and workers in the state. Such convergence is seen hands in glow with urbanization. It was further seen that intra-regional industrial disparity comes down in industrial states like Maharashtra, Gujarat and Uttar Pradesh.

Spatio-temporal Variability of Atmospheric Ozone over Indian Subcontinent and its Relation to Meteorological Parameters

Ozone present in the atmosphere not only absorbs the biologically harmful ultraviolet radiation but also is an important ingredient of the climate system. The radiative absorption properties of ozone make it a determining factor in the structure of the atmosphere. Ozone in the troposphere has many negative impacts on humans and other living beings. Another significant aspect is the absorption of outgoing infrared radiation by ozone thus acting as a greenhouse gas. The variability of ozone in the atmosphere involves many interconnections with the incoming and outgoing radiation, temperature circulation etc. Hence ozone forms an important part of chemistry-climate as well as radiative transfer models. This aspect also makes the quantification of ozone more important. The discovery of Antarctic ozone hole and the role of anthropogenic activities in causing it made it possible to plan and implement necessary preventive measures. Continuous monitoring of ozone is also necessary to identify the effect of these preventive steps. The reactions involving the formation and destruction of ozone are influenced significantly by the temperature fluctuations of the atmosphere. On the other hand the variations in ozone can change the temperature structure of the atmosphere. Indian subcontinent is a region having large weather and climate variability which is evident from the large interannual variability of monsoon system over the region. Nearly half of Indian region comprises the tropical region. Most of ozone is formed in the tropical region and transported to higher latitudes. The formation and transport of ozone can be influenced by changes in solar radiation and various atmospheric circulation features. Besides industrial activities and vehicular traffic is more due to its large population. This may give rise to an increase in the production of tropospheric ozone which is greenhouse gas. Hence it becomes necessary to monitor the atmospheric ozone over this region. This study probes into the spatial distribution and temporal evolution of ozone over Indian subcontinent and discusses the contributing atmospheric parameters.

“Seaweed exudates and settlement behaviour of sedentary organisms"

The present investigation has looked exclusively into the aspect of the biological phenomenon of settling behaviour by two serious fouling offenders encountered in the tropical seas mainly on the hulls of ships and stationary structures in the harbours. The cue to study the behaviour was adopted from the observations so far made by scientists on the epizoic growth of these organisms on the surfaces of algal fronds of variegated shape, texture, size etc. The results do indicate that there are sufficient qualities of bioactive substances produced by plants occupying the lowest categories in organic evolution and curiously enough these substances have withstood the test of time.

On the Growth Mechanism of Nickel and Cobalt Nanowires and Comparison of Their Magnetic Properties

Magnetic nanowires (NWs) are ideal materials for the fabrication of various multifunctional nanostructures which can be manipulated by an external magnetic fi eld. Highly crystalline and textured nanowires of nickel (Ni NWs) and cobalt (Co NWs) with high aspect ratio (~330) and high coercivity have been synthesized by electrodeposition using nickel sulphate hexahydrate (NiSO4·6H2O) and cobalt sulphate heptahydrate (CoSO4·7H2O) respectively on nanoporous alumina membranes. They exhibit a preferential growth along〈110〉. A general mobility assisted growth mechanism for the formation of Ni and Co NWs is proposed. The role of the hydration layer on the resulting one-dimensional geometry in the case of potentiostatic electrodeposition is verified. A very high interwire interaction resulting from magnetostatic dipolar interactions between the nanowires is observed. An unusual low-temperature magnetisation switching for fi eld parallel to the wire axis is evident from the peculiar high fi eld M(T) curve

Synthesis, Characterization and Applications of Modified TiO2 Systems

This thesis is divided in to 9 chapters and deals with the modification of TiO2 for various applications include photocatalysis, thermal reaction, photovoltaics and non-linear optics. Chapter 1 involves a brief introduction of the topic of study. An introduction to the applications of modified titania systems in various fields are discussed concisely. Scope and objectives of the present work are also discussed in this chapter. Chapter 2 explains the strategy adopted for the synthesis of metal, nonmetal co-doped TiO2 systems. Hydrothermal technique was employed for the preparation of the co-doped TiO2 system, where Ti[OCH(CH3)2]4, urea and metal nitrates were used as the sources for TiO2, N and metals respectively. In all the co-doped systems, urea to Ti[OCH(CH3)2]4 was taken in a 1:1 molar ratio and varied the concentration of metals. Five different co-doped catalytic systems and for each catalysts, three versions were prepared by varying the concentration of metals. A brief explanation of physico-chemical techniques used for the characterization of the material was also presented in this chapter. This includes X-ray Diffraction (XRD), Raman Spectroscopy, FTIR analysis, Thermo Gravimetric Analysis, Energy Dispersive X-ray Analysis (EDX), Scanning Electron Microscopy(SEM), UV-Visible Diffuse Reflectance Spectroscopy (UV-Vis DRS), Transmission Electron Microscopy (TEM), BET Surface Area Measurements and X-ray Photoelectron Spectroscopy (XPS). Chapter 3 contains the results and discussion of characterization techniques used for analyzing the prepared systems. Characterization is an inevitable part of materials research. Determination of physico-chemical properties of the prepared materials using suitable characterization techniques is very crucial to find its exact field of application. It is clear from the XRD pattern that photocatalytically active anatase phase dominates in the calcined samples with peaks at 2θ values around 25.4°, 38°, 48.1°, 55.2° and 62.7° corresponding to (101), (004), (200), (211) and (204) crystal planes (JCPDS 21-1272) respectively. But in the case of Pr-N-Ti sample, a new peak was observed at 2θ = 30.8° corresponding to the (121) plane of the polymorph brookite. There are no visible peaks corresponding to dopants, which may be due to their low concentration or it is an indication of the better dispersion of impurities in the TiO2. Crystallite size of the sample was calculated from Scherrer equation byusing full width at half maximum (FWHM) of the (101) peak of the anatase phase. Crystallite size of all the co-doped TiO2 was found to be lower than that of bare TiO2 which indicates that the doping of metal ions having higher ionic radius into the lattice of TiO2 causes some lattice distortion which suppress the growth of TiO2 nanoparticles. The structural identity of the prepared system obtained from XRD pattern is further confirmed by Raman spectra measurements. Anatase has six Raman active modes. Band gap of the co-doped system was calculated using Kubelka-Munk equation and that was found to be lower than pure TiO2. Stability of the prepared systems was understood from thermo gravimetric analysis. FT-IR was performed to understand the functional groups as well as to study the surface changes occurred during modification. EDX was used to determine the impurities present in the system. The EDX spectra of all the co-doped samples show signals directly related to the dopants. Spectra of all the co-doped systems contain O and Ti as the main components with low concentrations of doped elements. Morphologies of the prepared systems were obtained from SEM and TEM analysis. Average particle size of the systems was drawn from histogram data. Electronic structures of the samples were identified perfectly from XPS measurements. Chapter 4 describes the photocatalytic degradation of herbicides Atrazine and Metolachlor using metal, non-metal co-doped titania systems. The percentage of degradation was analyzed by HPLC technique. Parameters such as effect of different catalysts, effect of time, effect of catalysts amount and reusability studies were discussed. Chapter 5 deals with the photo-oxidation of some anthracene derivatives by co-doped catalytic systems. These anthracene derivatives come underthe category of polycyclic aromatic hydrocarbons (PAH). Due to the presence of stable benzene rings, most of the PAH show strong inhibition towards biological degradation and the common methods employed for their removal. According to environmental protection agency, most of the PAH are highly toxic in nature. TiO2 photochemistry has been extensively investigated as a method for the catalytic conversion of such organic compounds, highlighting the potential of thereof in the green chemistry. There are actually two methods for the removal of pollutants from the ecosystem. Complete mineralization is the one way to remove pollutants. Conversion of toxic compounds to another compound having toxicity less than the initial starting compound is the second way. Here in this chapter, we are concentrating on the second aspect. The catalysts used were Gd(1wt%)-N-Ti, Pd(1wt%)-N-Ti and Ag(1wt%)-N-Ti. Here we were very successfully converted all the PAH to anthraquinone, a compound having diverse applications in industrial as well as medical fields. Substitution of 10th position of desired PAH by phenyl ring reduces the feasibility of photo reaction and produced 9-hydroxy 9-phenyl anthrone (9H9PA) as an intermediate species. The products were separated and purified by column chromatography using 70:30 hexane/DCM mixtures as the mobile phase and the resultant products were characterized thoroughly by 1H NMR, IR spectroscopy and GCMS analysis. Chapter 6 elucidates the heterogeneous Suzuki coupling reaction by Cu/Pd bimetallic supported on TiO2. Sol-Gel followed by impregnation method was adopted for the synthesis of Cu/Pd-TiO2. The prepared system was characterized by XRD, TG-DTG, SEM, EDX, BET Surface area and XPS. The product was separated and purified by column chromatography using hexane as the mobile phase. Maximum isolated yield of biphenyl of around72% was obtained in DMF using Cu(2wt%)-Pd(4wt%)-Ti as the catalyst. In this reaction, effective solvent, base and catalyst were found to be DMF, K2CO3 and Cu(2wt%)-Pd(4wt%)-Ti respectively. Chapter 7 gives an idea about the photovoltaic (PV) applications of TiO2 based thin films. Due to energy crisis, the whole world is looking for a new sustainable energy source. Harnessing solar energy is one of the most promising ways to tackle this issue. The present dominant photovoltaic (PV) technologies are based on inorganic materials. But the high material, low power conversion efficiency and manufacturing cost limits its popularization. A lot of research has been conducted towards the development of low-cost PV technologies, of which organic photovoltaic (OPV) devices are one of the promising. Here two TiO2 thin films having different thickness were prepared by spin coating technique. The prepared films were characterized by XRD, AFM and conductivity measurements. The thickness of the films was measured by Stylus Profiler. This chapter mainly concentrated on the fabrication of an inverted hetero junction solar cell using conducting polymer MEH-PPV as photo active layer. Here TiO2 was used as the electron transport layer. Thin films of MEH-PPV were also prepared using spin coating technique. Two fullerene derivatives such as PCBM and ICBA were introduced into the device in order to improve the power conversion efficiency. Effective charge transfer between the conducting polymer and ICBA were understood from fluorescence quenching studies. The fabricated Inverted hetero junction exhibited maximum power conversion efficiency of 0.22% with ICBA as the acceptor molecule. Chapter 8 narrates the third order order nonlinear optical properties of bare and noble metal modified TiO2 thin films. Thin films were fabricatedby spray pyrolysis technique. Sol-Gel derived Ti[OCH(CH3)2]4 in CH3CH2OH/CH3COOH was used as the precursor for TiO2. The precursors used for Au, Ag and Pd were the aqueous solutions of HAuCl4, AgNO3 and Pd(NO3)2 respectively. The prepared films were characterized by XRD, SEM and EDX. The nonlinear optical properties of the prepared materials were investigated by Z-Scan technique comprising of Nd-YAG laser (532 nm,7 ns and10 Hz). The non-linear coefficients were obtained by fitting the experimental Z-Scan plot with the theoretical plots. Nonlinear absorption is a phenomenon defined as a nonlinear change (increase or decrease) in absorption with increasing of intensity. This can be mainly divided into two types: saturable absorption (SA) and reverse saturable absorption (RSA). Depending on the pump intensity and on the absorption cross- section at the excitation wavelength, most molecules show non- linear absorption. With increasing intensity, if the excited states show saturation owing to their long lifetimes, the transmission will show SA characteristics. Here absorption decreases with increase of intensity. If, however, the excited state has strong absorption compared with that of the ground state, the transmission will show RSA characteristics. Here in our work most of the materials show SA behavior and some materials exhibited RSA behavior. Both these properties purely depend on the nature of the materials and alignment of energy states within them. Both these SA and RSA have got immense applications in electronic devices. The important results obtained from various studies are presented in chapter 9.

Lithography-free micro- and nanostructuring based on conventional plasma etching

In now-a-days semiconductor and MEMS technologies the photolithography is the working horse for fabrication of functional devices. The conventional way (so called Top-Down approach) of microstructuring starts with photolithography, followed by patterning the structures using etching, especially dry etching. The requirements for smaller and hence faster devices lead to decrease of the feature size to the range of several nanometers. However, the production of devices in this scale range needs photolithography equipment, which must overcome the diffraction limit. Therefore, new photolithography techniques have been recently developed, but they are rather expensive and restricted to plane surfaces. Recently a new route has been presented - so-called Bottom-Up approach - where from a single atom or a molecule it is possible to obtain functional devices. This creates new field - Nanotechnology - where one speaks about structures with dimensions 1 - 100 nm, and which has the possibility to replace the conventional photolithography concerning its integral part - the self-assembly. However, this technique requires additional and special equipment and therefore is not yet widely applicable. This work presents a general scheme for the fabrication of silicon and silicon dioxide structures with lateral dimensions of less than 100 nm that avoids high-resolution photolithography processes. For the self-aligned formation of extremely small openings in silicon dioxide layers at in depth sharpened surface structures, the angle dependent etching rate distribution of silicon dioxide against plasma etching with a fluorocarbon gas (CHF3) was exploited. Subsequent anisotropic plasma etching of the silicon substrate material through the perforated silicon dioxide masking layer results in high aspect ratio trenches of approximately the same lateral dimensions. The latter can be reduced and precisely adjusted between 0 and 200 nm by thermal oxidation of the silicon structures owing to the volume expansion of silicon during the oxidation. On the basis of this a technology for the fabrication of SNOM calibration standards is presented. Additionally so-formed trenches were used as a template for CVD deposition of diamond resulting in high aspect ratio diamond knife. A lithography-free method for production of periodic and nonperiodic surface structures using the angular dependence of the etching rate is also presented. It combines the self-assembly of masking particles with the conventional plasma etching techniques known from microelectromechanical system technology. The method is generally applicable to bulk as well as layered materials. In this work, layers of glass spheres of different diameters were assembled on the sample surface forming a mask against plasma etching. Silicon surface structures with periodicity of 500 nm and feature dimensions of 20 nm were produced in this way. Thermal oxidation of the so structured silicon substrate offers the capability to vary the fill factor of the periodic structure owing to the volume expansion during oxidation but also to define silicon dioxide surface structures by selective plasma etching. Similar structures can be simply obtained by structuring silicon dioxide layers on silicon. The method offers a simple route for bridging the Nano- and Microtechnology and moreover, an uncomplicated way for photonic crystal fabrication.

Profile simulations of gas chopping etching processes : model development and comparison with experiments

The progress in microsystem technology or nano technology places extended requirements to the fabrication processes. The trend is moving towards structuring within the nanometer scale on the one hand, and towards fabrication of structures with high aspect ratio (ratio of vertical vs. lateral dimensions) and large depths in the 100 µm scale on the other hand. Current procedures for the microstructuring of silicon are wet chemical etching and dry or plasma etching. A modern plasma etching technique for the structuring of silicon is the so-called "gas chopping" etching technique (also called "time-multiplexed etching"). In this etching technique, passivation cycles, which prevent lateral underetching of sidewalls, and etching cycles, which etch preferably in the vertical direction because of the sidewall passivation, are constantly alternated during the complete etching process. To do this, a CHF3/CH4 plasma, which generates CF monomeres is employed during the passivation cycle, and a SF6/Ar, which generates fluorine radicals and ions plasma is employed during the etching cycle. Depending on the requirements on the etched profile, the durations of the individual passivation and etching cycles are in the range of a few seconds up to several minutes. The profiles achieved with this etching process crucially depend on the flow of reactants, i.e. CF monomeres during the passivation cycle, and ions and fluorine radicals during the etching cycle, to the bottom of the profile, especially for profiles with high aspect ratio. With regard to the predictability of the etching processes, knowledge of the fundamental effects taking place during a gas chopping etching process, and their impact onto the resulting profile is required. For this purpose in the context of this work, a model for the description of the profile evolution of such etching processes is proposed, which considers the reactions (etching or deposition) at the sample surface on a phenomenological basis. Furthermore, the reactant transport inside the etching trench is modelled, based on angular distribution functions and on absorption probabilities at the sidewalls and bottom of the trench. A comparison of the simulated profiles with corresponding experimental profiles reveals that the proposed model reproduces the experimental profiles, if the angular distribution functions and absorption probabilities employed in the model is in agreement with data found in the literature. Therefor the model developed in the context of this work is an adequate description of the effects taking place during a gas chopping plasma etching process.

Preparation and applications of periodical gold nanoparticle arrays

Diese Arbeit beschäftigt sich mit der Herstellung und Anwendungen von periodischen Goldnanopartikel-Arrays (PPAs), die mit Hilfe von Nanosphären-Lithografie hergestellt wurden. In Abhängigkeit der verwendeten Nanosphären-Größe wurden dabei entweder kleine dreieckige Nanopartikel (NP) (bei Verwendung von Nanosphären mit einem Durchmesser von 330 nm) oder große dreieckige NPD sowie leicht gestreckte NP (bei Verwendung von Nanosphären mit einem Durchmesser von 1390 nm) hergestellt. Die Charakterisierung der PPAs erfolgte mit Hilfe von Rasterkraftmikroskopie, Rasterelektronenmikroskopie und optischer Spektroskopie. Die kleinen NP besitzen ein Achsverhältnis (AV) von 2,47 (Kantenlänge des NPs: (74+/-6) nm, Höhe: (30+/-4) nm. Die großen dreieckigen NP haben ein AV von 3 (Kantenlänge des NPs:(465+/-27) nm, Höhe: (1530+/-10) nm) und die leicht gestreckten NP (die aufgrund der Ausbildung von Doppelschichten ebenfalls auf der gleichen Probe erzeugt wurden) haben eine Länge von (364+/-16)nm, eine Breite von (150+/-20) nm und eine Höhe von (150+/-10)nm. Die optischen Eigenschaften dieser NP werden durch lokalisierte Oberflächenplasmon-Polariton Resonanzen (LPPRs) dominiert, d.h. von einem eingestrahlten elektromagnetischen Feld angeregte kollektive Schwingungen der Leitungsbandelektronen. In dieser Arbeit wurden drei signifikante Herausforderungen für Plasmonik-Anwendungen bearbeitet, welche die einzigartigen optischen Eigenschaften dieser NP ausnutzen. Erstens wurden Ergebnisse der selektiven und präzisen Größenmanipulation und damit einer Kontrolle der interpartikulären Abstände von den dreieckigen Goldnanopartikel mit Hilfe von ns-gepulstem Laserlicht präsentiert. Die verwendete Methode basiert hierbei auf der Größen- und Formabhängigkeit der LPPRs der NP. Zweitens wurde die sensorischen Fähigkeiten von Gold-NP ausgenutzt, um die Bildung von molekularen Drähten auf den PPAs durch schrittweise Zugabe von unterschiedlichen molekularen Spezies zu untersuchen. Hierbei wurde die Verschiebung der LSPPR in den optischen Spektren dazu ausgenutzt, die Bildung der Nanodrähte zu überwachen. Drittens wurden Experimente vorgestellt, die sich die lokale Feldverstärkung von NP zu nutze machen, um eine hochgeordnete Nanostrukturierung von Oberflächen mittels fs-gepulstem Laserlicht zu bewerkstelligen. Dabei zeigt sich, dass neben der verwendeten Fluenz die Polarisationsrichtung des eingestrahlten Laserlichts in Bezug zu der NP-Orientierung sowie die Größe der NP äußerst wichtige Parameter für die Nanostrukturierung darstellen. So konnten z.B. Nanolöcher erzeugt werden, die bei höheren Fluenzen zu Nanogräben und Nanokanälen zusammen wuchsen. Zusammengefasst lässt sich sagen, dass die in dieser Arbeit gewonnen Ergebnisse von enormer Wichtigkeit für weitere Anwendungen sind.

Ferrocene-Based Pyridylphosphine Ligands – Coordination Chemistry of Group 10, 11 and 12 Metals

English: The present thesis describes the synthesis of 1,1’-ferrocendiyl-based pyridylphosphine ligands, the exploration of their fundamental coordination chemistry and preliminary experiments with selected complexes aimed at potential applications. One main aspect is the synthesis of the bidentate ferrocene-based pyridylphosphine ligands 1-(Pyrid-2-yl)-1’-diphenylphosphinoferrocene, 1-(Pyrid-3-yl)-1’-diphenylphosphinoferrocene and 1-[(Pyrid-2-yl)methyl]-1’-diphenylphosphinoferrocene. A specific feature of these ligands is the ball-bearing like flexibility of the ferrocenebased backbone. An additional flexibility element is the rotation around the C–C single bonds. Consequently, the donor atoms can realise a wide range of positions with respect to each other and are therefore able to adapt to the coordination requirements of different metal centres. The flexibility of the ligand also plays a role in another key aspect of this work, which concerns the coordination mode, i. e. bridging vs. chelating. In addition to the flexibility, also the position of the donor atoms to each other is important. This is largely affected by the position of the pyridyl nitrogen (pyrid-2-yl vs. pyrid-3-yl) and the methylen group in 1-[(Pyrid-2-yl)methyl]-1’-diphenylphosphinoferrocene. Another interesting point is the combination of a soft phosphorus donor atom with a harder nitrogen donor atom, according to the HSAB principle. This combination generates a unique binding profile, since the pi-acceptor character of the P site is able to stabilise a metal centre in a low oxidation state, while the nitrogen sigma-donor ability can make the metal more susceptible to oxidative addition reactions. A P,N-donor combination can afford hemilabile binding profiles, which would be ideal for catalysis. Beyond 1,2-substituted ferrocene derivatives, which are quite successful in catalytic applications, 1,1’-derivatives are rather underrepresented. While a low-yield synthetic pathway to 1-(Pyrid-2-yl)-1’-diphenylphosphinoferrocene was already described in the literature [I. R. Butler, Organometallics 1992, 11, 74.], it was possible to find a new, improved and simplified synthetic pathway. Both other ligands were unknown prior to this work. Satisfactory results in the synthesis of 1-(Pyrid-3-yl)-1’-diphenylphosphinoferrocene could be achieved by working in analogy to the new synthetic procedure for 1-(Pyrid-2-yl)-1’-diphenylphosphinoferrocene. The synthesis of 1-[(Pyrid-2-yl)methyl]-1’-diphenylphosphinoferrocene has been handled by the group of Prof. Petr Stepnicka from Charles University, Prague, Czech Republic. The synthesis of tridentate ligands with an analogous heterodentate arrangement, was investigated briefly as a sideline of this study. The major part of this thesis deals with the fundamental coordination chemistry towards transition metals of the groups 10, 11 and 12. Due to the well-established catalytic properties of analogous palladium complexes, the coordination chemistry towards palladium (group 10) is of particular interest. The metals zinc and cadmium (group 12) are also of substantial importance because they are redox-inert in their divalent state. This is relevant in view of electrochemical investigations concerning the utilisation of the ligands as molecular redox sensors. Also mercury and the monovalent metals silver and gold (group 11) are included because of their rich coordination chemistry. It is essential to answer questions concerning aspects of the ligands’ coordination mode bearing in mind the HSAB principle.

Higher Education Governance in Vietnam: University Action, the State and Changing Relationships

Diese Dissertation stellt eine Studie da, welche sich mit den Änderungen in der Governance der Hochschulbildung in Vietnam beschäftigt. Das zentrale Ziel dieser Forschungsarbeit ist die Untersuchung der Herkunft und Änderung in der Beziehung der Mächte zwischen dem vietnamesischen Staat und den Hochschulbildungsinstituten (HI), welche hauptsächlich aus der Interaktion dieser beiden Akteure resultiert. Die Macht dieser beiden Akteure wurde im sozialen Bereich konstruiert und ist hauptsächlich durch ihre Nützlichkeit und Beiträge für die Hochschulbildung bestimmt. Diese Arbeit beschäftigt sich dabei besonders mit dem Aspekt der Lehrqualität. Diese Studie nimmt dabei die Perspektive einer allgemeinen Governance ein, um die Beziehung zwischen Staat und HI zu erforschen. Zudem verwendet sie die „Resource Dependence Theory“ (RDT), um das Verhalten der HI in Bezug auf die sich verändernde Umgebung zu untersuchen, welche durch die Politik und eine abnehmende Finanzierung charakterisiert ist. Durch eine empirische Untersuchung der Regierungspolitik sowie der internen Steuerung und den Praktiken der vier führenden Universitäten kommt die Studie zu dem Schluss, dass unter Berücksichtigung des Drucks der Schaffung von Einkommen die vietnamesischen Universitäten sowohl Strategien als auch Taktiken entwickelt haben, um Ressourcenflüsse und Legitimität zu kontrollieren. Die Entscheidungs- und Zielfindung der Komitees, die aus einer Mehrheit von Akademikern bestehen, sind dabei mächtiger als die der Manager. Daher werden bei initiativen Handlungen der Universitäten größtenteils Akademiker mit einbezogen. Gestützt auf die sich entwickelnden Muster der Ressourcenbeiträge von Akademikern und Studierenden für die Hochschulbildung prognostiziert die Studie eine aufstrebende Governance Konfiguration, bei der die Dimensionen der akademischen Selbstverwaltung und des Wettbewerbsmarktes stärker werden und die Regulation des Staates rational zunimmt. Das derzeitige institutionelle Design und administrative System des Landes, die spezifische Gewichtung und die Koordinationsmechanismen, auch als sogenanntes effektives Aufsichtssystem zwischen den drei Schlüsselakteuren - der Staat, die HI/Akademiker und die Studierenden – bezeichnet, brauchen eine lange Zeit zur Detektion und Etablierung. In der aktuellen Phase der Suche nach einem solchen System sollte die Regierung Management-Tools stärken, wie zum Beispiel die Akkreditierung, belohnende und marktbasierte Instrumente und das Treffen informations-basierter Entscheidungen. Darüber hinaus ist es notwendig die Transparenz der Politik zu erhöhen und mehr Informationen offenzulegen.

Prevalence of intestinal parasites in small ruminants and their senstivity to treatments with ethnobotanical remedies in Cholistan, Pakistan

Livestock production contributes substantially to the livelihoods of poor rural farmers in Pakistan; strengthening pastoral communities plays an imperative role in the country’s thrive for poverty alleviation. Intestinal helminths constitute a major threat for pastoral livestock keepers in the whole country because chronic infestation leads to distinct losses in livestock productivity, particularly the growth of young animals. Synthetic anthelmintics have long been considered the only effective way of controlling this problem but high prices, side effects and chemical residues/toxicity problems, or development of resistance, lead to their very limited use in many pastoral systems. Additionally, poor pastoralists in remote areas of Pakistan hardly have access to appropriate anthelmintic drugs, which are also relatively expensive due to the long routes of transportation. The search for new and more sustainable ways of supporting livestock keepers in remote areas has given rise to studies of ethno-botanicals or traditional plant-based remedies to be used in livestock health care. Plant-based remedies are cheap or free of cost, environmentally safe and generally create no problem of drug resistance; they thus might substitute allopathic drugs. Furthermore, these remedies are easily available in remote areas and simple to prepare and/or administer. Cholistan desert is a quite poor region of Pakistan and the majority of its inhabitants are practicing a nomadic life. The region’s total livestock population (1.29 million heads) is almost twice that of the human population. Livestock husbandry is the primordial occupation of the communities and traditionally wealth assessment was based on the number of animals, especially goats and sheep, owned by an individual. Fortunately, about 60% of this desert region is richly endowed with highly adapted grasses, shrubs and trees. This natural flora has a rich heritage of scientifically unexplored botanical pharmacopoeia. Against this background, the present research project that was conducted under the umbrella of the International Center for Development and Decent Work at Kassel University, focused on a development aspect: in the Cholistan desert region it was firstly examined how pastoralists manage their livestock, which major health problems they face for the different animal species, and which of the naturally occurring plants they use for the treatment of animal diseases (Chapter 2). For this purpose, a baseline survey was carried out across five locations in Cholistan, using a structured questionnaire to collect data from 100 livestock farmers (LF) and 20 local healers (LH). Most of LF and LH were illiterate (66%; 70%). On average, LH had larger herds (109 animals) than LF (85 animals) and were more experienced in livestock husbandry and management. On average LF spent about 163 Euro per year on the treatment of their livestock, with a huge variability in expenditures. Eighty-six traditional remedies based on 64 plants belonging to 43 families were used. Capparaceae was the botanical family with the largest number of species used (4), followed by Chenopodiaceae, Poaceae, Solanaceae and Zygophyllaceae (3). The plants Capparis decidua (n=55 mentions), Salsola foetida (n=52), Suaeda fruticosa (n=46), Haloxylon salicornicum (n=42) and Haloxylon recurvum (n=39) were said to be most effective against the infestations with gastrointestinal parasites. Aerial parts (43%), leaves (26%), fruits (9%), seeds and seed oils (9%) were the plant parts frequently used for preparation of remedies, while flowers, roots, bulbs and pods were less frequently used (<5%). Common preparations were decoction, jaggery and ball drench; oral drug administration was very common. There was some variation in the doses used for different animal species depending on age, size and physical condition of the animal and severity of the disease. In a second step the regionally most prevalent gastrointestinal parasites of sheep and goats were determined (Chapter 3) in 500 animals per species randomly chosen from pastoral herds across the previously studied five localities. Standard parasitological techniques were applied to identify the parasites in faecal samples manually collected at the rectum. Overall helminth prevalence was 78.1% across the 1000 animals; pure nematode infestations were most prevalent (37.5%), followed by pure trematode (7.9%), pure cestode (2.6%) and pure protozoa infestations (0.8%). Mixed infestations with nematodes and trematodes occurred in 6.4% of all animals, mixed nematode-cestode infestations in 3.8%, and all three groups were found in 19.1% of the sheep and goats. In goats more males (81.1%) than females (77.0%) were infested, the opposite was found in sheep (73.6% males, 79.5% females). Parasites were especially prevalent in suckling goats (85.2%) and sheep (88.5%) and to a lesser extent in young (goats 80.6%, sheep 79.3%) and adult animals (goats 72.8%, sheep 73.8%). Haemonchus contortus, Trichuris ovis and Paramphistomum cervi were the most prevalent helminths. In a third step the in vitro anthelmintic activity of C. decidua, S. foetida, S. fruticosa, H. salicornicum and H. recurvum (Chapter 2) was investigated against adult worms of H. contortus, T. ovis and P. cervi (Chapter 3) via adult motility assay (Chapter 4). Various concentrations ranging from 7.8 to 500 mg dry matter/ml of three types of extracts of each plant, i.e. aqueous, methanol, and aqueous-methanol (30:70), were used at different time intervals to access their anthelmintic activity. Levamisol (0.55 mg/ml) and oxyclozanide (30 mg/ml) served as positive and phosphate-buffered saline as negative control. All extracts exhibited minimum and maximum activity at 2 h and 12 h after parasite exposure; the 500 mg/ml extract concentrations were most effective. Plant species (P<0.05), extract type (P<0.01), parasite species (P<0.01), extract concentration (P<0.01), time of exposure (P<0.01) and their interactions (P<0.01) had significant effects on the number of immobile/dead helminths. From the comparison of LC50 values it appeared that the aqueous extract of C. decidua was more potent against H. contortus and T. ovis, while the aqueous extract of S. foetida was effective against P. cervi. The methanol extracts of H. recurvum were most potent against all three types of parasites, and its aqueous-methanol extract was also very effective against T. ovis and P. cervi. Based on these result it is concluded that the aqueous extract of C. decidua, as well as the methanol and aqueous-methanol extract of H. recurvum have the potential to be developed into plant-based drugs for treatment against H. contortus, T. ovis and P. cervi infestations. Further studies are now needed to investigate the in vivo anthelmintic activity of these plants and plant extracts, respectively, in order to develop effective, cheap and locally available anthelmintics for pastoralists in Cholistan and neighboring desert regions. This will allow developing tangible recommendations for plant-based anthelminthic treatment of sheep and goat herds, and by this enable pastoralists to maintain healthy and productive flocks at low costs and probably even manufacture herbal drugs for marketing on a regional scale.

Individual Decision-Making and Inflation Persistence

The traditional task of a central bank is to preserve price stability and, in doing so, not to impair the real economy more than necessary. To meet this challenge, it is of great relevance whether inflation is only driven by inflation expectations and the current output gap or whether it is, in addition, influenced by past inflation. In the former case, as described by the New Keynesian Phillips curve, the central bank can immediately and simultaneously achieve price stability and equilibrium output, the so-called ‘divine coincidence’ (Blanchard and Galí 2007). In the latter case, the achievement of price stability is costly in terms of output and will be pursued over several periods. Similarly, it is important to distinguish this latter case, which describes ‘intrinsic’ inflation persistence, from that of ‘extrinsic’ inflation persistence, where the sluggishness of inflation is not a ‘structural’ feature of the economy but merely ‘inherited’ from the sluggishness of the other driving forces, inflation expectations and output. ‘Extrinsic’ inflation persistence is usually considered to be the less challenging case, as policy-makers are supposed to fight against the persistence in the driving forces, especially to reduce the stickiness of inflation expectations by a credible monetary policy, in order to reestablish the ‘divine coincidence’. The scope of this dissertation is to contribute to the vast literature and ongoing discussion on inflation persistence: Chapter 1 describes the policy consequences of inflation persistence and summarizes the empirical and theoretical literature. Chapter 2 compares two models of staggered price setting, one with a fixed two-period duration and the other with a stochastic duration of prices. I show that in an economy with a timeless optimizing central bank the model with the two-period alternating price-setting (for most parameter values) leads to more persistent inflation than the model with stochastic price duration. This result amends earlier work by Kiley (2002) who found that the model with stochastic price duration generates more persistent inflation in response to an exogenous monetary shock. Chapter 3 extends the two-period alternating price-setting model to the case of 3- and 4-period price durations. This results in a more complex Phillips curve with a negative impact of past inflation on current inflation. As simulations show, this multi-period Phillips curve generates a too low degree of autocorrelation and too early turnings points of inflation and is outperformed by a simple Hybrid Phillips curve. Chapter 4 starts from the critique of Driscoll and Holden (2003) on the relative real-wage model of Fuhrer and Moore (1995). While taking the critique seriously that Fuhrer and Moore’s model will collapse to a much simpler one without intrinsic inflation persistence if one takes their arguments literally, I extend the model by a term for inequality aversion. This model extension is not only in line with experimental evidence but results in a Hybrid Phillips curve with inflation persistence that is observably equivalent to that presented by Fuhrer and Moore (1995). In chapter 5, I present a model that especially allows to study the relationship between fairness attitudes and time preference (impatience). In the model, two individuals take decisions in two subsequent periods. In period 1, both individuals are endowed with resources and are able to donate a share of their resources to the other individual. In period 2, the two individuals might join in a common production after having bargained on the split of its output. The size of the production output depends on the relative share of resources at the end of period 1 as the human capital of the individuals, which is built by means of their resources, cannot fully be substituted one against each other. Therefore, it might be rational for a well-endowed individual in period 1 to act in a seemingly ‘fair’ manner and to donate own resources to its poorer counterpart. This decision also depends on the individuals’ impatience which is induced by the small but positive probability that production is not possible in period 2. As a general result, the individuals in the model economy are more likely to behave in a ‘fair’ manner, i.e., to donate resources to the other individual, the lower their own impatience and the higher the productivity of the other individual. As the (seemingly) ‘fair’ behavior is modelled as an endogenous outcome and as it is related to the aspect of time preference, the presented framework might help to further integrate behavioral economics and macroeconomics.